CSD-A510
LH(S),EZ(S),K(S)
CSD-A519
LH1J(S)
SERVICE MANUAL
COMPACT DISC RADIO
CASSETTE RECORDER
This Service Manual is the "Revision Publishing" and replaces "Simple Manual"
CSD-A510 LH(S)(S/M Code No. 09-003-343-2T1)
CSD-A510 EZ(S),K(S)/A519 LH1J(S)(S/M Code No. 09-003-343-2T2).
BASIC TAPE MECHANISM : TN-21ZVC-2000
BASIC CD MECHANISM : DA11T3C
S/M Code No. 09-003-343-2R1
REVISION
DATA
LH, HA MODELS
SPECIFICATIONS
K MODEL
Design and specifications are subject to change without
•
notice
.
EZ MODEL
Design and specifications are subject to change without
•
notice
.
Design and specifications are subject to change without
•
notice
.
2
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs laser. Therefore, be sure to follow carefully the
instructions below when servicing.
WARNING!
WHEN SERVICING, DO NOT APPROACH THE LASER EXIT
WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO
CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE
FROM A DISTANCE OF MORE THAN 30cm FROM THE
SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL
PICK-UP BLOCK.
Caution: Invisible laser radiation when
open and interlocks defeated avoid exposure to beam.
Advarsel:Usynling laserståling ved åbning,
når sikkerhedsafbrydere er ude af funktion.
Undgå udsættelse for stråling.
VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än vad som specificeras i
denna bruksanvising, kan användaren utsättas för osynling
laserstrålning, som överskrider gränsen för laserklass 1.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
ATTENTION
L'utilisation de commandes, réglages ou procédures autres que
ceux spécifiés peut entraîner une dangereuse exposition aux
radiations.
ADVARSEL!
Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude
af funktion. Undgå udsættelse for stråling.
This Compact Disc player is classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT label is located on the rear
exterior.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
Precaution to replace Optical block
(SF-P101NR)
Body or clothes electrostatic potential could ruin
laser diode in the optical block. Be sure ground
body and workbench, and use care the clothes
do not touch the diode.
1) After the connection, remove solder shown in
the right figure.
PICK UP ASSY
SF-P101NR
Solder
1
16
TO/FROM CD C.B
3
ELECTRICAL MAIN PARTS LIST
REF. NO PART NO. KANRI DESCRIPTION
IC
87-A20-955-010 IC,LA1828
87-A21-064-010 IC,LA4227
87-A21-520-040 C-IC,M61509FP
87-A20-446-010 C-IC,LA9241ML
87-A20-459-010 C-IC,LC78622ED
87-A21-093-010 IC,LA6541D
8A-CD9-610-010 C-IC,LC865516A-5K51
87-A21-431-010 IC,BA4560N
TRANSISTOR
89-327-143-080 TR,2SC2714 (0.1W)
87-026-447-080 TR,2SC1740S R
87-026-463-080 TR,2SA933S (0.3W)
87-026-213-080 CHIP-TR,DTC114YK
89-112-965-080 TR,2SA1296 (0.75W)
87-026-291-080 TR,DTC124XS
89-213-702-080 TR,2SB1370E
87-026-462-080 TR,2SC1740 S(RS 0.3W)
89-318-154-080 TR,2SC1815 (0.4W)
89-109-332-380 TR,2SA933RS
89-113-187-080 TR,2SA1318TU
87-026-295-080 TR,DTC144TK
89-317-403-080 TR,2SC1740S
87-026-239-080 TR,DTC114TK (0.2W)
87-026-464-080 TR,DTC114TS (0.3W)
DIODE
87-020-465-080 DIODE,1SS133 (110MA)
87-A40-128-080 C-VARI-CAP,HVU202A
87-027-607-080 ZENER,HZ7B3L
87-070-345-080 DIODE,IN4148
87-A40-648-080 ZENER,MTZJ8.2A
87-017-978-080 DIODE,1N4003
87-027-702-080 DIODE,ZENER HZ6C2L (200MA)
87-A40-465-010 DIODE,FR202
MAIN C.B
C211 87-A11-603-080 CAP, S 0.15-16
C212 87-A11-603-080 CAP, S 0.15-16
C215 87-016-460-080 C-CAP,S 0.22-16 B
C216 87-016-460-080 C-CAP,S 0.22-16 B
C231 87-010-213-080 C-CAP,S 0.015-50 B
C232 87-010-213-080 C-CAP,S 0.015-50 B
C233 87-A10-201-080 C-CAP,S0.33-16 KB
C234 87-A10-201-080 C-CAP,S0.33-16 KB
C235 87-016-669-080 C-CAP,S 0.1-25 K B
C236 87-016-669-080 C-CAP,S 0.1-25 K B
C237 87-010-371-080 CAP, ELECT 470-50V
C239 87-010-197-080 CAP, CHIP 0.01 DM
C240 87-010-197-080 CAP, CHIP 0.01 DM
C247 87-010-401-080 CAP, ELECT 1-50V
C248 87-010-401-080 CAP, ELECT 1-50V
C310 87-010-248-080 CAP, ELECT 220-10V
C316 87-010-263-080 CAP,E 100-10
C317 87-010-197-080 CAP, CHIP 0.01 DM
C801 87-010-248-080 CAP, ELECT 220-10V
C805 87-012-365-080 C-CAP,S 0.027-25VBK
C806 87-012-365-080 C-CAP,S 0.027-25VBK
C807 87-010-405-080 CAP, ELECT 10-50V
C808 87-010-405-080 CAP, ELECT 10-50V
C809 87-010-401-080 CAP, ELECT 1-50V
C810 87-010-401-080 CAP, ELECT 1-50V
C811 87-010-178-080 CHIP CAP 1000P
C812 87-010-178-080 CHIP CAP 1000P
C816 87-010-180-080 C-CER 1500P
C817 87-010-180-080 C-CER 1500P
NO.
REF. NO PART NO. KANRI DESCRIPTION
C821 87-010-401-080 CAP, ELECT 1-50V
C822 87-010-401-080 CAP, ELECT 1-50V
C823 87-010-178-080 CHIP CAP 1000P
C824 87-010-178-080 CHIP CAP 1000P
C829 87-010-178-080 CHIP CAP 1000P
C830 87-010-178-080 CHIP CAP 1000P
C833 87-018-195-080 CAP, CER 1200P-16V
C834 87-010-248-080 CAP, ELECT 220-10V
C835 87-010-322-080 C-CAP,S 100P-50 CH
C836 87-010-322-080 C-CAP,S 100P-50 CH
C843 87-010-197-080 CAP, CHIP 0.01 DM
C844 87-018-124-080 CAP, CER 270P-50V
C845 87-010-178-080 CHIP CAP 1000P
C846 87-010-263-080 CAP, ELECT 100-10V
C851 87-010-186-080 CAP,CHIP 4700P
C852 87-010-178-080 CHIP CAP 1000P
C853 87-018-211-080 CAP, CER 0.01-50<LH<S>>
C853 87-A11-145-080 CAP,TC U 0.01-50 Z F<EXCEPT LH<S>>
CN201 87-099-018-010 CONN,16P
CN801 87-A60-110-010 CONN,4P V S2M-4W
CNA302 8A-CD9-629-010 CONN ASSY,6P MA-TU
CNA801 8A-CD9-630-010 CONN ASSY, 4P RPH
L801 87-007-342-010 COIL,OSC 85K BIAS
SW801 8Z-CD9-609-010 SW,SL 1-6-2 PS62D01
CD C.B
C30 87-010-260-080 CAP, ELECT 47-25V
C261 87-010-402-080 CAP, ELECT 2.2-50V
C262 87-010-402-080 CAP, ELECT 2.2-50V
C263 87-010-178-080 CHIP CAP 1000P
C264 87-010-178-080 CHIP CAP 1000P
C265 87-010-263-080 CAP, ELECT 100-10V
C266 87-010-263-080 CAP, ELECT 100-10V
C267 87-010-112-080 CAP, ELECT 100-16V
C268 87-010-112-080 CAP, ELECT 100-16V
C271 87-010-237-080 CAP, ELECT 1000-16V
C272 87-010-237-080 CAP, ELECT 1000-16V
C278 87-010-405-080 CAP, ELECT 10-50V
C279 87-010-385-080 CAP, ELECT 220-25V
!
