Air-Shields RW82-1, 1E, 1C User manual

HillRom

_ SERVICE MANUAL

RESUSCITAIRE.

Radiant Warmer

From Hili-Rom Air-Shields

Product: RW82-1, 1E and 1C

For Paris Or Technical Assistance		man221rd
USA [phone] Canada	(800)	267-2337
International: Contact your	disiributor.

i

|

LIMITED WARRANTY

The product being described in this manual is warranted against defects in materials or workmanship for one year from the date of shipment from Hill-Rom Air-Shields, Inc., Hatboro, with the following exceptions:

All consumable and disposable products are guaranteed to be free from defects upon shipment only. Calibrations are considered normal maintenance and are not included in the 1 year warranty.*

During the warranty period any defective parts other than those listed above will be replaced at no charge to the customer. There will be no labor charge for replacing the parts within the continental U.S.

This warranty is rendered void and Hili-Rom Air-Shieids, inc. cannot be held liable for conditions resultant therefrom if.

1.	Damage to the	unit	is incurred	as a result of mishandling.
2.	The customer faifs to maintain			the unit in a proper manner.
3.	The customer	uses	any paris,	accessories, or fittings not specified or sold by Hili-Rom Air-Shields,
	Inc.

4.

Sale or service is performed

by a non-certified

service/dealer

agency.

THE

FOREGOING

WARRANTIES

ARE EXCLUSIVE AND IN LIEU OF ALL OTHER

EXPRESS

WARRAN-

TIES

AND

IMPLIED

WARRANTIES,

INCLUDING BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES

OF

MERCHANTABILITY AND FITNESS OF PURPOSE. HILL-ROM AIR-SHIELDS’

OBLIGATION

UNDER

THESE

WARRANTIES

SHALL NOT INCLUDE ANY LIABILITY FOR LOSS OF

PROFITS,

DIRECT,

INDI-

RECTOR CONSEQUENTIAL DAMAGES OR DELAYS. Some states, provinces,

or countries do not allow the

exclusion or limitation of

incidental

or

consequential

damages,

so

the

above exclusion

or limitation

may

not

apply. Any improper or negligent use, any alterations or repairs not in accordance

with Hill-Rom Air-Shields'

manuats

or

performed by

others in such manner as in Hill-Rom Air-Shields’ sole

judgement affects

the

product

materially and

adversely,

shall void

these warranties.

These

warranties

do

not

cover

failures due

to

misuse,

-abuse, neglect,

or

lack of

routine maintenance.

No

employee

or

representative

of

Hill-Rom Air-Shields is au-

thorized

to

change

these

warranties

in any way

or

grant

any

other warranty

unless in

writing and signed by a

Hill-Rom officer. These warranties provide specific

legal

rights; but,

there

may be

other available rights;

which

vary from state to state,

province to

province,

or country

to

country.

*The Accreditation Manual for Hospitals requires each

piece

of equipment

to

be

tested

prior to initial use and at

feast

annually

thereafter.

To comply

with this standard, we recommend

that

you

participate

in our

Preventive

Maintenance Program during the warranty period. This service can

be

performed

by

certified

technicians

through

our

Product

Service Group

and authorized

dealers.

SERVICE

For

optimal

performance,

product service should be performed

only

by

qualified

service

personnel. Technical

Services

representatives

are located throughout the United States and

Canada

and are dispatched for re-

quired maintenance by calling USA

[phone]

and

Canada

(800)

267-2337.

Customers

outside

the

U.S.

and

Canada should

contact their local factory-authorized Hil-Rom

Air-Shields'

distributor

for service.

		Hill-Rom		Air-Shields,
		A HILLENBRAND	INDUSTRY
		330 Jacksonviile Road,		Hatboro,	PA 19040
	A
CAT. NO.	82 990	07-7			Printed	in USA		10/96
E123456789					Change		1	8/97
A123456789					Change		2	6/98
					Change		3	10/98
man221rd					Change		4	4/99
© 1999 by	Hill-Rom	Company, Inc. ALL	RIGHTS RESERVED.		h			288
					granges		6
					Change			12/99

oN

ζω

ニ

プ ー ュ

À y7

O

/

o4, 2

г

è 5 NO

ο QA

ki Ru RU A{ Né

LO

LON Rus

NU

Awe

Ne

©

©

U

O (O

:. ; 040)

€

(o>

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Resuscitaire® Radiant Warmer Service Manual Correction (man221rd) Since the release of the Resuscitaire® Radiant Warmer Service Manual (man221rd), minor

inaccuracies

have been

found that require updating. Listed

below are the page numbers and

corrections

that

require

updating.

