Aiwa XPV-520, XPV-5210, XPV-521, XPV-522, XPV-5260-C Service manual

XP-V520

Y

XP-V521
XP-V522
XP-V523
XP-V5210
XP-V5260C

AEZ

AEZ,AK

ALH

AU

AU

SERVICE MANUAL

COMPACT DISC PLAYER

MODELS CD MECHANISM

V5210<AU>,V5260C<AU> DA23LN

520<Y>,V521<AEZ>,V522<AEZ>,V522<AK>,V523<ALH> DA23LH

• This Service Manual does not include “TEST MODE”. This item will be issued

in the next supplement.

• This Service Manual is the "Revision Publishing" and replaces "Simple Manual"

XP-V520 / V521 / V522 / V5210 / V5260C <Y,AEZ,AU>,
(S/M Code No. 09-011-441-2T1).

BASIC CD MECHANISM: DA23LN,DA23LH

S/M Code No. 09-012-441-2R1

REVISION

DATA

SPECIFICATIONS

Tracking system: 3-beam laser
Laser pickup: Semiconductor laser
D/A conversion: 4-times oversampling digital filter + 1-bit DAC
Frequency response: 20 - 20,000 Hz
Output: PHONES / LINE OUT jack (stereo mini-jack)
Maximum output: 523ALH,5210AU,5260CAU:

Power supply: DC 3 V using two LR6 (size AA) alkaline

Dimensions: 128 (W) x 25.8 (H) x 129.5 (D) mm

Weight: Approx. 206 g (7.2 oz.) excluding batteries
AC adaptor AC-D603: Rated voltage:

12 mW + 12 mW (16 ohms at 1 kHz)
520Y,521AEZ,522AEZ,522AK:
10 mW + 10 mW (16 ohms at 1 kHz)
500 mV (47 k ohms at 1 kHz)

batteries
520Y,521AEZ,523ALH,5210AU,5260CAU:
DC 2.4 V using two commercially available
rechargeable batteries (Ni-Cd 1.2 V 700 mAh)
522AEZ,522AK:
DC 2.4 V using supplied rechargeable batteries
EXCEPT 520Y:
AC house current using the supplied AC adaptor
520Y:
AC house current using an AC adaptor whose
rated output is DC 5-6 V,250 - 300 mA

(5 1/8 x 1 1/
(excluding projecting parts and controls)

5210AU,5260CAU: AC 120 V, 60 Hz
521AEZ,522AEZ,522AK: AC 230 V, 50 Hz
523ALH: AC 115 / 230 V, switchable 50/60 Hz

x 5 1/8 in.)

16

Supplied headphone HP-M062<520Y,521AEZ,522AEZ,522AK>
Type: In-ear type
Impedance: 16 ohms
Sensitivity: 103 dB/mW

Recommended commercially available headphones
<520Y,521AEZ,522AEZ,522AK>
Type: In-ear type / Vertical type / Headband type
Impedance: 16-32 ohms
Sensitivity: 96-105 dB/mW

Car audio cassette adaptor<5260CAU>
Frequency range: 50 - 20,000 Hz(It may differ depending on the

type of your cassette car stereo)

Cord Length: 1.5 m (4 ft 11 in.)
Dimensions: 102.4 (W) X 12.1 (H) X 63.8 (D) mm

(4 1/8 X 1/2 X 2 5/8 in.)

Weight: Approx. 41 g (1.4 oz.)

Car battery adaptor<5260CAU>
Input voltage: DC 12 V / 24 V
Output voltage: DC 6 V 300 mA
Cord length: 1.5 m (4 ft 11 in.)
Weight: Approx. 53 g (1.9 oz.)

• Design and specifications are subject to change without
notice.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully
the instructions below when servicing.

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS
NECESSARY TO CONFIRM LASER BEAM EMISSION.
BE SURE TO OBSERVE FROM A DISTANCE OF MORE
THAN 30cm FROM THE SURFACE OF THE OBJEC­TIVE LENS ON THE OPTICAL PICK-UP BLOCK.

s Caution: Invisible laser radiation when

open and interlocks defeated avoid
exposure to beam.

s Advarsel: Usynlig laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of proce­dures other than those specified herin may result in
hazardous radiation exposure.

