Page 1
SERVICE/OPERATION
MANUAL
Spray & Stripe
Spray & Stripe
Spray & Stripe
Spray & Stripe
001-778 AUG07
Page 2
Table of Contents
INTRODUCTION
Spray & Stripe Specications 1
Safety Warnings 2-6
GETTING STARTED
Flushing 7
Daily Maintenance 8
Pressure Relief Procedure 9
Setting Up to Stripe or Spray 10
Starting Up 11-12
Striping Operation 13
REPAIRS/MAINTENANCE
INSTRUCTIONS
Spray Gun Operation 14
Spray Gun Troubleshooting 15
Field Troubleshooting 16
Servicing the Fluid Pump 17
Servicing the Piston Rod 18
Servicing the Suction Assembly 18
Packing Replacement 19-20
Elect. Control Board Replacement 21
Pressure Calibration of Board 21
Clutch Replacement 22
Cltuch Troubleshooting 23
PRODUCT DIAGRAMS & PARTS LISTS
Gearbox Assembly 24
Spray Gun Assembly 25
Gun Mount Assembly 25
Frame Assembly 26
Swivel Wheel Assembly 27
Suction Assembly 27
Striping Tip Guide 28
ACCESSORIES 29-30
Manufactured by: AIRLESSCO BY DUROTECH CO.
5397 Commerce Ave.,Moorpark, CA 93021
Tel: 805-523-0211 Fax: 805-523-1063
www.airlessco.com eMail: techservice@airlessco.com
SUBJECT TO CHANGE WITHOUT NOTICE.
Copyright © 2007, Airlessco by Durotech Co. All rights reserved.
Page 3
Introduction
INTRODUCTION
The heart of the Spray & Stripe series is the time
tested and contractor proven Airlessco “LP” piston
paint pump. Designed for professional airless
line striping and paint spraying, it is used daily by
thousands of painting professionals worldwide–
with a reputation for trouble free performance
that’s unmatched in the industry.
They’re small, compact, easy to use, and quick to
clean. Even changing colors is a breeze. Stripe
with water-based paints made for trafc lines or
athletic elds. A professional quality spray gun is
mounted on a multi-position spray arm. Great
balance and light weight make this striper ideal
for a one-man operation.
A tool-less quick release of the spray gun from
its mount lets you spray paint using stencils, or
utilize the 50' of supplied hose and the spray gun
to paint with exterior latex & enamel paints.
The Airlessco exclusive turnbuckle based
RADIUS MEMORY™ system for striping smooth
curves and circles every time.
Flexibility to handle a wide variety of applications
make the Spray & Stripe popular with cities,
school districts, and sports programs for parking
lot or athletic eld striping, and for use as a
mobile airless spraying station. It’s perfect for
painting fences, buildings, & covering grafti.
SPECIFICATIONS:
Part # 305-385 Airlessco Spray & Stripe 3600
305-380 ALLPRO Spray & Stripe
Max Pressure 3000 PSI (170 Bar)
Max Output 0.7 GPM (2.65 Litres/min.)
Pressure Control Electronic pressure controls operate electric clutch
Max Tip 1 gun @ 0.025”
Engine Durotech DE400 w/ automatic low oil level shutdown
Service Level Up to 5000 gallons per year
IMPORTANT WARNING !!
HANDLE THIS UNIT AS YOU WOULD A LOADED FIREARM!!
High pressure spray can cause extremely serious injury.
OBSERVE ALL WARNINGS!
Before operating this unit, read and follow all safety warnings and
instructions related to the usage of this equipment. READ, LEARN,
and FOLLOW the Pressure Relief Procedure on Page 10 and
understand all warnings on pages 2 thru 6.
All Service Procedures to be performed by an Authorized Airlessco Service Center ONLY.
NO MODIFICATIONS or alterations of any Airlessco Equipment or part is allowed.
1
Page 4
Safety Warnings
TOXIC FLUID HAZARD
Hazardous uid or toxic fumes can cause serious injury or death if splashed in eyes or on skin, inhaled or swallowed. Know
the hazards of the uid you are using. Store & dispose of hazardous uids according to manufacturer, local, state & national
guidelines. ALWAYS wear protective eye wear, gloves, clothing and respirator as recommended by uid manufacturer.
ALWAYS INSPECT SPRAYING AREA
• ALWAYS keep spraying area free from obstructions.
• ALWAYS make sure area has good ventilation to safely remove vapors and mists.
• NEVER keep ammable material in spraying area.
• NEVER spray in vicinity of open ame or other sources of ignition.
SPRAY GUN SAFETY
• ALWAYS set safety lock on the gun in "LOCKED" position when not in use and before servicing or cleaning.
• NEVER remove or modify any part of the gun.
• ALWAYS REMOVE SPRAY TIP when cleaning. Flush unit with LOWEST POSSIBLE PRESSURE.
• ALWAYS check operation of all gun safety devices before each use.
• Be very careful when removing the spray tip or hose from gun. A plugged line contains uid under pressure. If the tip or
line is plugged, follow the PRESSURE RELIEF PROCEDURE as outlined on page 10.
TIP GUARD
ALWAYS have the tip guard in place on the spray gun while spraying. The tip guard alerts you to the injection hazard and helps
prevent accidentally placing your ngers or any part of your body close to the spray tip.
SPRAY TIP SAFETY
Use extreme caution when cleaning or changing spray tips. If the spray tip clogs while spraying, engage the gun safety latch
immediately.
• ALWAYS follow the PRESSURE RELIEF PROCEDURE and then remove the spray tip to clean it.
• NEVER wipe off build up around the spray tip.
• ALWAYS remove tip & tip guard to clean AFTER pump is turned off and the pressure is relieved by following the
PRESSURE RELIEF PROCEDURE.
KEEP CLEAR OF MOVING PARTS
Keep clear of moving parts when starting or operating the sprayer. Do not put your ngers into any openings to avoid
amputation by moving parts or burns from hot parts.
Precaution is the best insurance against an accident.
When starting the engine, maintain a safe distance from moving parts of the equipment.
Before adjusting or servicing any mechanical part of the sprayer, follow the PRESSURE RELIEF PROCEDURE, and remove
the ignition cable from the spark plug to prevent accidental starting of the sprayer.
LABELING
Keep all labels on the unit clean and readable. Replacement labels are available from the manufacturer.
2
Page 5
Safety Warnings
HIGH PRESSURE SPRAY CAN CAUSE EXTREMELY SERIOUS INJURY.
OBSERVE ALL WARNINGS.
INJECTION HAZARD
Fluids under high pressure from spray or leaks can penetrate the skin and cause extremely serious
injury, including the need for amputation.
• NEVER point the spray gun at anyone or any part of the body.
• NEVER put hands or ngers over the spray tip. Do not use a rag or any other material over your ngers. Paint will
penetrate through material and into the hand.
• NEVER try to stop or deect leaks with your hand or body.
• NEVER try to "blow back" paint, this is not an air spray sprayer.
• ALWAYS have gun tip guard in place when spraying.
• ALWAYS lock gun trigger when you stop spraying.
• ALWAYS remove tip from the gun to clean it.
• ALWAYS follow the PRESSURE RELIEF PROCEDURE, as shown on page 10, before cleaning or removing the
spray tip or servicing any system equipment.
• ALWAYS Be sure equipment safety devices are operating properly before each use.
• ALWAYS tighten all uid connections before each use.
