AKAI APC40 Quick Start Guide

QUICKSTART GUIDE
GUÍA DE INICIO RÁPIDO
GUIDE D'UTILISATION RAPIDE
KURZANLEITUNG
ENGLISH ( 1 – 3 )
FRANÇAIS ( 7 – 9 )
DEUTSCH ( 10 – 12 )
GUIDA RAPIDA
ITALIANO ( 13 – 15 )
WWW.AKAIPRO.COM
WWW.ABLETON.COM

INTRODUCTION

This Quickstart Guide is intended to give you a brief overview of the functionality and features of the Akai APC40 Ableton Controller.
APC40 is designed for performance with Ableton Live. In this manual, you will find instructions on how to connect the APC40 and use its basic features with Ableton Live – Akai Professional APC Edition. APC40 can also be used in "generic mode" as a controller with other virtual DJ applications that use MIDI protocol.
If you already own Ableton Live, make sure to download the latest Ableton Live update for full APC40 support at www.ableton.com/latest_versions. We recommend referring to the Ableton manual on the CD as well as the lessons available in the software itself.

SOFTWARE INSTALLATION

To install the Akai Profesisonal APC Edition of Ableton Live, simply insert the included CD into your computer, then follow the on-screen instructions.
To access the software after installing it, you can find it here:
PC: Start Menu All Programs Ableton Live [Version Number] Mac: Applications Ableton Live [Version Number].
In order for Ableton Live to properly recognize the APC40, however, you must connect the controller before opening the software, and you must set your Preferences accordingly. See the CONNECTION DIAGRAM and SOFTWARE SETUP sections for instructions on how to do this.

CONNECTION DIAGRAM

1. Connect APC40 to a power source using the included 12V–2A DC power adapter.
2. Connect APC40 to your computer with a standard USB cable (included).
3. Connect any pedals you may want to use to the appropriate footswitch (FS) jacks.
4. Turn on APC40.
5. Open Ableton Live – Akai Professional APC Edition.
Note: We recommend keeping the APC40 away from devices that can cause electrical interference. If its performance is noticeably affected, move or reposition the APC40 away from the source of interference.

SOFTWARE SETUP

After connecting the APC40 (as shown in the CONNECTION DIAGRAM), you will need to configure Ableton Live to recognize it:
1. Open Ableton Live – Akai Professional APC Edition (after connecting and powering on the APC40).
2. Go to Options Preferences (PC) or Live Preferences (Mac).
3. Click the MIDI Sync tab.
4. Select "APC40" as the device for the "Control Surface," "Input" and "Output."
5. Under "MIDI Ports," turn all available "Track" and "Remote" settings "On."
6. Close the Preferences window.
When you open the software, a panel on the right should display Lessons to help you get started with the Akai Professional APC Edition of Ableton Live. We recommend starting with the “Tour of Live” Lesson. From the first page of this Lesson, there is also a link to a special Lesson called “Using the APC40,” which will walk you through all of the APC40’s controls in detail.
We recommend referring to the Lessons to further acquaint yourself with the hardware's and software's features so you can take full advantage of them when performing! (If you decide to close this panel for now, you can always access them again from the Help menu.)
Note on MIDI Mapping: We have already mapped APC40's controls to some of Ableton Live's most useful functions, but if you would like to change your MIDI mappings, you can do so by clicking the "MIDI" button in the upper right-hand corner of the software window. From here you can create new mappings as you could with any other controller. Refer to Ableton Live's manual or lessons for more information on how to do this.
1