ATTENTION

L’utillisation de commandes, réglages ou procédures
autres que ceux spécifiés peut entraîner une dangereuse
exposition aux radiations.

ADVARSEL

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
ude af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1
LASER product.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT

Precaution to replace Optical block
(SF-P200L)

Body or clothes electrostatic potential could

ruin laser diode in the optical block. Be sure

ground body and workbench, and use care the

clothes do not touch the diode.

1) After the connection, remove solder shown in
right figure.

10 9

:SOLDER

PICK UP ASSY

116

– 3 –

ELECTRICAL MAIN PARTS LIST

REF. NO. DESCRIPTIONPART NO.

IC

87-A21-448-040 C-IC,BH6554FV
8B-HC4-610-010 C-IC,MN101C439-AJ
87-A21-874-010 C-IC,MN35530
87-A21-140-010 C-IC,MSM51V17400D
87-A21-873-040 C-IC,AN8399SA

87-A21-449-040 C-IC,AN8746SA
87-A21-085-040 C-IC,TA2120FN

TRANSISTOR

87-A30-429-040 C-TR,DTC123JKA
87-A30-075-080 C-TR,2SA1235F
89-211-323-080 C-TR,2SB1132R
89-416-643-080 C-TR,2SD1664R
87-A30-076-080 C-TR,2SC3052F

89-113-695-680 C-TR,2SA1369G/H
87-A30-278-040 C-FET,2SK2980
87-A30-287-040 C-TR,DTC114TKA
87-A30-282-040 C-TR,DTA114TKA
87-A30-377-040 C-TR,2SB815B7

DIODE

87-A40-270-080 C-DIODE,MC2838
87-017-520-080 C-DIODE,SFPB52
87-A40-570-080 C-ZENER,UDZ10B<*EXP 522AK,523ALH>
87-A40-590-040 C-DIODE,HRW0202A
87-A40-880-040 C-ZENER,UDZS 10B<522AK,523ALH>

MAIN C.B

C101 87-012-286-080 CAP, U 0.01-25
C102 87-A11-031-080 C-CAP,E 100-16 M WX
C103 87-012-286-080 CAP, U 0.01-25
C104 87-016-430-080 C-CAP,E 100-6.3 5.5N
C202 87-016-422-080 C-CAP,E 22-6.3

C203 87-012-286-080 CAP, U 0.01-25
C204 87-016-429-080 C-CAP,E 100-4 5.5N
C205 87-010-805-080 CAP, S 1-16
C206 87-A12-159-080 C-CAP, 10-6.3 K B GRM42-6
C207 87-A10-505-040 CAP,E 220-6.3 105 SF

C208 87-016-426-080 C-CAP,E 47-4 5.5N
C209 87-010-831-080 C-CAP,U,0.1-16F
C210 87-A10-047-080 C-CAP,U 1-10 Z F
C211 87-010-787-080 CAP, U 0.022-25
C212 87-012-266-080 C-CAP,U 220P-50 B

C213 87-010-805-080 CAP, S 1-16
C303 87-010-831-080 C-CAP,U,0.1-16F
C304 87-010-831-080 C-CAP,U,0.1-16F
C305 87-012-286-080 CAP, U 0.01-25
C306 87-012-286-080 CAP, U 0.01-25

C307 87-012-286-080 CAP, U 0.01-25
C309 87-016-429-080 C-CAP,E 100-4 5.5N
C310 87-010-831-080 C-CAP,U,0.1-16F
C401 87-016-429-080 C-CAP,E 100-4 5.5N
C402 87-010-831-080 C-CAP,U,0.1-16F

C403 87-016-431-080 C-CAP,E 220-4 5.5N
C405 87-A10-260-080 C-CAP,U 0.1-16 K B
C406 87-012-271-080 CAP, U 560P-50
C407 87-010-787-080 CAP, U 0.022-25
C408 87-A10-260-080 C-CAP,U 0.1-16 K B

C409 87-A10-827-080 C-CAP,U 0.47-6.3 K B
C410 87-012-286-080 CAP, U 0.01-25
C411 87-010-831-080 C-CAP,U,0.1-16F
C412 87-016-429-080 C-CAP,E 100-4 5.5N
C413 87-010-831-080 C-CAP,U,0.1-16F

C415 87-010-831-080 C-CAP,U,0.1-16F
C417 87-012-188-080 C-CAP,U 47P-50 CH
C418 87-012-184-080 C-CAP,U 33P-50 CH

NO.