C301 87-016-495-000 CAP,E 3300-25 M SMG
C306 87-010-404-080 CAP, ELECT 4.7-50V
C307 87-010-401-080 CAP, ELECT 1-50V
C308 87-010-221-080 CAP, ELECT 470-10V
C311 87-010-263-080 CAP, ELECT 100-10V
C312 87-010-385-080 CAP, ELECT 220-25V
C321 87-010-197-080 CAP, CHIP 0.01 DM
C322 87-010-263-080 CAP, ELECT 100-10V
C325 87-010-405-080 CAP, ELECT 10-50V
C401 87-010-403-080 CAP, ELECT 3.3-50V
C402 87-010-197-080 CAP, CHIP 0.01 DM
C403 87-010-263-080 CAP, ELECT 100-10V
C404 87-010-248-080 CAP, ELECT 220-10V
C405 87-010-197-080 CAP, CHIP 0.01 DM
C406 87-010-374-080 CAP, ELECT 47-10V
C407 87-010-178-080 CHIP CAP 1000P
C408 87-010-198-080 CAP, CHIP 0.022
C409 87-010-248-080 CAP, ELECT 220-10V
C410 87-010-263-080 CAP, ELECT 100-10V
C411 87-A11-177-080 C-CAP,S 0.15-16 K B
C412 87-010-401-080 CAP, ELECT 1-50V
C413 87-016-369-080 C-CAP,S 0.033-25 B K
C414 87-010-405-080 CAP, ELECT 10-50V
C416 87-010-545-080 CAP, ELECT 0.22-50V
C417 87-012-157-080 C-CAP,S 330P-50 CH
C418 87-010-213-080 C-CAP,S 0.015-50 B
C419 87-A11-608-080 C-CAP,S 0.33-25 K B
C420 87-016-369-080 C-CAP,S 0.033-25 B K
C421 87-A11-177-080 C-CAP,S 0.15-16 K B
C422 87-010-183-080 C-CAP,S 2700P-50 B
NO.
4
REF. NO PART NO. KANRI DESCRIPTION
C423 87-010-956-080 CHIP-CAP,S 0.068-25B
C424 87-010-993-080 C-CAP,S 0.056-25 B
C425 87-010-176-080 C-CAP,S 680P-50 SL
C426 87-A11-608-080 C-CAP,S 0.33-25 K B
C428 87-010-197-080 CAP, CHIP 0.01 DM
C429 87-010-186-080 CAP,CHIP 4700P
C430 87-012-156-080 C-CAP,S 220P-50 CH
C431 87-010-545-080 CAP, ELECT 0.22-50V
C432 87-010-374-080 CAP, ELECT 47-10V
C433 87-010-401-080 CAP, ELECT 1-50V
C434 87-010-184-080 CHIP CAPACITOR 3300P(K)
C435 87-010-197-080 CAP, CHIP 0.01 DM
C436 87-010-374-080 CAP, ELECT 47-10V
C437 87-010-404-080 CAP, ELECT 4.7-50V
C438 87-016-669-080 C-CAP,S 0.1-25 K B
C439 87-010-178-080 CHIP CAP 1000P
C440 87-010-145-080 C-CAP, S 1P-50 C CH
C441 87-010-197-080 CAP, CHIP 0.01 DM
C442 87-010-312-080 C-CAP,S 15P-50 CH
C445 87-012-368-080 C-CAP,S 0.1-50 F
C446 87-012-368-080 C-CAP,S 0.1-50 F
C447 87-012-368-080 C-CAP,S 0.1-50 F
C448 87-010-315-080 C-CAP,S 27P-50 CH
C450 87-012-140-080 CAP 470P
C451 87-012-156-080 C-CAP,S 220P-50 CH
C455 87-010-247-080 CAP, ELECT 100-50V
C457 87-010-312-080 C-CAP,S 15P-50 CH
C458 87-010-312-080 C-CAP,S 15P-50 CH
C459 87-010-263-080 CAP, ELECT 100-10V
C460 87-015-819-080 CAPACITOR,0.01
C461 87-010-197-080 CAP, CHIP 0.01 DM
C462 87-010-248-080 CAP, ELECT 220-10V
C463 87-010-197-080 CAP, CHIP 0.01 DM
C465 87-010-404-080 CAP, ELECT 4.7-50V
C466 87-012-368-080 C-CAP,S 0.1-50 F
C467 87-010-263-080 CAP, ELECT 100-10V
C469 87-012-154-080 C-CAP,S 150P-50 CH
C470 87-010-544-080 CAP, ELECT 0.1-50V
C471 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C472 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C473 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C474 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z
C475 87-010-197-080 CAP, CHIP 0.01 DM
C476 87-010-236-080 CAP,E 1000-10 SME
C477 87-010-197-080 CAP, CHIP 0.01 DM
C478 87-010-263-080 CAP, ELECT 100-10V
C479 87-010-197-080 CAP, CHIP 0.01 DM
C480 87-010-221-080 CAP, ELECT 470-10V
C481 87-010-405-080 CAP, ELECT 10-50V
C482 87-010-405-080 CAP, ELECT 10-50V
C483 87-012-156-080 C-CAP,S 220P-50 CH
C484 87-012-156-080 C-CAP,S 220P-50 CH
C489 87-012-368-080 C-CAP,S 0.1-50 F
C490 87-012-368-080 C-CAP,S 0.1-50 F
C491 87-010-197-080 CAP, CHIP 0.01 DM
C492 87-010-221-080 CAP, ELECT 470-10V
C494 87-010-197-080 CAP, CHIP 0.01 DM
C495 87-016-669-080 C-CAP,S 0.1-25 K B
C501 87-012-368-080 C-CAP,S 0.1-50 F
C502 87-010-322-080 C-CAP,S 100P-50 CH
C503 87-010-322-080 C-CAP,S 100P-50 CH
C504 87-010-322-080 C-CAP,S 100P-50 CH
C505 87-010-322-080 C-CAP,S 100P-50 CH
C506 87-010-322-080 C-CAP,S 100P-50 CH
C510 87-016-669-080 C-CAP,S 0.1-25 K B
C831 87-010-198-080 CAP, CHIP 0.022
CN202 8A-CH4-689-010 CONN,3P V 2.5
CN205 87-A60-109-010 CONN,2P V S2M-2W
CN301 8A-CH4-689-010 CONN,3P V 2.5
CN401 87-A60-424-010 CONN,16P V TOC-B
NO.
REF. NO PART NO. KANRI DESCRIPTION
CN403 87-099-201-010 CONN,8P 6216 H
CN802 8A-CH4-687-010 CONN,4P V 2.5
CNA205 8A-CD9-631-010 CONN ASSY, 2P DOOR
CNA402 8A-CD9-625-010 CONN ASSY,6P CD-ME
CNA802 8A-CD9-631-010 CONN ASSY, 4P TP-ME
L401 87-003-102-080 COIL, 10UH
L404 87-003-152-080 COIL, 100UH
!