Mark

these

in your

service

manual.

These

corrections will

be made

during

the next revision

of

the

service

manual. If

you

have any

questions,

contact

Hill-Rom Technical Support at [phone].

Page

Number

Correction

Required

Page

ii

In the section “Symbols,” add the warning labels

from

page

5 of this

document.

|

Page

2-1

In the section

“2.2 Assembly,”

add

the

following:

AWARNING:

*Cylinder heights may vary. When replacing a gas cylinder, ensure that the tank does not exceed the

maximum

tank

height

specification.

Also,

prior

to

placing the cylinder, confirm that there is sufficient

clearance

between

the

bottom

of the tank and the

floor

when

the

Resuscitaire

VHA

is

in

its

lowest

position.

After these checks have been completed,

raise

the

VHA

to

its

maximum

height

and

install/

remove

the cylinder.

Failure

to

do

so

could

result

in personal

injury

or

equipment

damage.

Page

2-2

Replace

Figure

2.1

with

the figure on page 6 of

this

document.

Page

3-3

Replace

Table

3.LA

with

pages

7

to

10

of

this

document.

Page

3-5

Replace

Table

3.1B

with

pages

11 to 14 of this document.

Page

3-12

Add page 15

of

this

document

regarding

the

Gas

Delivery

Module

and

Figure

3.9.

Page

3-18

Replace

the

section

“Reserve

Gas

Supply”

with

the

following;

ReserveGasSupply

On American units, the regulator

is

preset

at

65

psi

(448

kPa)

when

the cylinder

pressure

is

1200

psi (8274

kPa).

On

United

Kingdom

and

Canadian

units,

the

regulator

is

preset

at 45 psi

(310

kPa)

when

the

cylinder

pressure

is 1500 psi (10342 kPa).

The

output

varies

with

the

input

pressure.

© 2003 by Hill-Rom Services, Inc. ALL.RIGHTS RESERVED.

February 3, 2003

man221rd-e2

Page 1 of 60

Hill-ROMA ir-Shields,

A HILLENBRAND

INDUSTRY

Page

3-18

In

the

section

“Resuscitation

Module,”

replace

the caution with

the

following:

A

CAUTION:

If the

knob is

removed,

calibrate the unit (refer to

“5.12 Resuscitation Module Check and Calibration

Procedures”

on

page

5-44).

Failure to do so

could

result

in equipment

damage.

Page

4-1

In

the

section

“4.1 General,”

add

the

following:

AWARNING:

Cylinder heights may vary. When repiacing a gas

cylinder, ensure that the tank does					not	exceed		the
maximum		tank height	specification.		Also		confirm
that	there	is sufficient	clearance	between			the
bottom of		the tank and the floor		when		the
ResuscitaireVHA.is.in.its.lowest position-prior.to..|.....
placement.		After these checks have been
completed,		raise the VHA to its		maximum			height
and	instali/remove the		cylinder.	Failure		to	do	so

		could		result	in	personal	injury	or equipment
		damage.
Page 4-4	In the section	“Metal		Surfaces,”		add the	following:
	A	WARNING:
		The	heater		element may be hot enough to cause
		burns.		Before cleaning			the warmer head, allow 30
		minutes for			the unit to sufficiently cool. Failure to
		do	so	could	result in personal			injury.

Page 2 of 60

man221rd-e2

February 3, 2003

Hill-RomAir-Shields

A HILLENBRAND INDUSTRY

Page 4-5

In the section “4.5 Reassembly After Cleaning,” add the following:

АWARNING:

Cylinder heights may vary. When

replacing

a

gas

cylinder, ensure that the tank does not exceed the

maximum

tank

height specification.

Also,

prior to

placing the cylinder, confirm that

there

is

sufficient

clearance between the bottom of

the

tank

and

the

floor

when

the

Resuscitaire

VHA

is

in

its

lowest

position. After these checks have

been

completed,

raise

the

VHA

to

its

maximum

height

and

install/

remove the

cylinder.

Page

5-2

Replace

the section “5.2.2

Resuscitation

Calibration”

with page

16 of

this

document.