C419 87-012-184-080 C-CAP,U 33P-50 CH
C421 87-010-831-080 C-CAP,U,0.1-16F
C422 87-010-831-080 C-CAP,U,0.1-16F
C423 87-010-831-080 C-CAP,U,0.1-16F
C451 87-010-831-080 C-CAP,U,0.1-16F

C501 87-016-429-080 C-CAP,E 100-4 5.5N
C502 87-010-831-080 C-CAP,U,0.1-16F
C503 87-010-787-080 CAP, U 0.022-25
C504 87-010-787-080 CAP, U 0.022-25
C505 87-012-273-080 C-CAP,U 820P-50 B<*EXP 523ALH>

C505 87-012-276-080 C-CAP,U 1500P-50 B<523ALH>
C506 87-012-198-080 CAP 180P
C507 87-012-273-080 C-CAP,U 820P-50 B
C508 87-016-426-080 C-CAP,E 47-4 5.5N
C509 87-012-281-080 C-CAP,U 3900P-50 B

C510 87-012-283-080 C-CAP,U 5600P-50 B
C511 87-A11-228-080 C-CAP,U 0.027-25 K B
C512 87-016-429-080 C-CAP,E 100-4 5.5N
C513 87-A11-228-080 C-CAP,U 0.027-25 K B
C514 87-A10-828-080 C-CAP,U 0.33-6.3 K B

C515 87-A10-260-080 C-CAP,U 0.1-16 K B
C516 87-012-180-080 C-CAP,U 22P-50 CH
C517 87-012-180-080 C-CAP,U 22P-50 CH
C520 87-016-426-080 C-CAP,E 47-4 5.5N
C521 87-012-274-080 CHIP CAP,U 1000P-50B

C522 87-A10-047-080 C-CAP,U 1-10 Z F
C523 87-A10-047-080 C-CAP,U 1-10 Z F
C601 87-016-430-080 C-CAP,E 100-6.3 5.5N
C602 87-012-286-080 CAP, U 0.01-25
C603 87-012-286-080 CAP, U 0.01-25

C701 87-016-429-080 C-CAP,E 100-4 5.5N
C702 87-012-335-080 C-CAP,U 270P-50 SL
C703 87-012-335-080 C-CAP,U 270P-50 SL
C706 87-010-831-080 C-CAP,U,0.1-16F
C707 87-A10-047-080 C-CAP,U 1-10 Z F

C708 87-A10-047-080 C-CAP,U 1-10 Z F
C709 87-A10-047-080 C-CAP,U 1-10 Z F
C710 87-016-421-080 C-CAP,E 10-16 5.5N
C711 87-016-422-080 C-CAP,E 22-6.3
C715 87-016-421-080 C-CAP,E 10-16 5.5N

C716 87-010-831-080 C-CAP,U,0.1-16F
C717 87-010-831-080 C-CAP,U,0.1-16F
C718 87-016-431-080 C-CAP,E 220-4 5.5N
C719 87-016-431-080 C-CAP,E 220-4 5.5N
C720 87-012-274-080 CHIP CAP,U 1000P-50B

C721 87-012-274-080 CHIP CAP,U 1000P-50B
CN301 87-A60-792-080 C-CONN,30P V 30FLT-SM1TB
CN501 87-009-214-080 CONN,16P 52207-1690
CN601 87-099-522-080 CONN,6P ZH-SM3 V W
FB702 83-XM1-617-080 C-COIL,BK2125HM601

FB703 83-XM1-617-080 C-COIL,BK2125HM601
FB705 83-XM1-617-080 C-COIL,BK2125HM601
FFC301 8B-HC4-605-010 FF-CABLE,30P 0.5 45MM
J101 87-A61-447-010 JACK,DC DJ26B BLK 6
J701 87-A61-446-010 JACK,3.5 GRN ST W/REM

