Page 1
XR-EM60
K(S)
XR-EM61
EZ(S)
SERVICE MANUAL
CD STEREO SYSTEM
SYSTEM
• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
(S/M Code No. 09-022-456-0T1).
CD
RECEIVER
CX–LEM60XR–EM60
CX–LEM61XR–EM61
BASIC CD MECHANISM : 3ZG-3 E13NM
SPEAKER
SX–LEM60
REMOTE
CONTROLLER
RC–CAS04
S/M Code No. 09-025-456-0R1
REVISION
DATA
Page 2
TABLE OF CONTENTS
SPECIFICATIONS ...............................................................................................................................................................3
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING .......................................................................4
PRECAUTION TO REPLACE OPTICAL BLOCK.............................................................................................................4
ELECTRICAL PARTS LIST (CX – LEM60 / CX – LEM61) ........................................................................................5 ~ 14
ELECTRICAL PARTS LIST (CZA – 3) ....................................................................................................................15 ~ 18
ELECTRICAL PARTS LIST (3ZG – 3).............................................................................................................................19
ELECTRICAL PARTS LIST (3ZG – 2).............................................................................................................................20
CHIP RESISTOR PART CODE.......................................................................................................................................21
TRANSISTOR ILLUSTRATION.........................................................................................................................................21
WIRING – 1 (MAIN)...........................................................................................................................................................22
SCHEMATIC DIAGRAM – 1 (MAIN : 1 / 3 / HP)...............................................................................................................23
SCHEMATIC DIAGRAM – 2 (MAIN : 2 / 3 <CD SECTION> / CD – DRIVE / CD – LOAD)..............................................24
SCHEMATIC DIAGRAM – 3 (MAIN : 3 / 3 <MICON SECTION>)....................................................................................25
WIRING – 2 (FRONT / KEY / HP) .....................................................................................................................................26
SCHEMATIC DIAGRAM – 4 (FRONT / KEY)...................................................................................................................27
WIRING – 3 (AMP)............................................................................................................................................................28
SCHEMATIC DIAGRAM – 5 (AMP) .................................................................................................................................29
WIRING – 4 (PT) ...............................................................................................................................................................30
SCHEMATIC DIAGRAM – 6 (PT).....................................................................................................................................31
WIRING – 5 (TUNER) .......................................................................................................................................................32
SCHEMATIC DIAGRAM – 7 (TUNER) .............................................................................................................................33
WIRING – 6 (CD – DRIVE / CD – LOAD) ..........................................................................................................................34
FL (HNA – 10SM19) GRID ASSIGNMENT / ANODE CONNECTION / PIN CONNECTION)..........................................35
IC BLOCK DIAGRAM...............................................................................................................................................36 ~ 37
IC DESCRIPTION .....................................................................................................................................................38 ~ 42
ADJUSTMENT (TUNER / MAIN)...............................................................................................................................43 ~ 47
CD TEST MODE ..............................................................................................................................................................48
MECHANICAL EXPLODED VIEW ...................................................................................................................................49
MECHANICAL PARTS LIST ............................................................................................................................................50
COLOR NAME TABLE .....................................................................................................................................................51
CD MECHANISM EXPLODED VIEW 1 / 2 <3ZG – 3 E13NM> ....................................................................................52
CD MECHANISM PARTS LIST 1 / 2 <3ZG – 3 E13NM> .............................................................................................53
CD MECHANISM EXPLODED VIEW 2 / 2 <3ZG – 2 E3NM> ......................................................................................54
CD MECHANISM PARTS LIST 2 / 2 <3ZG – 2 E3NM> ...............................................................................................55
ACCESSORIES PARTS LIST ..........................................................................................................................................56
OTHER PARTS LIST (CX – LEM60 / CX – LEM61)........................................................................................................57
OTHER PARTS LIST (CZA – 3)......................................................................................................................................58
OTHER PARTS LIST (3ZG – 3) ...................................................................................................................................... 59
OTHER PARTS LIST (3ZG – 2) ...................................................................................................................................... 60
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE) ...........................................................61
SPEAKER PARTS LIST (SX – LEM60)...........................................................................................................................62
– 2 –
Page 3
SPECIFICATIONS
MAIN UNIT CX-LEM60 <K>, CX-LEM61 <EZ>
TUNER
FM tuning range 87.5 MHz to 108 MHz
FM usable sensitivity (IHF) 16.8 dBf
FM antenna terminal 75 ohms (unbalanced)
MW tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step)
MW usable sensitivity 350 µV/m
LW tuning range 144 kHz to 290 kHz
LW usable sensitivity 1400 µV/m
MW/LW antenna Loop antenna
AMPLIFIER
Power output Rated: 24 W + 24 W
(6 ohms, T.H.D. 1 %, 1 kHz/DIN 45500)
Reference: 30 W + 30 W
(6 ohms, T.H.D. 10 %, 1 kHz/DIN 45324)
<EZ ONLY>
DIN MUSIC POWER: 57 W + 57 W
Input LINE IN: 500 mV
Outputs SPEAKERS: 6 ohms or more
PHONES: 32 ohms or more
DIGITAL OUT (OPTICAL) jack
CD PLAYER
Laser Semiconductor laser (l = 780 nm)
D/A converter 1 bit dual
Signal-to-noise ratio 85 dB (1 kHz, 0 dB)
Wow and flutter Unmeasurable
GENERAL
Power requirements 230 V AC, 50 Hz
Power consumption 59 W
Power consumption in standby mode
With ECO mode on: 0.6 W
With ECO mode off: 15 W
Dimensions (W x H x D) 190 x 153 x 320 mm
Weight 4.0 kg
SPEAKER SYSTEM SX-LEM60
Speakers system 2 way, bass reflex (magnetic shielded)
Speaker units Woofer: 120 mm cone
Tweeter: 25 mm dome
Impedance 6 ohms
Dimensions (W x H x D) 155 x 250 x 218 mm
Weight 2.3 kg
• Design and specifications are subject to change without notice.
– 3 –
Page 4
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!!
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJECTIVE
LENS ON THE OPTICAL PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid
exposure to beam.
Advarsel: Usynlig laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herin may result in
hazardous radiation exposure.
ATTENTION
L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.
ADVARSEL
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
Precaution to replace Optical block
(KSS – 213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care
the clothes do not touch the diode.
1) After the connection, remove solder
shown in the right figure.
CD PICKUP Assy PWB
Solder
– 4 –
Page 5
ELECTRICAL PARTS LIST (CX – LEM60 / CX – LEM61)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
AMP O C 0097 87-010-831-080 C-CAP,U 0.1-16 Z F a b
AMP X C 0099 88-108-000-080 C-JUMPER,U a b
AMP O C 0103 87-A13-056-080 CAP,E 4.7-50 M FG a b
AMP O C 0104 87-A13-056-080 CAP,E 4.7-50 M FG a b
AMP O C 0105 87-012-273-080 C-CAP,U 820P-50 K B a b
AMP O C 0106 87-012-273-080 C-CAP,U 820P-50 K B a b
AMP O C 0107 87-A12-072-080 CAP,E 100-25 SMG a b
AMP O C 0108 87-A12-072-080 CAP,E 100-25 SMG a b
AMP O C 0109 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP O C 0110 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP O C 0111 87-A12-076-080 CAP,E 22-35 SMG a b
AMP O C 0112 87-A12-076-080 CAP,E 22-35 SMG a b
AMP O C 0113 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP O C 0114 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP O C 0117 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
AMP O C 0118 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
AMP O C 0119 87-012-286-080 C-CAP,U 0.01-25 K B a b
AMP O C 0120 87-012-286-080 C-CAP,U 0.01-25 K B a b
AMP O C 0123 87-012-273-080 C-CAP,U 820P-50 K B a b
AMP O C 0124 87-012-273-080 C-CAP,U 820P-50 K B a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP O C 0133 87-012-282-080 C-CAP,U 4700P-50 K B a b
AMP O C 0140 87-012-278-080 C-CAP,U 2200P-50 K B a b
AMP O C 0186 87-010-831-080 C-CAP,U 0.1-16 Z F a b
AMP O C 0187 87-A12-091-080 CAP,E 10-50 SMG a b
AMP O C 0188 87-A12-091-080 CAP,E 10-50 SMG a b
AMP O C 0193 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
AMP O C 0194 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
AMP O CN 0101 87-A61-013-010 CONN,15P H BLK TAC-L15P-A3 a b
AMP S D 0103 87-020-465-080 DIODE,1SS133 a b
AMP S D 0104 87-020-465-080 DIODE,1SS133 a b
AMP S D 0105 87-020-465-080 DIODE,1SS133 a b
AMP S D 0106 87-020-465-080 DIODE,1SS133 a b
AMP S D 0107 87-020-465-080 DIODE,1SS133 a b
AMP S D 0108 87-020-465-080 DIODE,1SS133 a b
AMP S D 0115 87-A40-270-080 C-DIODE,MC2838 a b
AMP S D 0117 87-020-465-080 DIODE,1SS133 a b
AMP S D 0118 87-020-465-080 DIODE,1SS133 a b
AMP S D 0119 87-020-465-080 DIODE,1SS133 a b
AMP S D 0120 87-020-465-080 DIODE,1SS133 a b
AMP S D 0150 87-A40-270-080 C-DIODE,MC2838 a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP S D 0160 87-A40-270-080 C-DIODE,MC2838 a b
AMP S D 0185 87-070-178-090 DIODE,1N5402-BD54 a b
AMP S D 0186 87-070-178-090 DIODE,1N5402-BD54 a b
AMP S D 0187 87-070-136-080 ZENER,MTZJ5.1B a b
AMP S D 0188 87-017-931-080 ZENER,MTZJ5.6B a b
AMP S D 0189 87-A40-270-080 C-DIODE,MC2838 a b
AMP S D 0190 87-A40-269-080 C-DIODE,MC2836 a b
AMP S D 0191 87-A40-345-080 ZENER,MTZJ10C a b
AMP S D 0192 87-020-465-080 DIODE,1SS133 a b
AMP S D 0193 87-020-465-080 DIODE,1SS133 a b
AMP S D 0262 87-A40-270-080 C-DIODE,MC2838 a b
AMP S D 0265 87-A40-269-080 C-DIODE,MC2836 a b
AMP O JR 0123 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP O JR 0124 87-012-257-080 C-CAP,U 47P-50 J UJ a b
AMP S Q 0103 87-A30-075-080 C-TR,2SA1235F a b
AMP S Q 0104 87-A30-075-080 C-TR,2SA1235F a b
AMP S Q 0105 87-A30-075-080 C-TR,2SA1235F a b
AMP S Q 0106 87-A30-075-080 C-TR,2SA1235F a b
AMP S Q 0107 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0108 87-A30-076-080 C-TR,2SC3052F a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP S Q 0109 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0110 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0111 87-A30-672-080 TR,2N5551C a b
AMP S Q 0112 87-A30-672-080 TR,2N5551C a b
