Airbagit Electrical Relay Installation Instructions
25-AMP
RELAYS - ELECTRICAL
RELAYS - ELECTRICAL
40-AMP
Back to
Store
RELAYS how they work & how to wire it up..
Many Installers do not know how relays are used.....
what is a relay?
-a relay is a device that allows you to control a high-current electrical load with a low-current electrical 'signal'. they are usually electromagnetic, but are also available in solid-state forms. they can be used
with a switch (to allow control of a high-current load with a small
switch) or they can be hooked up to a switched power source in the
car like the ignition or accessory power circuits (to allow power to be
50-AMP
switched on/off automatically with the ignition key).
Why do I need a relay?
-when hooking anything up to a car's factory wiring, it's important to
remember that factory wires are designed to carry the load of only the
factory installed components. they are not 'general use' power circuits
like the power outlets in your house. for example, the ignition (IGN)
circuit is designed to power the car's ignition system and nothing else.
60-AMP
hooking up a high-current device to this circuit can create a fire hazard. by using a relay, you can use the IGN circuit to control a high-cur-
rent device without directly powering it from the IGN circuit itself.
Is a relay hard to hook up?
-no... most relays require only 4 wires.
I bought a relay, but I don't know how to hook it up.
80-AMP
Used on small
Compressors
for overload
protection
Circuit Breaker
Weird numbers and strange symbols, what do they mean?
-a standard relay will have 4 or 5 numbered leads (30, 85,
86, 87,& sometimes 87a). why they picked those numbers, I
have no clue; but I can tell you what they hook up to.
-30 = constant [positive (+)] power wired direct to battery)
-85 = coil ground (wired to the negative (-) battery terminal
or any grounded metal panel in the car)
-86 = coil power (wired to the control source. could be a
switch, or it could be the car's IGN or ACC circuit.)
-87 = switched [positive (+)] power output. (when relay coil
is powered, lead/pin 87 is connected to lead/pin 30)
75-AMP
Used between Large Compressor
(DC7500) and Car Battery
3-Positions
-87a = [on 5 lead/pin relays only] this lead/pin is connected
to lead/pin 30 when the coil is NOT powered.
here is the bottom view of a standard 4-lead relay
Switches Must have Relays !!
Pressure Switches do not go bad, but
they burn up when you hook them up
without a relay. ALSO.. IF YOU HOOK
IT UP WRONG, THE PRESSURE
SWITCH WILL NOT SHUT OFF!!
10 Gauge Wire #30, & #87
3-Position On/Off/Neutral
FBSS Switch, use with
relay to power
ON/OFF/NEUTRAL
Returns to center automatically. Must use
Relays
3-Positions
ON/OFF/NEUTRAL
Returns to center automatically. Must use
Relays
Momentary on, re-
turns to off when
button is released
Stainless Steel Used
for Shavedoors, etc
here is what happens inside the 4-lead/pin SPST relay. on the left, the coil is
NOT powered. on the right, the coil IS powered. notice the switch changes
positions when the coil is powered. when the coil is powered, pins 30 and
87 are connected. when the coil is NOT powered, then pin 30 is not connected to anything, therefore it is in the 'off' position.
2-Position
On/Off
Switch for many
uses
Digital Sendors
used with Digital
Gauges and our
Smartride
typical setup to control power to a accessory via the car's ACC/IGN circuits.
Analog Sendors
Wiring Harness
for 8 Valves and
Pressure Switch,
with Molex Snap-
in
Connectors
Quantity Prices can be
even lower than shown
for larger quantites and
higher volume purchases
Email: joe@chassis
-
tech.com for lowest pos-
sible prices.
I want to use the relay to turn on/off with the car. how do I hook that
up?
-connect lead/pin 86 to the car's IGN, or ACC circuit. these circuits can be
tapped into in the wiring harness that goes to your car's key switch. the ACC
circuit can also be tapped into at the fuse box or in the stock radio harness.
What is the difference between ignition (IGN) and the accessory (ACC) circuit?
-they are both powered when they key is in the 'RUN' position, and they are
both not-powered when they key is in the 'OFF' position.
-the 'ACC' circuit is powered when the key is in the 'ACC' position, but is not
powered when the key is in the 'START' position. when the key is turned,
power to the relay will turn on as the key passes the 'ACC' and 'RUN' positions, then turn off in the 'START' position, then turn back on as the key is released (springs back to the 'RUN' position. this is not an issue if you're using a
manual on/off switch, or have a delayed on startup controller.
-the IGN circuit is powered when the key is in the 'START' position, but is not
powered when the key is in the 'ACC' position. this circuit avoids the issue
stated above, but requires that the key is left in the 'RU' position if you want to
use the carputer with the engine off. on some cars, this can burn out the ignition coil.
I bought a 5-pin relay, can I still use it as a simple on/off switch instead of a
changeover switch?
-yes. simply leave pin 87a disconnected.
My relay has more than 5-leads/pins?
if your relay has more than 5-leads/pins then it is most likely a DPDT, MPDT, or
MPMP relay (M=multiple). it will work the same way, it simply has two or more
separate switched inputs/outputs inside it. regardless of the number of
switched contacts, it will still use a single coil, so it will still be controlled by a
single power source.
does a relay take the place of a fuse?
-no! a relay provides no protection from overload or short-circuits.
do I need to use a fuse if I use a relay?
yes! you must still fuse your power wires!
Loading...