L201 87-A50-355-080 C-COIL,330UH LQH3C
L202 87-A50-330-080 C-COIL,100UH-D75C
L203 87-A50-355-080 C-COIL,330UH LQH3C
L302 87-A50-367-080 C-COIL, 10UH LQG21F
L401 87-A50-367-080 C-COIL, 10UH LQG21F

L402 87-A50-012-080 C-COIL,100UH LQH3C
L501 87-A50-367-080 C-COIL, 10UH LQG21F
L502 87-A50-367-080 C-COIL, 10UH LQG21F
S101 87-A92-085-010 SW,MICRO ESE11SV1
S302 87-A90-494-080 C-SW,SL 1-1-3 SSSS81

S303 87-A90-494-080 C-SW,SL 1-1-3 SSSS81
VR701 87-A92-142-010 C-VR,RTRY 30KCX2 H K142R0Z0J
X401 87-A70-202-080 C-VIB,CER 16.93MHZ CSACV-MXJ04

REF. NO. DESCRIPTIONPART NO.KANRI

KANRI
NO.

– 4 –

REF. NO. DESCRIPTIONPART NO.

NO.

FRONT C.B

C802 87-012-274-080 CHIP CAP,U 1000P-50B
C803 87-010-831-080 C-CAP,U,0.1-16F
CN801 87-A60-791-080 C-CONN,30P H FLZ-RSM1TB
LCD801 8A-HC5-621-010 LCD,AHC-5 REFLEX
S801 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

S802 87-A91-668-080 C-SW,TACT EVQ-PQH-B55
S803 87-A91-668-080 C-SW,TACT EVQ-PQH-B55
S804 87-A91-668-080 C-SW,TACT EVQ-PQH-B55
S805 87-A91-668-080 C-SW,TACT EVQ-PQH-B55
S806 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

S807 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

*NOTE: EXP= EXCEPT

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

88

REF. NO. DESCRIPTIONPART NO.KANRI

KANRI
NO.

A

Resistor Code

Chip resistor

Wattage Type Tolerance

1/16W 1005 5% CJ

1/16W

1/10W

1/8W

1608

2125

3216

5%

5%

5%

TRANSISTOR ILLUSTRATION

C

Symbol

CJ

CJ

CJ

Figure

Value of resistor

Form

L

Dimensions (mm)

t

W

D

0.55

Resistor Code

108

118

128

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45

2 1.25 0.45

3.2

1.6

: A
: A

B

E

2SA1235F
2SB815B7
2SC3052F
DTA114TKA
DTC114TKA
DTC123JKA

CBE

2SA1369G/H
2SB1132R
2SD1664R

G

S

2SK2980

– 5 –

WIRING  1 (MAIN) <1 / 2>

1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

 6 

WIRING  1 (MAIN) <2 / 2>

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

 7 

R

S

T

U

SCHEMATIC DIAGRAM  1 (MAIN)

 8 

WIRING – 2 (FRONT)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

– 9 –

R

S

T

U

SCHEMATIC DIAGRAM  2 (FRONT)

 10 

IC B L O C K DIAGRAM

 11 

LCD DISPLAY

– 12 –

IC DESCRIPTION

IC, MN101C439-AJ

Pin No. Pin Name I/O Description

1 COM03 O LCD common output.

2 COM02 O LCD common output.

3 COM01 O LCD common output.

4 COM00 O LCD common output.

5 VLC3 - LCD drive voltage setting terminal.

6 VLC2 - LCD drive voltage setting terminal.

7 VLC1 - LCD drive voltage setting terminal.

8 VDD - LCD power.

9

10 OSC1 O Micon main clock oscillator output.

11 VSS - GND.
12 XI I Sub clock oscillator.(Connected to GND)

13 XO O Sub clock oscillator. (Not used)

14 MMOD I Processor mode unused.(Connected to GND)

15 VREF- - Connected to GND.

OSC2 O

Micon main clock oscillator output. (Not used)