AMP S Q 0113 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0114 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0115 87-A30-670-040 C-TR,SBT5551 a b
AMP S Q 0116 87-A30-670-040 C-TR,SBT5551 a b
AMP S Q 0117 87-A30-255-010 TR,2SB1342 a b
AMP S Q 0118 87-A30-255-010 TR,2SB1342 a b
AMP S Q 0119 87-A30-256-010 TR,2SD1933 a b
AMP S Q 0120 87-A30-256-010 TR,2SD1933 a b
AMP S Q 0123 87-A30-669-040 C-TR,SBT5401 a b
AMP S Q 0124 87-A30-669-040 C-TR,SBT5401 a b
AMP S Q 0126 87-A30-669-040 C-TR,SBT5401 a b
AMP S Q 0127 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0128 87-A30-076-080 C-TR,2SC3052F a b
AMP S Q 0130 87-A30-670-040 C-TR,SBT5551 a b
AMP S Q 0183 87-A30-162-010 FET,2SK2937 a b
AMP S Q 0184 87-A30-162-010 FET,2SK2937 a b
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 5 –
Page 6
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
AMP S Q 0185 87-A30-547-040 C-TR,2SD1819AQRS a b
AMP S Q 0186 87-A30-548-040 C-TR,2SB1218AQRS a b
AMP S Q 0187 87-A30-548-040 C-TR,2SB1218AQRS a b
AMP S Q 0259 87-A30-548-040 C-TR,2SB1218AQRS a b
AMP S Q 0265 87-A30-538-040 C-TR,SRA2202S a b
AMP X R 0101 88-118-222-080 C-RES,S 2.2K-1/10W J a b
AMP X R 0102 88-118-222-080 C-RES,S 2.2K-1/10W J a b
AMP X R 0103 88-118-223-080 C-RES,S 22K-1/10W J a b
AMP X R 0104 88-118-223-080 C-RES,S 22K-1/10W J a b
AMP X R 0105 88-108-273-080 C-RES,U 27K-1/16W J a b
AMP X R 0106 88-108-273-080 C-RES,U 27K-1/16W J a b
AMP X R 0107 88-108-101-080 C-RES,U 100-1/16W J a b
AMP X R 0108 88-108-101-080 C-RES,U 100-1/16W J a b
AMP X R 0109 88-121-101-080 RES,100-1/8W J a b
AMP X R 0110 88-121-101-080 RES,100-1/8W J a b
AMP X R 0111 88-108-102-080 C-RES,U 1K-1/16W J a b
AMP X R 0112 88-108-102-080 C-RES,U 1K-1/16W J a b
AMP X R 0113 88-118-183-080 C-RES,S 18K-1/10W J a b
AMP X R 0114 88-118-183-080 C-RES,S 18K-1/10W J a b
AMP X R 0117 88-121-103-080 RES,10K-1/8W J a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP X R 0118 88-121-103-080 RES,10K-1/8W J a b
AMP X R 0119 88-118-101-080 C-RES,S 100-1/10W J a b
AMP X R 0120 88-118-101-080 C-RES,S 100-1/10W J a b
AMP X R 0121 88-118-101-080 C-RES,S 100-1/10W J a b
AMP X R 0122 88-118-101-080 C-RES,S 100-1/10W J a b
AMP X R 0123 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0124 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0125 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0126 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0127 88-118-390-080 C-RES,S 39-1/10W J a b
AMP X R 0128 88-118-390-080 C-RES,S 39-1/10W J a b
AMP O R 0129 87-A00-258-080 RES,M/F 0.22-1W J a b
AMP O R 0130 87-A00-258-080 RES,M/F 0.22-1W J a b
AMP O R 0131 87-A00-258-080 RES,M/F 0.22-1W J a b
AMP O R 0132 87-A00-258-080 RES,M/F 0.22-1W J a b
AMP X R 0133 88-108-332-080 C-RES,U 3.3K-1/16W J a b
AMP X R 0134 88-108-332-080 C-RES,U 3.3K-1/16W J a b
AMP X R 0135 88-108-152-080 C-RES,U 1.5K-1/16W J a b
AMP X R 0136 88-108-152-080 C-RES,U 1.5K-1/16W J a b
AMP X R 0137 88-108-101-080 C-RES,U 100-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP X R 0138 88-108-101-080 C-RES,U 100-1/16W J a b
AMP X R 0141 88-118-102-080 C-RES,S 1K-1/10W J a b
AMP X R 0142 88-118-102-080 C-RES,S 1K-1/10W J a b
AMP X R 0151 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0152 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0155 88-108-392-080 C-RES,U 3.9K-1/16W J a b
AMP X R 0156 88-108-392-080 C-RES,U 3.9K-1/16W J a b
AMP X R 0157 88-121-472-080 RES,4.7K-1/8W J a b
AMP X R 0158 88-128-272-080 C-RES, 2.7K-1/8W J a b
AMP X R 0159 88-108-103-080 C-RES,U 10K-1/16W J a b
AMP X R 0160 88-118-103-080 C-RES,S 10K-1/10W J a b
AMP X R 0161 88-108-472-080 C-RES,U 4.7K-1/16W J a b
AMP X R 0162 88-108-472-080 C-RES,U 4.7K-1/16W J a b
AMP X R 0163 88-108-472-080 C-RES,U 4.7K-1/16W J a b
AMP X R 0164 88-108-472-080 C-RES,U 4.7K-1/16W J a b
AMP X R 0165 88-108-152-080 C-RES,U 1.5K-1/16W J a b
AMP X R 0166 88-108-152-080 C-RES,U 1.5K-1/16W J a b
AMP X R 0167 88-108-103-080 C-RES,U 10K-1/16W J a b
AMP X R 0168 88-118-473-080 C-RES,S 47K-1/10W J a b
AMP X R 0169 88-118-271-080 C-RES,S 270-1/10W J a b
CX-LEM60 CX-LEM61
KSM EZSM
AMP X R 0170 88-118-271-080 C-RES,S 270-1/10W J a b
AMP X R 0171 88-118-222-080 C-RES,S 2.2K-1/10W J a b
AMP X R 0172 88-118-222-080 C-RES,S 2.2K-1/10W J a b
AMP X R 0173 88-118-152-080 C-RES,S 1.5K-1/10W J a b
AMP X R 0174 88-118-152-080 C-RES,S 1.5K-1/10W J a b
AMP X R 0175 88-118-331-080 C-RES,S 330-1/10W J a b
AMP X R 0176 88-118-331-080 C-RES,S 330-1/10W J a b
AMP X R 0177 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0178 88-118-103-080 C-RES,S 10K-1/10W J a b
AMP X R 0179 88-108-103-080 C-RES,U 10K-1/16W J a b
AMP X R 0180 88-108-103-080 C-RES,U 10K-1/16W J a b
AMP X R 0184 88-118-102-080 C-RES,S 1K-1/10W J a b
AMP X R 0185 88-118-103-080 C-RES,S 10K-1/10W J a b
AMP X R 0186 88-118-222-080 C-RES,S 2.2K-1/10W J a b
AMP X R 0187 88-108-332-080 C-RES,U 3.3K-1/16W J a b
AMP X R 0188 88-118-102-080 C-RES,S 1K-1/10W J a b
AMP X R 0189 88-128-272-080 C-RES, 2.7K-1/8W J a b
AMP X R 0190 88-128-272-080 C-RES, 2.7K-1/8W J a b
AMP X R 0192 88-128-222-080 C-RES, 2.2K-1/8W J a b
AMP X R 0194 88-108-103-080 C-RES,U 10K-1/16W J a b
– 6 –
Page 7
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
AMP X R 0195 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0196 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0197 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0198 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0199 88-108-225-080 C-RES,U 2.2M-1/16W J a b
AMP X R 0252 88-108-104-080 C-RES,U 100K-1/16W J a b
AMP X R 0257 88-108-182-080 C-RES,U 1.8K-1/16W J a b
AMP X R 0259 88-108-103-080 C-RES,U 10K-1/16W J a b
AMP X R 0260 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0266 88-108-104-080 C-RES,U 100K-1/16W J a b
AMP X R 0268 88-108-104-080 C-RES,U 100K-1/16W J a b
AMP X R 0269 88-108-104-080 C-RES,U 100K-1/16W J a b
AMP X R 0271 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP X R 0272 88-108-473-080 C-RES,U 47K-1/16W J a b
AMP O TH 0101 87-A91-042-080 C-THMS,100K 55001 a b
AMP O TH 0102 87-A91-042-080 C-THMS,100K 55001 a b
FRONT O C 0501 87-012-274-080 C-CAP,U 1000P-50 K B a b
FRONT O C 0502 87-A12-091-080 CAP,E 10-50 SMG a b
FRONT O C 0503 87-A12-069-080 CAP,E 22-25 SMG a b
FRONT O C 0504 87-012-286-080 C-CAP,U 0.01-25 K B a b
CX-LEM60 CX-LEM61
KSM EZSM
FRONT O C 0505 87-012-286-080 C-CAP,U 0.01-25 K B a b
FRONT O C 0506 87-012-286-080 C-CAP,U 0.01-25 K B a b
FRONT O C 0507 87-012-286-080 C-CAP,U 0.01-25 K B a b
FRONT O C 0508 87-012-286-080 C-CAP,U 0.01-25 K B a b
FRONT O C 0509 87-012-286-080 C-CAP,U 0.01-25 K B a b
FRONT O C 0510 87-A12-069-080 CAP,E 22-25 SMG a b
FRONT O CN 0501 87-099-720-010 CONN,30P BLK TYK-B(P) a b
FRONT O CN 0502 87-099-754-010 CONN,13P H 9604 a b
FRONT O CN 0503 87-A60-667-010 CONN,3P H 2MM JMT a b
FRONT O D 0501 87-A40-317-080 LED,SLR-342VCT31 RED a b
FRONT O FFC0502 88-913-221-110 FF-CABLE, 13P 1.25 220MM a b
FRONT O FL 0501 8C-CL4-630-010 FL,HNA-10SM19 a b
FRONT S IC 0501 87-A22-043-010 IC,SPS-440-1-E1 a b
FRONT X R 0501 88-108-563-080 C-RES,U 56K-1/16W J a b
FRONT X R 0502 88-108-221-080 C-RES,U 220-1/16W J a b
FRONT X R 0503 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0504 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0505 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0506 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0507 88-108-223-080 C-RES,U 22K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
FRONT X R 0509 88-108-272-080 C-RES,U 2.7K-1/16W J a b
FRONT X R 0510 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0511 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0512 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0513 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0514 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0515 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0516 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0517 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0518 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0519 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0520 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0521 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0522 88-108-223-080 C-RES,U 22K-1/16W J a b
FRONT X R 0523 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0524 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0525 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0526 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0527 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0528 88-108-104-080 C-RES,U 100K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
FRONT X R 0529 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0530 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0531 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0532 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0533 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT X R 0534 88-108-223-080 C-RES,U 22K-1/16W J a b
FRONT X R 0535 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0536 88-108-103-080 C-RES,U 10K-1/16W J a b
FRONT O R 0538 87-022-239-080 C-RES,U 10K-1/16W F a b
FRONT O R 0539 87-022-239-080 C-RES,U 10K-1/16W F a b
FRONT X R 0540 88-108-272-080 C-RES,U 2.7K-1/16W J a b
FRONT X R 0541 88-108-272-080 C-RES,U 2.7K-1/16W J a b
FRONT X R 0542 88-108-102-080 C-RES,U 1K-1/16W J a b
FRONT X R 0543 88-108-102-080 C-RES,U 1K-1/16W J a b
FRONT X R 0544 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0545 88-108-472-080 C-RES,U 4.7K-1/16W J a b
FRONT X R 0546 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0547 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0548 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0549 88-108-104-080 C-RES,U 100K-1/16W J a b
– 7 –
Page 8
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
FRONT X R 0550 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0551 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0552 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0553 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT X R 0555 88-108-104-080 C-RES,U 100K-1/16W J a b
FRONT O S 0501 87-A92-353-010 SW,RTRY RE0123PVB25FINA1-2 a b
FRONT O S 0502 87-A92-353-010 SW,RTRY RE0123PVB25FINA1-2 a b
FRONT O S 0503 87-A92-291-010 SW,RTRY RE121PVB25FINB1-24E a b
FRONT O S 0505 87-A90-095-080 SW,TACT EVQ11G04M a b
FRONT O S 0507 87-A90-095-080 SW,TACT EVQ11G04M a b
FRONT O S 0508 87-A90-095-080 SW,TACT EVQ11G04M a b
HP O CN 0602 87-099-407-010 CONN,7P V WHT EH a b
HP O J 0603 87-A61-821-010 JACK,3.5 BLK ST W/SW GLD a b
KEY X R 0554 88-108-472-080 C-RES,U 4.7K-1/16W J a b
KEY X R 0556 88-108-392-080 C-RES,U 3.9K-1/16W J a b
KEY X R 0557 88-108-392-080 C-RES,U 3.9K-1/16W J a b
KEY X R 0558 88-108-103-080 C-RES,U 10K-1/16W J a b
KEY X R 0559 88-108-103-080 C-RES,U 10K-1/16W J a b
KEY X R 0560 88-108-153-080 C-RES,U 15K-1/16W J a b
KEY X R 0561 88-108-153-080 C-RES,U 15K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
KEY O S 0509 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0510 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0511 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0512 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0513 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0514 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0515 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0516 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O S 0517 87-A90-095-080 SW,TACT EVQ11G04M a b
KEY O CNA0501 88-805-030-820 CONN ASSY,3P 80 a b
MAIN O C 0003 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
MAIN O C 0004 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
MAIN O C 0005 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
MAIN O C 0006 87-A12-317-080 C-CAP,U 0.1-50 Z F a b
MAIN O C 0009 87-010-759-080 C-CAP,U 0.1-25 Z F a b
MAIN O C 0010 87-010-759-080 C-CAP,U 0.1-25 Z F a b
MAIN O C 0011 87-010-759-080 C-CAP,U 0.1-25 Z F a b
MAIN O C 0012 87-010-759-080 C-CAP,U 0.1-25 Z F a b
MAIN O C 0019 87-016-051-000 CAP,E 2200-35 M SMG a b
MAIN O C 0020 87-016-051-000 CAP,E 2200-35 M SMG a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0021 87-010-928-000 CAP,E 4700-25 M SMG a b
MAIN O C 0022 87-010-928-000 CAP,E 4700-25 M SMG a b