R840 87-029-124-010 RES,FUSE 2.2-1/4
SFR430 87-024-437-080 SFR100K,RH063EC
SW205 87-036-389-010 SW, PUSH 1-1-1 R8120125
X401 8Z-CD5-633-010 VIB, CER16.93MHZ FCR16.93M2
FRONT C.B
C601 87-010-313-080 CAP, CHIP 18P
C602 87-010-315-080 C-CAP,S 27P-50 CH
C603 87-010-319-080 C-CAP,S 56P-50 CH
C604 87-010-317-010 CHIP CAP,S 39P CH
C605 87-010-264-040 CAP,E 100-10 5L
C606 87-012-368-080 C-CAP,S 0.1-50 F
C607 87-015-779-010 CHIP CAPACITOR, 0.01
C608 87-010-401-080 CAP, ELECT 1-50V
C609 87-010-400-080 CAP, ELECT 0.47-50V
C611 87-A10-189-040 CAP,E 220-10 M5L
C613 87-012-368-080 C-CAP,S 0.1-50 F
C614 87-010-312-080 C-CAP,S 15P-50 CH
C617 87-012-368-080 C-CAP,S 0.1-50 F
C618 87-018-209-080 CAP,TC U 0.1-50 ZF
C620 87-015-819-080 C-CAP,0.01-50 K B
C621 87-015-819-080 C-CAP,0.01-50 K B
C622 87-015-779-010 CHIP CAPACITOR, 0.01
C623 87-015-779-010 CHIP CAPACITOR, 0.01
C624 87-015-779-010 CHIP CAPACITOR, 0.01
C625 87-015-779-010 CHIP CAPACITOR, 0.01
C626 87-015-779-010 CHIP CAPACITOR, 0.01
C627 87-015-779-010 CHIP CAPACITOR, 0.01
C628 87-018-209-080 CAP,TC U 0.1-50 ZF UP050
C629 87-018-119-080 CAP,TC U 100P-50 K B UP050
C630 87-018-119-080 CAP,TC U 100P-50 K B UP050
C631 87-018-119-080 CAP,TC U 100P-50 K B UP050
C632 87-018-119-080 CAP,TC U 100P-50 K B UP050
CN601 87-099-033-010 CONN,16P 6216H
CN602 87-099-201-010 CONN,8P 6216 H
L601 87-003-102-080 COIL, 10UH
L602 87-003-147-080 COIL,22UH J LAL02
L603 87-005-798-010 COIL,1.0UH J LAL02
L604 87-005-798-010 COIL,1.0UH J LAL02
L606 87-003-149-080 COIL,47UH J LAL02
LED601 88-CD6-630-010 LED,934ID RED
LED602 88-CD6-630-010 LED,934ID RED
LED603 88-CD6-630-010 LED,934ID RED
LED608 88-CD6-630-010 LED,934ID RED
LED610 88-CD6-631-010 LED,934GD GRN
LED611 87-CD8-616-010 LED,SA36-11 HWA-11.0
S601 87-A90-696-080 SW,TACT TS2103-03-430
S602 87-A90-696-080 SW,TACT TS2103-03-430
S603 87-A90-696-080 SW,TACT TS2103-03-430
S604 87-A90-696-080 SW,TACT TS2103-03-430
S605 87-A90-696-080 SW,TACT TS2103-03-430
S609 87-A90-696-080 SW,TACT TS2103-03-430
S611 87-A90-696-080 SW,TACT TS2103-03-430
S614 87-A90-696-080 SW,TACT TS2103-03-430
S615 87-A90-696-080 SW,TACT TS2103-03-430
X601 87-030-273-010 VIB,XTAL 32.768K5PPM
X602 87-030-376-080 VIB,CER CSA5.76MG200
TUNER C.B
C1 87-010-314-080 C-CAP,S 22P-50V
NO.
5
REF. NO PART NO. KANRI DESCRIPTION
C2 87-010-316-080 C-CAP,S 33P-50 CH
C3 87-010-314-080 C-CAP,S 22P-50V
C4 87-010-322-080 C-CAP,S 100P-50 CH
C5 87-010-378-080 CAP, ELECT 10-16V
C7 87-012-156-080 C-CAP,S 220P-50 CH
C8 87-010-197-080 CAP, CHIP 0.01 DM
C9 87-010-311-080 CAP 12P
C10 87-010-197-080 CAP, CHIP 0.01 DM
C11 87-010-152-080 C-CAP,S 8P-50 D CH
C12 87-010-314-080 C-CAP,S 22P-50V
C13 87-010-322-080 C-CAP,S 100P-50 CH
C14 87-010-148-080 C-CAP,S 4P-50 C CH
C15 87-016-669-080 C-CAP,S 0.1-25 K B
C16 87-010-178-080 CHIP CAP 1000P
C17 87-016-669-080 C-CAP,S 0.1-25 K B
C18 87-010-197-080 CAP, CHIP 0.01 DM
C18 87-010-188-080 CAP,CHIP 6800P<K<S>,EZ<S>>
C19 87-016-669-080 C-CAP,S 0.1-25 K B
C20 87-010-400-080 CAP, ELECT 0.47-50V
C21 87-010-403-080 CAP, ELECT 3.3-50V
C22 87-010-197-080 CAP, CHIP 0.01 DM
C24 87-A11-569-080 C-CAP,S 0.012-50 K B
C24 87-010-189-080 C-CAP,S 8200P-50 K B<K<S>,EZ<S>>
C25 87-010-189-080 C-CAP,S 8200P-50 K B<K<S>,EZ<S>>
C25 87-A11-569-080 C-CAP,S 0.012-50 K B
C26 87-012-358-080 C-CAP,S 0.47-10 Z F
C27 87-012-358-080 C-CAP,S 0.47-10 Z F
C28 87-010-992-080 C-CAP,S 0.047-25 B
C29 87-010-992-080 C-CAP,S 0.047-25 B
C30 87-010-248-080 CAP, ELECT 220-10V
C31 87-010-379-080 CAP, ELECT 22-16V
C32 87-010-197-080 CAP, CHIP 0.01 DM
C33 87-010-197-080 CAP, CHIP 0.01 DM
C34 87-010-197-080 CAP, CHIP 0.01 DM
C35 87-010-197-080 CAP, CHIP 0.01 DM
C36 87-010-263-080 CAP, ELECT 100-10V
C37 87-010-197-080 CAP, CHIP 0.01 DM
C40 87-010-329-080 C-CAP,S 6P-50 D UJ<K<S>,EZ<S>>
C41 87-010-321-080 CHIP CAPACITOR,82P(J)<K<S>,EZ<S>>
C42 87-010-150-080 C-CAP,S 6P-50 CH<K<S>,EZ<S>>
C44 87-012-140-080 CAP 470P<K<S>,EZ<S>>
C51 87-010-197-080 CAP, CHIP 0.01 DM
C56 87-010-327-080 C-CAP,S 4P-50 C UJ
C92 87-010-178-080 CHIP CAP 1000P
CF1 87-A90-128-010 FLTR,AM IF CFAL-455
CF2 87-008-261-010 FILTER, SFE10.7MA5-A
CF3 87-008-261-010 FILTER, SFE10.7MA5-A
CN2 87-A60-116-010 CONN,6P H S2M-6WR
L2 87-A50-560-010 COIL,FM BPF(ACD)
L3 8A-CD9-660-010 BAR-ANT,MW 2B-ACD(COI)
L3 8A-CD9-661-010 BAR-ANT,MW/LW 3B-ACD(COI)
L4 87-A50-562-010 COIL,FM RF EX(ACD)
L5 87-A50-564-010 COIL,FM OSC EX(ACD)
L6 87-A50-337-010 COIL,AM OSC (TOKO)
L7 87-A50-579-010 COIL,AM IFT(ACD)
NO.
<LH<S>,519LH1J<S>>
<LH<S>,519LH1J<S>>
<LH<S>,519LH1J<S>>
<LH<S>,519LH1J<S>>
<LH<S>,519LH1J<S>>
<K<S>,EZ<S>>
<LH<S>,519LH1J<S>>
REF. NO PART NO. KANRI DESCRIPTION
L8 87-A50-335-010 COIL,FM IFT (TOKO)
L9 87-A50-577-010 COIL,FM DET(ACD)
L10 87-005-849-080 COIL,10UH(CECS)
L16 87-A50-569-010 COIL,LW OSC-ACD(COI)<K<S>,EZ<S>>
L17 87-A50-337-010 COIL,AM OSC (TOKO)<K<S>,EZ<S>>
PVC1 87-A91-635-010 TUN-CAP,20P-140P E-ACD
PVC1 87-A91-167-010 TUN-CAP,20P-160P FA-22125 N000
SW1 87-A91-548-010 SW,SL-2-3 SK23E01G06
SW1 87-A91-549-010 SW,SL-6-4 SK64D01G06<K<S>,EZ<S>>
TC5 87-011-253-080 TRIMER,30P LAR<K<S>,EZ<S>>
TC6 87-011-253-080 TRIMMER,CER 30P 4.0X4.5 ECR
H.P. C.B
CN101 8A-CD9-628-010 CONN ASSY,3P MA-HP
CN102 87-A60-685-010 CONN,4P H WHT EH
HP1 87-A60-569-010 JACK,HTJ-035-18
BATT1 C.B
C901 87-010-192-080 C-CAP,S 0.022-50 F
C902 87-010-192-080 C-CAP,S 0.022-50 F
C903 87-010-192-080 C-CAP,S 0.022-50 F
C904 87-010-192-080 C-CAP,S 0.022-50 F
CNA901 8A-CD9-627-010 CONN ASSY,3P PWR
!