16 K-FUNC I "FUNCTION" key input.

17 K-P/S I "PLAY" and "STOP" key inputs.

18 ACIN I AC adaptor detection.

19 VDIN I Main clock (8 MHz).

20 K-RMC I Wired remote control input.

21 SWDO I Digital out "ON/OFF" input. ON at "L".(Not used)

22 SWEASS I EASS mode selection input. Refer to A/D table.

23 SWR/H I Resume/Hold switch input.

24 VREF+ - Connected to VDD.

25 MDATA O DSP MDATA output.

26 STAT I DSP STAT input.

27 MCLK O DSP MCLK output.

28 MLD O DSP MLD output.

29 SUBQ O Power down output for H/A.

30 SQCK O Selection output for EASS gain control. EASS at "L".

31 BEEP O Buzzer output for headphone.

32 RST I Micro computer reset input.

33 NRST O DSP reset output.

34 SWIL I Limited switch input.

35 PC O Power off output for CD server driver. Power off at "L".
36 CDRW O CD RW play gain level selection output. Gain set at "H".
37 CDRW O CD RW play gain level selection output. Gain set at "L". (Not used)

38 BLKCK I DSP BLKCK input.

39 RSENSOR I Wireless remote control sensor signal input. (Not used)

40 4/5 I Not used.

41 EASS 2/3 - Connected to ground.

– 13 –

Pin No. Pin Name I/O Description

42 PU-ON O H/A power down output.

43 EASSON O EASS gain up selection output. EASS ON at = "L".

44 DSL2 O Headphone DSL2 control output. DSL2 at "H". DSL1/OFF at "L".

45 DSL1 O Headphone DSL ON control output. DSL ON at "H".

46 MUTE O Audio mute output.

47 STANDBY O Headphone standby output. Standby at "L". Power ON at "H".

48 LCDRDO O Wired LCD remote control output. (Not used)

49 P-OFF O Power IC power off output. Power OFF at "L".

50 DSCHRG O Discharge output.

51 CHRG O Charge output.

52 BAT-F O Battery balance full indication LED output. (Not used)

53 BAT-M O Battery balance medium indication LED output. (Not used)

54 BAT-E O Battery balance empty indication LED output. (Not used)

55 TX-ON - Not used.

56 SWCL I Cover open/close detection switch input.

57 EL-ON O EL back light control output.

58 SPCON O Spindle PWM control output. (Not used)

59 CAR-LED O CAR-KIT model button LED light output. (Not used)

60 E-MODE I Shaft damage mode (No shaft damage mode found at "H"). (Not used)

61 TEST I Enter test mode at "L". (Not used)

62 M1/NM2 I 10 or 10/40 sec selection input. 10 sec at "H", 10/40 sec at "L". (Not used)

63 NC - Not connected.

64 SEG15 O LCD segment output.

65 SEG14 O LCD segment output.

66 SEG13 O LCD segment output.

67 SEG12 O LCD segment output.

68 SEG11 O LCD segment output.

69 SEG10 O LCD segment output.

70 SEG09 O LCD segment output.

71 SEG08 O LCD segment output.

72 SEG07 O LCD segment output.

73 SEG06 O LCD segment output.

74 SEG05 O LCD segment output.

75 SEG04 O LCD segment output.

76 SEG03 O LCD segment output.

77 SEG02 O LCD segment output.

78 SEG01 O LCD segment output.

79 SEG00 O LCD segment output.

80 NC - Not connected.

– 14 –

A/D TABLE

HEX K-FUNC (PIN 16) SWEASS (PIN 22) SWR/H (PIN 23) K-P/S (PIN 17)

E8 ~ FF OFF EASS ON RESUME OFF

CB ~ E8 NOT USED OFF OFF PLAY

AD ~ CA DSL OFF OFF PLAY

90 ~ AC MODE OFF OFF PLAY

71 ~ 8F ENTER 0FF HOLD/RESUME PLAY

53 ~ 70 B.S OFF HOLD/RESUME STOP

35 ~ 52 F.S OFF HOLD/RESUME STOP

17 ~ 34 NOT USED OFF OFF STOP

1 ~ 16 OFF OFF OFF OFF

A/D TABLE

HEX K-RMC (PIN 20)

E8 ~ FF OFF

BB ~ E8 NOT USED

89 ~ BA DSL

5F ~ 88 PLAY

42 ~ 5E MODE

2E ~ 41 STOP

1F ~ 2D B.S

OB ~ 1E F.S

00 ~ 0A OFF

– 15 –

IC, MN35530

Pin No. Pin Name

1 DVDD3 - Power supply for DRAM interface.

2 D0 I/O Input/Output data 0 for DRAM.

3 D1 I/O Input/Output data 1 for DRAM.

4 NWE O Output write enable signal for DRAM.

5 NRAS O Output RAS control signal for DRAM.

6 D2 I/O Input/Output data 2 for DRAM.

7 D3 I/O Input/Output data 3 for DRAM.

8 NCAS0 O Output CAS control signal 0 for DRAM.

9 A10 O Output address signal 10.

10 ~ 14 A8 ~ A4 O Output address signal 8 ~ 4.