Page

5-2

Replace the section “5.3 DC

Power

Requirements”

with

page

17

of

|

this

document.

Page

5-30

In Table

5.1:

Troubleshooting

Guidelines

for

System

Error

Codes,”

replace

the row for Error

#21

with

page

18

of

this

document.

Page

5-36

In the section

“5.11.2

Removing

and

Replacing

the

Back

Cover,”

add

the

following:

:

АWARNING:

Cylinder heights may vary. When replacing a gas cylinder, ensure that the tank does not exceed the

maximum tank height specification. Also, prior to placing the cylinder, confirm that there is sufficient clearance between the bottom of the tank and the

floor when		the	Resuscitaire		VHA		is in	its lowest
position.	After		these	checks	have		been	completed,
raise the VHA to its				maximum		height		and	install/
remove	the	cylinder.		Failure	to	do	so	could	result
in personal		injury or		equipment		damage.

February 3, 2003

man22 ird-e2

Page 3 of 60

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Page 5-39	In the section	“5.11.6 Removing and Replacing the Gas Supply
	Module,” add	the following:

AWARNING:

Cylinder heights may vary. When replacing a gas cylinder, ensure that the tank does not exceed the maximum tank height specification. Also, prior to

placing the cylinder, confirm that there is sufficient

clearance

between

the

bottom

of

the

tank

and the

floor when

the

Resuscitaire

VHA

is

in

its

lowest

position. After these checks have been completed,

raise

the

VHA

to

its

maximum

height

and

install/

remove

the

cylinder.

Failure to do so could result

in personal

injury

or

equipment

damage.

Page

5-40

Replace

section

“5.11.7

Removing

and

Replacing the

Quartz

Heating

“JElement”

with

pages

19

through

24

of

this document.

Page

5-43

Add

sections

“5.11.9

Removing

and

Replacing the Heater Grill” and

“5.11.10 Removing and Replacing the

Warmer Head

Top Cover”

found on pages 25 through

29

of this

document.

Page

6-13G

Replace

Figure

6.1E

with

page

30

of this

document

Page

6-13L

Add

items 19

through

21

to

the

Label

List as

follows:

*Label,Caution,HiPressure,Eng................................. 8200300

+

Label,

Warning,

Max

Cylinder

HT

(<70

cm).................

8200315D

*

Label,

Warning,

Max

Cylinder

HT

(<76

cm).................

8200315E

Pages

6-20

through

Replace

with

page

31

through

page

36

of

this

document.

6-22

Pages

6-36

through

Replace

with

page

37

through

page

60

of

this

document.

6-50

Pages

7-8

and 7-9

Replace

with

foldouts

FO

7-8

and

FO

7-9

of

this

document.

Page 4 of 60

man22 1rd-e2

February 3, 2003

Hill-Rom Air-Shields,

A HILLENBRAND INDUSTRY

Warning Labels, Maximum Tank Height

m221de214

February 3, 2003

man221rd-e2

]

Page 5 of 60

Hill-Rom Air-Shields

A HILLENBRAND INDUSTRY

Figure 2.1: Installation

m221de213

Page 6 of 60

man221rd-e2

February 3, 2003

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Table 3.1A Specifications

POWER

REQUIREMENTS

120V

Models

(North America)

120V,

60 Hz,

750W

100V

Models

(Japan)

100V,

50/60

Hz,

750W

220/240V

Models

(IEC)

220/240V,

50/60

Hz,

750W

OVERLOAD

PROTECTION

120V

Models

(USA)

Dual

12A

Circuit

Breakers

100V

Models

(Japan)

Dual

12A

Circuit

Breakers

220/240V

Models

(TEC)

Dual

6A

Circuit Breakers

CHASSIS

LEAKAGE CURRENT

100V

and

120V

Models

300

LA

maximum

220V

and

240V

Models

500

LA

maximum

EXAMINATION

LIGHT

>100

Foot

Candles

(0.11

lumens/cm?)

ALARMS

High

Temperature

Activates

if

Skin

Temperature

Probe is attached and the skin

temperature

sensor

reaches

39.0°C.

Resets at 38.5°C.

Chk

Patient

Activates

in

Manual Mode after

10 mins.

Remains on with audi-

ble

alarm

every

30

s. for

5

mins.;

totalling

15

mins.

Then

heater

is

turned

Off.