MEDICAL TREATMENT
If any uid appears to penetrate your skin, get EMERGENCY CARE AT ONCE. DO NOT TREAT AS A SIMPLE CUT.
* Go to an emergency room immediately.
* Tell the doctor you suspect an injection injury.
* Tell him what kind of material you were spraying with and have him read NOTE TO PHYSICIAN.
MEDICAL ALERT - Airless Spray Wounds NOTE TO PHYSICIAN:
If any uid appears to penetrate your skin, get Injection in the skin is a traumatic injury.
EMERGENCY MEDICAL CARE AT ONCE. DO It is important to treat the injury surgically
NOT TREAT AS A SIMPLE CUT. Tell the doctor as soon as possible. DO NOT DELAY treatment
exactly what uid was injected. Have him read to research toxicity. Toxicity is a concern with
the following "NOTE TO PHYSICIAN". some exotic coatings injected directly into the
bloodstream. Consultation with a plastic surgeon or
reconstructive hand surgeon may be advisable.
GENERAL PRECAUTIONS
• NEVER alter equipment in any manner. • NEVER smoke while in spraying area.
• NEVER spray highly ammable materials. • NEVER use around children.
• NEVER allow another person to use sprayer unless they are thoroughly instructed on safety use and
given this operators manual to read.
• ALWAYS wear a spray mask, gloves and protective eye wear while spraying.
• ALWAYS ensure re extinquishing equipment is readily available and properly maintained.
NEVER LEAVE SPRAYER UNATTENDED WITH PRESSURE IN THE SYSTEM.
FOLLOW PRESSURE RELIEF PROCEDURES ON PAGE 10.
3
Page 6
Safety Warnings
GROUNDING
Ground the sprayer and other components in the system to reduce the risk of static sparking, re or
explosion which can result in serious bodily injury and property damage.
Always ground all of these components:
• Fluid Hose: use only grounded hoses.
• Spray gun or dispensing valve: grounding is obtained through connection to a properly
grounded uid hose and pump.
• Object being sprayed: according to your local code.
• All solvent pails used when ushing should only be metal pails which are conductive.
Once each week, check electrical resistance of hose (when using multiple hose assemblies, check
overall resistance of un-pressurized hose must not exceed 29 megohms (max) for any coupled length
or combination of hose lengths. If hose exceeds these limits, replace it immediately.
Never exceed 300 Ft. (150 m.) overall combined hose length to assure electrical continuity.
AVOID COMPONENT RUPTURE
This sprayer operates at 2500 psi (170 bar). Always be sure that all components and accessories have a
maximum working pressure of at least 3000 psi to avoid rupture which can result in serious bodily injury
including injection and property damage.
• NEVER leave a pressurized sprayer unattended to avoid accidental operation of it which could result in serious
bodily injury.
• ALWAYS follow the PRESSURE RELIEF PROCEDURE whenever you stop spraying and before adjusting,
removing or repairing any part of the sprayer.
• NEVER alter or modify any part of the equipment to avoid possible component rupture which could result in
serious bodily injury and property damage.
• NEVER use weak, damaged or non-conductive paint hoses. Do not allow kinking or crushing of hoses or allow
it to vibrate against rough, sharp or hot surfaces. Before each use, check hoses for damage and wear and ensure
all uid connections are secure.
• REPLACE any damaged hose. NEVER use tape or any device to mend the hose.
• NEVER attempt to stop any leakage in the line or ttings with your hand or any part of the body. Turn off the
unit and release pressure by following PRESSURE RELIEF PROCEDURE on page 10.
• ALWAYS use approved high pressure ttings and replacement parts.
• ALWAYS ensure re extinquishing equipment is readily available and properly maintained.
Do not use halogenated solvents in this system. The prime valve, 2 gun manifold and most
airless guns have aluminum parts and may explode. Cleaning agents, coatings, paints or
adhesives may contain halogenated hydrocarbon solvents. DON'T TAKE CHANCES!
Consult your material suppliers to be sure. Some of the most common of these solvents are:
Carbontetrachloride, Chlorobenzene, Dichloroethane, Dichloroethyl Ether, Ethylbromide,
Ethylchloride, Tethrachloethane. Alternate valves and guns are available
if you need to use these solvents.
4
Page 7
Safety Warnings
FLUSHING
Reduce risk of injection injury, static sparking or splashing by following the specic cleaning procedure on page 7.
• ALWAYS follow the PRESSURE RELIEF PROCEDURE on page 10.
• ALWAYS remove the spray tip before ushing. Hold a metal part of the gun rmly to the side of a metal pail and
use the lowest possible uid pressure during ushing.
• NEVER use cleaning solvents with ash points below 140º F. Some of these are: acetone, benzene, ether,
gasoline and naphtha. Consult your supplier to be sure.
• NEVER smoke in the spraying/cleaning area.
PREVENT STATIC SPARKING FIRE/ EXPLOSIONS
ALWAYS be sure all equipment and objects being sprayed are properly grounded. Always ground sprayer, paint
bucket and object being sprayed. See "grounding" on page 4 for detailed grounding information.
Vapors created when spraying can be ignited by sparks. To reduce the risk of re, do not plug in or unplug any
electrical cords in an enclosed spray area,. This can create sparks when there is any chance of igniting vapors still
in the air. Follow the coating & solvent manufacturers safety warnings and precautions.
Use only conductive uid hoses for airless applications. Be sure gun is grounded through hose connections. Check
ground continuity in hose & equipment. Overall (end to end) resistance of un-pressurized hose must not exceed 29
megohms for any coupled length or combination of hose length. Use only high pressure airless hoses with static
wire approved for 3000 psi.
Important: United States Government safety standards have been adopted under the Occupational
Safety & Health Act. These standards, particularly the General Standards, Part 1910, & the
Construction Standards, part 1926 should be consulted.
WHEN SPRAYING & CLEANING WITH FLAMMABLE PAINTS OR PAINT THINNERS:
1. When spraying with ammable liquids, unit must be located a minimum of 25 feet away from spraying area
in a well ventilated area. Ventilation must be sufcient enough to prevent the accumulation of vapors.
2. To eliminate electrostatic discharge, ground the spray unit, paint bucket and spraying object. Use only high
pressure airless hoses approved for 3000 psi which is conductive.
3. Remove spray tip before cleaning gun and hose. Make contact of gun with bucket and spray without the tip in
a well ventilated area, into the grounded steel bucket.
4. Never use high pressure in the cleaning process. USE MINIMUM PRESSURE.
5. Do not smoke in spraying/cleaning area.
GAS ENGINE PRECAUTIONS
WHEN ADDING FUEL
• Turn engine OFF and let engine cool at least 2
minutes before removing gas cap.
• Fill fuel tank outdoors or in well ventilated area.
• Do not overll fuel tank. Fill tank to
approximately1 inches below top of neck to
allow for fuel expansion.
• Keep gasoline away from sparks, open ames,
pilot lights, heat and other ignition sources.
• Check fuel lines, tank, cap and ttings frequently
for cracks or leaks. Replace if necessary.
Fire or explosion can cause severe burns or death.
WHEN STARTING ENGINE
• Make sure spark plug, mufer, fuel cap and air cleaner
are in place.
• Do not crank engine with spark plug removed.
• If fuel spills, wait until it evaporates before starting
engine.
• If engine oods, set choke to OPEN/RUN
position, place throttle in FAST and crank until
engine starts.
Gasoline & its vapors are extremely
ammable & explosive.
