This manual is the latest at the time of printing, and does not
include the modification which may be made after the printing,
by the constant improvement of product.
I. Safety Instructions
ˋ
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “ dangerous
voltage” within the product’ s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY.
PRECAUTIONS DURING SERVICING
1. In addition to safety, other parts and assemblies are
specified for conformance with such regulations as
those applying to spurious radiation. These must
also be replaced only with specified replacements.
Examples: RF converters, tuner units, antenna
selection switches, RF cables, noise-blocking
capacitors, noise-blocking filters, etc.
2. Use specified internal Wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
3. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulating Tape
2) PVC tubing
3) Spacers (insulating barriers)
4) Insulating sheets for transistors
5) Plastic screws for fixing micro switches
4. When replacing AC primary side components
(transformers, power cords, noise blocking
capacitors, etc.), wrap ends of wires securely about
the terminals before soldering.
5. Make sure that wires do not contact heat generating
parts (heat sinks, oxide metal film resistors, fusible
resistors, etc.)
6. Check if replaced wires do not contact sharply edged
or pointed parts.
7. Make sure that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
MAKE YOUR CONTRIBUTION TO PROTECT THE
ENVIRONMENT
Used batteries with the ISO symbol
for recycling as well as small
accumulators (rechargeable batteries), mini-batteries
(cells) and starter batteries should not be thrown
into the garbage can.
Please leave them at an appropriate depot.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(s erv ici ng) in str uct io ns in the li ter atu re
accompanying the appliance.
WARNING:
Before servicing this TV receiver, read the X-RAY
RADIATION PRECAUTION, SAFETY INSTRUCTION
and PRODUCT SAFETY NOTICE.
X-RAY RADIATION PRECAUTION
1. Excessively high can produce potentially hazardous
X-RAY RADIATION. To avoid such hazards, the high
voltage must not exceed the specified limit. The
normal value of the high voltage of this TV receiver
is 27 KV at zero bean current (minimum brightness).
The high voltage must not exceed 30 KV under any
circumstances. Each time when a receiver requires
servicing, the high voltage should be checked. The
reading of the high voltage is recommended to be
recorded as a part of the service record, It is
important to use an accurate and reliable high
voltage meter.
2. The only source of X-RAY RADIATION in this TV
receiver is the picture tube. For continued X-RAY
RADIATION protection, the replacement tube must be
exactly the same type as specified in the parts list.
3. Some parts in this TV receiver have special safety
related characteristics for X-RADIATION protection.
For continued safety, the parts replacement should
be under taken only after referring the PRODUCT
SAFETY NOTICE.
SAFETY INSTRUCTION
The service should not be attempted by anyone
unfamiliar with the necessary instructions on this TV
receiver. The following are the necessary instructions
to be observed before servicing.
1. An isolation transformer should be connected in the
power line between the receiver and the AC line
when a service is performed on the primary of the
converter transformer of the set.
2. Comply with all caution and safety related provided
on the back of the cabinet, inside the cabinet, on the
chassis or picture tube.
3. To avoid a shock hazard, always discharge the
picture tube's anode to the chassis ground before
removing the anode cap.
-2-
4. Completely discharge the high potential voltage of the
ˋ
picture tube before handling. The picture tube is a
vacuum and if broken, the glass will explode.
5. When replacing a MAIN PCB in the cabinet, always
be certain that all protective are installed properly
such as control knobs, adjustment covers or shields,
barriers, isolation resistor networks etc.
6. When servicing is required, observe the original lead
dressing. Extra precaution should be given to assure
correct lead dressing in the high voltage area.
7. Keep wires away from high voltage or high tempera
ture components.
8. Before returning the set to the customer, always
perform an AC leakage current check on the exposed
metallic parts of the cabinet, such as antennas,
terminals, screwheads, metal overlay, control shafts,
etc., to be sure the set is safe to operate without
danger of electrical shock. Plug the AC line cord
directly to the AC outlet (do not use a line isolation
transformer during this check). Use an AC voltmeter
having 5K ohms volt sensitivity or more in the
following manner.
Connect a 1.5K ohm 10 watt resistor paralleled by a
0.15µF AC type capacitor, between a good earth
ground (water pipe, conductor etc.,) and the exposed
metallic parts, one at a time.
Measure the AC voltage across the combination of
the 1.5K ohm resistor and 0.15 uF capacitor. Reverse
the AC plug at the AC outlet and repeat the AC
voltage measurements for each exposed metallic
part.