PR901 87-A90-092-080 PROTECTOR,2.5A 491
SP901 87-CD6-213-010 SPR-C,BATT (-)
SP902 87-CD6-213-010 SPR-C,BATT (-)
BATT2 C.B
SP903 87-CD6-213-010 SPR-C,BATT (-)
SP904 87-CD6-213-010 SPR-C,BATT (-)
MOTOR C.B
M2 9X-262-576-910 MOTOR GEAR ASSY
PIN3 91-564-722-110 CONNECTOR 6P
SW1 91-572-085-120 LEAF SW
KEY C.B
S606 87-A90-696-080 SW,TACT TS2103-03-430
S607 87-A90-696-080 SW,TACT TS2103-03-430
S608 87-A90-696-080 SW,TACT TS2103-03-430
VOL SEL C.B<LH<S>,519LH1J<S>>
SW901 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700
NO.
(MITSUMI<K<S>,EZ<S>>
<LH<S>,519LH1J<S>>
<LH<S>,519LH1J<S>>
<K<S>,EZ<S>>
<LH<S>,519LH1J<S>>
6
• Regarding connectors, they are not stocked as they are not the initial order items.
mono. SW
Control logic
The connectors are available after they are supplied from connector manufacturers upon the order is received.
CHIP RESISTOR PART CODE
Chip Resistor Part Coding
88
IC BLOCK DIAGRAM
IC, LA1828
IC, LA6541D
A
Resistor Code
Chip resistor
Wattage Type Tolerance
1/16W 1005 5% CJ
1/16W
1/10W
1/8W
1608
2125
3216
5%
5%
5%
Symbol
CJ
CJ
CJ
Figure
Value of resistor
Form
L
Dimensions (mm)
t
W
0.55
Resistor Code
108
118
128
LW t
1.0 0.5 0.35 104
1.6 0.8 0.45
2 1.25 0.45
3.2
1.6
: A
: A
IC, BA4560N
IC, M61509FP
87
WIRING-1 (MAIN/CD)
1
A
B
C
D
234567
8
9
10
11 12 13
14
E
F
G
H
I
J
K
109
SCHEMATIC DIAGRAM-1 (MAIN)
NM
LH
M61509FP
C-JUMPER
C-JUMPER
NM
LH MODEL
MTZJ6.8B MTZJ6.8B
J
PR1
J1
AC JACK
100 1SS133
100
NM : NO MOUNTED
K, EZ MODELS
LH
PT, E 2.5WPT, H 2.5W
PT, E 2.5W
1211
SCHEMATIC DIAGRAM-2 (CD)
1413
WIRING-2 (MOTOR)
1
A
TRANSISTOR ILLUSTRATION
234567
B
H MOTOR C.B
C
D
E
F
_
M2
+
M2
(SLED MOTOR)
SW1
(INSIDE LIMIT SW)
(SPINDLE MOTOR)
SW1
M3
ECB ECB ECB
2SA1296
2SC1815
C
B
E
2SC2714
DTC114TK
DTC114YK
DTC144TK
2SA933
2SC1740
DTC114TS
DTC124XS
BCE
2SB1370
2SA1318
G
TO B CD C.B CNA402
H
I
J
PIN3
M3
_
+
K
1615
WIRING-3 (FRONT/HP/BATT1/BATT2/KEY)
1
234567
8
9
10
11 12 13
14
CN403
B
E
LH MODEL
1
2
J VOL SEL C.B
(INSERTED PARTS)
SW901
AC VOLT AGE
SW901
110-120V 220-240V
EZ, K
MODEL
I KEY C.B
(INSERTED PARTS)
S607
POWER
STANDBY
RADIO
S608
TAPE
J1 AC
J1 AC
AC
DC
PT901
PT901
F BATT1 C.B
(INSERTED PARTS)
B A
PT
PT1
B
A
B
A
CNA901
TO B CD C.B
CN301
SP902 SP901
DRY BATTERY
R14x8
DC 12V
G BATT2 C.B
(INSERTED PARTS)
SP904 SP903
C FRONT C.B
I KEY C.B
(CHIP PARTS)
(CHIP PARTS)
S606
CD
13
12
24
25
1
3
2
1
3
1
1
2
3
3
1
48
36
37
A
E H.P. C.B
(INSERTED PARTS)
SPEAKER
L
R
B
C
D
E
F
G
S615
VOLUME
H
S614
14
1
3
TO B CD C.B
CN202
TO A MAIN C.B
CN201
15
16
HP1
PHONES
1
2
C FRONT C.B
(INSERTED PARTS)
S611
3-MODE
EQUALIZER
S609
QSOUND
TO B CD C.B
7
8
C
BCE
I
S604
SKIP/SEARCH
J
S602
S601
REPEAT
SLEEP
/OSC
LED602
REPEAT
LED610
Q-SOUND
(7 SEG LED)
56
110
LED608
OPE/BATT
LED601
RADIO
LED603
CD
S603
STOP/MEMORY
S605
PLAY/PAUSE
56
1
10
NOTE
Rxxx
ECB
K
1817
SCHEMATIC DIAGRAM-3 (FRONT/KEY)
C FRONT C.B
CD-SW
DRF
WRQ
Q610
C632 100p
C631 100p
C630 100p
C629 100p
C618
0.1
C617
0.1
CN403
RWC
CQCK
TO B CD C.B (2/2)
SQOUT
COIN
O-CD
AC 12V
O-Q SOUND
O-BEAT
I-FM ST
0-TU
O-DATA
O-P. CONT
O-MUTE
12V
CN201
TO A MAIN C.B
NC
I-SYS
U-COM 5V
D.GND
SW 8V
OPE/FWD
OPE/REV
CN601
R616 1k
R653 1k
R619 1k
R618 1k
R617 1k
R651 1k
L606 47µH
2SA933S
DIGIT SW
L604
1µH
R647
47k
R648
330
C627 0.01
C624 0.01
C625 0.01
C626 0.01
R652
10
LED611 SA36-11
DP
DIGIT
SEG DP
SEG C
SEG B
SEG A
(7 SEG LED)
C611 220/6.3
SEG D
SEG E
SEG G
SEG F
NC
C606 0.1
L603
1µH
L602 22µH
C605
100/10
C623 0.01
C622 0.01
C620 0.01
C621 0.01
O-RWC
O-DATA
O-CD LED
O-TU LED
O-TA LED
NC
SEG DP
SEG A
SEG B
SEG C
SEG D
NC
O-CQCK
SEG E
O-COIN
I-SQOUT
SEG F
SEG D
C608
O-SEG RPEAT
LC865516A-5K51
SYSTEM CONTROL
NC
C601
DTC114YK
1/50
O-DIGIT
18p
Q603
RESET
O-MUTE
XT1(IN)
X601
32.768
kHz
C602
27p
O-BEAT
NC
NC
O-P. CONT
XT2(OUT)
O-TU ON
CF1(IN)
C603
56p
C614
L605 JW
15p
C609
0.47/50
R659
100k
I-REM
O-CD ON
I-WRQ
I-DRF
O-SFT LED
O-QS LED
O-BASS LED
O-SHIFT
I-CDSW
I-MOTOR
I-KEY1
I-KEY0
VDD
CF2(OUT)
R601
1k
X602
5.76MHz
NC
NC
C604
39p
Q613
DTC114TK
CLK-SHIFT SW
R660
1k
R655 10k
R603 10k
R602 10k
C628
0.1
R604
470k
S601
R620
1k
S602
R656
1k
R621
820
DTC114TK
R650
22k
R6221kR623
S603
DTC114TK
R657
1k
Q606
Q604,606-608
LED DRIVER
1.2k
S604
Q608
R630
Q604
2SC1740S
R624
1.2k
P1-2
S605
P1-3 P2-3
R634
1.5k
R635
1.5k
R636
1.5k
Q607
DTC114TK
2.2k
R658
10
S614
I KEY C.B
R625
R626
1.5k
1.8k
S606
S607
S608
R670
1k
R627
2.2k
P2-1P2-2
S615
OPE/BAT
9341D RED
934GD GRN
RADIO
R628
3.3k
P1-1
S609
LED608
LED610
LED601
9341D RED
LED603
9341D RED
LED602
9341D RED
R629
3.9k
S611
S601
REPEAT SLEEP/OSC
S602
S603
STOP/MEMORY
S604
S605
S606
CD
SKIP/SEARCH
SKIP/SEARCH
PLAY/PAUSE
S607
POWER STANDBY/RADIO
S608
TAPE
S609
QSOUND
S611
3-MODE EQUALIZER
S614
VOLUME
VOLUME
S615
2019
SCHEMATIC DIAGRAM-4 (TUNER: LH)
FM BALANCE ADJ.