15 A9 O Output address signal 9.

16 ~ 19 A0 ~ A3 O Output address signal 0 ~ 3.

20 DVSS2 - Ground for digital circuit.

21 DVDD2 - Power supply for digital circuit.

22 SPOUT O PWM output of spindle.

23 TRVP O PWM output of positive traverse signal.

24 TRVM O PWM output of negative traverse signal.

25 TRP O PWM output of positive tracking signal.

I/O

Description

26 TRM O PWM output of negative tracking signal.

27 FOP O PWM output of positive focus signal.

28 FOM O PWM output of negative focus signal.

29 FBAL O Output for focus balance adjustment.

30 TBAL O Output for tracking balance adjustment.

31 CSEL - Reference voltage for DA output (TRVP, TRP, FOM, FOP, FBAL, TBAL, DSLF2).

32 FE I Focus error signal input (analog input).

33 TE I Tracking error signal input ( analog input).

34 RFENV I RF envelope signal input (analog input).

35 OFT I Off track signal input. "H" : Off track.

36 NRFDET I RF detection signal input. "L" : Detect.

37 BDO I Drop out signal input. "H" : Drop out.

38 LDON O Laser ON signal output. "H" : ON.

39 ARF I RF signal input.

40 IREF I Reference current input terminal.

41 ADPVCC - Reference voltage level for PWM output drive.

42 DSLF O Loop filter terminal for DSL.

43 DRF I DSL input.

44 PLLF O Loop filter terminal for PLL.

45 VCOF O Loop filter terminal for pitch controller and jitter free VCO.

46 AVDD2 - Power supply for analog circuit (DSL, PLL, VCOF, AD, DA).

47 AVSS2 - Ground for analog circuit (DSL, PLL, VCOF, AD, DA).

48 OUTL O Output Lch audio.

– 16 –

Pin No. Pin Name

49 AVSS1 - Ground for analog circuit. (For audio output)

50 OUTR O Output Rch audio.

51 AVDD1 - Power supply for analog circuit. (For audio output)

52 FSEL I Input noise filter ON / OFF switching. "L" : ON. "H" : OFF.

53 TMOD1 I Terminal mode switching input 1. (Connected to GND)

54 TMOD2 I Terminal mode switching input 2. (Connected to GND)

55 FLAG O Flag signal output. (Not used)

56 CLVS/IPFLAG - Not used.

57 ~ 59 EXT 0 ~ 2 I/O Expansion input / output port 0 ~ 2. (Not used)

60 TX O Digital audio interface output signal. (Not used)

61 MCLK I Microcomputer command clock signal input (latch data at rising edge).

62 MDATA I Microcomputer command data signal input.

63 MLD I Microcomputer command load signal input. "L" : Load.

I/O

Description

64 BLKCK I

65 SQCK/BCLK I Input clock for sub code Q register.

66 SUBQ/LRCK O Output sub code Q data.
67 DMUTE/SRDATA I Input mute. "H" : Mute. (Connected to GND)

68 STAT O

69 NRST I Input reset. "L" : Reset.

70 SPPOL O PWM output of spindle signal drive.

71 PMCK O 88.2kHz clock signal output.(Not used)

72 SMCK O 4.2336MHz clock signal output.

73 SUBC/SSYNC O Output sub code serial. (Not used)

74 SBCK/64FS I Input clock for subcode serial. (Not used)

75 NCLDCK O Sub code frame clock signal output ( fCLDCK = 7.35kHz). (Not used)
76 NTEST - Test terminal.(connected to power supply)

77 X1 I Crystal oscillator circuit input terminal (f = 16.93MHz).

78 X2 O Crystal oscillator circuit output terminal (f = 16.93MHz).

79 DVDD1 - Power supply for digital circuit.

80 DVSS1 - Ground for digital circuit.

Input sub code block clock signal (fBLKCK = 75kHz) / Input SYNC signal for

CDTEXT (fDQSY = 300kHz).