TOP PANEL OVERVIEW

6
1
4
7
3
18
19
18
17
2
5
8
10
11
12
13
14
9
15 15 15
16
1. CLIP LAUNCH / SESSION OVERVIEW – While in Clip Launch
View (the default), this 8x5 grid of buttons is used to launch clips in Ableton Live. The 8 vertical columns represent 8 tracks in the software while the 5 horizontal rows represent 5 clip slots in each track. In this view, the button LED colors represent the following:
OFF – empty AMBER – clip present, not playing GREEN – clip present, playing RED – clip present, recording
When the SHIFT button is held, this grid will change to Session Overview. In this view, each button represents an entire 8x5 grid of clip slots in the software (that is, each button represents a different Clip Launch View). Selecting one will change the Clip Launch View. This allows you to access and use more than the 5 rows and 8 tracks represented by just one Clip Launch View. While in Session Overview, the button LED colors represent the following:
OFF – no clips are present in this 8x5 grid AMBER – clips are present in this 8x5 grid, which is currently
selected GREEN – clips are present in this 8x5 grid, which contains clip
slots that are currently playing RED – clip are present in this 8x5 grid, but no clip slots are currently playing
Examples: If you have 16 tracks with 20 clips in each track, the "first" Clip Launch View will represent Clips 1-5 of Tracks 1-8.
If you hold SHIFT and press the second button in the first row, after releasing SHIFT the Clip Launch View will represent Clips 1-5 of Tracks 9-16.
If you hold SHIFT and press the first button in the second row, after releasing SHIFT the Clip Launch View will represent Clips 6-10 of Tracks 1-8.
Note: In the software, a red rectangle around an 8x5 grid of clips represents APC40's current Clip Launch View. You can change/shift the Clip Launch View with APC40's controls (e.g. in the Session Overview).
Note: If the current Clip Launch View is "between" two 8x5 grids in the software, both buttons representing those two grids will light.
2
2. SHIFT – Holding this button down lets you access extra controller features (printed in red on the control
surface), such as Session Overview or another bank available in the DEVICE CONTROL section.
3. SCENE LAUNCH – These buttons triggers an entire row of clips, called a "scene." All clips in that
scene will be triggered, including those not represented in that Clip Launch View.
4. CLIP STOP – These buttons stops all clips playing in the corresponding track, including those not
represented in that Clip Launch View.
5. STOP ALL CLIPS – This button stops all clips playing when they reach the end. (This differs from the
STOP button, which stops playback immediately.)
6. TRACK CONTROL – These knobs represent the PAN and SEND1-3 level of the current 8 tracks.
Select PAN, SEND1, SEND2 or SEND3 by pressing the corresponding button underneath.
7. TRACK SELECTION – Selects which track is being controlled in the DEVICE CONTROL section.
Tracks 1-8 and Master can be selected.
8. DEVICE CONTROL – These 8 knobs control 8 parameters of the currently selected device. 8 banks of
controllers are available for a total of 64 controls. To access the additional banks, hold the SHIFT button down while pressing one of the buttons underneath (numbered 1-8).
9. ABLETON LIVE COMMAND CONTROLS – These controls specific functions in Ableton Live:
CLIP / TRACK – Toggles between Clip View and Track View. DEVICE ON / OFF – Turns the currently selected device on or off.
Å – Selects the previous device on a track. Æ – Selects the next device on a track.
DETAIL VIEW – Turns Detail View on or off. REC QUANTIZATION – Turns Record Quantization on or off. MIDI OVERDUB – Turns MIDI Overdub on or off. METRONOME – Turns the metronome on or off.
10. TRACK ACTIVATORS – When lit, the current corresponding track is active. Pressing a button will
mute it (the button will become unlit). Press it again to activate it.
11. SOLO / CUE – Solos the selected track, sending it to the Cue Output. Press it again to un-solo it.
12. RECORD ARM – Arms the selected track for recording. Press it again to disarm it.
13. VOLUME FADERS – Adjusts the volume for the corresponding track or Master.
14. CUE LEVEL – Controls the volume sent to the Cue Output and the volume of sample auditioning.
15. TRANSPORT CONTROLS – These transport controls – PLAY, STOP, and REC – represent the same
functions in the software.
16. CROSSFADER – Crossfades between Crossfader Assignments A and B in the software.
17. BANK SELECT – These pads move the cursor/selection in
Ableton Live by one track (left or right) or by one scene (up or down). Holding SHIFT while pressing this pad will move the selection by 8 tracks (left or right) or by 5 scenes (up or down), effectively changing the Clip Launch View (see #1).
18. NUDGE +/- – These buttons are the same as the Nudge +/-
Note: In the software, a red rectangle around an 8x5 grid of clips represents APC40's current Clip Launch View. You can change/shift the Clip Launch View with APC40's controls (e.g. SHIFT + BANK
SELECT).
buttons in the software, which slightly shift the tempo up or down for beat-matching.
19. TAP TEMPO – This button is the same as the Tap Tempo button in the software, which lets you
manually tap in a tempo for the track.