10
68k
100p
2221
WIRING-4 (TUNER: LH)
1
A
B
C
D
234567
E
F
G
H
I
J
K
23
WIRING-5 (TUNER: K, EZ)
1
A
B
C
D
234567
E
F
G
H
I
J
K
24
SCHEMATIC DIAGRAM-5 (TUNER: K, EZ)
FM BALANCE ADJ.
2625
ELECTRICAL ADJUSTMENT
1
D
TUNER C.B
2
L004
5
(LH MODEL)
PVC001
TC4 TC3
TC1TC2
19
IC001
L007
L008
63 74
B
CD C.B
IC404
SFR430
CN401
A
MAIN C.B
L003
(BAR ANT)
L006
L005
L009
23
L003
(BAR ANT)
21
D
TUNER C.B
4
TC006
3
L004
7
(K, EZ MODELS)
TC4
L008
PVC001
TC3
TC1
TC2
L007
L016 L017
L005
19
IC001
TC005
L009
85 96
#
IC801
1
CN201
CN801
L801
< TUNER SECTION >
(LH MODEL)
1. AM Freq. Range Adjustment
L006 ....................................................................... 517kHz
TC003................................................................... 1750kHz
2. AM Tracking Adjustment
L003 ....................................................................... 600kHz
TC004................................................................... 1400kHz
3. AM IF Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L007
Method: Adjust L007 so that the output level at 1400kHz
becomes maximum.
4. FM Freq. Range Adjustment
L005 .....................................................................87.0MHz
TC001................................................................. 109.0MHz
5. FM Tracking Adjustment
L004 .....................................................................88.0MHz
TC002................................................................. 108.0MHz
6. FM IF Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L008
Method: Adjust L008 so that the output level at 98.0MHz
becomes balanced.
7. FM Balance Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L009
Method: Adjust L009 so that the output level at 98.0MHz
becomes balanced.
(K, EZ MODELS)
1. LW Freq. Range Adjustment
L016 ....................................................................... 145kHz
TC005..................................................................... 295kHz
2. MW Freq. Range Adjustment
L017 ....................................................................... 515kHz
TC003................................................................... 1635kHz
3. MW Tracking Adjustment
L003 ....................................................................... 600kHz
TC004................................................................... 1400kHz
6. FM Freq. Range Adjustment
L005 .....................................................................87.4MHz
TC001................................................................. 108.3MHz
7. FM Tracking Adjustment
L004 .....................................................................88.0MHz
TC002................................................................. 108.0MHz
8. FM IF Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L008
Method: Adjust L008 so that the output level at 98.0MHz
becomes balanced.
9. FM Balance Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L009
Method: Adjust L009 so that the output level at 98.0MHz
becomes balanced.
< DECK SECTION >
10. Tape Speed Adjustment
Settings : • Test tape : TTA-100
• Test point : J251 (PHONES jack)
• Adjustment location : SFR of deck motor
Method : Play back the test tape and adjust SFR so that
the frequency counter reads 3000Hz±30Hz.
11. Head Azimuth Adjustment
Settings : • Test tape : TTA-320
• Test point : J251 (PHONES jack)
• Adjustment location : Azimuth adjustment
screw
Method : Play back the 8kHz signal of the test tape and
adjust screw so that the output becomes
maximum.
12. Bias frequncy Adjustment
L801..................................................................85kHz±0.5kHz
< CD SECTION >
13. FE Balance Adjustment
Settings : • Test point : IC401 PIN58 (VR), IC401 PIN 20
(FE)
• Adjustment location : SFR430
Method : Playback the disc and adjust SFR430 so that the
test point voltage becomes 0V.
E
H.P. C.B
PHONES
HP1
0!
M1 (TAPE MOTOR)
0
@
!
RPH
4. LW Tracking Adjustment
TC006..................................................................... 288kHz
5. AM IF Adjustment
Settings: • Test point: IC001 (LA1828) 19PIN
• Adjustment location: L007
Method: Adjust L007 so that the output level at 1400kHz
becomes maximum.
2827
PRACTICAL SERVICE FIGURE
< TUNER SECTION >
< FM SECTION >
Sensitivity: Less than 19dB (88.0MHz)
(THD 3%) Less than 18dB (98.0MHz)
Less than 18dB (108.0MHz)
Signal to Noise Ratio: LH MODEL:
(Input 60dB) More than 57dB (at 98.0MHz)
K, EZ MODELS:
More than 50dB (at 98.0MHz)
Distortion: Less than 1.5% (at 98.0MHz)
(Input 60dB)
Intermediate frequency: 10.7MHz ±0.1MHz
Stereo separation: More than 22dB (at 98MHz)
< AM/MW SECTION >
Sensitivity: Less than 45dB (at 600kHz)
(S/N 10dB) Less than 45dB (at 1000kHz)
Less than 45dB (at 1400kHz)
Distortion: Less than 3.0%
(Input 74dB)
Intermediate frequency: 455kHz±3.5kHz
< LW SECTION > (K, EZ MODELS)
Sensitivity: Less than 57dB
(S/N 10dB) (at 153/198/288kHz)
Signal to Noise Ratio: More than 24dB
(Input 74dB) (at 198kHz)
Distortion:
(Input: 74/120dB) Less than 3% (at 198kHz)
< CASSETTE SECTION >
Tape speed: 3000Hz+3%-2%
Wow & flutter: Less than 0.35% (JIS RMS)
S/N ratio: More than 35dB
Distortion: Less than 3.0% (PB)
Noise (PB): Less than 1mV
(DC, MIN)
Less than 1.2mV (AC, MIN)
Erasing Ratio (W/O FILTER): More than 45dB
29
IC DESCRIPTION
IC, LA9241ML
Pin No. Pin Name I/O Description
Pin to which external pickup photo diode is connected. RF signal is created by adding
1
FIN2
I
with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal.
10
11
12
13
14
15
2
3
4
5
6
7
8
9
FIN1
E
F
TB
TE-
TE
TESI
SCI
TH
TA
TD-
TD
JP
TO
I
Pin to which external pickup photo diode is connected.
Pin to which external pickup photo diode is connected. TE signal is created by
I
subtracting from the F pin signal.
I
Pin to which external pickup photo diode is connected.
I
DC component of the TE signal is input.
Pin to which external resistor setting the TE signal gain is connected between the TE
I
pin.
O
TE signal output pin.
TES “Track Error Sense” comparator input pin. TE signal is passed through a band-
I
pass filter then input.
I
Shock detection signal input pin.
I
Tracking gain time constant setting pin.
O
TA amplifier output pin.
Pin to which external tracking phase compensation constants are connected between
I
the TD and VR pins.
I
Tracking phase compensation setting pin.
I
Tracking jump signal (kick pulse) amplitude setting pin.
O
Tracking control signal output pin.
16
17
18
19
20
21
22
23
24
25
26
27
28
29
FD
FD-
FA
FA-
FE
FE-
AGND
SP
SPI
SPG
SP-
SPD
SLEQ
SLD
—
O
Focusing control signal output pin.
Pin to which external focusing phase compensation constants are connected between
I
the FD and FA pins.
Pin to which external focusing phase compensation constants are connected between
I
the FD– and FA– pins.
Pin to which external focusing phase compensation constants are connected between
I
the FA and FE pins.
O
FE signal output pin.
I
Pin to which external FE signal gain setting resistor is connected between the FE pin.
Analog signal GND.
O
Signal ended output of the CV+and CV- pin input signal.
I
Spndle amp input.
I
Pin to which external spindle gain setting resistor in 12 cm mode is connected.
Pin to which external spindle phase compensation constants are connected together
I
with SPD pin.
O
Spindle control signal output pin.
I
Pin to which external sled phase compensation constants are connected.
O
Sled control signal output pin.
30, 31
32, 33
34
35
SL-, SL+
JP-, JP+
TGL
TOFF
I
Sled advance signal input pin from microprocessor.