Apgar

Timer

Activates

at

the

1-,

5-, and 10-

minute

Apgar Time

intervals.

Power

Fail

Activates when power is lost.

Probe

Activates

if

Skin

Temperature

Probe fails (open or short).

System

Fail

Indicates system failure; refer to

paragraph

5.10.

Baby

Temp

Activates

if Baby Temperature

fluctuates

1°C above or

below

set

point.

- February 3, 2003

man221rd-e2

Page 7 of 60

Hill-RomA ir-Shields

A HILLENBRAND INDUSTRY

Electrical Module Audio Alarms

Blender Module Pneumatic Audio Alarm

DISPLAYS

Skin Temperature Display Range

Skin Temperature Display Accuracy

Skin Temperature Display Resolution

Apgar Timer Display Range

Apgar Timer Display Accuracy

Apgar Timer Display Resolution

MANUAL HEAT CONTROL

DATA PORT

MATTRESS TILT

DEMENSIONS AND WEIGHT

Mattress Height

Height

Width (Side to Side)

Depth (Front to Back)

Weight

ENVIRONMENTAL

Operating Temperature Range

Storage Temperature Range

Relative Humidity Operating Range

RESUSCITATION (w/AutoBreath™ feature, PN 8140080; w/o AutoBreath™ feature, PN 8140072)

Wall Supply Pressure

Cylinder Pressure

Page 8 of 60

man221rd-e2 .

Tone Frequency: 1.2 KHz maxi- mum

Three-Stage sound level: 15 s low, 15 s medium, then high.

Vibrating reed

18	to	40°C		(64.4	to	104°F)
+0.2°C			for	31°C	to	37°C (88°F
to	98.6°F)
0.1°С (0.5°Е)
0:00		to	59:59 (mins:secs)
0+1s

is

Adjustable in 10% increments from zero to full power (100%).

2400 Bits/second fixed Baud Rate. RS232C compatible

0, 5, and 10 degrees

100 em (39.4")

188 cm (74")

72.4cm (28.5")

111.8cm (44") 91 kg (200 Ibs.)

18°C to 30°C (64.4°F to 86°F) ambient

- 20°C to + 45°C( - 4°F to + 113°F) ambient

5% RH to 95% RH, non-con- densing

40 psi (276 kPa) to 75 psi

(517 kPa)

3000 psi (20684 kPa) maximum

February 3, 2003

HillA-irRom-Shields

A HILLENBRAND

INDUSTRY

Cylinder

Length

(with VHA)

70

om

(27.5")

Cylinder

Length (with VHA and spacer) +

76

cm

(30")

Cylinder

Diameter

10

-

12

cm

(4 -

5")

maximum

Suction

Circuit

Adjustable Suction Inten-

0"H2O

(0

mm

Hg)

to

80"H,0

sity

(130

mm

Hg)

Patient Gas Supply Airway Pressure Limit,

0 to 50

cm

HyO

+

10%

(4.9kPa)

Operator

Adjustable

Patient Gas Supply Fixed Pressure Relief,

60

cm

HO

+ 10%

(5.9kPa)

Factory

Set

Primary

Outlet

Supply Pressure Limit

160.1

cm

HyO

(15.7

kPa)

+

20%

Primary

Outlet

Flow

Range

0 ipm to 15 jpm

Auxiliary Supply Pressure Limit (w/o

160.1

спа

Н2О

(15.7

kPa)

+

AutoBreath™

feature)

10%

maximum

Auxiliary Supply Pressure Limit (with

160.1

cm H,0 (15.7 kPa) +

AutoBreathTM

feature)

10%

maximum

Auxiliary Flow Circuit Flow Range

0 Ipm to 15 Ipm

Auxiliary Flow

Circuit Pressure

160.1

ста

Н2О

(15.7

КРа)

+

10%

maximum

AutoBreath™ feature (Factory Installed

Option)

VE Ratio

Fixed

at

1:2

+

20%

PEEP

Ratio

0

to

18

+

4

cm

H,0

(1.8

+ 0.4

kPa)

Breath

Rate

18

to

60

BPM

+ 10%

of

setting

Adjustable

Airway

Pressure Relief

0

to

50

+

5

cm

H,0

(4.9

+

0.5

kPa)

Fixed

Maximum

Pressure

60

cm

HO

+

10%

(5.9 kPa

+

10%)