Output status signal (CRC,RESY,CLVS,NTTSTOP,SQOK,FLAG6,SENSE,NFLOCK,

NTLOCK,BSSEL,SUBQDATA,CDTEXT DATA,ANT-SHOCK READ OUT DATA.)

– 17 –

WAVEFORM

1

IC501 PIN 4 (RFN)

IC501 PIN 21 (TEOUT)

2

0.5 V/div

0.5 µs/div

3

IC501 PIN 23 (FEOUT)

IC301 PIN 10 (OSC1)

4

10 mV/div

0.1 ms/div

0.1 V/div
1 ms/div

0.5 V/div

0.1 µs/div

– 18 –

MECHANICAL EXPLODED VIEW 1 / 1

1

2

3

4

7

PLATE,LCD

LCD

5

23

PWB

8

9

A

11

10

12 13

PWB

18

6

B

14

15

DA23LH
DA23LN

16

C

(EXCEPT 5210,5260)
( 5210,5260 only)

17

22

19

20

21

D

D

– 19 –

MECHANICAL PARTS LIST 1 / 1

PART NO.

NO.

1 8B-HC5-007-010 PANEL,DISPLAY
2 8B-HC5-006-010 WINDOW,DISPLAY<520Y1SF>
2 8B-HC5-016-010 WINDOW,DISPLAY 521<521AEZ1SF>
2 8B-HC5-031-010 WINDOW,DISPLAY 5210<5210AUBSF>
2 8B-HC5-017-010 WINDOW,DISPLAY 522<522AK1SF,522AEZ1SF>

2 8B-HC5-018-010 WINDOW,DISPLAY 523<523ALH1SF,523ALH1BSF>
2 8B-HC5-032-010 WINDOW,DISPLAY 5260C<5260CAUBSF,5260CAUB4SF>
3 8B-HC5-010-010 KEY,SKIP
4 8B-HC5-001-010 LID,CD<EXCEPT 5210AUBSF,5260CAUBSF,5260CAUB4SF>
4 8B-HC5-014-010 LID,CD U<5210AUBSF,5260CAUBSF,5260CAUB4SF>

5 8A-HC5-202-010 JOINT,LCD AHC5
6 8B-HC5-008-010 HLDR,LID CD
7 8B-HC5-011-010 KEY,MODE
8 8B-HC5-009-010 KEY,PLAY
9 8B-HC4-203-010 SPR-T,OPEN

10 8B-HC4-002-010 CABI,CENTER
11 8B-HC4-204-010 SPR-T,KNOB
12 8B-HC4-011-010 KNOB,SL OPEN
13 8B-HC4-205-010 LEVER,OPEN
14 8B-HC4-016-010 HLDR,OPEN

15 8Z-HC1-225-010 DMPR,MECHA(SP)
16 8B-HC4-202-010 BAT-CONTACT,(-)
17 8B-HC4-201-010 BAT-CONTACT,(+)
18 8B-HC4-013-010 KNOB,SL EASS
19 8B-HC4-012-010 KNOB,SL HOLD

20 8B-HC4-005-010 CABI ASSY,BOTTOM
21 8Z-HC4-027-010 FOOT,DIA10
22 8Z-HC7-216-010 BAT-CONTACT,(+)(-) (SP)
23 8B-HC4-208-010 SHAFT,LID (15.8)
A 87-067-736-010 SCREW,1.4-2 BLK NLOCK

B 87-067-732-010 TAPPING SCREW, VT1.4-3
C 87-067-868-010 V+1.7-4 HL BLK
D 87-067-869-010 V+1.7-8 HL BLK

DESCRIPTIONREF. NO. KANRI

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange
G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver

T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green

LD Dark Blue DT Transparent Orange GM Metallic Green

YM Metallic Yellow DM Metallic Orange PT Transparent Pink

LA Aqua Blue GL Light Green

– 20 –

CD MECHANISM EXPLODED VIEW 1 / 1 (DA23LN)

D

D

2

4

9

A

3

5

1

7

8

C

6

B

– 21 –

10

CD MECHANISM PARTS LIST 1 / 1 (DA23LN)

PART NO.