I
Tracking jump signal input pin from DSP.
I
Tracking gain control signal input from DSP. Low gain when TGL = H.
I
Tracking off control signal input pin from DSP. Off when TOFF = H.
30
Pin No. Pin Name I/O Description
36
TES
O
Pin from which TES signal is output to DSP.
37
38
39, 40
41
42
43
44
45
46
47
48
49
50
51
52
HFL
SLOF
CV–, CV+
RFSM
RFS-
SLC
SLI
DGND
FSC
TBC
NC
DEF
CLK
CL
DAT
O
O
O
—
O
—
O
“High Frequency Level” is used to judge whether the main beam position is on top of
bit or on top of mirror.
I
Sled servo off control input pin.
I
CLV error signal input pin from DSP.
RF output pin.
RF gain setting and EFM signal 3T compensation constant setting pin together with
I
RFSM pin.
“Slice Level Control” is the output pin which controls the RF signal data slice level by
DSP.
I
Input pin which control the data slice level by the DSP.
Digital system GND.
Output pin to which external focus search smoothing capacitor is connected.
I
“Tracking Balance Control” EF balance variable range setting pin.
No connection.
Disc defect detector output pin.
I
Reference clock input pin. 4.23 MHz of the DSP is input.
I
Microprocessor command clock input pin.
I
Microprocessor command data input pin.
53
54
55
56
57
58
59
60
61
62
63
64
CE
DRF
FSS
VCC2
REFI
VR
LF2
PH1
BH1
LDD
LDS
VCC1
I
Microprocessor command chip enable input pin.
O
“Detect RF” RF level detector output.
I
“Focus Search Select” focus search mode (± search/+ search) select pin.
—
Servo system and digital system Vcc pin.
—
Pin to which external bypass capacitor for reference voltage is connected.
O
Reference voltage output pin.
I
Disc defect detector time constant setting pin.
I
Pin to which external capacitor for RF signal peak holding is connected.
I
Pin to which external capacitor for RF signal bottom holding is connected.
O
APC circuit output pin.
I
APC circuit input pin.
—
RF system Vcc pin.
31
IC, LC78622ED
Pin No. Pin Name I/O Description
1
DEFI
I
Defect sense signal (DEF) input pin. (Connect to 0V when not used).
2
3
4
5
6
7
8
9
10
11
12, 13
14
15
16
17
18
TAI
PDO
VVSS
ISET
VVDD
FR
VSS
EFMO
EFMIN
T2
CLV+, CLK-
___
V/P
HFL
TES
TOFF
TGL
I
O
—
For PLL.
I
—
I
—
Digital system GND. Be sure to connect to 0V.
O
For slice level control.
I
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
O
Disc motor control output. Three level output is possible using command.
Rough servo or phase control automatic selection monitoring output pin. Rough servo
O
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Phase comparator output pin to control external VCO.
GND pin for built-in VCO. Be sure to connect to 0V.
Pin to which external resistor adjusting the PD0 output current.
Power supply pin for built-in VCO.
Pin for VCO frequency range adjustment.
EFM signal output pin.
EFM signal input pin.
at H. Phase servo at L.
I
Track detect signal input pin. Schmidt input.
I
Tracking error signal input pin. Schmidt input.
O
Tracking OFF output pin.
O
Tracking gain selection output pin. Gain boost at L.
19, 20
21
22
23
24
25
26
27
28
29
30
31
32, 33
34
35
36
37
JP+, JP-
PCK
FSEQ
VDD
SL+
SL-
CONT3 (NC)
PUIN
_______
RW
EMPH
C2F
DOUT
T3, T4
N.C.
MUTEL
LVDD
LCHO
O
Track jump control signal output pin. Three level output is possible using command.
O
EFM data playback clock monitoring pin 4.3218 MHz when phase is locked in.
Sync signal detection output pin. H when the sync signal which is detected from EFM
O
signal and thesync signal which is internally generated agree.
—
Digital system power supply pin.
O
Moves the sled to outer circumference.
O
Moves the sled to inner circumference.
—
Not connected.
I
CD pickup inner switch detection.
O
Read, wright signal.
O
De-emphasis monitor output pin. De-emphasis disc is being played back at H.
O
C2 flag output pin.
O
DIGITAL OUT output pin. (EIAJ format).
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
—
Not used. Set the pin to open.
O
—
L-channel 1-bit DAC.
O
L-channel mute output pin.
L-channel power supply pin.
L-channel output pin.
38
39
40
41
42
LVSS
RVSS
RCHO
RVDD
MUTER
—
—
O
R-channel 1-bit DAC.
—
O
L-channel GND. Be sure to connect to 0V.
R-channel GND. Be sure to connect to 0V.
R-channel output pin.
R-channel power supply pin.
R-channel mute output pin.
32
Pin No. Pin Name I/O Description
43
XVDD
—
Crystal oscillator power supply pin.
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
XOUT
XIN
XVSS
SBSY
EFLG
PW
SFSY
SBCK
FSX
WRQ
RWC
SQOUT
COIN
___________
CQCK
RES
T11
O
Pin to which external 16.9344 MHz crystal oscillator is connected.
I
—
Crystal oscillator GND pin. Be sure to connect to 0V.
O
Subcode block sync signal output pin.
O
C1, C2, single and dual correction monitoring pin.
O
Subcode P, Q, R, S, T, U and W output pin.
O
Subcode frame sync signal output pin. Falls down when subcode enters standby.
Subcode read clock input pin. Schmidt input. (Be sure to connected to 0V when not
I
in use.)
Pin outputting the 7.35 kHz sync signal which is generated by dividing frequency of
O
crystal oscillator.
O
Subcode Q output standby output pin.
I
Read/write control input pin. Schmidt input.
O
Subcode Q output pin.
I
Command input pin from microprocessor.
I
Command input read clock or subcode read input clock from SQOUT pin
I
LC78622 reset input pin. Set this pin to L once when the main power is turned on.
O
Test signal output pin. Use this pin as open (normally L output).
60
61
62
63
64
16M
4.2M
T5
______
CS
T1
O
16.9344 MHz output pin.
O
4.2336 MHz output pin.
I
Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V.
Chip select signal input pin with built-in pull-down resistor. Be sure to connect to 0V
I
while it is not controlling.
I
Test signal input pin without built-in pull-down resistor. Be sure to connect to 0V.
33
IC, LC865516A-5K51
Pin No. Pin Name I/O Description
1
SEG E
O
SEG E control.
10
11
12
13
14
15
16
17
18
2
3
4
5
6
7
8
9
SEG F
SEG G
NC
______________
RESET
XT1 (IN)
NC
XT2 (OUT)
GND
CF1 (IN)
CF2 (OUT)
VDD
I-KEY0
I-KEY1
I-MOTOR
I-CD SW
O-SHIFT
NC
O
SEG F control.
O
SEG G control.
—
Not connected.
I
Micro processor reset input
I
Connected to an external 32.768 kHz crystal oscillator.
—
Not connected.
O
Connected to an external 32.768 kHz crystal oscillator.
—
GND.
I
Connected to an external 5.76 MHz ceramic filter.
O
Connected to an external 5.76 MHz ceramic filter.
—
Microprocessor power supply (+5V).
I
Key AD input. (AD)
I
Key AD input. (AD)
I
Deck status input. (AD)
I
CD door switch status input.
O
Main clock shift output.
—
Not connected.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
O-BASS LED
O-QS LED
O-SFT LED
I-DRF
I-WRQ
NC
I-REM
O-CD ON
O-TU ON
O-P.CONT
NC
O-BEAT
O-MUTE
O-DIGIT
O-SEG RPEAT
O-COIN
I-SQOUT
O
BASS LED ON/OFF control output. (Not connected)
O
Q sound LED ON/OFF control output. (Not connected)
—
Not connected.
I
CD RF level detection input.
I
CD subcode Q standby input.
—
Not connected.
—
Remote control input.
O
CD power control output.
O
TU power control output.
O
The main power supply control output.
—
Not connected.
O
Beat control.
O
Main mute output.
O
7-segment LED power supply control output.
O
REPEAT LED ON/OFF control output.
O
CD command output.
I
CD subcode Q input.
36
37
38
39
40
41
O-CQCK
O-RWC
O-DATA
O-CD LED
O-TU LED
O-TA LED
O
CD command/CLK for subcode.