MAIN O C 0025 87-A12-095-080 CAP,E 100-50 SMG a b
MAIN O C 0026 87-A12-095-080 CAP,E 100-50 SMG a b
MAIN O C 0030 87-A12-079-080 CAP,E 100-35 SMG a b
MAIN O C 0031 87-A12-072-080 CAP,E 100-25 SMG a b
MAIN O C 0037 87-A12-079-080 CAP,E 100-35 SMG a b
MAIN O C 0038 87-012-282-080 C-CAP,U 4700P-50 K B a b
MAIN O C 0045 87-010-759-080 C-CAP,U 0.1-25 Z F a b
MAIN O C 0046 87-A12-068-080 CAP,E 470-16 SMG a b
MAIN O C 0047 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0050 87-A12-068-080 CAP,E 470-16 SMG a b
MAIN O C 0051 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0052 87-A12-068-080 CAP,E 470-16 SMG a b
MAIN O C 0054 87-A13-061-080 CAP,E 330-16 M ASF WHT a b
MAIN O C 0060 87-A12-089-080 CAP,E 3.3-50 SMG a b
MAIN O C 0061 87-A12-071-080 CAP,E 47-25 SMG a b
MAIN O C 0083 87-A12-074-080 CAP,E 470-25 SMG a b
MAIN O C 0301 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0302 87-010-831-080 C-CAP,U 0.1-16 Z F a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0303 87-A12-089-080 CAP,E 3.3-50 SMG a b
MAIN O C 0304 87-A12-090-080 CAP,E 4.7-50 SMG a b
MAIN O C 0305 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0306 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0307 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0308 87-010-992-080 C-CAP,S 0.047-25 K B MK212 a b
MAIN O C 0309 87-A12-089-080 CAP,E 3.3-50 SMG a b
MAIN O C 0310 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0311 87-010-992-080 C-CAP,S 0.047-25 K B MK212 a b
MAIN O C 0312 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0313 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0314 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0315 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0316 87-012-188-080 C-CAP,U 47P-50 J CH a b
MAIN O C 0317 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0318 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0319 87-012-282-080 C-CAP,U 4700P-50 K B a b
MAIN O C 0321 87-012-172-080 C-CAP,U 10P-50 D CH a b
MAIN O C 0322 87-A12-091-080 CAP,E 10-50 SMG a b
MAIN O C 0323 87-010-831-080 C-CAP,U 0.1-16 Z F a b
– 8 –
Page 9
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0325 87-012-284-080 C-CAP,U 6800P-50 K B GRM a b
MAIN O C 0326 87-012-169-080 C-CAP,U 7P-50 D CH a b
MAIN O C 0327 87-A12-087-080 CAP,E 1-50 SMG a b
MAIN O C 0328 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0329 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0331 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0332 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0333 87-012-188-080 C-CAP,U 47P-50 J CH a b
MAIN O C 0334 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0335 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0336 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0337 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0338 87-A13-060-080 CAP,E 220-10 M ASF WHT a b
MAIN O C 0339 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0340 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0341 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0342 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0343 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0344 87-012-180-080 C-CAP,U 22P-50 J CH a b
MAIN O C 0345 87-A12-091-080 CAP,E 10-50 SMG a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0347 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0348 87-A12-091-080 CAP,E 10-50 SMG a b
MAIN O C 0349 87-A12-088-080 CAP,E 2.2-50 SMG a b
MAIN O C 0351 87-A13-057-080 CAP,E 10-50 M FG a b
MAIN O C 0352 87-A13-057-080 CAP,E 10-50 M FG a b
MAIN O C 0355 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0356 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0357 87-A12-062-080 CAP,E 100-10 SMG a b
MAIN O C 0358 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0365 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0367 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0370 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0371 87-012-286-080 C-CAP,U 0.01-25 K B a b
MAIN O C 0374 87-012-279-080 C-CAP,U 2700P-50 K B GRM a b
MAIN O C 0375 87-012-279-080 C-CAP,U 2700P-50 K B GRM a b
MAIN O C 0401 87-012-270-080 C-CAP,U 470P-50 K B a b
MAIN O C 0402 87-A12-094-080 CAP,E 47-50 SMG a b
MAIN O C 0403 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0405 87-012-174-080 C-CAP,U 12P-50 J CH a b
MAIN O C 0406 87-A10-781-080 C-CAP,U 0.15-10 K B a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0407 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0408 87-012-184-080 C-CAP,U 33P-50 J CH a b
MAIN O C 0409 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0410 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0411 87-A12-063-080 CAP,E 220-10 SMG a b
MAIN O C 0412 87-012-287-080 C-CAP,U 0.015-25 Z F a b
MAIN O C 0413 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0414 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0415 87-010-829-080 C-CAP,U 0.047-16 Z F a b
MAIN O C 0601 87-A13-044-080 CAP,E 100-16 M VR-GSO a b
MAIN O C 0602 87-A13-044-080 CAP,E 100-16 M VR-GSO a b
MAIN O C 0607 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0608 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0609 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN O C 0610 87-012-274-080 C-CAP,U 1000P-50 K B a b
MAIN X C 0615 88-707-939-810 CAP,M 0.22-50 J TF a b
MAIN X C 0616 88-707-939-810 CAP,M 0.22-50 J TF a b
MAIN X C 0617 88-707-939-810 CAP,M 0.22-50 J TF a b
MAIN X C 0618 88-707-939-810 CAP,M 0.22-50 J TF a b
MAIN O C 0619 87-A13-058-080 CAP,E 47-25 M FW a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0620 87-A13-058-080 CAP,E 47-25 M FW a b
MAIN O C 0621 87-012-188-080 C-CAP,U 47P-50 J CH a b
MAIN O C 0622 87-012-188-080 C-CAP,U 47P-50 J CH a b
MAIN O C 0625 87-012-272-080 C-CAP,U 680P-50 K B GRM a b
MAIN O C 0626 87-012-272-080 C-CAP,U 680P-50 K B GRM a b
MAIN O C 0627 87-012-269-080 C-CAP,U 390P-50 K B a b
MAIN O C 0628 87-012-269-080 C-CAP,U 390P-50 K B a b
MAIN O C 0631 87-012-271-080 C-CAP,U 560P-50 K B a b
MAIN O C 0632 87-012-271-080 C-CAP,U 560P-50 K B a b
MAIN O C 0650 87-A12-061-080 CAP,E 47-10 SMG a b
MAIN O C 0651 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0661 87-012-336-080 C-CAP,U 330P-50 J SL a b
MAIN O C 0662 87-012-336-080 C-CAP,U 330P-50 J SL a b
MAIN O C 0673 87-A12-376-080 CAP,M 0.1-100 J CP a b
MAIN O C 0674 87-A12-376-080 CAP,M 0.1-100 J CP a b
MAIN O C 0675 87-A12-376-080 CAP,M 0.1-100 J CP a b
MAIN O C 0676 87-A12-376-080 CAP,M 0.1-100 J CP a b
MAIN O C 0677 87-012-286-080 C-CAP,U 0.01-25 K B a b
MAIN O C 0679 87-018-133-080 CAP,TC U 4700P-16 N X UP050 a b
MAIN O C 0680 87-018-133-080 CAP,TC U 4700P-16 N X UP050 a b
– 9 –
Page 10
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O C 0684 87-010-831-080 C-CAP,U 0.1-16 Z F a b
MAIN O C 0861 87-A12-091-080 CAP,E 10-50 SMG . b
MAIN O C 0862 87-010-831-080 C-CAP,U 0.1-16 Z F . b
MAIN O C 0863 87-012-199-080 C-CAP,U 220P-50 J CH . b
MAIN O C 0864 87-012-199-080 C-CAP,U 220P-50 J CH . b
MAIN O C 0865 87-012-274-080 C-CAP,U 1000P-50 K B . b
MAIN O C 0866 87-012-270-080 C-CAP,U 470P-50 K B . b
MAIN O C 0867 87-012-286-080 C-CAP,U 0.01-25 K B . b
MAIN O C 0868 87-A12-091-080 CAP,E 10-50 SMG . b
MAIN O C 0869 87-012-286-080 C-CAP,U 0.01-25 K B . b
MAIN O C 0870 87-012-184-080 C-CAP,U 33P-50 J CH . b
MAIN O C 0871 87-012-180-080 C-CAP,U 22P-50 J CH . b
MAIN O C 0872 87-012-280-080 C-CAP,U 3300P-50 K B a b
MAIN O C 0873 87-012-280-080 C-CAP,U 3300P-50 K B a b
MAIN O CN 0301 87-A60-424-010 CONN,16P V TOC-B a b
MAIN O CN 0302 87-A60-061-010 CONN,06P V 9604S-06C a b
MAIN O CN 0303 87-A60-062-010 CONN,05P V 9604S-05C a b
MAIN O CN 0401 87-099-719-010 CONN,30P H BLK TYK-B(X) a b
MAIN O CN 0402 87-099-015-010 CONN,13P V BLK 6216 a b
MAIN O CN 0601 87-A60-189-010 CONN,16P V TUC-P16P-B1 a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN O CN 0603 87-A60-998-010 CONN,15P V BLK TAC-L15X-A3 a b
MAIN O CNA0001 8C-CL4-650-010 CONN ASSY,9P SUPPLY a b
MAIN O CNA0601 8C-CL4-651-010 CONN ASSY,7P HP EH a b
MAIN S D 0001 87-A40-838-090 DIODE,G3SBA60L-6088 a b
MAIN S D 0002 87-A40-838-090 DIODE,G3SBA60L-6088 a b
MAIN S D 0024 87-070-274-080 DIODE,1N4003 SEM a b
MAIN S D 0027 87-070-274-080 DIODE,1N4003 SEM a b
MAIN S D 0029 87-002-743-080 ZENER,MTZJ33B a b
MAIN S D 0033 87-070-274-080 DIODE,1N4003 SEM a b
MAIN S D 0041 87-A40-270-080 C-DIODE,MC2838 a b
MAIN S D 0042 87-A40-269-080 C-DIODE,MC2836 a b
MAIN S D 0061 87-020-465-080 DIODE,1SS133 a b
MAIN S D 0063 87-A40-270-080 C-DIODE,MC2838 a b
MAIN S D 0064 87-A40-269-080 C-DIODE,MC2836 a b
MAIN S D 0071 87-A40-269-080 C-DIODE,MC2836 a b
MAIN S D 0072 87-A40-270-080 C-DIODE,MC2838 a b
MAIN S D 0076 87-A40-269-080 C-DIODE,MC2836 a b
MAIN S D 0077 87-A40-270-080 C-DIODE,MC2838 a b
MAIN S D 0301 87-070-136-080 ZENER,MTZJ5.1B a b
MAIN S D 0302 87-A40-003-080 ZENER,MTZJ4.3A a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN S D 0401 87-017-931-080 ZENER,MTZJ5.6B a b
MAIN S D 0402 87-020-465-080 DIODE,1SS133 a b
MAIN S D 0403 87-020-465-080 DIODE,1SS133 a b
MAIN S D 0404 87-A40-270-080 C-DIODE,MC2838 a b
MAIN S D 0601 87-A40-243-080 ZENER,MTZ J 4.7BT-72 a b
MAIN S D 0602 87-A40-243-080 ZENER,MTZ J 4.7BT-72 a b
MAIN S D 0603 87-020-465-080 DIODE,1SS133 a b
MAIN S D 0604 87-A40-243-080 ZENER,MTZ J 4.7BT-72 a b
MAIN S D 0861 87-020-465-080 DIODE,1SS133 . b
MAIN O FFC0301 8C-CL4-652-010 FF-CABLE,16P 1.00 a b
MAIN O FFC0302 88-906-101-110 FF-CABLE, 6P 1.25 a b
MAIN O FFC0303 88-905-231-110 FF-CABLE, 5P 1.25 230MM a b
MAIN S IC 0001 87-001-576-010 IC,NJM7812FA a b
MAIN S IC 0002 87-A21-364-010 IC,NJM7806FA(A) a b
MAIN S IC 0301 87-A22-242-030 C-IC,LC78646E a b
MAIN S IC 0302 87-A22-251-040 C-IC,BA5826FP a b
MAIN S IC 0303 87-002-394-010 IC,LB1641 a b
MAIN S IC 0401 8C-CL4-601-030 C-IC,LC876748A-5Z30 a b
MAIN S IC 0601 87-A22-264-040 C-IC,BD3882FV a b
MAIN S IC 0602 87-017-825-010 IC,GP1F32T a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN S IC 0860 87-A20-440-040 C-IC,BU1920FS . b
MAIN O J 0601 87-A61-711-010 JACK,PIN 2P MSP- 242V-01 PBSN a b
MAIN O J 0602 87-A60-568-010 JACK,PIN 3P B/W/R HSP-243V19 a b
MAIN O J 0605 87-A61-712-010 TERMINAL, 4P SP MSP-324V1-01 a b
MAIN O JW 0411 87-008-372-080 FLTR,EMI BL01 RN1 a b
MAIN O JW 0421 87-008-372-080 FLTR,EMI BL01 RN1 a b
MAIN O L 0301 87-003-102-080 COIL,10UH J LAL02 a b
MAIN O L 0302 87-003-102-080 COIL,10UH J LAL02 a b
MAIN O L 0401 87-A50-333-010 COIL,OSC 9.43MHZ a b
MAIN O L 0601 87-A50-610-010 COIL,1UH K(MDEC) a b
MAIN O L 0602 87-A50-610-010 COIL,1UH K(MDEC) a b
MAIN O L 0861 87-003-098-080 COIL,2.2UH K LAL02 . b
MAIN S Q 0001 87-A30-494-080 TR,2SA1980G a b
MAIN S Q 0002 87-A30-494-080 TR,2SA1980G a b
MAIN S Q 0003 89-406-555-080 TR,2SD655E a b
MAIN S Q 0008 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0014 87-A30-548-040 C-TR,2SB1218AQRS a b
MAIN S Q 0060 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0061 87-A30-548-040 C-TR,2SB1218AQRS a b
MAIN S Q 0062 87-A30-547-040 C-TR,2SD1819AQRS a b
– 10 –
Page 11
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN S Q 0063 87-A30-548-040 C-TR,2SB1218AQRS a b
MAIN S Q 0064 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0301 89-113-184-080 TR,2SA1318T a b
MAIN S Q 0302 89-406-555-080 TR,2SD655E a b
MAIN S Q 0303 89-213-292-380 TR,2SB1329(Q/R) a b
MAIN S Q 0401 89-113-184-080 TR,2SA1318T a b
MAIN S Q 0402 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0403 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0404 87-A30-076-080 C-TR,2SC3052F a b
MAIN S Q 0405 87-A30-538-040 C-TR,SRA2202S a b
MAIN S Q 0601 87-A30-548-040 C-TR,2SB1218AQRS a b
MAIN S Q 0602 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0603 87-A30-547-040 C-TR,2SD1819AQRS a b
MAIN S Q 0860 89-327-125-080 C-TR,2SC2712GR . b
MAIN S Q 0861 89-327-125-080 C-TR,2SC2712GR . b
MAIN X R 0001 88-130-109-080 RES,1-1/4W J a b
MAIN X R 0002 88-130-109-080 RES,1-1/4W J a b
MAIN X R 0003 88-108-471-080 C-RES,U 470-1/16W J a b
MAIN X R 0004 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0005 88-130-109-080 RES,1-1/4W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0006 88-130-109-080 RES,1-1/4W J a b
