Alarm Controls SREX-100 Installation Instructions

ACTIVE INFRARED

REQUEST TO EXIT SENSOR

MODEL SREX-100

OPERATING INSTRUCTIONS

PN:111

YOUR SOURCE FOR QUALITY

SECURITY EQUIPMENT

MAGNETIC LOCKS

REQUEST TO EXIT STATIONS

DIGITAL KEYPADS

PUSHBUTTON CONTROL STATIONS

PNEUMATIC TIME DELAY STATIONS

VANDAL RESISTANT PUSH PLATES

MORTISE CYLINDER STATIONS

EXPLOSION-PROOF STATIONS

VANDAL RESISTANT STATIONS

EIGHT ZONE ANNUNCIATORS

CUSTOM GRAPHIC ANNUNCIATORS

PUSH BARS

RELAYS

ALARM
CONTROLS

713

ALARM
CONTROLS

WWW.ALARMCONTROLS.COM

ASSA ABLOY, the global leader
in door opening solutions

ASSA ABLOY, the global leader
in door opening solutions

SPECIFICATION

 OPERATING VOLTAGE: 12 OR 24 VOLTS AC/DC, AUTO VOLTAGE SELECTION
 CURRENT DRAW: 155 MA., (SOUNDER OFF), 200 MA., (SOUNDER MAXIMUM VOLUME)
 RELAY CONTACT RATING: 1.3 A. @ 30 VOLTS DC OR 24 VOLTS AC
 RELAY CONTACT ARRANGEMENT: DOUBLE POLE-DOUBLE THROW, (2 FORM C)
 TEMPERATURE: FOR U.L. LISTED INSTALLATIONS +32 F TO +120 F, (0 C TO +49C)
 HUMIDITY: 0% TO 93% NON-CONDENSING FOR ULC-S319 INSTALLATIONS, 0% TO 85%

NON-CONDENSING FOR UL-294 LISTED INSTALL

ATIONS.

 REQUEST TO EXIT INPUT: NORMALLY-OPEN DRY CONTACTS
 KEYPAD OR CARD READER INPUT: NORMALLY-CLOSED DRY CONTACTS
 DOOR POSITION SWITCH INPUT: NORMALLY-OPEN DRY CONTACTS
 SIZE: 6.875” L (174.63mm) x 1.875” H (47.63mm) x 2” W (51mm)
 MATERIAL: BLACK ANODIZED ALUMINUM AND ABS PLASTIC
 WIRING INTERFACE: 14 PIN CONNECTOR WITH 4 FEET OF CABLE
 CERTIFICATIONS: UL/CUL 294/S319, FCC PART B
 THE SREX-100 HAS A THREE YEAR WARRANTY

PAGE 6PAGE 1

The SREX-100 is an active infrared request to exit sensor for interior applications located
within the protected premise. It is U.L. listed as a request to exit device under the U.L.
UL294 and the CAN/ULC-S319 standard. The SREX-100 is rated a “class 1” as per the CAN/
ULC-S319 standard. The SREX-100 is designed to mount over the door header so that its de­tection pattern is placed directly over the door handle. When the user reaches for the door
handle the exit device releases allowing the person to exit. The active detection curtain is well
defined to keep the door secure while rejecting parallel traffic and objects placed under it.

TYPICAL INSTALLATION WIRING

B
R

O

W

N

/

W

H

I
T
E

B
R

O

W

N

O
R

A
N
G

E

/
W
H

I
T
E

O
R
A
N
G
E

B
L
U
E

/

W

H

I

T
E

B
L
U
E

W

H

I
T
E

C

O
M

B

G
R
E
E
N

N

/

O

B

Y
E
L
L
O

W

N

/

C

B

W

H

I
T
E

/
B
L
A
C
K

C

O
M

A

Y
E
L
L
O

W

/
B
L
A
C
K

N

/
C

A

G
R
E
E
N

/
B
L
A
C
K

N

/
O

A

B
L
A
C
K

P

W

R

R
E
D

P

W

R

12 OR 24 VDC

I.T.E.

MODEL

AMS4-240100FU

U.L. LISTED

POWER SUPPLY

FILE NUMBER

E141650

+

N/C DOOR

POSITION

SWITCH

MODEL

KP-100

DIP SW. 2

MUST BE

ON WHEN

DOOR

POSITION

SWITCH

IS USED.

USE

COMMON

AND

NORMALLY

OPEN

CONTACTS

USE

COMMON

AND

NORMALLY

CLOSED

MOMENTARY

CONTACTS

TECHNICAL ASSISTANCE

IF TECHNICAL ASSISTANCE IS REQUIRED CALL 1 800 645-5538

MODEL TS-2

U.L. FILE
NUMBER

SA32686

ALARM CONTROLS

U.L. LISTED

MAGNETIC LOCKS

FILE NUMBER

R16759

NOTE:

FOR U.L. LISTED INSTALLATIONS THE SREX-100 SHOULD ONLY BE POWERED BY A U.L. 294
LISTED POWER SUPPLY, AS WELL AS CONNECTED TO A U.L. LISTED ELECTRICAL LOCKING
(EL) DEVICE. FOR CAN/ULC-S319 LISTED INSTALLATIONS THE SREX-100 SHOULD ONLY BE
POWERED BY A ULC--S319 LISTED POWER SUPPLY AS WELL AS CONNECTED TO A ULC­S319 LISTED ELECTRICAL LOCKING (EL) DEVICE, CARD READER/KEYPAD AND DOOR/REX
SWITCHES.