O
CD read/write control output.
O
Data output to M62349FP.
O
LED ON/OFF control output for the CD function.
O
LED ON/OFF control output for the TU function.
O
LED ON/OFF control output for the TA function. (Not connected)
34
Pin No. Pin Name I/O Description
42
NC
—
Not connected.
43
44
45
46
47
48
SEG DP
SEG A
SEG B
SEG C
SEG D
NC
—
O
O
O
O
O
SEG DP control.
SEG A control.
SEG B control.
SEG C control.
SEG D control.
Not connected.
35
MECHANICAL PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 8Z-CL7-107-010 BADGE,AIWA SILVER
2 8A-CD8-007-010 WINDOW,CASS
3 8A-CD8-006-010 BOX,CASS
4 8A-CD8-207-010 SPR-T,CASS
5 8A-CD8-209-010 HLDR,TRANS
6 8A-CD8-018-010 PANEL,FR L
7 8A-CD8-043-010 WINDOW,DISPLAY EX
8 88-CD8-622-010 SPKR,F 77 7OHM 3W
9 8A-CD8-210-010 HLDR,SPKR A
10 8A-CD8-211-010 HLDR,SPKR B
11 84-CD5-215-010 GEAR
12 8A-CD8-021-010 CHAS,CASS
13 8A-CD9-633-010 CONN ASSY,4P SP
14 8A-CD9-626-010 CONN ASSY,2P DOOR
15 8A-CD8-022-010 PANEL,FR R
16 8A-CD8-016-010 KEY,CONTROL CD
17 8A-CD8-014-010 KEY,VOL
18 8A-CD8-017-010 KEY,QSOUND
19 8A-CD8-206-010 HLDR,LED
20 8A-CD8-015-010 KEY,FUNC
21 8A-CD8-011-010 KEY,CASS SET
22 8A-CD8-213-010 SPR-P,REC
23 M8-ZZK-E90-070 DA11T3C
24 8A-CD9-622-010 FF-CABLE, 8P CD-FR
25 8A-CD9-621-010 FF-CABLE, 16P CD-RF
26 8Z-CDB-169-010 PANEL,CD SANYO
27 88-CD9-211-210 RING,CHUCK
28 8Z-CDB-170-010 BASE,CHUCK
29 87-036-368-010 MAGNET
30 84-CT5-209-010 PLATE,MAGNET
31 8Z-CH4-225-010 HLDR, CHUCK A(S)
32 8A-CD8-027-010 BOX,CD EX
33 8A-CD8-028-010 CHAS,CD EX
34 8A-CD8-008-010 HANDL,FR
35 87-036-389-010 SW,PUSH LOCK
36 8A-CD8-009-010 HANDL,REAR
37 8A-CD8-208-010 SPR-T,CD
38 84-CD5-216-010 BRACKET
!
39 8A-CD8-603-010 PT,E 2.5W<K<S>,EZ<S>>
!
39 8A-CD8-604-010 PT,H 2.5W<LH<S>,519LH1J<S>>
NO.
REF. NO PART NO. KANRI DESCRIPTION
40 8A-CD9-630-010 CONN ASSY,4P RPH
!
41 87-A60-178-010 JACK,AC E W/SW
42 87-A90-086-010 COVER,AC-SOCKET
43 88-CD8-209-010 SPR-C,BATT
44 8A-CD8-212-010 HLDR,ANT
45 8A-CD9-620-010 FF-CABLE, 16P FR-MAIN
46 8A-CD8-003-010 LID,BATT
47 8A-CD8-026-010 CABI,REAR EZ<K<S>,EZ<S>>
47 8A-CD8-024-010 CABI,REAR U<LH<S>,519LH1J<S>>
48 8Z-CH4-640-010 ANT,ROD
49 8A-CD9-631-010 CONN ASSY,4P TP-ME
50 8A-CD8-012-010 KNOB,RTRY TU
51 8A-CD8-201-010 GEAR,IDLER
52 8A-CD8-203-010 DRUM,DIAL
53 8A-CD8-202-010 LEVER,BAND
54 8A-CD8-010-010 POINTER,TU
55 8A-CD8-030-010 WINDOW,DIAL EZ<K<S>,EZ<S>>
55 8A-CD8-029-010 WINDOW,DIAL U<LH<S>,519LH1J<S>>
!
56 87-A91-369-010 SW,AC SL 2 2 2 SDKGA41700
57 8A-CD8-013-010 KNOB,SL BAND
A 87-B10-242-010 UT2+3-30 W/O CR
B 87-741-095-410 UT2+3-8 W/O SLOT
C 87-254-097-410 U+3-12 CR
D 87-741-095-410 UT2+3-8 GLD
E 87-342-074-010 UT2+2.6-8
F 87-353-076-210 VT2+2.6-12
G 87-571-032-410 VIT+2-3
H 87-WA5-253-010 W,3.3-10-0.8
I 87-751-094-410 VT2+3-6 W10SL0T
J 87-661-097-410 TAPPING SCREW, VFT1+3-12
K 87-067-566-010 TAPPING SCREW, VFTT+3-6
L 87-501-073-410 VF+2.6-6
NO.
<LH<S>,519LH1J<S>>
COLOR NAME TABLE
Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange
36
MECHANICAL EXPLODED VIEW 1/1
17
18
31
30
29
28
33
32
35
34
36
47
13
B
P.C. B
D
48
57
B
A
C
GRILLE, SPKR L
6
11
25
b
38
37
J
H
E
14
5
SHIELD
PLATE
D
24
HT-SINK
40
39
43
P.C. B
F
43
K
CHAS,TU B
E
e
P.C. B
E
a
16
7
D
8
e
9
19
B
c
D
B
38
11
20
E
E
d
P.C. B
D
TN-21ZVC-2000
12
D
27
CUSHION,
CD A
21
CUSHION,
CD A
10
26
H
E
22
P.C. B
B
23
G
P.C. B
B
I
SW COVER
E
P.C. B
A
56
44
P.C. B
41
42
D
B
51
L
50
RUBBER
FOOT
46
CHAS,TU A
53
10
a
3
4
2
1
55
b
c
d
CABI, FR EX
9
8
B
45
49
15
GRILLE, SPKR R
D
B
54
BAR, ANT
3837
52
WIRE, FASTON ASSY ANT
D
P.C. B
TAPE MECHANISM EXPLODED VIEW 1/1
F
G
1
E
2
8
10
J
L
14
b
18
19
7
36
46
47
25
9
21
20
22
23
24
c
51
26
27
28
A
6
29
LUG PLATE
52
4
3
a
15
16
17
34
35
37
TAPE MECHANISM PARTS LIST 1/1
REF. NO PART NO. KANRI DESCRIPTION
1 S1-921-030-4A0 HEAD BASE
2 S1-821-030-070 AZIMUTH SPRING
5
11
12
13
31
49
30
32
c
b
33
A
3 S1-921-030-090 PANEL P SPRING
4 S1-921-260-050 GEAR PLATE SPRING
5 S1-921-265-020 GEAR PLATE ASSY
6 S1-510-020-020 REC SPRING PLATE
7 S1-921-015-010 CHASSIS ASSY
8 S1-921-030-110 HEAD PANEL
9 S1-921-143-160 BASE ASSY
10 S1-921-141-8A0 M CONTROL SPRING
11 S1-921-260-4A0 SENSING LEVER
12 S1-921-043-100 PINCH ROLLER ARM ASSY
13 S1-921-130-010 EJECT SLIDE LEVER
14 S1-921-141-3A0 P CONTROL SPRING
15 S1-921-140-550 PAUSE LEVER(E)
16 S1-921-140-120 PAUSE LEVER SPRING
17 S1-921-140-110 PAUSE STOPPER
18 S1-921-140-150 BUTTON LEVER SPRING(B)
19 S1-821-011-590 E KICK LEVER
20 S1-921-141-070 BUTTON LEVER SPRING(A)
21 S6-401-011-490 LEAF SW MSW-1541T
22 S1-921-140-090 SWITCH ACTUATOR
23 S1-921-140-080 PUSH BUTTON ACTUATOR
24 S1-921-140-190 PLAY BUTTON LEVER
25 S1-921-030-100 MG ARM SPRING
26 S1-921-140-040 REW BUTTON LEVER
27 S1-921-140-050 FF,BUTTON REVER
28 S1-921-140-060 STOP BUTTON LEVER
29 S1-921-140-600 PAUSE BUTTON LEVER
30 S1-821-100-700 FF GEAR
31 S1-921-050-060 SENSER
32 S1-921-053-100 TAKE UP REEL ASSY
33 S1-829-100-010 PACK SPRING
34 S1-921-050-150 S REEL HUB
35 S1-921-050-220 BACK TENSION SPRING
NO.