MAIN X R 0009 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0010 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0011 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0012 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0013 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0014 88-108-100-080 C-RES,U 10-1/16W J a b
MAIN X R 0015 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0019 88-108-000-080 C-JUMPER,U a b
MAIN X R 0028 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0029 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0032 88-108-274-080 C-RES,U 270K-1/16W J a b
MAIN X R 0034 88-121-273-080 RES,27K-1/8W J a b
MAIN X R 0043 88-108-471-080 C-RES,U 470-1/16W J a b
MAIN X R 0044 88-108-823-080 C-RES,U 82K-1/16W J a b
MAIN X R 0054 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0055 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0056 88-108-562-080 C-RES,U 5.6K-1/16W J a b
MAIN X R 0058 88-108-682-080 C-RES,U 6.8K-1/16W J a b
MAIN X R 0060 88-108-102-080 C-RES,U 1K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0061 88-108-333-080 C-RES,U 33K-1/16W J a b
MAIN X R 0062 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0063 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0064 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0065 88-108-123-080 C-RES,U 12K-1/16W J a b
MAIN X R 0067 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0070 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0078 88-108-183-080 C-RES,U 18K-1/16W J a b
MAIN X R 0079 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0081 88-121-101-080 RES,100-1/8W J a b
MAIN X R 0085 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0086 88-108-683-080 C-RES,U 68K-1/16W J a b
MAIN X R 0093 88-121-273-080 RES,27K-1/8W J a b
MAIN X R 0094 88-108-183-080 C-RES,U 18K-1/16W J a b
MAIN X R 0095 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0096 88-121-273-080 RES,27K-1/8W J a b
MAIN X R 0301 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0302 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0303 88-108-123-080 C-RES,U 12K-1/16W J a b
MAIN X R 0304 88-108-122-080 C-RES,U 1.2K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0305 88-108-681-080 C-RES,U 680-1/16W J a b
MAIN X R 0306 88-108-681-080 C-RES,U 680-1/16W J a b
MAIN X R 0307 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0308 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0309 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0310 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0311 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0312 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0313 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0314 88-121-103-080 RES,10K-1/8W J a b
MAIN X R 0315 88-108-339-080 C-RES,U 3.3-1/16W J a b
MAIN X R 0316 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0317 88-121-273-080 RES,27K-1/8W J a b
MAIN X R 0318 88-108-331-080 C-RES,U 330-1/16W J a b
MAIN X R 0319 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0320 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0321 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0322 88-108-333-080 C-RES,U 33K-1/16W J a b
MAIN X R 0323 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0324 88-108-333-080 C-RES,U 33K-1/16W J a b
– 11 –
Page 12
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0325 88-108-221-080 C-RES,U 220-1/16W J a b
MAIN X R 0326 88-108-181-080 C-RES,U 180-1/16W J a b
MAIN X R 0327 88-108-470-080 C-RES,U 47-1/16W J a b
MAIN X R 0328 88-121-100-080 RES,10-1/8W J a b
MAIN X R 0329 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0330 88-108-000-080 C-JUMPER,U a b
MAIN X R 0331 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0332 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0333 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0334 88-108-331-080 C-RES,U 330-1/16W J a b
MAIN X R 0335 88-108-331-080 C-RES,U 330-1/16W J a b
MAIN X R 0336 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0337 88-128-471-080 C-RES, 470-1/8W J a b
MAIN X R 0339 88-140-229-080 RES,2.2-1/2W J a b
MAIN X R 0340 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0341 88-108-822-080 C-RES,U 8.2K-1/16W J a b
MAIN X R 0343 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0344 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0345 88-121-103-080 RES,10K-1/8W J a b
MAIN X R 0346 88-108-822-080 C-RES,U 8.2K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0347 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0348 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0350 88-100-000-010 PLATING-JW, 0.58 SN95 a b
MAIN X R 0353 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0354 88-108-681-080 C-RES,U 680-1/16W J a b
MAIN X R 0355 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0356 88-128-100-080 C-RES, 10-1/8W J a b
MAIN X R 0402 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0404 88-121-101-080 RES,100-1/8W J a b
MAIN X R 0405 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0406 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0407 88-108-000-080 C-JUMPER,U a b
MAIN X R 0408 88-121-101-080 RES,100-1/8W J a b
MAIN X R 0409 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0410 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0411 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0412 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0413 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0414 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0415 88-100-000-010 PLATING-JW, 0.58 SN95 a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0416 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0417 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0418 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0419 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0420 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0421 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0422 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0423 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0424 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0425 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0426 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0427 88-121-100-080 RES,10-1/8W J a b
MAIN X R 0428 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0429 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0430 88-108-683-080 C-RES,U 68K-1/16W J a b
MAIN X R 0431 88-108-683-080 C-RES,U 68K-1/16W J a b
MAIN X R 0432 88-128-224-080 C-RES, 220K-1/8W J a b
MAIN X R 0433 88-128-472-080 C-RES, 4.7K-1/8W J a b
MAIN X R 0434 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0435 88-108-102-080 C-RES,U 1K-1/16W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0436 88-121-821-080 RES,820-1/8W J a b
MAIN X R 0437 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0438 88-108-123-080 C-RES,U 12K-1/16W J a b
MAIN X R 0440 88-108-821-080 C-RES,U 820-1/16W J a b
MAIN X R 0441 88-108-123-080 C-RES,U 12K-1/16W J a b
MAIN X R 0442 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0443 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0444 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0445 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0446 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0447 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0448 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0449 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0450 88-108-471-080 C-RES,U 470-1/16W J a b
MAIN X R 0453 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0457 88-108-104-080 C-RES,U 100K-1/16W J a b
MAIN X R 0458 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0459 88-108-104-080 C-RES,U 100K-1/16W J a .
MAIN X R 0460 88-108-104-080 C-RES,U 100K-1/16W J . b
MAIN X R 0461 88-108-333-080 C-RES,U 33K-1/16W J a b
– 12 –
Page 13
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0462 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0463 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0464 88-108-104-080 C-RES,U 100K-1/16W J . b
MAIN X R 0465 88-108-104-080 C-RES,U 100K-1/16W J a .
MAIN X R 0466 88-108-224-080 C-RES,U 220K-1/16W J a b
MAIN X R 0467 88-108-000-080 C-JUMPER,U a b
MAIN X R 0468 88-108-124-080 C-RES,U 120K-1/16W J a b
MAIN X R 0469 88-108-224-080 C-RES,U 220K-1/16W J a b
MAIN X R 0470 88-121-103-080 RES,10K-1/8W J a b
MAIN X R 0471 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0472 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0473 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0474 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0475 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0476 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0477 88-108-101-080 C-RES,U 100-1/16W J a b
MAIN X R 0601 88-130-101-080 RES,100-1/4W J a b
MAIN X R 0602 88-130-101-080 RES,100-1/4W J a b
MAIN X R 0603 88-130-121-080 RES,120-1/4W J a b
MAIN X R 0604 88-130-121-080 RES,120-1/4W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0605 88-130-121-080 RES,120-1/4W J a b
MAIN X R 0611 88-108-562-080 C-RES,U 5.6K-1/16W J a b
MAIN X R 0612 88-108-562-080 C-RES,U 5.6K-1/16W J a b
MAIN X R 0615 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0616 88-108-472-080 C-RES,U 4.7K-1/16W J a b
MAIN X R 0617 88-108-222-080 C-RES,U 2.2K-1/16W J a b
MAIN X R 0618 88-108-222-080 C-RES,U 2.2K-1/16W J a b
MAIN X R 0619 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0620 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0621 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0622 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0623 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0624 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0625 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0626 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0627 88-108-471-080 C-RES,U 470-1/16W J a b
MAIN X R 0628 88-108-471-080 C-RES,U 470-1/16W J a b
MAIN X R 0629 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0630 88-108-273-080 C-RES,U 27K-1/16W J a b
MAIN X R 0631 88-121-103-080 RES,10K-1/8W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0632 88-121-103-080 RES,10K-1/8W J a b
MAIN X R 0633 88-100-000-010 PLATING-JW, 0.58 SN95 a b
MAIN X R 0634 88-100-000-010 PLATING-JW, 0.58 SN95 a b
MAIN X R 0636 88-121-332-080 RES,3.3K-1/8W J a b
MAIN X R 0637 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0638 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0639 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0640 88-108-153-080 C-RES,U 15K-1/16W J a b
MAIN X R 0641 88-108-000-080 C-JUMPER,U a b
MAIN X R 0642 88-108-000-080 C-JUMPER,U a b
MAIN X R 0644 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0645 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0646 88-128-000-080 C-JUMPER,3216 a b
MAIN X R 0647 88-128-000-080 C-JUMPER,3216 a b
MAIN X R 0650 88-108-121-080 C-RES,U 120-1/16W J a b
MAIN X R 0661 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0662 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0671 88-130-100-080 RES,10-1/4W J a b
MAIN X R 0672 88-130-100-080 RES,10-1/4W J a b
MAIN X R 0673 88-128-100-080 C-RES, 10-1/8W J a b
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0674 88-128-100-080 C-RES, 10-1/8W J a b
MAIN X R 0675 88-130-221-080 RES,220-1/4W J a b
MAIN X R 0676 88-130-221-080 RES,220-1/4W J a b
MAIN X R 0678 88-130-221-080 RES,220-1/4W J a b
MAIN X R 0679 88-130-221-080 RES,220-1/4W J a b
MAIN X R 0680 88-108-122-080 C-RES,U 1.2K-1/16W J a b
MAIN X R 0681 88-108-223-080 C-RES,U 22K-1/16W J a b
MAIN X R 0682 88-108-223-080 C-RES,U 22K-1/16W J a b
MAIN X R 0683 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0684 88-108-102-080 C-RES,U 1K-1/16W J a b
MAIN X R 0685 88-121-102-080 RES,1K-1/8W J a b
MAIN X R 0686 88-108-103-080 C-RES,U 10K-1/16W J a b
MAIN X R 0861 88-108-471-080 C-RES,U 470-1/16W J . b
MAIN X R 0862 88-108-102-080 C-RES,U 1K-1/16W J . b
MAIN X R 0863 88-108-102-080 C-RES,U 1K-1/16W J . b
MAIN X R 0864 88-108-272-080 C-RES,U 2.7K-1/16W J . b
MAIN X R 0865 88-108-104-080 C-RES,U 100K-1/16W J . b
MAIN X R 0866 88-108-123-080 C-RES,U 12K-1/16W J . b
MAIN X R 0867 88-108-104-080 C-RES,U 100K-1/16W J . b
MAIN X R 0868 88-108-471-080 C-RES,U 470-1/16W J . b
– 13 –
Page 14
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