Oxygen

Consumption

50

lpm maximum

RESUSCITATION

(w/AutoBreath™

feature, PN 8140081; w/o AutoBreath™

feature,

PN

8140073)

Wall Supply

Pressure

40

psi

(276 kPa) to 75 psi

(517

kPa)

Cylinder

Pressure

3000

psi

(20684 kPa)

maximum

February

3, 2003

man221rd-e2

Page

9

of 60

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Cylinder	Length	(with	VHA)	70	cm	(27.5")
Cylinder	Length	(with	VHA and spacer)	76	cm	(30")
Cylinder	Diameter			10	- 12	cm (4 - 5") maximum

Suction

Circuit

Adjustable Suction Inten-

0"H,0

(0

mm

Hg)

to

80"H,0

sity

(150

mm

Hg)

Patient Gas Supply Airway Pressure Limit,

O to

50

em

H,O

+

10% (4.9kPa)

Operator Adjustable

Patient Gas Supply Fixed Pressure Relief,

50

em

H,O

+ 20%

(5.0kPa)

Factory

Set

Primary

Outlet

Supply

Pressure Limit

160.1

cm

H,O

(15.7

kPa)

+

20%

Primary

Outlet

Flow

Range

0 Ipm to 15 lpm

Auxiliary Supply Pressure Limit (w/o

160.1

em

H,0

(15.7

kPa)

+

AutoBreath™

feature)

10%

maximum

Auxiliary Supply Pressure Limit (with

40

cm

HO

(4

kPa)

+

10%

max-

AutoBreathTM

feature)

imum

Auxiliary Flow Circuit Flow Range

0

Ipm

to

15

ipm

Auxiliary Flow

Circuit

Pressure

40

cm

H20

(4

kPa)

+

10%

max-

imum

AutoBreath™ feature (Factory Installed

Option)

I/E Ratio

Fixed

at

1:2 +

20%

PEEP

Ratio

0

to

18 +

4

em

H,0

(1.8

= 0.4

kPa)

Breath

Rate

18

to

60

BPM

+ 10%

of

setting

Adjustable

Airway

Pressure Relief

0

to

50+

5

cm

H,0

(4.9405

kPa)

Fixed

Maximum Pressure

50

cm

HO

+

10%

(5.0

kPa +

10%)

Oxygen

Consumption

50

lpm maximum

MONITOR

SHELF

DIMENSIONS

14.0" (35.6 em) x 12.0"

(30.5

em)

+Data Tag Reference 82VHA part numbers: 8201080 and 8201081

8201170 and 8201171

Page 10 of 60

man221rd-e2

February 3, 2003

Hill-RomA ir-Shields

AHILLENBRAND INDUSTRY

	Table 3.1B Specifications—CE-Mark Version
POWER	REQUIREMENTS	220/240V,		50/60	Hz, 750W
OVERLOAD PROTECTION		Dual	6A	Circuit Breakers
CHASSIS	LEAKAGE CURRENT	500	LA maximum
EXAMINATION LIGHT		>0.11 lumens/cm?			(100 Foot
		Candles)

ALARMS

High Temperature Activates if Skin Temperature Probe is attached and the skin temperature sensor reaches 39.0°C. Resets at 38.5°C.

Chk Patient

Activates

in Manual

Mode

after

10

mins.

Remains on with audi-

ble

alarm

every 30 s. for 5

mins.;

totalling

15

mins.

Then

heater

is

turned

Off.

Apgar

Timer

Activates

at the

1-, 5-, and

10-

minute

Apgar

Time

intervals.

Power

Fail

Activates

when

power

is

lost.

Probe

Activates

if Skin

Temperature

Probe fails (open or short).

System

Fail

Indicates

system

failure;

refer

to

paragraph

5.10.

Baby

Temp

Activates

if Baby

Temperature

fluctuates

1°C

above

or

below

set

point.

Electrical Module

Audio

Alarms

Tone

Frequency:

1.2

KHz

maxi-

mum

Three-Stage sound level:

15

s

low,

15

s

medium,

then

high.