a
C
48
C
REF. NO PART NO. KANRI DESCRIPTION
36 S1-921-140-030 REC BUTTON LEVER
37 S1-921-140-170 P.S.LEVER SPRING
38 S1-921-073-040 RF CLUTCH ASSY
39 S1-921-070-030 RF BELT
40 S1-921-260-020 CAM GEAR
41 S1-921-140-160 E ACTUATOR SPRING
42 S1-921-093-210 FLYWHEEL ASSY
43 S1-921-090-380 MAIN BELT
44 S1-921-120-590 MOTOR PULLEY
45 S6-002-030-220 MOTOR EG530AD-2B
46 S6-209-100-100 E HEAD PH-K380-MS1
47 S1-921-030-050 MG ARM
48 S1-921-140-210 REC BUTTON LEVER SPRING
49 S1-821-100-690 RECORD SAFETY LEVER
50 S1-821-128-9A0 MOTOR BRACKET
51 S1-821-010-500 PLAY BUTTON LEVER SPRING
52 S6-201-011-110 HEAD,RP7442ES-0951
A S9-P04-200-310 C TAPPING SCREW 2-3
B S1-921-120-020 MOTOR COLLER SCREW
C S9-B10-200-510 P TAPPING BIND SCREW M2-5
D S9-C07-204-510 SCREW,TAPPING(CAMERA)M2-4.5
E S9-P01-200-610 SCREW,M2-6
F S9-B01-200-310 (+)BIND SCREW M2-3
G S9-F08-200-710 AZIMUTH SCREW M2-7
H S1-921-120-030 MB SCREW
I S9-W02-300-100 P WASHER CUT 1.2-3.8-0.3
J S9-W02-500-100 P WASHER CUT 1.45-3.8-0.5
K S9-W01-400-100 P WASHER 2-3.5-0.4
L S9-W01-130-200 P WASHER 2.1-4-0.13
NO.
38
39
42
43
D
40
D
K
41
I
B
B
50
H
44
45
4039
CD MECHANISM EXPLODED VIEW 1/1
SHAFT,SLIDE
CD MECHANISM PARTS LIST 1/1
B
SF-P101NR
CHASSIS
REF. NO PART NO. KANRI DESCRIPTION
B
1
1 S2-121-A28-400 COVER GEAR
2 S2-511-A21-000 GEAR MIDDLE
3 S2-511-A21-100 GEAR,DRIVE
A S1-PN2-03R-OSE SCR PAN PCS 2-3
B 87-261-073-410 SCR S-TPG FLT 2.6-6
ALL M8-ZZK-E90-070 DA11T3C
NO.
2
A
A
3
SPINDLE
MOTOR(M3)
MOTOR C,B
ACCESSORIES/PACKAGE LIST
REF. NO PART NO. KANRI DESCRIPTION
1 8A-CD8-906-010 IB,EZ(9L)B<EZ<S>>
1 8A-CD8-905-010 IB,K(E)B<K<S>>
1 8A-CD9-902-010 IB,LH(ESP)B<LH<S>>
1 8A-CD8-940-010 IB,LH1(P)KIT<519LH1J<S>>
!
2 87-A80-036-010 AC CORD SET ASSY,E W/FLTR VOL<EXCEPT K<S>>
!
2 87-A80-034-010 AC CORD SET ASSY,K W/F MAY-BG<K<S>>
!
3 87-A90-312-010 PLUG,CONVERSION WTN-1157R1<LH<S>,519LH1J<S>>
NO.
4241
REFERENCE NAME LIST
ELECTRICAL SECTION
DESCRIPTION REFERENCE NAME
ANT ANTENNAS
C- CHIP
C-CAP CAP, CHIP
C-CAP TN CAP, CHIP TANTALUM
C-COIL COIL, CHIP
C-DI DIODE, CHIP
C-DIODE DIODE, CHIP
C-FET FET, CHIP
C-FOTR FILTER, CHIP
C-JACK JACK, CHIP
C-LED LED, CHIP
C-RES RES, CHIP
C-SFR SFR, CHIP
C-SLIDE SW SLIDE SWITCH, CHIP
C-SW SWITCH, CHIP
C-TR TRANSISTOR, CHIP
C-VR VOLUME, CHIP
C-ZENER ZENER, CHIP
CAP, CER CAP, CERA-SOL
CAP, E CAP, ELECT
CAP, M/F CAP, FILM
CAP, TC CAP, CERA-SOL
CAP, TC-U CAP, CERA-SOL SS
CAP, TN CAP, TANTALUM
CERA FIL FILTER, CERAMIC
CF FILTER, CERAMIC
DL DELAY LINE
E/CAP CAP, ELECT
FILT FILTER
FLTR FILTER
FUSE RES RES, FUSE
MOT MOTOR
P-DIODE PHOTO DIODE
P-SNSR PHOTO SENSER
P-TR PHOTO TRANSISTOR
POLY VARI VARIABLE CAPACITOR
PPCAP CAP, PP
PT POWER TRANSFORMER
PTR, RES PTR, MELF
RC REMOTE CONTROLLER
RES NF RES, NON-FLAMMABLE
RESO RESONATOR
SHLD SHIELD
SOL SOLENOID
SPKR SPEAKER
SW, LVR SWITCH, LEVER
SW, RTRY SWITCH, ROTARY
SW, SL SWITCH, SLIDE
TC CAP CAP, CERA-SOL
THMS THERMISTOR
TR TRANSISTOR
TRIMMER CAP, TRIMMER
TUN-CAP VARIABLE CAPACITOR
VIB, CER RESONATOR, CERAMIC
VIB, XTAL RESONATOR, CRYSTAL
VR VOLUME
ZENER DIODE, ZENER
MECHANICAL SECTION
DESCRIPTION REFERENCE NAME
ADHESHIVE SHEET ADHESHIVE
AZ AZIMUTH
BAR-ANT BAR-ANTENNA
BAT BATTERY
BATT BATTERY
BRG BEARING
BTN BUTTON
CAB CABINET
CASS CASSETTE
CHAS CHASSIS
CLR COLLAR
CONT CONTROL
CRSR CURSOR
CU CUSHION
CUSH CUSHION
DIR DIRECTION
DUBB DUBBING
FL FRONT LOADING
FLY-WHL FLYWHEEL
FR FRONT
FUN FUNCTION
G-CU G-CUSHION
HDL HANDOL
HIMERON CLOTH
HINGE, BAT HINGE, BATTERY
HLDR HOLDER
HT-SINK HEAT SINK
IB INSTRUCTION BOOKLET
IDLE IDLER
IND, L-R INDICATOR, L-R
KEY, CONT KEY, CONTROL
KEY, PRGM KEY, PROGRAM
KNOB, SL KNOB, SLIDE
LBL LABEL
LID, BATT LID, BATTERY
LID, CASS LID, CASSETTE
LVR LEVER
P-SP P-SPRING
PANEL, CONT PANEL, CONTROL
PANEL, FR PANEL, FRONT
PRGM PROGRAM
PULLY, LOAD MO PULLY, LOAD MOTOR
RBN RIBBON
S- SPECIAL
SEG SEGMENT
SH SHEET
SHLD-SH SHIELD-SHEET
SL SLIDE
SP SPRING
SP-SCREW SPECIAL-SCREW
SPACER, BAT SPACER, BATTERY
SPR SPRING
SPR-P P-SPRING
SPR-PC-PUSH P-SPRING, C-PUSH
T-SP T-SPRING
TERM TERMINAL
TRIG TRIGGER
TUN TUNING
VOL VOLUME
W WASHER
WHL WHEEL
WORM-WHL WORM-WHEEL
43
931196
2–11, IKENOHAT A 1–CHOME, TAITO-KU , TOKYO 110, JAPAN TEL:03 (3827) 3111
Printed in Singapore
Loading...