THE USE OF ANY ADD-ON, EXPANSION, MEMORY OR OTHER MODULE MANUFACTURED OR
SUPPLIED BY THE MANUFACTURER’S REPRESENTATIVE WILL INVALIDATE THE CAN/ULC­S319 CERTIFICATION.

WHEN USED WITH ELECTRIC STRIKES ON SUPERVISED PORTALS, REQUEST-TO-EXIT DE­VICES SHALL BY-PASS PORTAL ALERTS CAUSED BY EXITING. WHEN USED WITH ELECTRO­MAGNETIC LOCKS ON SUPERVISED PORTALS, REQUEST-TO-EXIT DEVICES SHALL SIGNAL
THE ACCESS CONTROL UNIT TO RELEASE THE ELECTROMAGNETIC LOCKS AS WELL AS
TO BYPASS PORTAL ALERTS CAUSED BY EXITING.

TERMINAL AND LEADS COMPLY WITH CSA, C22.1, CANADIAN ELECTRICAL CODE, PART I,
SAFETY STANDARD FOR ELECTRICAL INSTALLATIONS.

FOR U.L. 294 AND NFPA 101 SECTIONS 7.2.6.2.1 WIRE THE LOCKING DEVICE FOR FAIL-SAFE
OPERATION.

CAN/ULC-S319 LIMITS THE RATED OUTPUT OF THE AUDIBLE SIGNAL DEVICE, (STATED AS A
SOUND PRESSURE LEVEL), (SPL), FROM 70 dBA TO A MAXIMUM OF 100 dBA AT 1 METER.

UL-294 LIMITS THE RATED OUTPUT OF THE AUDIBLE SIGNAL TO A MINIMUM OF 85 dBA AT
10 FEET.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTER­FERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED THAT MAY
CAUSE UNDESIRED OPERATION.

NOTE: THE THREE INPUTS TO THE SREX-100 MUST BE USED AS A DRY INPUT WITH NO

VOLTAGE APPLIED FROM THE CARD READER, DOOR POSITION SWITCH OR THE
REQUEST TO EXIT STATION.

COMPLETING THE INSTALLATION

TROUBLE SHOOTING THE INSTALLATION

TYPICAL DOOR INSTALLATION

PAGE 2PAGE 5

SREX-100 INSTALLATION

PREPARING THE SREX-100 FOR MOUNTING

LED INDICATORS

BUZZER SOUNDS

SREX-100

CENTERED

ABOVE DOOR

HANDLE

DETECTION

CENTERED

ABOVE DOOR

HANDLE

SREX-100
HOUSING

LENS

MULTI-CONDUCTOR

CABLE

END CAP

RIGHT

GREEN Power ON and no detection.

RED Object in detection zone or input activated.

Hand in detection zone or request to exit input activated..

YELLOW Relay active

FLASHING When sensor is or any of the enabled inputs are in constant
YELLOW detection for more than 10 seconds sensor will return to normal

YELLOW

when viewing field is clear.

.

When DIP SW 5 is in the ON position the buzzer will be enabled.

BUZZER BEEPING Sensor is blocked for more than 10 seconds.

BUZZER ON STEADY DIP SW 2 is in timer mode, (Off). If the sensor is activated or

the REX input is closed or the card reader/keypad input is
used. DIP SW 2 is in relock mode, (ON). Door position

STEP 1. Make sure that the sensor releases the locking device.

NOTE: The SREX-100 and devices connected to it must be mounted inside

the protected area to be UL-294 and ULC-S319 compliant.

STEP 1. Remove the Phillips head screw holding the right end cap. Take off

the right end cap only.

STEP 2. Slide the lens out of the housing.

STEP 3. Slide the PCB with clips attached from the housing.

Do not remove clips.

STEP 4. Position the SREX-100 drill template on door frame or above door

frame over door handle.

STEP 5. A 5/16” diameter hole is required in door frame or mounting surface

to allow cable entry. This hole is located at the right side of the
housing thru the elongated hole.

STEP 6. Fasten the SREX-100 housing with the two TEC screws provided.

It may be necessary to drill a 1/8” pilot hole for ease of screw installa­tion.

CAUTION: ESD electrostatic discharge: The circuit board is vunerable to

damage by electrostatic discharge. Before handling PCB dissipate
your body’s charge.

STEP 2. Test the detection height of the sensor.

STEP 3.. Test the detection zone parallel to the door and in front of the door

handle.

STEP 4. Snap the PCB into the housing. The top of the PCB goes into the

housing first.