MAIN X R 0876 88-108-222-080 C-RES,U 2.2K-1/16W J a b
MAIN X R 0877 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0878 88-108-000-080 C-JUMPER,U a b
MAIN X R 0880 88-108-473-080 C-RES,U 47K-1/16W J a b
MAIN X R 0882 88-108-000-080 C-JUMPER,U a b
MAIN X R 0883 88-108-222-080 C-RES,U 2.2K-1/16W J a b
MAIN O WH 0001 87-A90-510-010 HLDR,WIRE 2.5-9P a b
MAIN O X 0301 87-A70-363-010 VIB,XTAL 16.9344MHZ CSA-309 a b
MAIN O X 0862 87-A70-307-010 VIB,XTAL 4.332MHZ CSA-309ST . b
PT ! O C 0201 87-A10-479-080 CAP,CER 2200P-250 M E KH a b
PT O CN 0201 87-A61-110-010 CONN,9P V TID-A a b
PT ! O CN 0202 87-099-674-010 CONN,2P V VA a b
PT S D 0251 87-020-465-080 DIODE,1SS133 a b
PT S D 0252 87-020-465-080 DIODE,1SS133 a b
PT S D 0253 87-020-465-080 DIODE,1SS133 a b
PT S D 0254 87-020-465-080 DIODE,1SS133 a b
PT S D 0255 87-020-465-080 DIODE,1SS133 a b
PT ! O PT 0251 8B-NF9-665-010 PT,SUB BNF E (TAM) a b
PT ! O PT 0580 8C-CL4-640-010 PT,CCL-4 EZ a b
PT ! O RY 0251 87-A91-418-010 RELAY,AC12V G5PA-1-M a b
– 14 –
Page 15
ELECTRICAL PARTS LIST (CZA – 3)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CZA-3
EZM
TUNER O C 0772 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0781 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0782 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0783 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0785 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0786 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0788 87-012-167-080 C-CAP,U 5P-50 C CH a
TUNER O C 0789 87-A11-228-080 C-CAP,U 0.027-25 K B a
TUNER O C 0790 87-A11-228-080 C-CAP,U 0.027-25 K B a
TUNER O C 0792 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0793 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0795 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0796 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0797 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0799 87-A12-070-040 CAP,E 33-25 SMG a
TUNER O C 0800 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0801 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0802 87-010-829-080 C-CAP,U 0.047-16 Z F a
TUNER O C 0804 87-A12-062-040 CAP,E 100-10 SMG a
TUNER O C 0807 87-A10-463-080 C-CAP,U 0.47-10 Z F a
CZA-3
EZM
TUNER O C 0808 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0809 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0814 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0815 87-A10-463-080 C-CAP,U 0.47-10 Z F a
TUNER O C 0816 87-A10-463-080 C-CAP,U 0.47-10 Z F a
TUNER O C 0818 87-012-276-080 C-CAP,U 1500P-50 K B GRM a
TUNER O C 0821 87-A11-796-080 C-CAP,S 4.7-10 Z F a
TUNER O C 0823 87-012-274-080 C-CAP,U 1000P-50 K B GRM a
TUNER O C 0824 87-A11-796-080 C-CAP,S 4.7-10 Z F a
TUNER O C 0825 87-A11-317-080 C-CAP,U 0.068U-16 K B a
TUNER O C 0831 87-A12-069-040 CAP,E 22-25 SMG a
TUNER O C 0837 87-A12-022-080 C-CAP,U 0.22-16 Z F a
TUNER O C 0842 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER X C 0847 88-108-000-080 C-JUMPER,U a
TUNER X C 0848 88-108-000-080 C-JUMPER,U a
TUNER O C 0850 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0851 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0852 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0853 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0854 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
CZA-3
EZM
TUNER O C 0855 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0856 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0859 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER O C 0860 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0901 87-012-162-080 C-CAP,U 1P-50 C CH GRM a
TUNER O C 0902 87-012-165-080 C-CAP,U 3P-50 C CH a
TUNER O C 0903 87-012-164-080 C-CAP,U 2P-50 C CH a
TUNER O C 0904 86-ZA1-615-080 C-CAP,U 680P-25 J CH a
TUNER O C 0905 87-012-162-080 C-CAP,U 1P-50 C CH GRM a
TUNER O C 0906 87-012-172-080 C-CAP,U 10P-50 D CH a
TUNER O C 0907 87-012-166-080 C-CAP,U 4P-50 C CH a
TUNER O C 0908 87-012-165-080 C-CAP,U 3P-50 C CH a
TUNER O C 0909 86-ZA1-615-080 C-CAP,U 680P-25 J CH a
TUNER O C 0910 87-012-164-080 C-CAP,U 2P-50 C CH a
TUNER O C 0911 87-012-166-080 C-CAP,U 4P-50 C CH a
TUNER O C 0912 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0913 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0914 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0915 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0916 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
CZA-3
EZM
TUNER O C 0917 87-012-178-080 C-CAP,U 18P-50 J CH a
TUNER O C 0918 87-012-172-080 C-CAP,U 10P-50 D CH a
TUNER O C 0919 87-012-184-080 C-CAP,U 33P-50 J CH GRM a
TUNER O C 0920 87-012-184-080 C-CAP,U 33P-50 J CH GRM a
TUNER O C 0921 87-012-180-080 C-CAP,U 22P-50 J CH a
TUNER O C 0922 87-012-174-080 C-CAP,U 12P-50 J CH a
TUNER O C 0923 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0924 87-012-164-080 C-CAP,U 2P-50 C CH a
TUNER O C 0925 87-012-164-080 C-CAP,U 2P-50 C CH a
TUNER O C 0926 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0927 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0931 87-A12-319-080 C-CAP,U 0.1-25 K B a
TUNER O C 0932 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0933 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0934 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0935 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0936 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0937 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0938 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0939 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 15 –
Page 16
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CZA-3
EZM
TUNER O C 0942 87-012-168-080 C-CAP,U 6P-50 D CH GRM a
TUNER O C 0946 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0947 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0948 87-012-270-080 C-CAP,U 470P-50 K B GRM a
TUNER O C 0950 86-ZA1-616-080 C-CAP,U 0.01-50 K B (MUR) a
TUNER O C 0952 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0957 87-012-174-080 C-CAP,U 12P-50 J CH a
TUNER O C 0958 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0962 87-A10-262-080 C-CAP,U 1-10 Z F a
TUNER O C 0963 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER O C 0971 87-010-381-010 CAP,E 330-16 M SME a
TUNER O C 0972 87-A11-063-080 C-CAP,S 4.7-10 Z F a
TUNER O C 0973 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0974 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0976 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER O C 0979 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0981 87-A12-066-040 CAP,E 47-16 SMG a
TUNER O C 0982 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER O C 0983 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0984 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
CZA-3
EZM
TUNER O C 0985 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0987 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0988 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0989 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O C 0990 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0991 87-012-182-080 C-CAP,U 27P-50 J CH GRM a
TUNER O C 0992 87-012-172-080 C-CAP,U 10P-50 D CH a
TUNER O C 0993 87-012-274-080 C-CAP,U 1000P-50 K B GRM a
TUNER O C 0994 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0995 87-012-274-080 C-CAP,U 1000P-50 K B GRM a
TUNER O C 0996 87-012-195-080 C-CAP,U 100P-50 J CH GRM a
TUNER O C 0997 87-010-831-080 C-CAP,U 0.1-16 Z F a
TUNER O C 0998 87-A12-066-040 CAP,E 47-16 SMG a
TUNER O C 0999 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER O CF 0831 87-008-423-010 FLTR,CF SFE10.7MS3G-A a
TUNER O CF 0832 82-785-747-010 CF,MS2 GHY,R a
TUNER O CN 0991 87-A60-650-010 CONN,16P H GRY TUC-P16X-C1 a
TUNER S D 0801 87-020-465-080 DIODE,1SS133 a
TUNER S D 0803 87-020-465-080 DIODE,1SS133 a
TUNER X D 0896 88-100-000-010 PLATING-JW, 0.58 SN95 a
CZA-3
EZM
TUNER O D 0901 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a
TUNER O D 0902 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a
TUNER O D 0903 87-A41-048-040 C-VARI-CAP,HVM16-03 TL a
TUNER S D 0942 87-A40-270-080 C-DIODE,MC2838 a
TUNER X D 0944 88-108-000-080 C-JUMPER,U a
TUNER O D 0951 87-A40-799-040 C-VARI-CAP,KV1610S a
TUNER S D 0991 87-017-149-080 ZENER,HZS6A2L a
TUNER S D 0992 87-020-465-080 DIODE,1SS133 a
TUNER S IC 0801 87-A22-060-010 IC,LA1845N-A a
TUNER S IC 0991 87-A21-928-010 IC,LC72131D-N a
TUNER O J 0832 87-A61-823-010 TERMINAL,ANT PAL AJ-2073 a
TUNER O J 0940 87-A60-633-010 CONN,2P H 2.5MM JMT a
TUNER X JR 0783 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER S JW 0942 87-020-465-080 DIODE,1SS133 a
TUNER O JW 0959 87-A11-132-080 CAP,TC U 0.01-50 K B a
TUNER O L 0801 87-A50-694-010 COIL,FM-DET 2 (COILS) a
TUNER O L 0802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) a
TUNER O L 0811 87-005-847-080 COIL,2.2UH K CECS a
TUNER O L 0832 87-005-847-080 COIL,2.2UH K CECS a
TUNER O L 0901 86-ZA1-612-010 COIL,FM ANT/RF-1-Z a
CZA-3
EZM
TUNER O L 0902 86-ZA1-613-010 COIL,FM ANT/RF-2-Z a
TUNER O L 0903 87-003-098-080 COIL,2.2UH K LAL02 a
TUNER O L 0904 86-ZA1-612-010 COIL,FM ANT/RF-1-Z a
TUNER O L 0905 86-ZA1-613-010 COIL,FM ANT/RF-2-Z a
TUNER O L 0906 87-005-847-080 COIL,2.2UH K CECS a
TUNER O L 0907 86-ZA1-614-010 COIL,FM OSC-Z a
TUNER O L 0908 88-ZA1-624-010 COIL,FM IFT 7-6.2 (COILS) a
TUNER O L 0941 87-A50-020-010 COIL,ANT LW (COI) 252KHZ a
TUNER O L 0942 87-A50-019-010 COIL,OSC LW (COI) 856KHZ a
TUNER O L 0952 87-A50-754-010 COIL,MW ANT(3BLW) a
TUNER O L 0953 87-A50-755-010 COIL,MW OSC(3BLW) a
TUNER S Q 0835 89-327-143-080 C-TR,2SC2714O a
TUNER S Q 0836 87-A30-677-040 C-TR,SRA2207S a
TUNER S Q 0901 89-503-602-080 C-FET,2SK360E a
TUNER S Q 0902 87-A30-664-080 C-TR,2SC2620B a
TUNER S Q 0903 87-A30-664-080 C-TR,2SC2620B a
TUNER S Q 0904 87-A30-664-080 C-TR,2SC2620B a
TUNER S Q 0905 87-A30-664-080 C-TR,2SC2620B a
TUNER S Q 0948 87-A30-675-040 C-TR,2SD1306NE07TL a
TUNER S Q 0951 87-A30-074-080 C-TR,RT1P 141C a
– 16 –
Page 17
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CZA-3
EZM
TUNER S Q 0952 87-A30-675-040 C-TR,2SD1306NE07TL a
TUNER S Q 0953 89-503-602-080 C-FET,2SK360E a
TUNER S Q 0981 87-A30-494-080 TR,2SA1980G a
TUNER S Q 0982 87-A30-076-080 C-TR,2SC3052F a
TUNER S Q 0983 87-A30-076-080 C-TR,2SC3052F a
TUNER X R 0789 88-108-333-080 C-RES,U 33K-1/16W J a
TUNER O R 0790 87-012-286-080 C-CAP,U 0.01-25 K B GRM a
TUNER X R 0791 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0793 88-108-221-080 C-RES,U 220-1/16W J a
TUNER X R 0795 88-108-000-080 C-JUMPER,U a
TUNER X R 0801 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0802 88-108-223-080 C-RES,U 22K-1/16W J a
TUNER X R 0803 88-108-183-080 C-RES,U 18K-1/16W J a
TUNER X R 0804 88-108-000-080 C-JUMPER,U a
TUNER X R 0805 88-108-332-080 C-RES,U 3.3K-1/16W J a
TUNER X R 0806 88-108-682-080 C-RES,U 6.8K-1/16W J a
TUNER X R 0809 88-108-000-080 C-JUMPER,U a
TUNER X R 0810 88-108-000-080 C-JUMPER,U a
TUNER X R 0813 88-108-224-080 C-RES,U 220K-1/16W J a
TUNER X R 0814 88-108-222-080 C-RES,U 2.2K-1/16W J a
CZA-3
EZM
TUNER X R 0815 88-121-682-080 RES,6.8K-1/8W J a
TUNER X R 0816 88-108-472-080 C-RES,U 4.7K-1/16W J a
TUNER X R 0818 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0823 88-108-393-080 C-RES,U 39K-1/16W J a
TUNER X R 0826 88-108-223-080 C-RES,U 22K-1/16W J a
TUNER X R 0832 88-108-391-080 C-RES,U 390-1/16W J a
TUNER X R 0840 88-108-221-080 C-RES,U 220-1/16W J a
TUNER X R 0850 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0853 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0854 88-108-331-080 C-RES,U 330-1/16W J a
TUNER X R 0855 88-108-183-080 C-RES,U 18K-1/16W J a
TUNER X R 0856 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0857 88-108-181-080 C-RES,U 180-1/16W J a
TUNER X R 0858 88-108-271-080 C-RES,U 270-1/16W J a
TUNER X R 0860 88-121-101-080 RES,100-1/8W J a
TUNER X R 0890 88-108-474-080 C-RES,U 470K-1/16W J a
TUNER X R 0901 88-108-104-080 C-RES,U 100K-1/16W J a
TUNER X R 0902 88-108-104-080 C-RES,U 100K-1/16W J a
TUNER X R 0903 88-108-221-080 C-RES,U 220-1/16W J a
TUNER X R 0904 88-108-103-080 C-RES,U 10K-1/16W J a
CZA-3
EZM
TUNER X R 0905 88-108-221-080 C-RES,U 220-1/16W J a
TUNER X R 0906 88-108-564-080 C-RES,U 560K-1/16W J a