NO.

1 S0-A41-A20-604 PICKUP ASSY LASER P200L
2 S0-M10-A10-800 MOTOR SPINDLE ASSY
3 S0-M10-A10-900 MOTOR SLED ASSY
4 S2-311-A12-200 CHASSIS
5 S2-511-A23-200 GEAR MIDDLE

6 S2-511-A23-100 GEAR,SCREW
7 S2-511-A23-400 GEAR,RACK
8 S2-511-A07-901 SPINDLE SCREW
9 S4-S13-A00-200 SW,LEAF
10 S2-451-A18-100 HOLDER GEAR

A SS-EXE-A04-000 SCR PAN PCS 1.4-2.2
B SS-GXE-A00-301 SPECIAL SCREW M1.7-6.0
C SS-EXE-A14-100 SPECIAL SCREW
D SS-GXE-A00-202 SPECIAL SCREW M1.7-4.0

DESCRIPTIONREF. NO. KANRI

– 22 –

CD MECHANISM EXPLODED VIEW 1 / 1 (DA23LH)

2

8

A

3

6

1

7

4

C

5

B

– 23 –

CD MECHANISM PARTS LIST 1 / 1 (DA23LH)

PART NO.

NO.

1 S0-A41-A20-600 PICKUP LASER ASSY
2 S0-M10-A13-500 MOTOR ASSY SPDL LH
3 S0-M10-A10-900 MOTOR SLED ASSY
4 S0-551-A00-900 SPINDLE ASSY SCREW
5 S2-451-A18-100 HOLDER GEAR

6 S2-511-A23-200 GEAR MIDDLE
7 S2-511-A23-400 GEAR,RACK
8 S4-S13-A00-200 SW,LEAF
A SS-EXE-A04-000 SCR PAN PCS 1.4-2.2
B SS-GXE-A00-300 SPECIAL SCREW

C SS-GXE-A14-100 SPECIAL SCREW

DESCRIPTIONREF. NO. KANRI

– 24 –

ACCESSORIES / PACKAGE LIST

PART NO.

DESCRIPTIONREF. NO. KANRI

NO.

1 86-YK1-001-410 ADAPTOR,CAP-6<5260CAU>
1 86-YK1-002-210 ADAPTOR,DC-602<5260CAU>
2 87-B30-422-010 HEADPHONE,HP-M061<5210AU,5260CAU>
2 87-B30-423-010 HEADPHONE,HP-M062<520Y,522AK,522AEZ,521AEZ>
2 87-B30-420-010 HEADPHONE,HP-MR059<523ALH>

3 8B-HC5-915-010 IB,EZ(EGF)S V521<521AEZ>
3 8B-HC5-905-010 IB,EZ(EGF)S V522/523<522AK,522AEZ>
3 8B-HC5-917-010 IB,EZ(PHNCZ)S V521<521AEZ>
3 8B-HC5-907-010 IB,EZ(PHNCZ)S V522/523<522AEZ>
3 8B-HC5-916-010 IB,EZ(SID)S V521<521AEZ>

3 8B-HC5-906-010 IB,EZ(SID)S V522/523<522AEZ>
3 8B-HC5-904-010 IB,LH(3L)S<523ALH>
3 8B-HC5-901-010 IB,U(3L)S<5210AU,5260CAU>
3 8B-HC5-925-010 IB,Y(EGF)S V520<520Y>
3 8B-HC5-927-010 IB,Y(PHNCZ)S V520<520Y>

3 8B-HC5-926-010 IB,Y(SID)S V520<520Y>

!

4 87-A91-017-010 PLUG,CONVERSION JT-0476<523ALH>

!

5 87-B30-283-110 AC ADAPTOR,AC-D603ENC<522AK,522AEZ,521AEZ>

!

5 87-B30-285-110 AC ADAPTOR,AC-D603HRNC<523ALH>

!

5 87-B30-282-010 AC ADAPTOR,AC-D603UNC<5210AU,5260CAU>

6 87-B30-362-010 BAT,NB-305 NC(2PSC)<522AK,522AEZ>

– 25 –

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:[phone]

Printed in Singapore9620450,0251431