REAR PANEL OVERVIEW

1. DC POWER ADAPTER INPUT – Plug in the included 12V–2A DC power adapter here.
2. POWER ADAPTER RESTRAINT – You can secure a power adapter cord to this restraint to prevent accidental unplugging.
3. POWER ON / OFF – Turns the APC40 on or off.
4. USB CONNECTION – Plug a standard USB cable into this outlet and into the USB port of your computer. This connection is used to send and receive MIDI data to and from your computer.
5. FOOTSWITCH (FS) INPUTS 1 & 2 – You may connect optional 1/4" TS footswitches, such as a
standard keyboard sustain pedal, to these inputs. Be sure the footswitch is in the "off" position when connecting it to ensure its polarity is correct.
314255
3

INTRODUCCIÓN

Esta Guía de inicio rápido tiene la finalidad de darle una breve descripción general de la funcionalidad y las características del controlador de Ableton Akai APC40.
El APC40 está diseñado para realizar sesiones con Ableton Live. En este manual, encontrará instrucciones para conectar el APC40 y usar sus características básicas con Ableton Live – Akai Professional APC Edition. El APC40 se puede usar también
en “modo genérico” como controlador con otras aplicaciones de DJ virtual que usan el protocolo MIDI.
Si usted ya tiene Ableton Live, debe instalar la edición especial Akai Professional APC que está en el CD de software incluido para aprovechar plenamente las ventajas de la funcionalidad del controlador con el software. Recomendamos consultar el
manual de Ableton incluido en el CD, así como las lecciones disponibles en el software mismo.

INSTALACIÓN DEL SOFTWARE

Para instalar la edición Akai Professional APC de Ableton Live, inserte simplemente el CD incluido en su computadora y siga
las instrucciones de la pantalla.
Para acceder al software después de instalarlo, puede hallarlo aquí:
PC: Menú Start All Programs Ableton Live [Número de versión] (Menú Inicio > Todos los programas >
Ableton > Live [Número de versión]) Mac: Applications Ableton Live [Número de versión].
A fin de que Ableton Live reconozca correctamente al APC40, no obstante, debe conectar el controlador antes de abrir el software y configurar las preferencias en consecuencia. Consulte en las secciones DIAGRAMA DE CONEXIÓN y
CONFIGURACIÓN DEL SOFTWARE las instrucciones para hacerlo.

DIAGRAMA DE CONEXIÓN

1. Conecte el APC40 al suministro eléctrico con el adaptador de
potencia de 12 V–2 A CC incluido.
2. Conecte el APC40 a su computadora con un cable USB estándar (incluido).
3. Conecte los pedales que desea usar a los conectores de interruptores de pedal (FS) apropiados.
4. Encienda el APC40.
5. Abra Ableton Live – Akai Professional APC Edition.

CONFIGURACIÓN DEL SOFTWARE

Después de conectar el APC40 (como se muestra en el DIAGRAMA DE CONEXIÓN), es necesario que configure Ableton Live para reconocerlo:
1. Abra Ableton Live – Akai Professional APC Edition (después de conectar y alimentar el APC40).
2. Vaya a Options Preferences (Opciones > Preferencias) (PC) o Live Preferences (Mac).
3. Haga clic en la pestaña MIDI Sync (Sincronismo MIDI).
4. Seleccione "APC40" como dispositivo para "Control Surface" (Superficie de control), "Input" (Entrada) y "Output" (Salida).
5. Bajo "MIDI Ports" (Puertos MIDI), active todos los parámetros "Track" (Pista) y "Remote" (Remoto) disponibles.
6. Cierre la ventana Preferences (Preferencias).
Cuando abre el software, un panel de la derecha debe mostrar información acerca de las lecciones de uso del APC40 con la edición Akai Professional APC de Ableton Live. Recomendamos consultar estas lecciones para conocer mejor las características del hardware y el software a fin de aprovechar plenamente las ventajas de las mismas durante la sesión. (Si
decide cerrar este panel por ahora, siempre puede acceder al mismo desde el menú Help (Ayuda)).
Nota sobre las correlaciones MIDI: Ya hemos correlacionado los controles del APC40 con algunas de las funciones más útiles de Ableton Live, pero si desea cambiar sus correlaciones MIDI, puede llevarlo a cabo haciendo clic en el botón "MIDI" de la esquina superior derecha de la ventana del software. Desde aquí puede crear nuevas correlaciones como con cualquier otro controlador. Consulte el manual o las lecciones de Ableton Live para obtener información adicional sobre cómo hacerlo.
4
Loading...
+ 14 hidden pages