The measured voltage must not exceed 0.3V RMS.
This corresponds to 0.5mA AC. Any value exceeding
this limit constitutes a potential shock hazard and
must be corrected immediately.
The resistance measurement should be done
between accessible exposed metal parts and power
cord plug prongs with the power switch "ON". The
resistance should be more than 6M ohms.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this TV
receiver have special safety-related characteristics.
These characteristics are offer passed unnoticed by
visual spection and the protection afforded by them
cannot necessarily be obtained by using replacement
components rates for a higher voltage, wattage, etc.
The replacement parts which have these special
safety characteristics are identified by marks on
the schematic diagram and on the parts list.
Before replacing any of these components, read the
parts list in this manual carefully. The use of
substitute replacement parts which do not have the
same safety characteristics as specified in the parts
list may create shock, fire, X-RAY RADIATION or
other hazards.
Good earth ground
such as the water
pipe, conductor,
etc.
AC Leakage Current Check
AC VOLTMETER
Place this probe
on e a c h e xposed met al li c
part
-3-
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
ˋ
Reference No : LCT3201TD
Product Specification
1.1 VIDEO SECTION
Display size 32”/16:9
Display Resolution 1366 X 768
Pixel Pitch
Peak Brightness 550(nits)
Contract Ratio 1000:1, Typical (1/100 White Window, Dark Room)
View Angle Hor. And Vert. ≥170 degree
Color Deeps 16.7M Color (R / G/ B each 256 Scales)
PC Resolution Supporting VGA, SVGA, XGA,WXGA
HDTV Compatible 480p / 720p / 1080i
Progressive Scanning Yes
Film Mode Pull Down Yes
“GAMMA” Correction Yes
Color Temperature Control Yes
Comb Filter Yes
Second De-interlace for Sub picture No
Wide Mode
TV System NTSC M
Dual Tuner System No
AV Input Color System PAL /NTSC
PIP Basic mode (video on graphic mode,resolution≥1024×768)
1.2 AUDIO SECTION
CHIMEI V320B1-L01
MK8205
USA
0.17025mm×0.51075mm
Normal, Full, Wide 1, Wide 2, Wide 3, 4:3, No scale and
Panoramic.
Audio Output Power 6W×2 Max.(8 ohm)
Sound Effect Spatial Effect and Surround
Tone Control Yes
Power Rating AC 100-240V, 50/60Hz
Power Consumption 220W
1.6 Support the Signal Mode
This machine can support the different from VGA signal mode in 7 kinds
1.7 HDTV Mode (YPbPr)
MTS with SAP
Horizontal
Resolution
640 x 480
800 x 600
1024 x 76848.4060.00
Frequency
(kHz)
31.5060.00
37.8672.81
35.16
37.90
46.90
48.0872.19
Vertical
Frequency
(Hz)
56.25
60.32
75.00
Horizontal
Resolution
480i15.73459.94
480p(720x480)31.46859.94
720p(1280x720)45.0060.00
1080i(1920x1080)33.7560.00
Frequency
(KHz)
Vertical
Frequency
(Hz)
1.8 Remote Control
ˋ
Power ( ): Press to turn on and off.
Mute ( ): Press to mute the sound.
Press again or press , to restore
the sound.
CCD: Press to select the Closed
Caption mode.
V-CHIP: Press to select the child
protect mode.
MTS: Press repeatedly to cycle through
the Multi-channel TV sound (MTS)
options: Mono, Stereo and SAP
(Second Audio Program).
Favorite: Press repeatedly to cycle through the favorite channel list.
PIP. Pos: Press to change the PIP window position under PIP mode.
PIP. Size: Press to cycle through the PIP size, such as Large, Medium,
Small.
Add/Erase: Press to add or delete favorite channel.
PIP: Press to cycles through the
different POP or PIP modes, such as
Basic PIP, LR POP, and exit.
0~9 Number Buttons: In TV mode, press 0~9 to
channel changes
In DVD mode, press 0~9 to input the
items.
Zoom: Press to zoom the image max
from 8 times to minimally 1/8 times.
Recall: Press to return to previous channel.
select a channel; the
after 2 seconds.
P.Mode: Press repeatedly to cycle
through the picture mode: Hi-Bright, User, Dark, Normal and Vivid.
P.Size: Press repeatedly to cycle through the picture size that best corresponds your viewing requirements: Normal, Full, Wide1, Wide2, Wide3, 4:3, No scale, Panoramic
and Normal.
