AIWA HMC 586 LC 4 B Service Manual

www.DataSheet4U.com
v00.0206
HMC586LC4B
AMPLIFIER, 4.0 - 8.0 GHz
9
Typical Appli cations
Low Noise wideband MMIC VCO is ideal for:
• Industrial/Medical Equipment
• Test & Measurement Equipment
• Military Radar, EW & ECM
Functional Diagram
Features
Wide Tuning Bandwidth
Pout: +5 dBm
Low SSB Phase Noise: -100 dBc/Hz @100 kHz
No External Resonator Needed
Single Positive Supply: +5V @ 55 mA
RoHS Compliant 4 x 4 mm SMT Package
General Description
The HMC586LC4B is a wideband GaAs InGaP Voltage Controlled Oscillator which incorporates the resonator, negative resistance device, and varactor diode. Output power and phase noise performance are excellent over temperature due to the oscillator’s monolithic construction. The Vtune port accepts an analog tuning voltage from 0 to +18V. The HMC586LC4B VCO operates from a single +5V sup­ply, consumes only 55 mA of current, and is housed in a RoHS compliant SMT package. This wideband VCO uniquely combines the attributes of ultra small size, low phase noise, low power consumption, and wide tuning range.
VCOs & PLOs - SMT
9 - 166
Electrical Specifications, T
Parameter Min. Typ. Max. Units
Frequency Range 4.0 - 8.0 GHz
Power Output 25 dBm
SSB Phase Noise @ 100 kHz Offset -100 dBc/Hz
SSB Phase Noise @ 10 kHz Offset -75 dBc/Hz
Tune Voltage (Vtune) 0 18 V
Supply Current (Icc) (Vcc = +5.0V) 40 75 mA
Tune Port Leakage Current (Vtune = +15V) 10 μA
Output Return Loss 7dB
2nd Harmonic -14 dB c
Pulling (into a 2.0:1 VSWR) 4MHz pp
Pushing @ Vtune= +5V 40 MHz/V
Frequency Dri ft Rate 0.8 MHz/°C
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
= +25° C, Vcc = +5V
A
Order On-line at www.hittite.com
v00.0206
HMC586LC4B
AMPLIFIER, 4.0 - 8.0 GHz
Frequency vs. Tuning Voltage, Vcc = +5V
9
8
7
6
5
OUTPUT FREQUENCY (GHz)
4
3
0 2 4 6 8 10 12 14 16 18 20
TUNING VOLTAGE (VOLTS)
4.75 V
5.0 V
5.25 V
Sensitivity vs. Tuning Voltage, Vcc= +5V
600
500
400
300
200
SENSITIVITY (MHz/VOLT)
100
0
0 2 4 6 8 10 12 14 16 18 20
TUNING VOLTAGE (VOLTS)
+25 C +85 C
-40 C
Frequency vs. Tuning Voltage, T = +25 C
9
8
7
6
5
OUTPUT FREQUENCY (GHz)
4
3
0 2 4 6 8 10 12 14 16 18 20
TUNING VOLTAGE (VOLTS)
+25 C +85 C
-40 C
Output Power vs. Tuning Voltage, Vcc= +5V
10
8
6
4
2
0
OUTPUT POWER (dBm)
-2
-4 0 2 4 6 8 10 12 14 16 18 20
TUNING VOLTAGE (VOLTS)
+25 C +85 C
-40 C
9
VCOs & PLOs - SMT
SSB Phase Noise vs. Tuning Voltage
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
SSB PHASE NOISE (dBc/Hz)
-100
-110
-120 0 2 4 6 8 10 12 14 16 18 20
TUNING VOLTAGE (VOLTS)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
10 kHz 100 kHz
Order On-line at www.hittite.com
Typical SSB Phase Noise @ Vtune= +5V
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
SSB PHASE NOISE (dBc/Hz)
-110
-120
2
10
3
10
OFFSET FREQUENCY (Hz)
4
10
5
10
6
10
9 - 167
9
v00.0206
Absolute Maximum Ratings
Vcc +5.5 Vdc
Vtune 0 to +22V
Junction Temperature 135 °C
Continuous Pdiss (T = 85°C) (derate 12.5 mW/°C above 85°C)
Thermal Resistance (junction to ground paddle)
Storage Temperature -65 to +150 °C
Operating Temperature -40 to +85 °C
625 mW
80 °C/W
Outline Drawing
HMC586LC4B
AMPLIFIER, 4.0 - 8.0 GHz
VCOs & PLOs - SMT
9 - 168
NOTES:
1. PACKAGE BODY MATERIAL: ALUMINA
2. LEAD AN D GROUND PADD LE PLATING: GOLD FLASH OVER N i.
3. DIMENSIONS ARE IN INCHES [MILLIMETERS].
4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
5. PACKAGE WARP SH ALL NOT EXCEED 0.05mm DATUM -C-
6. ALL GROUND LEADS AND GROUND PADDLE MUST B E SOLDERED
TO PCB RF GROUND.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
Order On-line at www.hittite.com
HMC586LC4B
v00.0206
AMPLIFIER, 4.0 - 8.0 GHz
Pin Descriptions
Pin Number Function Description Interface Schematic
1 - 3, 5 - 11,
13, 17 - 24
4Vtune
12 Vcc Supply Voltage Vcc= +5V
14, 16 GND
15 RFOUT RF output (AC coupled)
N/C
No Connection. These pins may be connected to RF/DC
ground. Performance will not be affected.
Control Voltage and Modulation Input. Modulation
bandwidth dependent on drive source impedance. See
“Determining the FM Bandwidth of a Wideband Varactor
Tuned VCO” application note.
Package bottom has an exposed metal paddle that
must also be RF & DC grounded.
9
VCOs & PLOs - SMT
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
Order On-line at www.hittite.com
9 - 169
9
HMC586LC4B
v00.0206
AMPLIFIER, 4.0 - 8.0 GHz
Evaluation PCB
VCOs & PLOs - SMT
9 - 170
List of Materials for Evaluation PCB 108648
Item Description
J1 PCB Mount SMA RF Connector, Johnson
J2 PCB Mount SMA Connector, SRI
J3 DC Header
C1 1000 pF Capacitor, 0402 Pkg.
C2 4.7 μF Capacitor, Tantalum
U1 HMC5 86LC4B VCO
[2]
PCB
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
108646 Eva l Bo ard
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
Order On-line at www.hittite.com
The circuit board used in the  nal application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed ground paddle should be connected directly to the ground plane similar to that shown. A suf cient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request.
[1]
Notes:
HMC586LC4B
v00.0206
AMPLIFIER, 4.0 - 8.0 GHz
9
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250 -3373
Order On-line at www.hittite.com
VCOs & PLOs - SMT
9 - 171
Loading...