WHEN OPERATING EQUIPMENT
• Do not tip engine or equipment at angle which
causes gasoline to spill.
5
Page 8
Safety Warnings
WHEN TRANSPORTING EQUIPMENT
• Transport with fuel tank EMPTY or with fuel shut-off
valve OFF.
WHEN STORING GASOLINE OR EQUIPMENT WITH
FUEL IN TANK
• Store away from furnaces, stoves, water heaters and
other appliances that have pilot lights or other ignition
source. They can ignite gasoline vapors.
Starting engine creates sparking.
Sparking can ignite nearby ammable gases.
Explosion and re could result.
• If there is natural or LP gas leakage in area, do not
start engine.
• Do not use pressurized starting uids because vapors
are ammable.
Rapid retraction of starter cord (kickback) will pull
hand and arm toward engine faster than you can let go.
Broken bones, fractures, bruises or sprains could result.
• When starting engine, pull cord slowly until resistance is
felt, then pull rapidly.
• Remove all external equipment/engine loads before starting
engine.
• Direct coupled equipment components such as, but not
limited to, blades, impellors, pulleys, sprockets, etc. must
be securely attached.
Rotating parts can contact or entangle hands, feet,
hair, clothing or accessories.
Traumatic amputation or severe laceration can result.
• Operate equipment with guards in place.
• Keep hands and feet away from rotating parts.
• Tie up long hair and remove jewelry.
• Do not wear loose tting clothing, dangling drawstrings or
items that could become caught.
Running engines produce heat. Engine parts,
especially mufers, become extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush,
etc. can catch re.
• Allow mufer, engine cylinder and ns to cool before
touching.
• Remove accumulated combustibles from mufer area and
cylinder area.
• Install and maintain in working order a spark arrester
before using equipment on forest covered, grass covered
and brush covered unimproved land. The state of
California requires this (Section 4442 of the California
Public Resources Code). Other states may have similar
laws. Federal laws apply on federal land.
Unintentional sparking can result in re
or electric shock.
Unintentional start up can result in entanglement,
traumatic amputation, or lacerations.
BEFORE PERFORMING ADJUSTMENTS OR
REPAIRS
• Disconnect spark plug wire and keep it away from
spark plug.
• Disconnect battery at negative terminal (only
engines with electric start).
WHEN TESTING FOR SPARK
• Use approved spark plug tester.
• Do not check for spark with spark plug removal.
Engines give off carbon monoxide, an odorless,
colorless, poison gas.
Breathing carbon monoxide can cause nausea,
fainting or death.
• Start and run engine outdoors.
• Do not start or run engine in enclosed area, even if doors or
windows are open.
6
Page 9
Flushing
Read prior to using your sprayer
1. New Sprayer
Your Airlessco unit was factory tested in an antifreeze solution which was left in the pump.
Before using oil-base paint, ush with mineral spirits only. Before using water-base paint
ush with soapy water, then do a clean water ush.
2. Changing Colors
Flush with a compatible solvent such as mineral spirits or water.
3. Changing from Water-Base to Oil-Base Paint
Flush with soapy water, then mineral spirits.
4. Changing from Oil-Base to Water-Base Paint
Flush with mineral spirits, followed by soapy water, then do a clean water ush.
5. Storage
Oil-base paint: Flush with mineral spirits.
Water-base paint: Flush with water, then mineral spirits and leave the pump, hose and gun
lled with mineral spirits. For longer storage, use mixture of mineral spirits and motor oil
(half & half). Shut off the sprayer, follow Pressure Relief Procedure on page 10
7
Page 10
Daily Maintenance
1. Keep the displacement pump packing nut/wet cup lubricated with Airlessco TSO
(Throat Seal Oil) at all times. The TSO helps protect the rod and the packings.
Airlessco Throat Seal Oil
6 ounce bottle Part # 188-187
1 quart bottle Part # 188-392
2. Inspect the packing nut daily. Your pump has Airlessco’s patented Triple Life Packing System.
Packing life will be extended a minimum of three times if the
following "Packing Adjustment" procedure is followed:
If seepage of paint into the packing nut and/or movement of the piston upward is found (while not
spraying), the packing nut should be tightened enough to stop leakage only, but not any tighter.
Overtightening will damage the packings and reduce the packing life.
8
3. Check suction nut daily.
8
Page 11
Pressure Relief Procedure
IMPORTANT!
To avoid possible serious body injury, always follow this procedure whenever the
sprayer is shut off, when checking it, when installing, changing or cleaning tips,
whenever you stop spraying, or when you are instructed to relieve the pressure.
1. Engage the gun safety latch. Refer to the
separate instruction manual provided with
your gun on its safety features and how to
engage safety latch.
2. Turn the unit off.
3. Disengage the gun safety latch and trigger
the gun to relieve residual uid pressure.
Hold metal part of the gun in
contact with grounded metal pail.
USE MINIMUM PRESSURE !
If the SPRAY TIP OR HOSE IS CLOGGED, follow Step 1 through 5 above. Expect paint
splashing into the bucket while relieving pressure during Step 4.
If you suspect that pressure hasn't been relieved due to damaged Prime/Pressure
Relief Valve or other reason, engage the gun safety latch and take your unit to an
authorized Airlessco Service Center.
4. Turn Prime/Pressure Relief Valve (PR Valve)
to the open (priming) position to relieve
residual uid pressure.
There will be a wider gap between valve
handle and cam body when in open
position. In the closed position there is
only a very slight gap.
.
Note: The valve handle can move both
clockwise and counter clockwise and can
face different directions.
5. Re-engage gun safety latch and
close Prime/Pressure Relief Valve.
9
Page 12
Setting Up to Stripe or Spray
1. Connect the hose and gun.
a. If the hose is not already installed on the striper,
remove the plastic cap plug from the outlet tee
at the spray pump, and screw a conductive or grounded
3000 psi airless spray hose onto uid outlet.
b. Connect an airless spray gun to the other end of
the hose.
c. Do not use steel braided airless hose. Use nylon
braided airless hose only.
NOTE:
Use thread seal on tapered male threads only.
Do not use thread sealer on swivel
unions as they are made to self-seal.
2. Remove the snap-on cover plate
over the piston.
3. Grounding
WARNING
To reduce the risk of static sparking, re or
explosion which can result in serious bodily
injury and property damage, always ground
the sprayer and system components and the
object being sprayed, as instructed in the
safety warning section of this manual.
A small steel chain grounding strap is installed at
the factory to prevent static build-up.
4. Flush the sprayer
As per "Flushing Procedure" in this manual.
3. Fill the packing nut/wet cup with 5 drops
of Airlessco Throat Seal Oil (TSO) and
then reinstall snap-on piston cover plate
Failure to lubricate the piston properly
with throat seal oil can cause premature
wear and damage to piston and packings.
10
Page 13
Starting Up
1. Learn the Functions
of the Controls.
PRIME/PRESSURE (PR) RELIEF VALVE is used to
prime pump and to relieve pressure from gun, hose and tip.
Prime/Pressure Relief Valve (Prime/PR Valve)
Used to relieve pressure from gun, hose & tip and to prime
the unit when in OPEN position. (It is in open position
when there is a wider gap
between valve handle and
cam body)
When in CLOSED position,
there is only a very slight gap
between handle & body.
When closed the system is
pressurized. Handle as a loaded rearm!
PRESSURE CONTROL KNOB is used to adjust
pressure. Turn clockwise (CW) to increase pressure
and counterclockwise (CCW) to
decrease pressure.