TUNER X R 0908 88-108-271-080 C-RES,U 270-1/16W J a
TUNER X R 0909 88-108-181-080 C-RES,U 180-1/16W J a
TUNER X R 0910 88-108-334-080 C-RES,U 330K-1/16W J a
TUNER X R 0911 88-108-181-080 C-RES,U 180-1/16W J a
TUNER X R 0912 88-108-104-080 C-RES,U 100K-1/16W J a
TUNER X R 0913 88-108-152-080 C-RES,U 1.5K-1/16W J a
TUNER X R 0914 88-108-472-080 C-RES,U 4.7K-1/16W J a
TUNER X R 0915 88-108-104-080 C-RES,U 100K-1/16W J a
TUNER X R 0916 88-108-470-080 C-RES,U 47-1/16W J a
TUNER X R 0944 88-108-101-080 C-RES,U 100-1/16W J a
TUNER X R 0945 88-108-104-080 C-RES,U 100K-1/16W J a
TUNER X R 0947 88-108-183-080 C-RES,U 18K-1/16W J a
TUNER X R 0948 88-108-472-080 C-RES,U 4.7K-1/16W J a
TUNER X R 0952 88-108-562-080 C-RES,U 5.6K-1/16W J a
TUNER X R 0954 88-108-222-080 C-RES,U 2.2K-1/16W J a
TUNER X R 0956 88-108-471-080 C-RES,U 470-1/16W J a
TUNER X R 0958 88-108-472-080 C-RES,U 4.7K-1/16W J a
TUNER X R 0959 88-108-103-080 C-RES,U 10K-1/16W J a
CZA-3
EZM
TUNER X R 0962 88-121-221-080 RES,220-1/8W J a
TUNER X R 0964 88-108-330-080 C-RES,U 33-1/16W J a
TUNER X R 0972 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0973 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0974 88-108-101-080 C-RES,U 100-1/16W J a
TUNER X R 0975 88-108-562-080 C-RES,U 5.6K-1/16W J a
TUNER X R 0976 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0977 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0978 88-108-681-080 C-RES,U 680-1/16W J a
TUNER X R 0980 88-108-684-080 C-RES,U 680K-1/16W J a
TUNER X R 0981 88-121-471-080 RES,470-1/8W J a
TUNER X R 0982 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0983 88-108-562-080 C-RES,U 5.6K-1/16W J a
TUNER X R 0984 88-108-562-080 C-RES,U 5.6K-1/16W J a
TUNER X R 0985 88-121-471-080 RES,470-1/8W J a
TUNER X R 0986 88-108-222-080 C-RES,U 2.2K-1/16W J a
TUNER X R 0988 88-108-000-080 C-JUMPER,U a
TUNER X R 0989 88-121-102-080 RES,1K-1/8W J a
TUNER X R 0990 88-108-563-080 C-RES,U 56K-1/16W J a
TUNER X R 0992 88-108-103-080 C-RES,U 10K-1/16W J a
– 17 –
Page 18
! = ! SAFTY PARTS
C = Components marked
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CZA-3
EZM
TUNER X R 0994 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0996 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X R 0997 88-108-154-080 C-RES,U 150K-1/16W J a
TUNER X R 0998 88-108-102-080 C-RES,U 1K-1/16W J a
TUNER X R 0999 88-108-103-080 C-RES,U 10K-1/16W J a
TUNER X SH 0901 8C-ZA3-604-010 SHLD-CASE,CZA-3 a
TUNER X SH 0902 8C-ZA3-619-010 SHLD-CASE,CZA-3 EZ P a
TUNER O TC 0942 87-A91-774-080 TRIMMER,PLY 30P 6.8X5.4 CDYL a
TUNER O X 0992 87-A70-306-010 VIB,XTAL 4.500MHZ CSA-309ST a
– 18 –
Page 19
ELECTRICAL PARTS LIST (3ZG – 3)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-3
E13NM
CD-LOAD O CON0006 87-099-210-010 CONN,5P H BLK 6216 a
CD-LOAD O M 0001 87-045-305-010 MOT,RF-500TB a
CD-LOAD O SW 0001 87-036-110-010 SW,MICRO SPPB62 a
CD-LOAD O SW 0002 87-036-110-010 SW,MICRO SPPB62 a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 19 –
Page 20
ELECTRICAL PARTS LIST (3ZG – 2)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-2
E3NM
CD-DRIVE O CON0003 87-A60-086-010 CONN,06P H 6216 a
CD-DRIVE O M 0020 87-045-358-010 MOT,RF-310TA 43 a
CD-DRIVE O M 0021 87-045-356-010 MOT,RF-310TA 30 a
CD-DRIVE O SW 0001 87-A90-042-010 SW,LEAF MSW-17310MVPO a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 20 –
Page 21
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
TRANSISTOR ILLUSTRATION
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
E C B
2SD655E
E C B
2N5551C
D
G
2SK360E
E C B
2SA1980G
B C E
2SB1342
2SD1933
E C B
2SA1318T
G D S
2SK2937
E C B
2SB1329(Q/R)
C
B
E
2SA1235F
2SB1218AQRS
2SC2620B
2SC2712GR
S
2SC2714O
2SC3052F
2SD1306NE07TL
2SD1819AQRS
RT1P 141C
SBT5401
SBT5551
SRA2202S
SRA2207S
– 21 –
Page 22
WIRING – 1 (MAIN)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 22 –
R
S
T
U
Page 23
SCHEMATIC DIAGRAM – 1 (MAIN : 1 / 3 / HP)
– 23 –
Page 24
SCHEMATIC DIAGRAM – 2 (MAIN : 2 / 3 <CD SECTION> / CD – DRIVE / CD – LOAD)
– 24 –
Page 25
SCHEMATIC DIAGRAM – 3 (MAIN : 3 / 3 <MICON SECTION>)
– 25 –
Page 26
WIRING – 2 (FRONT / KEY / HP)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 26 –
R
S
T
U
Page 27
SCHEMATIC DIAGRAM – 4 (FRONT / KEY)
– 27 –
Page 28
WIRING – 3 (AMP)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 28 –
R
S
T
U
Page 29
SCHEMATIC DIAGRAM – 5 (AMP)
– 29 –
Page 30
WIRING – 4 (PT)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 30 –
R
S
T
U
Page 31
SCHEMATIC DIAGRAM – 6 (PT)
– 31 –
Page 32
WIRING – 5 (TUNER)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 32 –
R
S
T
U
Page 33
SCHEMATIC DIAGRAM – 7 (TUNER)
– 33 –
Page 34
WIRING – 6 (CD – DRIVE / CD – LOAD)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
– 34 –
R
S
T
U
Page 35
FL (HNA – 10SM19) GRID ASSIGNMENT / ANODE CONNECTION / PIN CONNECTION
GRID ASSIGNMENT
ANODE CONNECTION
PIN CONNECTION
– 35 –
Page 36
IC BLOCK DIAGRAM
– 36 –
Page 37
– 37 –
Page 38
IC DESCRIPTION
IC, LC876748A-5Z30
Pin No. Pin Name I/O Description
1 O-CD DATA O CD IC control data output.
2 O-CD ON O CD ON/OFF control output. (Not used)
3 O-CD OPEN O CD tray open signal output.
4 O-CD CLOSE O CD tray close signal output.
5 O-PLL CE O PLL IC control chip enable output.
6 O-PLL CLK O PLL IC control clock output.
7 O-PLL DATA O PLL IC control data output.
8 I-RDS DATA I RDS data input. <EZ only>
9 NC – Not connected.
10 O-CLKSFT O MICON clock shift output.
11 I-RESET I Reset input.
12 I-TUSIG I TUNER_SD detect input. <EZ only>
13 I-CD SW I CD switch input.
14 VSS1 – GND.
15 CF1 I
16 CF2 O
9.43MHz oscillator circuit.
17 VDD1 – Power supply.
18 I-HOLD I Power failure detection input.
19 I-LEVEL I Signal level input. (Not used)
20 I-STEREO I Tuner stereo detect input.
21 I-TUNE/IFC I Tune IF count serial data input.
22 I-ENC VOL I Rotary encoder VOLUME input.
23 I-ENC TRE I Rotary encoder TREBLE input.
24 I-ENC BASS I Rotary encoder BASS input.
25 ~ 26 I-KEY2 ~ I-KEY1 I Key input.
27 I-TMBASE I Reference clock input for watch.
28 I-RDS CLK I RDS clock input. <EZ only>
29 I-REM I System remote control signal input.
30 G11 O FL grid output G11. (Not used)
31 ~ 40 G10 ~ G1 O FL grid output G10 ~ G1.
41 ~ 45 P20 ~ P16 O FL segment output P20 ~ P16.
46 VDD3 – Power supply.
47 ~ 50 P15 ~ P12 O FL segment output P15 ~ P12.
51 FIXO – Connected to GND.
52 ~ 62 P11 ~ P1 O FL segment output P11 ~ P1.
63 ~ 65 NC – Not connected.
66 I-TU SEL1 I
67 I-TU SEL2 I
68 I-TU SEL3 I
SEL1 SEL2 SEL3
U/LH H H H
DHHL
HR H L L
KHLH
EZ L H H
VLLH
– 38 –
Page 39
Pin No. Pin Name I/O Description
69 I-DEMO OFF I Initial DEMO OFF/ON. (Not used)
70 I-ECO OFF I Initial ECO OFF/ON. (Connected to pull-down resistor)
71 NC – Not connected.
72 VDD4 – Power supply.
73 ~ 84 NC – Not connected.
85 O-TU ON O Tuner ON/OFF control output.
86 O-FUNC CLK O FUNCTION IC control clock output.
87 O-FUNC DATA O FUNCTION IC control data output.
88 O-POWER O System power supply ON/OFF output.
89 VSS2 – GND.
90 VDD2 – Power supply.
91 O-MUTE O Audio mute ON/OFF control output. (Not used)
92 O-LMUTE O Line mute ON/OFF control output.
93 O-STBY O Standby LED ON/OFF control output.
94 ~ 95 NC – Not connected.
96 I-CD DRF I Detect CD RF level input.
97 I-CD WRQ I Standby for CD sub-code Q output input.
98 I-CD SUBQ I CD IC data input.
99 O-CD CE O CD IC control chip enable output.
100 O-CD CLK O CD IC control clock output.
– 39 –
Page 40
IC, LC78646E
Pin No. Pin Name I/O Description
1 SLCO O Slice level control output.
2 SLCIST I SLCO output current adjustment resistor connection pin.
3 EFMIN I RF signal input pin.
4 RF O RF monitor pin.
5 RFVDD – RF power supply pin.
6 RFVSS – RF ground pin. (Connected to 0V)
7 FIN1 I A+C signal input pin.
8 FIN2 I B+D signal input pin.
9 TIN1 I E signal input pin.
10 TIN2 I F signal input pin.
11 VREF O VREF voltage output pin.
12 REF1 I Reference voltage setting pin.
13 FE O FE signal monitor pin.
14 TEC O TE signal low pass filter capacitor connection pin.
15 TE O TE signal monitor pin. (Not used)
16 RFMON O RF internal signal monitor pin. (Not used)
17 JITTC – Jitter detection capacitor connection pin.
18 ADAVDD – Servo A/D, D/A supply pin.
19 ADAVSS – Servo A/D, D/A ground pin. (Connected to 0V)
20 TDO O Tracking control output pin. D/A output.
21 FDO O Focus control output pin. D/A output.
22 SPDO O Spindle control output pin. D/A output.
23 SLDO O Sled control output pin. D/A output.
24 GPDAC O Servo D/A general purpose output pin. (Not used)
25 CONT4-DRVMUTE I/O General purpose input/output pin 4. (Used as a CD driver mute pin)
26 CONT5 I/O General purpose input/output pin 5. (Not used)
27 SBCK/CONT6-SWIL I/O
28 SBCK/FG I
29 DEFECT O Defect pin. (Not used)
30 V/P O
Sub-code read clock input pin / General purpose input/output pin 6.
(Used as a CD pickup inside limit switch pin)
Sub-code read clock input pin / FG signal input pin/external emphasis setting pin.
Set to command pin function. (Connected to 0V)
Rough servo/phase control automatic switching monitor output pin.
"H" for rough servo and "L" for phase servo. (Not used)
Synchronization signal detection output pin.
31 FSEQ O Outputs a high level when the synchronization signal detected from the EFM signal and the
internally generated synchronization signal agree. (Not used)
32 ~ 36 MONI1 ~ MONI5 O Internal signal monitor pin 1 ~ 5. (Not used)
37 VSS – Digital ground pin. (Connected to 0V)
38 VDD – Digital power supply pin.
39 DOUT O Digital OUT output pin.
40 TEST I Test input pin. (Connected to 0V)
– 40 –
Page 41
Pin No. Pin Name I/O Description
41 LVDD – Left channel power supply pin.
42 LCHO O Left channel output pin.
43 LVSS – Left channel ground pin. (Connected to 0V)
44 RVSS – Right channel ground pin. (Connected to 0V)
45 RCHO O Right channel output pin.
46 RVDD – Right channel power supply pin.
47 XVDD – Crystal oscillator power supply pin.
48 XOUT O
49 XIN I
50 FSX/16MIN I/O 7.35kHz synchronization signal output pin / DF, DAC external clock input pin. (Not used)
51 XVSS – Crystal oscillator ground pin. (Connected to 0V)
52 C2F O C2 flag output pin. (Not used)
53 EFLG O C1, C2 error correction monitor pin. (Not used)
54 16MOUT O 16.9344MHz output pin. (Not used)
55 ASLRCK I Left/Right clock input pin during anti-shock mode. (Connected to 0V)
56 ASDACK I Bit clock input pin during anti-shock mode. (Connected to 0V)
57 ASDFIN I Left/Right channel data input pin during anti-shock mode. (Connected to 0V)
58 LRSY O Left/Right clock output pin. (Not used)
59 DATACK O Bit clock output pin. (Not used)
60 DATA O Left/Right channel data output pin. (Not used)
61 CE I Chip enable signal input pin.
62 CL I Data transfer clock input pin.
63 DI I Data input pin.
64 DO O Data output pin. (Nch open drain output)
65 WRQ O Interruption signal output pin.
66 RES I Reset input pin. This pin must be set low briefly after power is first applied.
Connections for a 16.9344MHz crystal oscillator pin.
67 DRF O Focus ON detect pin.
68 VDD5 – Microprocessor interface power supply pin.
69 VSS – Digital ground pin. (Connected to 0V)
70 ~ 72 CONT3 ~ CONT1 I/O General purpose input/output pin 3 ~ 1.
73 PDO1 O Phase comparison output pin 1 to control built-in VCO.
74 PDO2 O Phase comparison output pin 2 to control built-in VCO.
75 VVSS – Built-in VCO ground pin. (Connected to 0V)
76 PCKIST I Resistor connection pin to set current for PDO1 and PDO2 outputs.
77 VVDD – Built-in VCO power supply pin.
78 FR I Resistor connection pin to set the frequency range of built-in VCO.
79 LDS I Laser power detection signal input pin.
80 LDD O Laser power control signal output pin.
– 41 –
Page 42
IC, LC72131D-N
Pin No. Pin Name I/O Description
1 X-IN I
22 X-OUT O
2 NC – Not connected.
3 CE I To enable the IC. Active "H".
A crystal oscillator (4.5MHz) is connected between these pins.
4DII
5 CL I To clock in the data DI.
6 DO O Digital data output to CPU (LC876748A-5Z30).
7 T-BASE O Outputs a reference clock signal (8Hz) for the clock.
8 MONO / BEAT O Outputs "H" when MONO / BEAT is switched.
9 FM / SW O
10 MW / SW O
11 IF-MUTE O To control internal counter.
12 IF-IN I General purpose counter input.
13 TUNE I Receives "L" when station is tuned.
14 NC – Not connected.
Digital data input from CPU (LC876748A-5Z30) when relevant key is operated.
Active "H".