If the SREX-100 is detecting erratically the sensor beams are reflecting off the
handle. Adjust the angle of the sensor so the IR beams are in front of the handle.

After the SREX-100 has been wired and powered the sensor can now be adjusted to the
installation requirements.

DETECTION RANGE

The detection distance is adjusted by the RNG, (range), potentiometer located at the
upper left hand side of the PCB. The range is 20 to 48 inches.
Turning the potentiometer clockwise increases the range, turning the potentiometer coun­terclockwise decreases the range.

RELAY ON TIME

The relay on time is adjusted by the TIME potentiometer which is the center potentiome­ter located at the upper left hand side of the PCB. The relay on time range is 1/2 to 60
seconds. The Time potentiometer is non-linear with the first 10 seconds covered by the
first half of the potentiometer and 11 to 60 seconds covered by the second half of the
potentiometer. Turning the potentiometer clockwise increases the relay on time, turning
the poteniometer counterclockwise decreases the relay on time.

BUZZER VOLUME

The buzzer volume is controlled by the VOL potentiometer located at the upper right
hand side of the PCB. Turning the potentiometer clockwise increases the buzzer vol­ume, turning the potentiometer counterclockwise decreases the buzzer volume.

PAGE 4PAGE 3

CABLE COLOR CODE

ADJUSTMENT OF SENSOR FIELD

ADJUSTMENT OF SENSOR

DIP SWITCH SETTINGS

CABLE WIRE COLOR

FUNCTION

RED 12 OR 24 VAC/DC, AUTO SENSING

BLACK 12 OR 24 VAC/DC, AUTO SENSING

WHITE/BLACK STRIPE

COMMON CONTACT RELAY A

GREEN/BLACK STRIPE N/O CONTACT RELAY A

YELLOW/BLACK STRIPE N/C CONTACT RELAY A

WHITE COMMON CONTACT RELAY B

GREEN N/O CONTACT RELAY B

YELLOW N/C CONTACT RELAY B

BLUE CARD READER/KEYPAD INPUT

BLUE/WHITE STRIPE CARD READER/KEYPAD INPUT

ORANGE REQUEST TO EXIT N/O INPUT

ORANGE/WHITE STRIPE REQUEST TO EXIT N/O INPUT

BROWN N/C DOOR POSITION SWITCH

BROWN/WHITE STRIPE N/C DOOR POSITION SWITCH

NOTE: The SREX-100 contains a double pole-double throw relay and the two sets of

relay contacts are referred to as A and B.
The Card Reader/Keypad and the Door Position Switch are dry inputs.

The SREX-100 is factory pre-set at the five degree angle. If there is an obstruction in the
sensor field preventing a clear view of the door handle it will be necessary to change the
viewing angle. Un-plug the connector and slide the PCB from the housing with the clips
attached. Do not remove the clips from the PCB! Change the viewing angle to the zero
degree angle. It is recommended that the sensor be powered and both hand and walk
tested. If the sensor is detecting erratically, the IR beams may be reflecting off the door
handle and the viewing angle should be adjusted outward. Slide the PCB back into the
housing and leave the right end cap off until all final adjustments have been made.

ZERO DEGREES

FIVE DEGREES

TEN DEGREES

DO NOT

CHANGE

THIS SIDE

DO NOT

CHANGE

THIS SIDE

DO NOT

CHANGE

THIS SIDE

NOTCH

# 1

NOTCH

# 2

NOTCH

# 3

SWITCH 1 ON FAIL-SAFE MODE

SWITCH 1 OFF FAIL-SECURE MODE

When the SREX-100 is in constant dectection, more than 10 seconds, It will go into a
fail-safe or fail-secure mode depending upon the switch setting.

SWITCH 2 ON RELOCK MODE, DOOR POSITION
When a normally-closed door contact is installed the door will relock after the door is
opened and then closed.

SWITCH 2 OFF TIMER MODE
The door will relock after the preset relay on time.

SWITCH 3 ON DOOR POSITION RELOCK TIME IS A FIXED 10 SECONDS

SWITCH 3 OFF DOOR POSITION RELOCK TIME IS A FIXED 30 SECONDS

SWITCH 4 ON DOOR UNLOCK TIMER

If switch 2 is in the off position,(timer mode), then door will remain unlocked as long as
there is activity in the detection range. If there is no activity then the timer will restart and
relock the door after the preset time.

SWITCH 5 ON BUZZER ENABLED, THE BUZZER IS NOT INTENDED TO BE A

SWITCH 5 OFF BUZZER DISABLED

SWITCH 6 ON CARD READER OR KEYPAD INPUT IS ENABLED

SWITCH 6 OFF CARD READER OR KEYPAD INPUT IS DISABLED

SWITCH 7 ON BUZZER SOUNDS WHEN N/C CARD READER INPUT IS OPEN

SWITCH 7 OFF BUZZER DOES NOT SOUND WHEN N/C CARD READER INPUT IS

CLOSED

BURGLARY ALARM