2. Prepare the Material
a. Prepare the material according to the material
manufacturer's recommendations.
b. Place the suction tube into the material
container.
4. Adjusting the Pressure
a. Turn the Pressure Control Knob Clockwise to
increase pressure and counterclockwise to decrease
pressure.
b. Always use the lowest pressure necessary to
completely atomize the material.
Note: Operating the sprayer at higher pressure
than needed, wastes material, causes early tip
wear, and shortens sprayer life.
c. If more coverage is needed, use a larger tip rather
than increasing the pressure.
d. Check the spray pattern. The tip size and angle
determines the pattern width and ow rate.
Follow the "Pressure Relief Procedure".
To reduce the risk of injection, never hold
your hand, body, ngers or hand in a rag
in front of the spray tip when cleaning
or checking for a cleared tip. Always
point the gun toward the ground or into a
waste container when checking to see if
the tip is cleared or when using a
self-cleaning tip.
3. Starting the Sprayer
a. Prime/PR Valve must be "OPEN" in the priming
position.
b. When you have ensured that the gun safety latch
is engaged, attach tip and safety guard.
c. Turn the engine ON/OFF switch to the "ON"
position. Pull rope vigorously until engine
starts.
d. Turn Pressure Control Knob clockwise to prime
the pump.
e. After the pump is primed, turn Prime/PR Valve to
the "Closed" position.
f. Turn Pressure Control Knob to the desired spray
pressure.
g. Disengage the gun safety latch and you are
ready to spray.
When you spray into the paint bucket,
always use the lowest spray pressure
and maintain rm metal to metal contact
between gun and container.
To stop the unit in an emergency, turn the
engine off. Then relieve the uid pressure
in the pump and hose as instructed in the
Pressure Relief Procedure.
11
Page 14
Starting Up
5. When Shutting off the Sprayer
a. Whenever you stop spraying, even for a short break,
follow the "Pressure Relief Procedure".
b. Clean the tip & gun as recommended in the seperate
Gun Manual supplied with the gun/
c. Flush the sprayer at the end of each work day, if the
material you are spraying is water-based, or if it could
harden in the sprayer overnight. See "Flushing". Use a
compatible solvent to ush, then ll the pump and hoses
with an oil based solvent such as mineral spirits.
d. For long term shutdown or storage, refer to the
"Flushing" section of this manual.
Be sure to relieve pressure in
the pump after lling with Airlessco
Pump Conditioner.
Avoiding Tip Clogs
There is an easy way to keep the outside of the
tip clean from material build up:
Every time you stop spraying, for even a minute,
lock the gun and submerge it into a small bucket
of thinner suitable for the material sprayed.
Thinner will dissolve the buildup of paint on the
outside of tip, tip guard and gun much more
effectively if the paint doesn't have time to dry
out completely.
12
Page 15
Striping Operation
1. Choose handle location
The choices are, installing the handle opposite of the
single wheel assembly (standard set up) or placing
the handle directly over the single wheel assembly.
The handle location is really a matter of personal
preference, however having the handle away from
the single wheel assembly allows for easier loading/
unloading from a van or truck.
2. Cable Tension Adjustment
Once the handle and gun arm assemblies are set up to
the preferred positions, pressurize the unit and trigger
each gun to ensure that they activate and release
correctly. If not, adjust the cable tension as follows:
a. Locate the adjustment knobs on the base of the
gun trigger, where the cable connects to the gun
trigger assembly.
b. Loose the locking nut & move the adjusting screw
until the slack has been removed from the cable.
c. Tighten locking nut and retest gun triggers for
proper function.
4. Setting the Swivel Wheel with RADIUS MEMORY
™
Refer to gure below
a. Pull back on the swivel wheel trigger to adjust the
wheel to desired angle.
b. T
o set the angle for constant arch loosen the jam
nuts on the
Turnbuckle. Place Turnbuckle onto
the mounting nub located on the striper frame.
Adjust the turnbuckle until it ts over the mounting
nub located on the wheel frame. Tighten jam nuts
on the turnbuckle to afx the length.
Note: If you have archs that you paint regularly, purchase
additional
Turnbuckles (P.N. 136-163) and keep them set to
those arc sizes for easy use.
Note: There is an additional cable adjustment
where the cable attaches to the gun holder
assembly. Use only if the gun trigger adjustment
is insufcient.
3. Miscellaneous Operations
CURBS: To paint at a 90 degree angle to spray the
sides of curbs install a part # 032-028 swivel between
gun head and tip guard and aim guard sideways
towards the curb.
WIDE STRIPES: Install wider fan striping tips and
raise the gun height to achieve the desired width line.
STENCILS: Install standard spray tip on the outer
gun. Rotate gun to remove from the gun holder and
use the gun to spray within your stencils. Use of an
extension pole will make this job a lot easier on the
operators back and is highly reccomended.
STANDARD PAINTING: Install the appropriate
size and type of paint spraying tip (standard paint
spray, “W” wide pattern, or “Fine Finish”). Remove
gun and spray just as you do for stencils. Additional
paint hose may be required depending on the
distance between the job and the equipment.
Wheel Release
Turnbuckle
Mounting Nubs
13
Page 16
Spray Gun Operation
SPRAY GUN
Attach spray gun to airless unit and tighten ttings securely.
Set the gun safety latch. (Also may be called gun safety
lock, or trigger lock)
* The gun safety latch should always be set when the gun is
not being triggered.
Read all warnings and safety precautions supplied with the
spray gun and in product manual.
MAJOR COMPONENTS OF SPRAY GUN &
REVERSIBLE REV-TIP
Reversible
Spray Tip
Tip Guard
Trigger Guard
Press up here & pull gently
to remove trigger guard
™
Gun Safety
Latch or Lock
Gun Handle. Unscrew
from gun head to service
lter inside.
SPRAY TIP ASSEMBLY
1. Be sure the pressure relief procedure is followed
before assembling tip and housing to the gun.
2. Insert REV-TIP™ cylinder into the REV-GUARD
(guard housing assembly).
3. Guide the metal seat into REV-GUARD™ (guard
housing assembly) through the retaining nut & turn
until it seats against the cylinder.
4. Insert the O-Ring gasket onto the metal seat so that it
ts into the grooves.
5. Finger tighten REV-GUARD™ retaining nut onto the gun.
6. Turn guard in the desired position.
7. Completely tighten the retaining nut.
Retaining Nut
REV-GUARD™
Guard Housing Assembly
G Thread 7/8" 561-002
F Thread 11/16" 561-001
REV-TIP™ Cylinder
Part # 561-XXX
O-Ring Gasket
Metal Seat
Part # 561-029
Part # 561-026
™
TO REMOVE CLOGS FROM SPRAY TIP
1. Lock gun safety latch.
2. Turn REV-TIP™ handle 180 degrees.
3. Disengage trigger lock and trigger gun into
the pail.
4. If the REV-TIP™ handle appears locked
(resists turning), loosen the retaining nut. The
handle will now turn easily.
5. Engage gun safety latch and return handle to
the spray position.
Retaining Nut
Reverse to
Unplug
Spray Position Shown
14
CLEANING SPRAY GUN
Immediately after the work is nished, ush the gun out
with a solvent. Brush pins with solvent and oil them
lightly so they will not collect dried paint.
CLEANING FILTER IN GUN HANDLE
To clean the lter, use a brush dipped in an
appropriate solvent. Change or clean lters
at least once a day. Some types of latex may
require a lter change after four hours of
operation
.