Output "L" or "H" as follows:
2 BAND 3 BAND 3 BAND
AM FM LW MW FM MW SW FM
HLHHLHLL
Outputs "L" or "H" as follows:
2 BAND 3 BAND 3 BAND
AM FM LW MW FM MW SW FM
LLHLLLHL
15 AM-IN I Receives the AM local oscillator frequency signal.
16 FM-IN I Receives the FM local oscillator frequency signal.
17 VDD – Supply power to IC (+5V).
18 PD O PLL charge pump output.
19 A-IN I
20 A-OUT O
21 VSS – Ground.
The MOS transistor used for PLL active low pass filter.
– 42 –
Page 43
ADJUSTMENT (TUNER / MAIN)
TUNER ADJUSTMENT
TUNER C. B (PARTS SIDE)
L952
L953
L941
L942
TC942
L902
L901
L905
L904
L907
IC991
L802
CN991
⑦
②
⑧
IC801
⑥
④
⑨
TUNER C. B (PATTERN SIDE)
CN991
TP9 (12pin)
TP1 (24pin)
1. CLOCK CHECK
Requirement
Measuring equipment: Frequency counter
Test point: TP1 (CLK), GND
(1) Adjust the reception frequency of the main unit to 1710kHz.
(2) Check that the test point frequency is 2160kHz±0.045kHz.
2. VT ADJUSTMENT (LW)
Requirement
Measuring equipment: Digital multi-meter
Test point: TP4 (R962), GND
Adjustment point: L942
(1) Adjust the reception frequency of the main unit to 144kHz.
(2) Adjust L942 until the test point voltage (VT) is 1.3V±0.05V.
3. VT CHECK (MW)
Requirement
Measuring equipment: Digital multi-meter
Test point: TP4 (R962), GND
(1) Adjust the reception frequency of the main unit to 531kHz.
(2) Check that the test point (VT) voltage is about 0.5V.
(3) Adjust the reception frequency of the main unit to 1602kHz.
(4) Check that the test point (VT) voltage is below 8.0V.
4. VT ADJUSTMENT (FM)
Requirement
Measuring equipment: Digital multi-meter
Test point: TP4 (R962), GND
Adjustment point: L907
(1) Adjust the reception frequency of the main unit to 108.0MHz.
(2) Adjust L907 until the test point voltage (VT) is 7.0V±0.1V.
(3) Adjust the reception frequency of the main unit to 87.5MHz.
(4) Check that the test point (VT) voltage is about 0.5V.
– 43 –
GND (8pin)
TP8 (11pin)
TP2
IC801
TP3
R815
R962
TP4
①②③④
⑥⑦⑧⑨
⑥⑦⑧⑨
①
②③④
⑤
FREQUENCY COUNTER
Hz
TP
GND
DIGITAL MULTIMETER
V
TP
GND
DIGITAL MU LTIMETE R
V
TP
GND
DIGITAL MULTIMETER
V
TP
GND
Page 44
5. DC BALANCE CHECK (FM)
Requirement
Measuring equipment: Digital multi-meter
Test point: TP2, 3
(1) Adjust the reception frequency of the main unit to 98.0MHz.
(2) Check that the test point voltage difference between TP2 and TP3 is
0mV±500mV.
<LW / MW ADJUSTMENT>
For LW / MW adjustment, do wiring and connection as in the following.
60cm
DIGITAL MU LTIMETE R
V
TP
GND
Standerd Signal Generaor
6. IF ADJUSTMENT (MW)
Requirement
Measuring equipment: Oscilloscope or Millivoltmeter
Test point: TP8(Lch), TP9(Rch), GND
Adjustment point: L802
(1) Adjust the setting of Standard Signal Generator (hereinafter S.S.G.) to 999kHz
of 30% variation.
(2) Adjust the receiving frequency of the main unit at 999kHz.
(3) While looking at the waveform on the oscilloscope, reduce the output level all the
way (till a certain degree of is monitored through the oscilloscope).
(4) Adjust L802 until the waveform of the oscilloscope reaches the maximum.
7. TRACKING ADJUSTMENT (MW)
Requirement
Measuring equipment: Millivoltmeter
Test point: TP8(Lch), TP9(Rch), GND
Adjustment point: L952, L953
(1) Adjust the S.S.G. setting to 999kHz of 30% variation and reduce the output level
all the way (till a certain degree of is monitored through the oscilloscope).
(2) Adjust the reception frequency of the main unit to 999kHz.
(3) Adjust L952 until the value of the millivoltmeter reaches the maximum.
(4) Adjust the S.S.G. setting to 603kHz of 30% variation and reduce the output level
all the way (till a certain degree of is monitored through the oscilloscope).
(5) Adjust the reception frequency of the main unit to 603kHz.
(6) Adjust L953 until the value of the milivoltmeter reaches the maximum.
(7) Repeat the adjustment 2 or 3 times from step 1 to 6 above.
– 44 –
SET
Lch
Rch
GND
TP
Connect to the respective
measuring equipment
OSCILLOSCOPE
CH1 CH2
Lch
Rch
GND
AC MILLIVOLTMETER
TP8
GND
TP9
CH1
GND
GND
CH2
Page 45
8. TRACKING ADJUSTMENT (LW)
Requirement
Measuring equipment: Millivoltmeter
Test point: TP8(Lch), TP9(Rch), GND
Adjustment point: L941, TC942
(1) Adjust the S.S.G. setting to 144kHz of 30% variation and reduce the output level
all the way (till a certain degree of is monitored through the oscilloscope).
(2) Adjust the reception frequency of the main unit to 144kHz.
(3) Adjust L941 until the value of the millivoltmeter reaches the maximum.
(4) Adjust the S.S.G. setting to 290kHz of 30% variation and reduce the output level
all the way (till a certain degree of is monitored through the oscilloscope).
(5) Adjust the reception frequency of the main unit to 290kHz.
(6) Adjust TC942 until the value of the milivoltmeter reaches the maximum.
(7) Repeat the adjustment 2 or 3 times from step 1 to 6 above.
<FM ADJUSTMENT>
For adjusting FM, do wiring function and connection as in the following.
AC MILLIVOLTMETER
TP8
GND
TP9
CH1
CH2
GND
Standerd Signal G eneraor
9. TRACKING ADJUSTMENT (FM)
Requirement
Measuring equipment: Millivoltmeter
Test point: TP8(Lch), TP9(Rch), GND
Adjustment point: L905, L904, L902, L901
(1) Adjust the S.S.G. setting to 144kHz of 30% variation and reduce the output level
all the way (till a certain degree of is monitored through the oscilloscope).
(2) Adjust L905 > L904 > L902 > L901 until the value of the milivoltmeter reaches the
maximum.
(3) Adjust L901 > L902 > L904 > L905 until the value of the milivoltmeter reaches the maximum.
(4) Repeat the adjustment 2 or 3 times from step 2 to 3 above.
– 45 –
SET
TP
Lch
Rch
GND
Connect to the respective
measuring equipment
AC MILLIVOLTMETER
CH2
TP8
GND
TP9
CH1
GND
Page 46
CLOCK ADJUSTMENT AND CD CHECK
MAIN C. B (PATTERN SIDE)
GND
IC401
CLK
Q301
R315
IC301
TE
FE
VREF
RF
L401
1. CLOCK ADJUSTMENT
Requirement
Test point: CLK, GND
Adjustment point: L401
1) While pressing and holding down the POWER button and the TUNER / BAND button, insert the
AC plug to outlet.
2) Adjust L401 so that the oscilloscope indicates the frequency within 347.661Hz〜348.357Hz.
CD CHECK
Perform the adjustments after the main unit enters the test mode.
Place the CD mechanism on level ground.
Equipment and tools required.
Measuring equipment
Digital multi-meter
Jitter meter (KIKUSUI 6235)
Test disc: TCD-782
ATD-001
2. RF WAVEFORM CHECK
1) Connect oscilloscope to the test point RF and VREF.
2) Play back the 2
nd
track of TCD-782.
3) Check that the RF waveform has the maximum amplitude and the center
of the wedge waveform has the clear blank.
EYE PATTERN
must be CLEAR and MAX
VOLT / DIV: 500mV
TIME / DIV: 0.2µs
Approx.
1.8 ±0.3Vp.p
– 46 –
①
④
②③④
②③
⑥
OSCILLOSCOPE
OUTPUT
RF
VREF
Page 47
3. JITTER CHECK
1) While oscilloscope is kept connected in the same test point as in
step2. RF WAVEFORM CHECK, connect the output terminal of
an oscilloscope to the input terminal of the jitter meter.
2) Set the VOLT range selector of oscilloscope to 500mV range or
below.
3) Play back 2
4) Check that jitter meter indicates 28.0ns or less.
nd
track of TCD-782.
VREF
4. TRACKING BALANCE CHECK
1) Connect the TE and VREF to the oscilloscope.
2) Playback the second track of TCD-782 and press the PAUSE button.
3) Check that the traverse waveforms of oscilloscope are up and down symmetrical.
A
0V
B
A=B
VOLT / DIV: 100mV
TIME / DIV: 1ms
5. PLAYABILITY CHECK
1) Play back the 3
rd
, 8th and 13th track of ATD-001. Check that the noise does not occur sound skipping does not
occur.
6. LASER CURRENT CHECK
*Do not perform this measurement unless the laser is suspected to be defective.
1) Connect digital multi-meter across the resistor R315 (3.3ohm).
2) Play back the TCD-782 and check the DC voltage value on the digital multi-meter.
3) Calculate the laser current (Iop) by dividing the DC voltage across R315 by the
resistor value (R315= 3.3ohm).
OSCILLOSCOPE
OUTPUT
RF
JITTER METER
INP UT
OSCILLOSCOPE
TE
VREF
DIGITAL MULTIMETER
R315
R315
ns
OUTPUT
V
Check that the laser current (Iop) is SPEC value ±10%.
– 47 –
EXAMPLE
KSS -213F
05Y93
DA372
SPEC VALUE
37.2mA
Page 48
CD TEST MODE
1. How to Start the CD Test Mode
While pressing the CD PLAY button, insert the AC plug to the power outlet.
When the test mode is started, the all indicators light is displayed.
2. How to Exit the CD Test Mode
Press the POWER button, push other FUNCTION button or disconnect the AC plug.
3. Function Descriptions and Application of the CD Test Mode
No.
1
2
3
4
5
6
Mode
Start
mode
Search
mode
Play
mode
Traverse
mode
Sled
mode
Spindle
mode
Operation
STOP
button
Play
button
PAUSE
button
FF button
RWD
button
ENTER
or
SET button
Display
All indicators light
READING
Normal
Normal
CD TEST
CD TEST
All indicators light
Function
• All FL indicators light
• LD illuminates all the time
• Focus search continuous
operations *1
• Spindle motor continuous kick
• Normal playback
• If TOC cannot be read,
focus search is continued
• Tracking servo OFF/ON
• Each time PAUSE button is
pressed, the tracking servo
repeats turning OFF/ON
• Pickup moves to the inner
circumference *2
At the same time, lens kicks to
the inner circumference
• Pickup moves to the outer
circumference *2
At the same time, lens kicks to
the outer circumference
• The spindle motor rotates
forward (rough speed) by
pressing the button and rotates
backward by pressing one more
time and stops by pressing again
Checking item
• FL check
• Microprocessor check
• APC circuit check
• Laser current measurement
• Focus search waveform check
• Focus error waveform check
(DRF in the search mode is ignored)
• Each servo circuit is checked
• DRF check
• Tracking balance check
• Sled circuit check
• Tracking circuit check
• Mechanism operation check
• Pickup check
• Spindle circuit
• Spindle motor
1:The driver IC heats up and the protection circuit starts working when the focus search is continued for 10 minutes or longer.
*
There can be a case that operations can not be performed correctly.
In such a case, turn off the main power. After cooling down the machine, restart the machine.
2:Be careful not to damage the gear because the sled motor rotates while the FF or RWD button is being pressed even if the
*
pick-up is located in the innermost track or the outermost track.
– 48 –
Page 49
MECHANICAL EXPLODED VIEW
38
H
12
H
10
11
5
4
6
C
A
3
2
18
1
16
17
9
41
8
A
H
14
13
15
H
B
40
19
31
21
I
J
H
B
7
E
F
E
E
32 39
D
21
33
H
34
35
H
22
23
24
J
I
G
36
G
42
37
17
H
H
20
– 49 –
30
29
28
25
B
F
H
26
H
27
Page 50
MECHANICAL PARTS LIST
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
O MC1001 8C-CL4-017-010 WINDOW,ASSY DISPLAY K a .
O MC1001 8C-CL4-006-010 WINDOW,ASSY DISPLAY . b
X MC1001a 8C-CL4-018-010 WINDOW,DISPLAY K a .
X MC1001a 8C-CL4-005-010 WINDOW,DISPLAY . b
X MC1001b 8C-CL4-209-010 SH,ADH WINDOW a b
O MC1002 8C-CL4-008-010 KNOB,RTRY BT a b
O MC1003 8Z-CC3-007-010 BADGE,AIWA 27.5 ABS SIL a b
O MC1004 8C-CL4-010-010 REFLECTOR,POWER a b
O MC1005 8C-CL4-009-010 KEY,POWER a b
X MC1006 8C-CL4-615-010 PWB,HP a b
! O MC1007 8B-NF9-665-010 PT,SUB BNF E (TAM) a b
X MC1008 8C-CL4-613-010 PWB,KEY a b
S MC1009 8C-CL4-630-010 FL,HNA-10SM19 a b
X MC1010 8C-CL4-202-010 GUIDE,FL a b
X MC1011 8C-CL4-612-010 PWB,FRONT a b
O MC1012 88-913-221-110 FF-CABLE, 13P 1.25 220MM a b
O MC1013 8C-CL4-011-010 KEY,PLAY a b
X MC1014 M8-3ZG-38K-030 3ZG-3 E13NM a b
O MC1015 8C-CL4-012-010 KEY,SKIP a b
O MC1016 8C-CL4-015-010 CABI,FR K a .
