HS-AP1MK7
S
UPPLEME
N
T
Y1
SERVICE MANUAL
STEREO
CASSETTE PLAYER
This Service Manual contains information about the difference between HS-AP1MK7
<Y1> and HS-AP1MK3<YZ1>. If requiring other information, see Service Manual
HS-GS174/AP1MK3<YZ1,Y>. (S/M Code No. 09-978-215-40I)
BASIC TAPE MECHANISM : TN-8SA-128
S/M Code No. 09-993-410-2S2
SPECIFICATIONS
Maximum output 8 mW + 8 mW (EIAJ 16 ohms)
Power sources DC 3V, using two R6 (size AA) batteries
Maximum Dimensions 114 (W) x 92 (H) x 36.8 (D) mm
Weight Approx.155 g, 5.4 oz (excluding batteries)
• Design and specifications are subject to change without notice.
• Dolby noise reduction manufactured under license from Dolby
Laboratories Licensing Corporation.
"DOLBY" and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
9 mW + 9 mW (EIAJ 32 ohms)
AC house current using an optional AC
adaptor aiwa AC-300/AC-302
1
/2 x 35/8 x 11/2 in.)
(4
ELECTRICAL MAIN PARTS LIST
PART NO. KANRI
NO.
IC
87-A20-460-040 IC,MM1336CF
87-001-875-080 IC,BA1106FS
DIODE
87-020-339-080 CHIP DIODE,1SS226
MAIN C.B
C105 87-015-676-010 CAP,E 47-6.3 7L
C106 87-015-676-040 E/CAP 47/6.3
C116 87-015-691-040 CAP,E0.1-50 SRA
C119 84-439-620-010 CAP, ELECT 470-4
C120 84-439-620-010 CAP, ELECT 470-4
C121 87-015-695-010 CAP,E 1-50 7L
C123 87-015-674-040 CAP E 22-6.3M SRA
C125 87-015-674-080 CAP 22U-6.3V
C126 87-015-674-010 CAP 22U-6.3V
C127 87-018-134-010 CERA-SOL SS0.01
C230 87-018-134-010 CERA-SOL SS0.01
C701 87-010-303-080 C-CAP,S 330P-50CH
C702 87-010-303-080 C-CAP,S 330P-50CH
C703 87-018-131-010 CAP,1000P
J101 87-A60-122-010 JACK,DC 3.8
J102 83-HRL-602-010 JACK,3.5ST
R115 87-022-657-010 RES,K43G 0.68
SFR101 87-024-197-010 SEMI-FIXED RESISTOR, 1K
SFR102 87-024-197-010 SEMI-FIXED RESISTOR, 1K
SFR103 87-024-197-010 SEMI-FIXED RESISTOR, 1K
DESCRIPTIONREF. NO. KANRI
REF. NO. DESCRIPTIONPART NO.
NO.
SW101 87-A90-050-010 SW, SL 2-2-2 NS (BLK)
TH101 87-026-256-090 THERMISTOR,HT-100
VR101 87-024-326-010 VOLUME 20KA
DOLBY C.B
C301 87-016-462-080 C-CAP,S 1-16 F
C302 87-016-462-080 C-CAP,S 1-16 F
C303 87-010-193-080 CHIP CAPACITOR,0.033
C304 87-010-193-080 CHIP CAPACITOR,0.033
C305 87-010-186-080 CAP,CHIP 4700P
C306 87-010-186-080 CAP,CHIP 4700P
C307 87-010-197-080 CAP, CHIP 0.01 DM
C308 87-010-197-080 CAP, CHIP 0.01 DM
C309 87-010-193-080 CHIP CAPACITOR,0.033
C310 87-010-193-080 CHIP CAPACITOR,0.033
C311 87-010-196-080 CHIP CAPACITOR,0.1-25
C312 87-010-196-080 CHIP CAPACITOR,0.1-25
C313 87-016-436-080 C-CAP,TN 47-4(B2)
C315 87-010-196-080 CHIP CAPACITOR,0.1-25
C316 87-016-462-080 C-CAP,S 1-16 F
C317 87-016-462-080 C-CAP,S 1-16 F
C320 87-016-462-080 C-CAP,S 1-16 F
C321 87-016-462-080 C-CAP,S 1-16 F
S303 87-036-123-080 CHIP SLIDE SWITCH,1-1-2
GEQ C.B
83-HRG-605-110 G-EQ ASSY(SB)
ADJUSTMENT
<TAPE PLAYER SECTION>
1. Motor load adjustment.
Perform the STOP−>PLAY and REVERSE operations ( or
PAUSE ON−>OFF ) after the motor is replaced. When the
tape starts running smooth, this adjustment is not necessary.
If wow is conspicuous at the begining of the tape-run, perform
this adjustment following the procedure below.
1) Solder both resistor pattern (B) and (C) of the MOTOR
AND GOVERNOR MATCHING ADJ. resistor group.
2) Set the tape speed (using speed adjustment SFR101).
3) Restrict the motor rotation by hand (or turn PAUSE ON).
4) Remove your hand and listen to the begining of the tape-run.
5) When the rise of tape is running is smooth, no more
adjustment is necessary.
If wow continues for 1 to 2 seconds at the rise time, reduce
the combined resistance according to procedure 6 and check
that the tape starts running smooth.
6) Solder the resistor pattern according to the table below.
Pattern
High
resistance (C)
Medium
resistance (B)
Low
resistance (A)
(Procedure
1 above)
Solder
Solder
Open
Step (1)
Open
Solder
Open
7) Finally re-check the tape speed.
Caution : Cool the pattern down to normal temperature
after soldering. If the pattern remains heated,
the governor circuit does not operate normally.
MECHANICAL PARTS LIST 1 / 1
PART NO.
NO.
1 87-HGA-016-010 KNOB,SL DOL AP1MK7
2 87-HGA-017-010 KNOB,SL TRE AP1MK7
3 87-HGA-018-010 KNOB,SL BAS AP1MK7
4 87-HGA-019-010 KNOB,SL S-B AP1MK7
5 87-HGA-015-010 PANEL,CASS AP1MK7
6 87-HGA-008-010 PLATE,INDI G-EQ
7 87-HGA-009-010 PLATE,INDI DOLBY
8 87-HGA-014-010 LID,CASS AP1MK7
9 87-HG8-208-010 SPR-T,CASS
10 87-HG8-215-010 SPR-P,CASS A
11 87-HGA-067-010 FRAME,CENTRE DOLBY
12 87-HGA-058-010 BTN,PLAY
13 87-HGA-059-010 BTN,REW
14 87-HGA-060-010 BTN,FF
15 87-HGA-061-010 BTN,STOP
16 87-HG8-015-010 KNOB,RTRY VOLUME
17 87-HGA-063-010 LID,BAT
18 87-HGA-068-010 CABI,REAR
A 87-067-732-010 TAPPING SCREW,VT1.4-3
B 87-262-505-310 V+1.4-2.5 BLK
C 87-262-533-310 V+1.7-6
DESCRIPTIONREF. NO. KANRI
Step (2)
Solder
Open
Solder
ACCESSORIES / PACKAGE LIST
PART NO.
NO.
1 87-HGA-907-010 IB,YZ(6L)C
2 87-B30-168-010 HEADPHONE,HP-MOO6(K)
3 84-447-019-110 CLIP,BELT
DESCRIPTIONREF. NO. KANRI
A4
L
9630466
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore
Loading...