Page 17
Spray Gun Troubleshooting
DEFECTS
Coarse spray Low pressure Increase the pressure
Excessive fogging High pressure Reduce pressure for satisfactory pattern
(overspray) Material too thin Use less thinner
Pattern too wide Spray angle too large Use smaller spray angle tip
Pattern too narrow Spray angle too small Use larger spray angle tip. (If coverage is OK,
try tip in same nozzle group)
Too much material Tip size too large Use next smaller tip
Material too thin
Pressure too high Reduce pressure
Too little material Tip size too small Use next larger tip
Material too thick
Thin distribution in Worn tip Change for new tip
center of pattern Wrong tip Use tip with a smaller spray angle
"horns"
CAUSE CORRECTION
Thick skin on work Material too viscous Thin material
Application too heavy Reduce pressure and/or use smaller tip
Coating fails to Material too viscous Thin material
close & smooth over
Spray pattern irregular, Orice clogged Clean carefully
deected Tip damaged Replace with new tip
Craters or pock marks Solvent balance Use 1-3% "short" solvents remainder "long"
solvents. (This is most likely to happen with
material of low viscosity, lacquers etc.)
Bubbles on work Contamination or dust Clean surface to be sprayed
Clogged screens Extraneous material Clean screen
in paint.
Coarse pigments Use coarse screen if orice size allows
Poorly milled pigments Use coarser screen, larger orice tips. Obain ball
(paint pigments glocculate milled paint. If thinner was added, test to see if a
cover screen. Incompatible
drop on top of
paint mixes or attens out on
paint mixture & thinners. on the surface. If not, try different thinner
in fresh batch of paint.
TEST THE PATTERN
15
Page 18
Field Troubleshooting
PROBLEM CAUSE SOLUTION
Unit doesn't prime Airleak due to:
• Loose Suction Nut • Tighten Suction Nut
• Worn O-Rings • Replace O-Ring (106-011) on
suction seat, & O-Ring (106-
020) below suction seat
• Hole in Suction Hose • Replace Suction Hose (331-290)
Stuck or Fouled Balls Service outlet valve suction
assembly
Unit primes but has no Pressure set too low Turn up pressure
or poor pressure
Filter(s) are clogged Clean or replace gun lter, inlet
lter and/or manifold lter
Outlet Valve fouled/worn Service outlet valve
Prime/Pressure Relief valve Clean or replace prime valve
bypassing
Packings and/or piston worn • Tighten packing nut
• Repack unit
Unit does not maintain Blown spray tip Replace spray tip
good spraying pressure
Packings and/or piston worn Repack unit
Upper Seat worn Replace upper seat
16
Page 19
Servicing the Fluid Pump
Fluid Pump Disconnect
Refer to Figure 1
1. Follow the Pressure Relief Procedure on page 10.
2. Flush the material you are spraying out of the machine.
3. Remove the connecting rod shield (331-111).
4. Move the piston rod (331-093) to its lowest position
by cycling pump slowly.
5. Remove the retaining ring (331-062) from the
connecting rod (331-038) and slide the sleeve (331-
117) down revealing the connecting rod pin (331-065).
6. Remove the suction tube assembly from the uid
pump (331-209) by unscrewing the suction nut
(331-034) with the packing adjustment tool.
7. Using a 1/2” wrench unscrew the two bolts (100-318)
from the cover assembly (331-234). The uid pump
(331-209) will be hanging loosely at this point.
8. Remove the connecting rod pin (331-065) out of
the connecting rod (331-038), allowing the removal
of the uid pump (331-209) from the machine.
Fluid Pump Reinstall
Refer to Figure 1 & 4
1. Loosen the packing nut and ensure that the piston rod
(331-093) is in its upper position in the uid pump body
(331-011). Slip the sleeve (331-117) & the retaining
ring (331-062) over the piston rod.
2. Push the piston rod up into the connecting rod (331-
038) & align the holes. Insert the connecting rod pin
(331-065) through the connecting rod & piston. Slip
the sleeve up over the connecting rod pin and insert
the retaining ring into the groove on the connecting rod.
3. Push the two bolts (100-318) through the tube spacers
(331-074) & screw them into the cover assembly (331-
234). Using a 1/2” wrench, tighten the two bolts evenly
(alternating between them) until you reach 20 ft-lbs.
4. Reassemble lower suction valve assembly by placing
the suction seat (331-409), O-ring (106-011), suction
ball (331-030) & suction ball guide (331-029) in the
suction nut (331-034) & screw onto uid pump body.
331-209
FIGURE 1
5. Start the machine and operate slowly to check the piston
rod for binding. Adjust the two bolts, holding the uid
pump body to the cover assembly, if necessary. This
will eliminate any binding.
6. Tighten the packing nut clockwise until resistance is
felt against the Belleville Springs, then go 3/4 of a turn
more. Put ve drops of Airlessco Throat Seal Oil into the
packing nut.
7. Run the machine at full pressure for several minutes.
Release the pressure by following the Pressure Relief
Procedure & readjust the packing nut per step 6 above.
8. Install the connecting rod shield (331-111) so that the
small hole is in the upper right hand corner.
17
Page 20
Servicing the Piston Rod - Outlet Valve
DISASSEMBLY OF THE OUTLET VALVE
REFER TO FIGURE 3
1. Disconnect the Fluid Pump following instructions on page 17 .
2. Place piston holder (331-195) in a vise. Slide piston into
the holder & lock in place with a 3/8” dowel (331-196).
3. Use a 1/4” allen wrench to unscrew the outlet seat retainer
(331-026) from the piston.
4. Remove the outlet seat (331-026), O-ring (331-100) and
outlet ball (331-027).
5. Inspect outlet ball & seat for wear. Replace as necessary.
6. While piston is still locked in the holder, install parts
back into the piston in the following order:
ball, outlet seat and O-ring
Before reinstalling the outlet seat support, apply two drops of
Loctite No. 242 (blue) on the threads & torque to 20 ft-lbs.
NOTE: Airlessco LP pump tool kit 188-197 is suggested for this task.
Kit includes: Packing Tightening Bar (189-211), Packing Removal Tool (331-153),
Piston Holder (331-195), 3/8” dowel (331-196).
331-196
FIGURE 3
Piston
331-195
Servicing the Suction Assembly
REFER TO FIGURE 4
1. Un-thread and remove suction nut from the uid pump body.
2. Remove suction seat (331-409), O-ring (106-011), suction ball
(331-030) and suction retainer (331-029).
3. Clean all parts and inspect them for wear or damage, replacing
parts as needed.
4. Clean inside of the uid pump body.
5. Reassemble lower suction valve assembly by placing the
suction seat (331-409), O-ring (106-011), suction ball (331-030)
& suction ball guide (331-029) in the suction nut (331-034) &
FIGURE 4
18
Page 21
Packing Replacement Procedures
Replacement Instructions:
Fluid Pump Removal - Refer to Figure 1
1. Follow the Pressure Relief Procedure on page 9.
2. Flush material you are spraying out of the machine.
3. Remove the connecting rod shield (331-111).
4. Move the piston rod (331-093) to its lowest position by
cycling pump slowly.
5. Remove the retaining ring (331-062) from the connecting
rod (331-038) and slide the sleeve (331-117) down
revealing the connecting rod pin (331-065).
6. Remove the suction tube assembly from the uid pump
(331-209) by unscrewing the suction nut (331-034) with the
packing adjustment tool.