CX-LEM60 CX-LEM61
KSM EZSM
O MC1016 8C-CL4-001-010 CABI,FR EZ . b
X MC1017 8B-NF9-204-010 CUSH, 11-8.5-2 a b
O MC1018 8C-CL4-007-010 KNOB,RTRY VOL a b
O MC1019 8C-CL4-004-010 PANEL,TRAY CD a b
X MC1020 8C-CL4-201-010 CHAS,MAIN a b
X MC1021 87-064-080-010 BINDER,WIRE a b
O MC1022 87-003-317-010 F-BEAD,15-25-15 E2515MRT a b
O MC1023 87-085-185-010 BUSHING,AC CORD(E) CM-22B a b
! O MC1024 8A-MTM-649-010 AC CORD ASSY,EKH BLK a b
X MC1025 8C-CL4-208-010 HT-SINK,SUB B a b
X MC1026 A8-CZA-395-030 CZA-3 EZM a b
X MC1027 8C-CL4-611-010 PWB,MAIN a b
O MC1028 8C-CL4-652-010 FF-CABLE,16P 1.00 a b
O MC1029 88-906-101-110 FF-CABLE, 6P 1.25 a b
O MC1030 88-905-231-110 FF-CABLE, 5P 1.25 230MM a b
X MC1031 8C-CL4-620-110 PWB,PT 4M a b
! O MC1032 8C-CL4-640-010 PT,CCL-4 EZ a b
X MC1033 8C-CL4-203-010 HLDR,PWB PT a b
X MC1034 8C-CL4-614-010 PWB,AMP a b
X MC1035 8C-CL4-207-010 HT-SINK,SUB A a b
CX-LEM60 CX-LEM61
KSM EZSM
X MC1036 8C-CL4-204-010 HT-SINK,ASSY MAIN a b
X MC1036a 8C-CL4-206-010 HT-SINK,FIN a b
X MC1036b 8C-CL4-205-010 HT-SINK,MAIN a b
O MC1037 8C-CL4-002-010 CABI,REAR EZ a b
O MC1038 8C-CL4-003-010 PANEL,TOP a b
X MC1039 8A-CY4-641-010 TUBE,UL 16.0-80 BLK a b
O MC1040 87-064-185-010 HLDR,WIRE PVC 0.5 a b
X MC1041 8C-CL4-211-010 CUSH,G 6.5-6.5-6.5 W/ADH a b
! O MC1042 87-099-811-010 PLUG,ADPTR CONV(K) a .
O MC1A 87-721-096-410 QT2+3-10 W/O SLOT a b
O MC1B 87-067-579-010 BVT2+3-8 W/O SLOT a b
O MC1C 88-AR1-217-010 S-SCREW,BFT2+3-8 a b
O MC1D 87-B10-314-010 BVIT3B+3-6 R W/O a b
O MC1E 87-B10-318-010 BVIT3C+4-8 R W/O a b
O MC1F 87-NF4-224-010 S-SCREW,IT3B+3-8 CU a b
O MC1G 87-B10-315-010 BVIT3B+3-8 R W/O a b
O MC1H 87-067-703-010 BVT2+3-10 W/0 SL0T a b
O MC1I 87-067-660-010 BVT2+3-8 W/0 SL0T BLK a b
O MC1J 86-NF8-223-010 W-P,4.15-6.9-0.25 W/ADH a b
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 50 –
Page 51
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue L L Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange PT Transparent Pink
LA Aqua Blue GL Light Green HT Transparent Gray
HM Metallic Gray NH Champagne Gold M Wood Pattern
– 51 –
Page 52
CD MECHANISM EXPLODED VIEW 1 / 2 <3ZG – 3 E13NM>
9
C
F
18
15
16
14
18
F
20
b
5
7
B
E
8
2
13
a
11
10
4
6
12
D
3
17
19
b
a
A
1
– 52 –
Page 53
CD MECHANISM PARTS LIST 1 / 2 <3ZG – 3 E13NM>
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-3
E13NM
O SC1001 83-ZG3-224-510 HLDR M2 a
O SC1002 83-ZG3-228-710 CHAS,L6 a
O SC1003 83-ZG3-208-010 PULLEY,MOTOR a
O SC1004 83-ZG3-213-010 LVR,SW a
O SC1005 83-ZG3-209-710 CAM,SLIDE a
O SC1006 83-ZG3-207-010 GEAR,TRAY a
O SC1007 83-ZG3-204-210 GEAR,C a
O SC1008 83-ZG3-205-010 GEAR,D a
O SC1009 83-ZG3-211-010 PLATE,DISC a
O SC1010 83-ZG3-220-210 GEAR,PULLEY 2 a
O SC1011 83-ZG3-214-010 BELT,L a
O SC1012 83-ZG3-231-310 TRAY,CD 3 a
O SC1013 83-ZG3-230-110 HLDR,CHUCK 2 a
O SC1014 83-ZG3-604-010 RING,MAG 2 a
O SC1015 86-ZG1-238-010 HLDR,MAGNET 6ZG N a
O SC1016 86-ZG1-239-110 PLATE,DISC PC a
O SC1017 87-045-305-010 MOT,RF-500TB a
O SC1018 83-ZG3-225-010 CUSH-G,MAIN A a
X SC1019 83-ZG3-603-010 PWB,LOAD-A 27M a
X SC1020 M8-3ZG-275-030 3ZG-2 E3NM a
3ZG-3
E13NM
O SC1A 87-067-945-110 VFT2+3-12 (F10) a
O SC1B 87-251-071-410 U+2.6-4 a
O SC1C 83-ZG3-235-010 VFT2+2.6-8 a
O SC1D 87-352-075-210 VT2+2.6-10 a
O SC1E 83-ZG3-217-010 S-SCREW,GEAR D a
O SC1F 81-ZG1-254-010 S-SCREW,MECH HLDR a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 53 –
Page 54
CD MECHANISM EXPLODED VIEW 2 / 2 <3ZG – 2 E3NM>
7
8
2
1
A
6
3
4
10
9
5
– 54 –
Page 55
CD MECHANISM PARTS LIST 2 / 2 <3ZG – 2 E3NM>
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-2
E3NM
O 001 83-ZG2-243-410 CHAS ASSY,SHT a
X 001a 83-ZG2-244-310 CHAS,SHT a
X 001b 83-ZG2-249-110 TURN TABLE,C3 a
X 001c 83-ZG2-241-110 PLATE,C2 a
O 002 87-A90-836-010 PICKUP,KSS-213F a
O 003 83-ZG2-235-010 GEAR,A3 a
O 004 83-ZG2-236-010 GEAR,MOTOR 3 a
O 005 83-ZG2-205-210 GEAR,B a
O 006 83-ZG2-253-110 SHAFT,SLIDE 5 a
O 007 83-ZG2-245-510 LEVER,SHUTTER a
O 008 83-ZG2-250-210 SPR-E,SHT 2 a
X 009 83-ZG2-609-010 PWB,DRIVE-G 21M a
O 010 87-045-356-010 MOT,RF-310TA 30 a
O A 87-261-032-210 V+2-3 a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 55 –
Page 56
ACCESSORIES PARTS LIST
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
PRINTED DU O 1 8C-CL4-905-010 IB,K(E)M XR-EM60 a .
PRINTED DU O 1 8C-CL4-906-010 IB,EZ(9L)M XR-EM61 . b
ACCESSORY O 2 8C-CL2-701-010 RC UNIT,RC-CAS04 a b
ACCESSORY O 3 87-A92-346-010 ANT,WIRE FM(FASTEN) a b
ACCESSORY O 4 87-006-226-010 ANT,LOOP AM a b
ELECTRICAL ! O 5 87-099-811-010 PLUG,ADPTR CONV(K) a .
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 56 –
Page 57
OTHER PARTS LIST (CX – LEM60 / CX – LEM61)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CX-LEM60 CX-LEM61
KSM EZSM
LBL,POP X 8C-CL4-970-010 LBL,POP K a b
PACKING DU X 87-B40-093-010 BAG,PV 0.04-450-650 PL a b
PACKING DU X 8C-CL4-853-010 BOX,A a b
PACKING DU X 8C-CL4-851-010 CUSHION,FRONT AEM a b
PACKING DU X 8C-CL4-852-010 CUSHION,REAR AEM a b
PACKING DU X 93-324-066-010 SH,FOAMED-MAT 0.31-500-300 a b
PACKING DU X 87-B40-334-010 BAG,PV 0.03-120-400 a .
PRINTED DU X 87-B40-085-010 BAG,PV 0.04-200-350 PL a b
PRINTED DU X 87-B50-079-010 LIST,FACILITY(B)-0007 a b
PRINTED DU X 87-056-168-010 SH,CAUTION INF-WARR(EC) a b
X 87-069-033-010 CABLE,TIE a b
X 87-B40-281-010 LBL,BAR-CODE A 35X8 a b
X 87-057-995-010 LBL,CAUTION EFSD a b
X 87-057-961-010 LBL,CAUTION TRIANGLE a b
X 8C-CL4-210-010 SH,CHAS W/ADH a b
X 8C-CL4-013-010 SH,FL a b
X 80-XV1-218-010 CUSH-S,PWB a b
X 88-121-123-080 RES,12K-1/8W J a b
X 8C-CL4-021-010 LBL,SPEC KM a .
X 8C-CL4-020-010 LBL,SPEC EZM . b
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 57 –
Page 58
OTHER PARTS LIST (CZA – 3)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
CZA-3
EZM
ASSY CODE X A8-CZA-395-030 CZA-3 EZM a
TUNER X 8C-ZA3-601-010 PWB,TUNER KEZ 6M a
TUNER X 8C-ZA3-618-010 SHLD-CASE,CZA-3 EZ S a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 58 –
Page 59
OTHER PARTS LIST (3ZG – 3)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-3
E13NM
ASSY CODE X M8-3ZG-38K-030 3ZG-3 E13NM a
ELECT X 81-MX4-700-010 SHIELD CORE,MOT S a
PACKING X 83-ZG3-599-010 BAG,PV ANTI 390X265 a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 59 –
Page 60
OTHER PARTS LIST (3ZG – 2)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
3ZG-2
E3NM
ASSY CODE X M8-3ZG-275-030 3ZG-2 E3NM a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 60 –
Page 61
GENERAL SPEAKER DISASSEMBLY INSTRUCTIONS (FOR REFERENCE)
Type.1
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Remove the screws of each speaker
unit and then remove the speaker units.
Type.2
Remove the grill frame and four pieces of rubber caps by pulling
out with a flat-bladed screwdriver. Remove the screws from hole
where installed rubber caps. Insert a flat-bladed screwdriver into
the position indicated by the arrows and remove the panel. Remove the screws of each speaker unit and then remove the speaker
units.
Type.4
TOOLS
1 Plastic head hammer
2 (() flat head screwdriver
3 Cut chisel
12 3
How to Remove the PANEL, FR
1. Insert the (( ) flat head screwdriver tip into the gap
between the PANEL, FR and the PANEL, SPKR. Tap the
head of the (() flat head screwdriver with the plastic
hammer head, and create the clearance as shown in Fig-1.
2. Insert the cut chisel in the clearance, and tap the head of
the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.
Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counterclockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise
direction until "click" sound comes out.
3. Place the speaker horizontally. Tap head of the cut chisel
with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.
Fig-1 Fig-2
How to Attach the PANEL, FR
Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.
– 61 –
Fig-3
Page 62
SPEAKER PARTS LIST (SX – LEM60)
! = ! SAFTY PARTS
C = Components marked
UNIT-NAME ! C REF-NO PARTS-NO PARTS-NAME SUFFIX&MODEL
SX-SLEM60
YJMN
OTHERS O 1 8A-CJ5-415-010 TERMINAL, a
OTHERS O 2 8B-CP5-610-010 CORD,SPKR a
OTHERS X 3 8B-CPX-001-010 TUBE,40 a
OTHERS X 4 8B-CPX-005-010 GRILLE,FRAME a
OTHERS X 5 8B-CPX-009-010 CUSHION,FELT a
OTHERS X 6 8B-CPX-016-010 BADGE,AIWA 27.5 a
OTHERS O 7 8C-CP4-001-010 RING,W a
OTHERS O 8 8C-CP4-002-010 RING,TW a
OTHERS O 9 8C-CP4-004-010 GRILLE,FRAME ASSY a
OTHERS X 10 8C-CP4-005-010 NET, a
OTHERS X 11 8C-CP4-006-010 LBL,SPEC YJ a
OTHERS O 12 8C-CP4-602-010 SPKR, W 120 25/2 a
OTHERS O 13 8C-CP4-604-010 SPKR, T 25 25/2 a
OTHERS X 14 8C-CP4-003-010 CABI,M a
PACKING DU X 15 8C-CP4-851-010 CUSHION,ASSY-TTT a
ASSY CODE X 16 PC-CP4-917-070 SX-SLEM60 YJMN a
All components used on this model at the production line are shown in this service manual.
However, please note that not all components will be available as spare parts for after-sales service.
Components marked S and O are designated as spare parts for service and will be stocked at the spare parts centers.
Components marked X and R are not designated as spare parts for after sales service, and will not be stocked at the spare parts centers.
– 62 –
Page 63
9420025 921338
2-11, IKENOHA TA 1-CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111
Loading...