Air-King RSL Installation Manual

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

RSL Series

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN

THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY

AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always

be followed to reduce the risk of fire, electric shock and injury to

person, including the following:

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE
FOLLOWING:

a) Use this unit only in the manner intended by the manufacturer.If you have questions,

contact the manufacturer.

b) Before servicing or cleaning the unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK AND INJURY TO PERSON, OBSERVE THE
FOLLOWING:

a) Installation work and electrical wiring must be done by qualified person(s) in accordance

with all applicable codes and standards, including fire-related construction.

b) When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

c) This unit must be grounded.

d) Read all instructions before installing or using shell.

Range Hood

WARNING: TO REDUCE THE RISK OF A RANGE TOP GREASE

FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

b) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO PERSONS

IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE
FOLLOWING:

a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off

burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

d) Use an extinguisher ONLY if:

I. You know you have a Class ABC extinguisher, and you already know how to operate it.
II. The fire is small and contained in the area where it started.
III. The fire department is being called.
IV. You can fight the fire with your back to an exit.

INSTALLATION INSTRUCTIONS

CAUTION:

SERVICE PANEL BEFORE STARTING INSTALLATION.

MAKE SURE POWER IS SWITCHED OFF AT

SECTION 1

Preparing the Shell

1. Unpack shell from the carton and confirm that all pieces are present. In addition to the
shell you should have:

2 - #8 x 3/8 AB Screws

4 - #8 Mounting Screws

1 - Wire Compartment Cover and Screw

1 - Instruction/Safety Sheet

NOTE: Some shells may be shipped with a protective plastic adhered to the shell. It is
recommended to leave this in place during installation to protect the shell from scratching.
Remove when the installation is complete.

2. Lay the shell flat on a table so the underside is facing you. Use a piece of cardboard to
avoid damaging the table or the shell.

3. Remove lamp cover by squeezing the two tabs together (Figure 1):

Tabs

Figure 1

4. Install a 60 watt maximum type A19 bulb and reinstall the lamp cover.

SAVE THESE INSTRUCTIONS

6728041 Rev. B 2-16 1 of 2

www.airkinglimited.com

SECTION 2

Prepare the location for Shell Support

1. If the shell will be installed under cabinets that have a recessed bottom, it will be necessary
to install wood mounting strips (not included) so the shell will mount properly (Figure 2).

Wood Strip

SECTION 4

Wiring

CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE

IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL
ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL
WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.

1. Connect the White wire from the shell to the White wire from the supply, and the loose

Black wire from the shell to the Black wire of the supply. Connect the ground wire (green or
bare) from the supply to the green ground screw of the shell. Use approved methods for all
connections (Figure 5).

Figure 2

2. The thickness of the strips should be the same as the recess of the cabinet and they
should be approximately 2" wide.

3. Install the strips using appropriate length wood screws (not included). Make sure the
strips line up to the keyhole slots of the shell.

SECTION 3

Installing the Shell

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE STARTING INSTALLATION.

1. Hold the shell up to the installation location and mark the locations of the ducting (if
applicable), electrical, and mounting holes or mark the locations by measurement.

2. Cut appropriate holes for ducting connection (if applicable) and electrical connection in the
wall/cabinet.

3. Install an approved wire connector to the electrical knockout of the hood and guide the
electrical cable through the hood, allowing at least 6" of wire for connections and tighten.

4. Install the 4 mounting screw at the previously marked locations. Leave approximately 1/8"
clearance. Slide the shell in place through the keyhole slots and align the front of the shell
so that it is flush with the front of the cabinets. Tighten all screws securely (Figure 4).

Black

Neutral (White)

Black

Neutral (White)

Hood

Green

Ground (Green or Bare)

Supply from house

Figure 5

NOTE: DO NOT disconnect any wiring that has already been crimped with a wire connector from
the factory.

2. Install the wire compartment cover and tighten screw. Make sure all wiring is securely
contained within the wire compartment.

3. Turn switch to the “OFF” position and restore power. Test that the light is operating properly.

SECTION 5

Maintenance

CAUTION: MAKE SURE POWER IS SWITCHED OFF AT

SERVICE PANEL BEFORE SERVICING THE UNIT.

Cleaning

CAUTION: DO NOT USE GASOLINE, BENZINE, THINNER, HARSH

CLEANSERS, ETC., AS THEY MAY DAMAGE THE RANGE HOOD.

1. Clean your shell with a mild detergent, such as dishwashing liquid, and dry with a soft
cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS. Completely dry before
restoring power. NEVER IMMERSE ELECTRICAL PARTS IN WATER.

1/8"

CALIFORNIA RESIDENTS ONLY:

Keyhole

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR

CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER.

WARNING: THIS PRODUCT CAN EXPOSE YOU TO A CHEMICAL [OR

CHEMICALS] KNOWN TO THE STATE OF CALIFORNIA TO CAUSE REPRODUCTIVE
TOXICITY.

Figure 4

LIMITED WARRANTY

WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for one (1) year from the date of original purchase or until the original purchaser of the product sells or

transfers the product, whichever first occurs.

WHAT AIR KING WILL DO: During the warranty period, Air King will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model.
WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper handling or operation, shipping damage, abuse, misuse, unauthorized repairs

made or attempted. This warranty does not cover shipping costs for the return of products to Air King for repair or replacement. Air King will pay return shipping charges from Air King following warranty repairs or replacement

ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY), LAST ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL
THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY
INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING
ANYTHING TO THE CONTRARY, IN NO EVENT SHALL AIR KING’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.

Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so these exclusions or limitations may not apply to you. This
warranty gives you specific legal rights. You may also have other rights which vary from state to state and province to province. Proof of purchase is required before a warranty claim will be accepted.

CUSTOMER SERVICE:

Our Customer Service team is available to assist you with product questions, service center locations, and replacement parts. They can be reached Monday through Friday, 8am-4pm Eastern. Please have your model

PARTS FOR DISCONTINUED, OBSOLETE AND CERTAIN OTHER PRODUCTS MAY NOT BE AVAILABLE. DUE TO SAFETY REASONS, MANY ELECTRONIC COMPONENTS AND MOST HEATER COMPONENTS ARE NOT

6728041 Rev. B 2-16 2 of 2

number available, as well as the type and style (located on the label inside of your product).

AVAILABLE TO CONSUMERS FOR INSTALLATION OR REPLACEMENT.

Toll-Free [phone]

Please do not return product to place of purchase.

www.airkinglimited.com

www.airkinglimited.com