7. Using a 1/2” wrench unscrew the two bolts (100-318) from
the cover assembly (331-234). The uid pump (331-209)
will be hanging loosely at this point.
8. Remove the connecting rod pin (331-065) out of the
connecting rod (331-038), allowing the removal of the uid
pump (331-209) from the machine.
Disassembly of the Fluid Pump - Figure 6
1. Unscrew & remove the packing nut (331-037).
2. Push the piston rod (331-708) down through the packings
& out of the pump.
3. Now push the packing removal tool (331-465) up through
the pump & remove from the top bringing packings, spacer
& springs along with it, leaving uid body (331-011) empty.
*Make sure all old packings & glands have been removed from uid pump.
4. Clean inside of uid body (331-011).
5. Disassemble all parts & clean for reassembly. Discard any
old packings.
6. Lubricate leather packing in lightweight oil for 10 minutes
prior to reassembly.
Disassembly of the Outlet Valve - Figure 3
1. Place piston holder (331-195) in a vise. Slide piston into the
holder & lock in place with a 3/8” dowel.
2. Use a 1/4” allen wrench to unscrew the outlet seat retainer
(331-026) from the piston.
3.
outlet ball (331-027).
4. Inspect outlet ball & seat for wear. Replace as necessary.
5. While piston is still locked in the holder, install parts back into
the piston in the following order:
ball, outlet seat and O-ring
Before reinstalling the outlet seat support, apply two drops of
Loctite No. 242 (blue) on the threads & torque to 20 ft-lbs.
Remove the outlet seat (331-026), O-ring (331-100) and
REASSEMBLY - Figure 5 & 6
1. Take lower male gland (331-014) & place it down on
the at side.
2. Take three of the lower polyethylene packings (331-016) & two
of the leather packings (331-306) & place onto the male gland in
the following order with the inverted side down :
Polyethylene, leather, polyethylene, leather, polyethylene.
3. Take the female adaptor (331-305), which is inverted on both
sides , & place it on top of your assembled lower packings.
4. Follow step 2 above with your packings inverted side up.
5. Take the second lower male gland and place it on top of your
assembled packings with the rounded side down.
6. Take assembled glands & packings (13 pieces) & slide on to the
lower half of the piston.
7. Take the spacer (331-018) & slide over the top of the piston (it
doesn’t matter which direction it sits), falling onto lower packings.
8. Take three Belleville Springs (331-025) & slide over the top of
the piston in the following order:
* First spring, curve facing down
* Second spring, curve facing up
* Third spring, curve facing down
9. Take the upper male gland (331-022) & place it rounded side up.
10. Take three upper polyethylene packings (331-023) & two leather
packings (331-307) & assemble with inverted side down ,
on to the male gland in the following order:
polyethylene, leather, polyethylene, leather, polyethylene.
11. Take upper female gland (331-021) & place on top of the assembled
upper packings with the inverted side down.
12. Take assembled upper glands & packings (7 pieces) & slide on
over the top of the piston, making sure inverted sides are down.
13. Take the packing holder (331-019) & replace the white O-ring
(106-009) & the black O-ring (106-010) with new ones from the
packing kit.
14. Slide the packing holder over the top of the upper packings
so they t inside.
15. Lubricate inside of the uid pump body & the outside of the
packings with a light weight oil.
16. Slide completed assembly into uid pump body (331-011).
* To keep packings secured in correct position, hold the pump body
upside down & push the completed assembly upwards into the pump
body. Once placed inside, tilt pump body back up to keep all pieces in.
17. Tighten packing nut (331-037) onto the top of the uid pump
body & tighten until you feel slight resistance against the
Belleville Springs (331-025). Using the Packing Adjustment Tool
(189-211), tighten another 3/4 of a turn.
Fluid Pump Reinstallation - Figure 1 & 4
1. Loosen packing nut & ensure that the piston rod (331-093) is in
its upper position in the uid pump body (331-011). Slip the
sleeve (331-117) & the retaining ring (331-062) over the piston rod.
2. Push piston rod up into the connecting rod (331-038) & align the
holes. Insert the connecting rod pin (331-065) through the
connecting rod & piston. Slip the sleeve up over the connecting
rod pin & insert retaining ring into the groove on the connecting rod.
(
(
(
19
Page 22
Packing Replacement Procedures
3. Push the two bolts (100-318) through the tube spacers
(331-074) & screw into the cover assembly (331-234).
Using a 1/2” wrench, tighten the two bolts evenly
(alternating between them) until you reach 20 ft-lbs.
4. Reassemble lower suction valve assembly by placing
the suction seat (331-409) O-ring (106-011), suction
ball (331-030) and suction ball guide (331-029) in the
suction nut (331-034) & screw onto the uid pump body.
5. Start the machine & operate slowly to check the piston
rod for binding. Adjust the bolts, holding the uid
pump body to the cover assembly, if necessary. This
will eliminate any binding.
76 Tighten packing nut clockwise until resistance is felt
against the Belleville Springs, then go 3/4 of a turn
more. Put ve drops of Airlessco Throat Seal Oil
into the packing nut.
7. Run the machine at full pressure for several minutes.
Release the pressure by following the Pressure Relief
Procedure & readjust the packing nut per step 6 above.
8. Install the connecting rod safety shield
(Fig. 1 Part # 331-111) so that the small hole is in the
upper right hand corner.
FIGURE 5
FIGURE 6
20
Page 23
Electrical Control Board Replacement
1. Remove electrical cover.
2. Disconnect sensor lead from Electrical Board.
3. Disconnect two clutch leads on Electrical Board
from leads on clutch.
4. Using a 1/16" allen, loosen set screw in Pressure
Control Knob and remove knob.
5. Using a 1/2" nutdriver or 1/2" deep socket, remove
nut from pressure control shaft. This will allow
removal of electrical control board from frame.
6. Replace Electrical Board Assembly in reverse order.
Adjust pressure as per procedure below, "Pressure
Calibration on the Electrical Control Board".
Pressure Calibration on the Electrical Control Board
1. Turn "Pressure Calibration" Trimpot adjustment on
electrical control board in the counter clockwise
direction at least 15 revolutions.
2. Connect 5000 psi glycerine pressure guage on output
of pump between uid pump & airless hose to
monitor Fluid Pump Pressure.
3. Turn Prime/Pressure Relief Valve to the open
(Prime) position. Start engine and run at maximum
RPM. Turn Pressure Control Knob to maximum
position (fully clockwise).
4. Using an insulated screwdriver, adjust "Pressure
Calibration" Trimpot by turning clockwise until the
clutch engages. When the clutch engages the pump
will commence Priming. When pump is primed, turn
the Prime/Pressure Relief Valve to the Closed (Pres
sure) Position
The pump will begin to pressurize and the clutch will disengage at a low pressure. Continue turning the Trimpot
clockwise to increase pressure to 3000 psi.
5. Trigger gun. The pressure should drop approximately
350-400 psi (when using a 3/8" hose), the clutch will
engage and build pressure to 3000 psi and disengage.
Trigger gun several times to ensure proper pressure
setting.
6. Turn Pressure Control Knob to minimum position. The
clutch should disengage and pump stop moving.
7. Secure leads with tie strap.
8. Replace cover on unit. Ensure the leads are not
pinched or damaged in the process of replacing covers.