Blender Module Pneumatic Audio Alarm

Vibrating

reed

DISPLAYS

Skin

Temperature

Display

Accuracy

40.220

for 31°C

to

37°C

(88°F

to

98.6°F)

Skin

Temperature

Display

Resolution

0.1°C

(0.5°F)

Apgar

Timer

Display

Range

0:00

to

59:59

(mins:secs)

Apgar

Timer

Display

Accuracy

0+0.5s

February 3, 2003

man221rd-e2

Page

11

of

60

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Apgar

Timer

Display

Resolution

18

MANUAL

HEAT

CONTROL

Adjustable

in

10%

increments

from zero to full power (100%).

DATA

PORT

2400

Bits/second

fixed Baud

Rate.

RS232C

compatible.

MATTRESS

TILT

0,

5,

and 10

degrees

DIMENSIONS

AND

WEIGHT

Mattress

Height

100

cm

(39.4")

Height

188

cm

(74")

Width

(Side

to Side)

72.4

cm

(28.5")

Depth

(Front

to

Back)

111.8

cm (44")

Weight

91

kg

(200

lbs.)

ENVIRONMENTAL

Operating

Temperature Range

18°C to 30°C (64.4°F to

86°F)

amb

ambient

Storage

Temperature

Range

~ 20°C

to +

45°C

(

- 4°F

to +

113°F)

ambient

Relative

Humidity

OPerating Range

5% RH to 95% RH, non-con-

densing

RESUSCITATION

(w/AutoBreath™

feature, PN 8140080; w/o AutoBreath™

feature,

PN

8140072)

Wall Supply

Pressure

276

kPa (40

psi)

to

517 kPa (75

psi)

Cylinder

Pressure

20684

kPa

(3000

psi) maximum

Cylinder

Length

(with VHA)

70

cm

(27.5")

Cylinder Length (with VHA and spacer) +

76

cm

(30")

Cylinder

Diameter

10

-

12

cm

(4

- 5")

maximum

Suction

Circuit

Adjustable Suction

Inten-

0

mm

Hg (0"H,0)

to150

mm

sity

Hg

(80"H,0)

Patient Gas Supply Airway Pressure Limit,

4.9kPa

(0 to 50

cm

H)0)

+ 10%

Operator

Adjustable

Patient

Gas

Supply

Fixed Pressure

Relief,

5.9kPa

(60

cm

H20) + 10%

Factory Set

Primary Outlet Supply Pressure Limit

15.7 kPa (160.1 cm HO) £

20%

Page 12 of 60

man221rd-e2

February 3, 2003

Hill-RomAir-Shields

A HILLENBRAND INDUSTRY

Primary Outlet Flow Range

Auxiliary Supply Pressure Limit (w/o AutoBreath™ feature)

Auxiliary Supply Pressure Limit (with AutoBreath™ feature)

Auxiliary Flow Circuit Flow Range Auxiliary Flow Circuit Pressure

AutoBreath™ feature (Factory Installed Option)

VE Ratio PEEP Ratio

0 lpm	to	15 lpm
| 15.7	kPa	(160.1	cm	HO)	+
10%	maximum
15.7	kPa (160.1 cm H,0) +
10%	maximum
0 Ipm to 15 Ipm
15.7	kPa	(160.1	cm	HO)	=

10% maximum

Fixed at 1:2 + 20%

1.8 + 0.4 kPa (0 to 18 + 4 cm H,0)

Breath Rate	18	to	60	BPM	+	10%	of	setting
Adjustable Airway Pressure Relief	0	to	49	+ 0.5	kPa	(0	to	S0 +5
	cm	H,0)

Fixed Maximum Pressure

5.9 kPa + 10% (60 cm H,0 £

10%)

Oxygen	Consumption		50	lpm	maximum
RESUSCITATION (w/AutoBreath™
feature, PN 8140081; w/o AutoBreath™
feature,	PN	8140073)
Wall Supply		Pressure	276	kPa (40 psi)				to	517 kPa
			(75	psi)
Cylinder	Pressure		20684		kPa	(3000		psi) maximum
Cylinder	Length (with VHA)		70	cm	(27.5")
Cylinder	Length (with VHA and spacer)		76	cm	(30")
Cylinder	Diameter		10	- 12	cm	(4 -	5")		maximum
Suction	Circuit Adjustable Suction Inten-		0 mm		Hg	(0"H2O)			to150	mm
sity			Hg	(80"H2O)
Patient Gas Supply Airway Pressure Limit,			4.9kPa		(0	to 50	cm		H,O)	+ 10%
Operator	Adjustable
Patient Gas Supply Fixed Pressure Relief,			5.0kPa		(50	cm	H,0) + 20%
Factory	Set