When in POP mode, it can select picture size is: Full, 4:3 and Normal.
Vol / : Press to adjust the volume.
Ch
and hold down either channels.
Freeze: Press to freeze the picture, press again to restore the picture.
/ : Press to scan through channels.
To scan quickly through channels, press
(Continued on next page)
Menu: Press to enter into the on-screen
ˋ
setup menu, press again to exit.
S.Mode: Press repeatedly to cycle through the sound mode: Normal,
News, Cinema, Flat and User.
, , , , Enter: Press , , ,
to move the on-screen cursor. To
select an item, press ENTER to
confirm. And it can also press
to scan through channels, press
or to adjust the volume excepting
DVD mode.
System: Press repeatedly to cycle through the system options: AUTO
and NTSC3.58.
(This button is inactive for TV, VGA,
COMPONENT input source.)
or
Source: Press to select the signal
source, such as TV, AV, S-Video,
Component, DVD or VGA.
Sleep: Press repeatedly until it
displays the time in minutes (5 Min,
10 Min, 15 Min, 30 Min, 60 Min, 90
Min, 120 Min and, OFF) that you
want the TV to remain on before
shutting off. To cancel sleep time,
press
until sleep OFF appears.
Display: Press to display the channel information and it disappear after 3
seconds.
Play/Pause: Press to play or pause the DVD disc.
Stop: Press to stop playing the disc.
Angle: Press to select desired viewing
angle of the Video (disc feature).
Open/Close: Press to open or close the disc tray.
Skip+/-: Press to skip the forward or backward.
Search+/- : Press to search the forward or backward.
DVD Menu: Press to return DVD disc menu.
Sleep button repeatedly
(Continued on next page)
DVD Info: Press to display DVD
ˋ
information.
Setup: Press to display a menu. Press it again to exit menu.
Repeat: Press repeatedly to cycle through the options: CHAPTER,
TITLE, ALL and nothing.
Audio: Press to select desired audio
track.
Prog: Press to display the program
menu. Press it again to exit.
Sub. title: Press to select desired
DVD subtitle.
Title: Press to display to DVD disc
title.
Note: Press
control can turn on TV set from
last preview mode.
l.
Ch
/ on the remote
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
ˋ
Reference No : LCT32ADTD
Technical Data
TV AC 100-240, 50/ 60Hz 1. Power supply
3. Receiving channels
Remote control
RF input NTSC M 2. TV system
Video input PAL/NTSC 3.58
TV
19. Cell Defect Subject to Panel supplier specification
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
ˋ
Reference No : LCT3201TD
Attachment 1:Electrical & Optical Specification
No. Items Instruction TypicalLimit Unit
1 Video sensitivity For 30dB S/N 44 ≤51 dBuV
2 FM sound sensitivity For 30dB S/N 21 ≤35 dBuV
3 Color sensitivity For RF transmission 37 ≤40 dBuV
4 CCD sensitivity
5 Minimum NICAM threshold Without crackline noise N/A N/A dBuV
6 Stereo Channel Separation BTSC. 18 ≥15 dB
TV screen refreshes 40 times
number of mistakes≤8
43 ≤50 dBuV
AGC static characteristic
7
8 Selectivity Adjacent sound carrier 30 ≥28
Below adjacent sound carrier30 ≥30 dB
Adjacent picture carrier 45 ≥40
Up adjacent picture carrier 40 ≥30
9 IF rejection 55 ≥45 dB
10 Image rejection VHF 57 ≥45 dB
UHF 55 ≥40
11 AFT pull-in range ±1.0 ≥⏐±1.0⏐ MHz
12 Chroma sync pull-in range ±500 ≥⏐±200⏐ Hz
13 Color killer function -11 ≤-10 dB
14 Resolution
Video
Accept. Picture/Sound repr.90
RF
Vertical
Horizontal
Vertical 400 ≥400 Lines
PAL 300 ≥300 Lines Horizontal
NTSC 260 ≥240 Lines
PAL 410 ≥400 Lines
NTSC 320 ≥300 Lines
450 ≥450 Lines
≥90
dBuV
White
Coordination
16 View
Angle(Lo/3)
17 Overscan Cross hatch signal 96 94~98 %
Horizontal
Vertical
XW 0.295 0.295±0.02 15 Color
Y
W
Full Pattern
0.300 0.300±0.02