21
Page 24
Clutch Replacement
REMOVE CLUTCH AS FOLLOWS:
1. Remove clutch and electrical box cover.
2. Disconnect the power lead coming from the engine
to the electrical box and feed it through the back of
the electrical box.
3. Using a 1/2” wrench along with a 1/2” socket
remove the four bolts attaching the engine to the
frame.
4. Remove the engine from the frame and set it on
your work bench so the clutch face is facing you.
INSTALL NEW CLUTCH AS FOLLOWS:
5. Using a small Phillips head screwdriver remove
the three screws holding the clutch face to the
clutch mount.
6. Disconnect two clutch leads from electrical board
leads. Carefully cut the small Zip-tie holding the
clutch wires to the gear housing.
7. Using a #2 Phillips screwdriver, remove the two
Phillips head screws holding the clutch eld to the
gear housing.
8. Pull the clutch eld off of the pinion gear.
1. Apply Anti-seize lubricant to the pinion shaft
coming out of the gearbox.
2. Slide new clutch eld over pinion shaft lining up
holes for the Phillips head screws located at the top
(indicated by a square tab) and bottom of the eld.
3. Feed the black clutch wires into electrical box &
plug into matching wires from the control board.
4. Install the new zip-tie (comes with the clutch
replacement kit) to the wire mount, keeping the
wires from the path of the clutch.
5. Apply blue Lock-tite to the screws and reinstall into
the gearbox.
6. Mount the clutch face to the clutch mount. Use
a Phillips head screwdriver to tighten the three
screws used for mounting the clutch face. Once
the screws come to a positive stop, hold them in
place with the screwdriver and thread the lock nuts
onto the portion of the screws protruding from the
rear of the clutch mount. Tighten the lock nuts until
they are ush with the clutch mount.
7. Set the engine back on the frame and tighten the
nuts and bolts so that you still can move the engie
back and forth fairly easily.
8. Using a feeler gauge slide the motor forward until
you reach a spacing of .010” between the clutch face
and the eld. Once you reach this point, nish
tightening the engine bolts, alternating to keep the
air gap the same on all sides of the clutch. Replace
the clutch cover.
22
Page 25
Troubleshooting - Clutch Does Not Engage
STEP 1: Ensure that the pressure control knob (POT) is in the maximum (CW) position.
STEP 2: Remove the clutch and electrical box covers.
STEP 3: Check all electrical connections between the engine magneto, sensor, control board and
clutch for loose connections or damaged leads.
STEP 4: Disconnect the two leads from the control board (blue) and the clutch assembly (black).
Using a multimeter, with the engine at maximum RPM, pressure control knob in the maximum
position and the prime valve open (priming) position, test the DC voltage across the boards leads
(blue). This voltage must be 13-14 VDC. If the readings are correct, the board, sensor and magneto
are okay and the problem is the clutch assembly. If this is the case, proceed to Step 5. If the voltage is
outside this range go to Step 7.
STEP 5: Check the spacing between the clutch eld and plate. The gap should be .010” to .014”. If
the gap is greater than .014” the gap is too wide. If this gap is too wide, replace the clutch assembly.
STEP 6: When the DC voltage from the board is not 13-14 VDC, disconnect the control board lead
(black) from the engine magneto lead (pink), located on the side of the engine. With the engine at
maximum RPM (3600), pressure control knob in maximum (CW) position and prime valve open
(priming), read the AC voltage from the magneto lead to the sprayer frame. This reading should be
19-24 VAC. If outside this range, contact your local Honda repair facility for magneto replacement. If
the magneto is producing the proper AC voltage, continue to Step 7.
STEP 7: Test the sensor by reading the resistance between the red and black wires. The resistance
runs between 1.5-3K ohms. A defective sensor usually shows no resistance (open). If the reading is
outside standards, replace the sensor. An alternative method to test the sensor, is to plug a new sensor
into the board and see if the clutch will engage. Caution! When using this method, ensure prime/
pressure valve is in the prime position. This is important because the sensor plugged into the board is
not measuring pressure in the uid section.
STEP 8: When Steps 6 & 7 have been completed and the magneto and sensor check good, the
electrical control board is the only item left, replace the board.
23
Page 26
Gear Box Assembly - Part No. 305-196
Part Number Description
100-028 Pipe Plug
100-226 45 degree Elbow
100-318 HXHD Screw
100-380 Screw
100-381 Screw
100-398 Retaining Ring
112-068 Ball Bearing
115-019 Hose Connector
117-008 Ball Bearing
305-199 Shaft Pinion
305-287 Machined End Bell
331-038 Crosshead Ass’y
331-046 Ball Bearing
Part Number Description
331-047 Ball Bearing
331-061 Sleeve Bearing
331-062 Retaining Ring
331-074 Spacer
331-103 Flat Washer
331-111 Front Shield
331-117 Sleeve
331-197 FLPHHD Screw
331-209 Pait Pump Ass’y
331-407 Crank Ass’y
331-537 Machined Cover
* Not Shown
331-132 Grease
24
Page 27
Spray Gun Assembly - Part No. 305-280
Part Number Description
100-011 Airless 1/4” x 50’ Hose
116-103 Cable Retainer Spring
120-115 008 Silver Gun w/o Tip
305-275 Gun Mount Ass’y
305-280 Spray Gun Assembly
561-025 Rev-Tip Male Seal
561-026 Rev- Tip Seal
116-103
563-317ST Striping Tip
560-517 Painting Tip (not installed)
-
Gun Mount Assembly - Part No. 305-275
Part Number Description
100-342 .321 x 1.25 LG. Screw
116-100 Compression Spring
119-049
119-050 Screw Pan HD
119-052 Hex Lock Nut
136-217 Jam Nut .250 nylon locking
140-045 Jam Nut .250
143-027 Ball Guide
305-077 Cable Ass’y
305-079 Wire Swivel Ass’y
305-089 Cable Sleeve
305-141 Cable Adjustor
305-142 Lever Ass’y
305-159 Sleeve Bearing
305-161 Spacer
305-272 Gun Mount Tube
305-273 Spacer .250
305-274 Trigger Lever
305-276 Spring Clip
331-103 Flat Washer 1/4
HexScrew .25-20UNC-2A x 1.88
LG.
136-217
25
Page 28
Frame Assembly
QTY
26
301-533 Paint Bucket Lid
Page 29
Swivel Wheel Assembly
-
Suction Assembly Part No. 331-290
Part Number Description Qty.
106-020
141-015 Hose Clamp
331-034 Suction Nut 1
331-035 Suction Elbow 1
331-217 Suction Filter 1
PTFE O-Ring 1
(some models only) 1
27
Page 30
Striping Tip Guide
TM
for Striping
Rev-Tip
Fan Width (6” from surface)
1-2 25-51
2-4 51-102
6-8 152-203
Striping Paint
Water Flow Rate (gpm)
(lpm)
Paint Flow Rate (gpm)
(lpm)
Pump Minimum (gpm)
Output
*Pump will support tip worn to next larger size.
in (mm)
102-152
4-6
(water @ 2000psi, 138 bar)
(latex paint @ 2000psi,
138 bar/1.36 spec. gr.)