Primary Outlet Supply Pressure Limit

15.7	kPa (160.1 cm HO) +
20%

February 3, 2003

man221rd-e2

Page 13 of 60

Hill-RomA

ir-Shields

A HILLENBRAND INDUSTRY

Primary Outlet

Flow

Range

0 lpm to 15 lpm

Auxiliary Supply Pressure Limit (w/o

15.7

kPa

(160.1

cm

H,0)

+

AutoBreath™

feature)

10%

maximum

Auxiliary Supply Pressure Limit (with

4 kPa

(40

cm

H,0)

+ 10%

max-

AutoBreath™

feature)

imum

Auxiliary Flow Circuit Flow Range

0 Ipm

to

15 lpm

Auxiliary Flow

Circuit Pressure

4 kPa (40 cm H,O) + 10% max-

imum

AutoBreath™ feature (Factory Installed

Option)

VE Ratio

Fixed

at

1:2 +

20%

PEEP

Ratio

0 to 1.+ 80.4

kPa(0

to

18

+4

em

H,0)

Breath

Rate

18

to

60

BPM

+

10% of

setting

Adjustable Airway Pressure Relief

4.9+0.5

kPa

(0

to

5045

cm

H2O)

Fixed

Maximum

Pressure

5.0

kPa

+

10%

(50

cm H30 +

10%)

Oxygen Consumption

50

lpm

maximum

MONITOR

SHELF

DIMENSIONS

35.6 cm (14.0") x 30.5 cm

(12.0")

+ Data Tag Reference 82VHA part numbers: 8201080 and 8201081

8201170 and 8201171

Page 14 of 60

man221rd-e2

February 3, 2003

Hill-RomAir-Shields.

A HILLENBRAND INDUSTRY

Gas Delivery Module

When the blender module is included in the system, the gas delivery module provides 0 lpm to 15 Ipm of oxygen/air mixture, as selected by the user (see

	figure	3.9 on	page 10). When	no	blender module		is included	in the	system, the
	gas delivery		module provides	O Ipm to 15 Ipm of			oxygen, as	selected by the
	user. The flow control is a calibrated,					dial-type, flow adjustment.
	Figure	3.9:	Gas Delivery Module Theory of Operation
Gas	supply		Blender	Resuscitation			Breathing
module			module		module		circuit
Oxygen					Oxygen
pipeline					pipeline		Manual
Oxygen					Oxygen
pipeline			|		pipeline		Manual/
and	reserve				and	reserve	automatic
			Precision
	.		blender			.
Oxygen/air				|_|	Oxygen/air		Manual		with
pipeline					pipeline		integral
								pop off
Oxygen/air
pipeline
and	reserve
									m221de107

February 3,2003

©

man221rd-e2

Page 15 of 60

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

5.2.2 Resuscitation Calibration

Refer	to “5.12 Resuscitation Module Check and Calibration Procedures”. on
page	5-44.

Page 16 of 60

man221rd-e2

February 3, 2003

Hill-RomAir-Shields

A HILLENBRAND INDUSTRY

5.3DC Power Requirements

Tools	required:			Calibrated		digital voltmeter (Fluke®! 8080A or					equivalent)
At the	specified		AC	input	voltage,		verify	the following	DC	voltages	at the
power	and control			P.C. board		(see	table 5.1 on page 5-2).
				Table	5.1:	DC	Power	Requirements
DC	Output		Voltage					Connector	and	Pin
+5.1V	+	0.05V			J2-2 or J2-3
+12V	+	0.5V			J2-1
-12V		0.5V			J2-6
Ground					J2-4

1. Fluke® is a registered trademark of Fluke Corporation.

February 3, 2003

man22 1rd-e2

Page 17 of 60

HillA-irRom-Shields

A HILLENBRAND INDUSTRY

Error	Number		Explanation
Error	#21	Ambient	temperature	probe	#1/
		Ambient	temperature	probe

error, > 0.4°C

.

Possible Corrective Action

Check for a faulty skin temperature probe. Ensure that the skin temperature probe is not in contact with materials.

Adjust the skin temperature probe sen- sor (refer to “5.2.1 Adjustments” on page 5-1).

Replace PCB1.

Page 18 of 60

man221rd-e2

February 3, 2003