170
≥170
Degree
18 Picture position In all direction ±2 ≤⏐±3⏐ mm
19 H sync pull-in range ±400 ≥⏐±200⏐ Hz
20 V sync pull-in range 6 ≥6 Hz
21 Audio frequency response ±3dB ref. to 1KHz 0.15~12 0.2~12 KHz
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
ˋ
Reference No : LCT3201TD
22
Max Audio Output Power 7×2 ≥5.0×2 W
23 Audio output power
10% THD
24 THD Po=0.5W 0.5 ≤3 %
25 Signal to buzz ratio coeighting 50 ≥30 dB
26 Minimum volume hum coeighting 6 ≤10 mVrms
Operating 200 ≤200 W 38 Power consumpution
Stand by 3 ≤5 W
5m
The distance between
the tester and the
LCD-TV set is four
times as many as the
screen height
20 ≥15 Degree
No obvious vibration noise can be
heard
KAWA ELECTRONIC RESEARCH & DEVELOPMENT CENTRE
ˋ
Reference No : LCT3201TD
Test Condition
All tests shall be performed under the following conditions unless otherwise specified
1 Picture Modulation 87.5%
2 Sound Modulation
3 Picture to Sound Ratio 10dB
4 Sound Artificial Load
Resistor
Video signal
5
6 Audio signal 1KHz sine wave 0.5Vrms
7 Other conditions:
A. Switch LCD-TV on and let it warm up for more than 30 minutes.
Viewing distance: 3H (H: Panel High) in front of LCD, about 2M.
Ambient light: ≤0.1 cd/ m
B. Brightness, Contrast, Saturation, Tint, sharpness set at normal.
C. Connect RMS volt meter to speaker terminals and adjust the LCD volume to get 500mW RMS
power at each terminals.
D. With image sticking protection of LCD module. The luminance will descend by time on a same
still screen and rapidly go down in 5 minutes, when measuring the color tracking and luminance
of a same still screen, be sure to accomplish the measurement in one minute to ensure its
accuracy.
E. Due to the structure of LCD module. The extra-high-bright same screen should not hold over 5
minutes for fear of branding on the panel.
F. RF test point: Video output.
27KHz Dev. For DK/I/BG
15KHz Dev. For M/N
8 ohm
Stair and Special
2
8 Note:
*(1) Now this project cannot fit the limited spec. the typical audio input level is 1.0 Vrms,
*(2) The audio out level is controlled by the volume level, the range is from 0 to 0.5Vrms.
DVD player's spec. For LCD-TV Combo
e
t
ˋ
DivisionSectionRemarks
nameAKAI
Marketing Area( setup default language)
General
DVD Module
PlaybackPlayable Media TypePlayable Disc Type: DVD, CD,
Disc TypePlayable Disc TypeDVD(Single/ Dual layer, Double sided), CD
VideoVideo output signalNTSC
AudioAudio DAC
Playback Fast forward/backwardx2,x4,x8,x16,x32
FeaturesSlow motion forwardx1/2,x1/4,x1/8,x1/16
Display Graphical user interfac
user OSD Language3 (ENG is base ,SPA and French)
operationSubtitlePresent
Front Panel VFD/ LEDx
Rear PanelComposite Video outputx
Power supply+5v,+3.3v
Power Consumption15W
Manufactruer of Loader mechanismForyou DL06-LS
Opitical Pick UP
Chipset usedMTK 1389FE
Disc Size8cm/12cm
Regional code
NTSC/ PAL Disc playbackO/O
Video DAC27MHz/ 10bit
Dynamic range Present
Dolby digital decoderPresent
DTS decoderoptional
SRS + TruSurround for 2 channel Not present
3D Virtual surround for 2 channel Not present
Slow motion backwardoptional
Still picturePresent
Frame by frame forward/reverseForward only (Step function)
Skip forward/reversePresent
Repeat function Present
DVD closed caption Present
Transition Effect for picture CDNot present
Rotation of picture for picture CDsPresent
Last MemoryPresent
Screen saverPresent
Resume playPresent
Program functionPresent
PBC ON/OFFDefault on PCB
Parental lockPassward : 0000
Picture mode selector16:9, 4:3 LB, 4:3 PS(4:3 PS as default)
Intro scanNot present
Digest in VCDPresent, only for PIC CD
Time searchPresent
Multi anglePresent
Selectable audio language streamsPresent
kalaoke functionx