*
(lpm)
STRIPING TIP - ORIFICE SIZE
(
.009 .011 .013 .015 .017 .019 .021 .023 .025 .027 .031 .035
113ST 115ST 117ST 119ST
215ST 217ST 219ST 221ST
315ST 317ST 319ST 321ST
Oil Base Oil Base Latex Latex Latex Latex LatexLatex
.12 .18 .24 .31 .38 .47 .57 .67 .77 1.03 1.31 1.63 1.80
.49 .69 .91 1.17 1.47 1.79 2.15 2.54 2.96 3.90 4.98 6.17 6.81
.10 .15 .21 .27 .33 .40 .49 .58 .66 .88 1.12 1.39 1.54
.38 .57 .79 1.02 1.25 1.51 1.85 2.20 2.50 3.33 4.24 5.26 5.83
.25 .25 .33 .40 .50 .60 .75 .88 1.0 1.25 1.5 2.0 2.2
1.0 1.0 1.25 1.5 1.9 2.3 2.8 3.3 3.8 4.7 5.7 7.5
Inches
)
8.2
REV-TIP
P.N. 562-xxxST
Includes Rev-Tip
& O-Ring Seal
Sample:
560-215
REV-TIP
TM
M
T
for Striping
TM
, Metal Seal
.
1/2 Fan Width
Orifice Size
REV-GUARD
Super Compact
P.N. 561-001
11/16-16 “F” Thread. Fits:
Airlessco, and some ASM,
Wagner, and Campbell Hausfeld.
P.N. 561-002
7/8-14 “G” Thread.
Fits some: Graco, Wagner,
Titan, Airlessco.
TM
Striping Tips should not be used for regular spraying. Striping tips are designed for a single pass
application, while spray tips are designed for the 1/3 overlap technique used for spray painting.
Spray Tip Replacement: During use high pressure will cause the orifice to grow larger. This destroys the flat
spray pattern or will leave tailing or two heavy lines on the outside of the pattern. When this ocurs replace the
spray tip or excessive paint will be wasted.
STRIPING TIPREGULAR PAINTING SPRAY TIP
28
LIGHT
LIGHTHEAVY
UNIFORM PATTERN
Page 31
PUMP CONDITIONER
Should be used on piston pumps
between uses to prevent paint from
drying on the piston & causing
packing wear.
010-001 Display of 48 - 1 oz. bottles
010-009 1 quart bottle
010-019 1 Gallon bottle
Case order quantity: 12 on quarts, 4 on gallons
Spray protectant for your machine
to to prevent paint from sticking to it.
STAY CLEAN
20 oz. can
114-030
™
Prefilter your paint using strainer
bags. One dozen per pack.
4 mil orange poly protects your
airless hose from paint and
abrasion damage. Comes in 1000'
roll with perforations each 50'.
100-426 Case of 6 Rolls
PAINT STRAINERS
100-064 Used to cover suction filter
100-065 5 Gallon strainer
HOSE COVER
100-219 Hose Cover Roll
THROAT SEAL OIL
Used in the wet cup of a piston pump
to prevent paint from drying on the
piston & causing damage to the upper
packing. Use with all piston pumps.
188-187 6 oz. Bottle
188-392 1 qt. Bottle
XTEND-A-POLE SYSTEM
Tip Extensions - Complete with
Patented SPRAY CLEAN REV-GUARD
Swivel Extension
Standard Tip Extension
HIGH PRESSURE HOSE
Strong yet flexible, suitable for
airless equipment up to 3300 PSI
Part No:
100-012 3/16” Whip Hose, 4 Ft.
100-011 1/4” Hose, 50 Ft.
100-023 3/8” Hose, 50 Ft.
100-037 1/2” Hose, 50 Ft.
100-010 1/4" Hose Connector
100-009 3/8" Hose Connector
TIP EXTENSIONS, “G” THREAD
032-170 6” Long
032-171 12” Long
032-172 18” Long
032-173 24” Long
Swivel Extension
Bare Pole
ACCESSORIES
SPRAY TIP ADAPTER
SWIVEL EXTENSION, “G” THREAD
032-184 36” Long
AIRLESSCO
032-012 "F to G" gun adapter to attach
®
Graco
tips to Airlessco 007 Spray Guns.
Flat Tip Washers
120-008 Flat Tip Washer
120-090 Flat Tip Washers 25 Pack
GUN FILTERS
120-090CX Coarse
120-090FX Fine
120-088 Filter Spring
EXTENSIONS (BARE POLES)
Add Tip Extension or Swivel Extension
to create desired length
032-053 24” Long
032-054 36” Long
032-035 7/8" - 14 Swivel
SWIVEL “G” THREAD
ADAPTERS
90° Pole to Gun Adapter
032-042
Gun Nut “F” Thread 11/16-16
032-010
Gun Nut “G” Thread
032-011
29
Page 32
Reversible
REV-TIP
Part # 560-xxx REV-TIP for Spray Painting
562-xxxST REV-TIP for Striping
POSI-LOC™ SYSTEM
Snap in centering of tip.
No leaks, splashback or mess.
SEAL LOCATING HANDLE
Tip handle simplifies installing
& aligning the seal.
EASIEST ASSEMBLY
Fewer parts - Less complicated
takes only seconds!
INTERCHANGEABLE
Can be used with most tip guards.
HIGHEST QUALITY CARBIDE
Micro-ground for extra long life,
consistent tip size & pattern.
STRINGER HOLE
Hang tip from hole for cleaning
SINGLE-SEAL
Metal seal - no leaks - sprays all coatings.
PRODUCT FEATURE
Aerodynamic Non Drip Guard
Finger Tight Nut
Requires Hand Tight Nut
Snap Tight Tip Lock
Low Profile Guard
Seal Orientation Slot
Tip Handle Hole for Stringer
No Seal Blow-By When Tip
is Not in Centered Position (1)
Seal Orientation Tool
on Tip Handle
Non Pin Diffuser (2)
Hardened Cylinder
Long Life Metal Seal
Short Fluid Path (3)
Tips Fit Graco Bases
Seal Installer on Tip
7/8 & 11/16 Gun Thread
AIRLESSCO
REV-TIP
n
n
n
n
n
n
n
n
n
n
n
n
n
n
n
™
Each tip individually tested!
Easy to install & align!
A
n
n
n
n
n
n
COMPETITOR
B
n
n
n
n
n
n
n
COMPETITOR
™
COMPETITOR
C
n
n
n
n
NEW!
Quick F l u s h
Quick F l u s h
Cuts Cleaning Time
& Saves Paint
Part # 170-005
Part # 170-005
!
Simple to Use...Fast to Finish!
EASY AS 1-2-3
1. Connect adapter to any “F”
or “G” thread airless gun & to a
garden hose as shown in picture.
2. Lock trigger open with the
supplied washer.
3. Turn on water ow to backush paint into the original
bucket for reuse while cleaning gun, hose, and pump.
The industry’s only “clean water” ushing system!
Spray Gun & Hose
Spray Pack
Working Pressure Rating
(1) Uncontrolled Spray Back Toward User (2) No Pattern Distortion From Pin
Copyright © 2004 Airlessco by Durotech Co. All rights reserved. Product specifications subject to change witout notice.
(3) No Spitting
5000 PSI
4050 PSI
5000 PSI
™
REV-GUARD
■ Airfoil shape for a clean,
no-drip application
■ Finger-tight nut, no tools
required
■ More compact size to use
Order #
561-002 REV-GUARD
with 7/8-14 (G) Thread with 11/16-16 (F) Thread
™
with 561-001 REV-GUARD™
in tight areas
Working
Pressure
Unknown
Part No: 002-015 Spray Pack includes:
120-554 008 Silver 4-Finger Gun
100-011 50’ x 1/4” Hi-Flex Airless Hose
30
Loading...