Aiphone KC-IFA User Manual

KC-IFA

Network Video Interface Adaptor

KCS-IFA Set includes:

KC-IFA, KC-DAR, PS-2420UL

- INSTRUCTIONS -

The KC-IFA is a network video interface adaptor that allows the Aiphone color video door station to be connected through a video server (not supplied by Aiphone) to any PC connected to a LAN or WAN network. This provides audio and video identification and access control for a person at the camera location, answered from a PC.

DOOR STATION INSTALLATION:

1. The KC-DAR should be mounted between 48-52" above finished floor, or at optimum height for the application. (See illustrations below.)

2. Install KC-DAR to 1-gang box or ring, or directly to wall surface with appropirate hardware.

3. Use 2 conductor, 18AWG non-shielded wire from KC-DAR to KC-IFA. (Aiphone #871802)

Mounting height

Unit center

150cm (5')

50cm

(20")

250cm (8'3")

130cm (4'3")

KC-DAR

Tamperproof screw & cover

Back frame

Screws supplied (2)

Single-gang box

83.5mm

(3-5/16")

The KCS-IFA System interfaces with a Network Video Server.

Aiphone has evaluated and approved the followin g manufactures’ products for use with the KC-IFA:

BRAND: MODEL: NOTES:

Inscape Data NVS-410 Two relay outputs (One for door release)

Software Included

http://www.inscapedata.com/pdf/nvs410.pdf VCS VIP 10 One relay output for door release

http://www.controlware.de/cwp/daten/PDFs/Datenblatt_VIP10.pdf NOTE: RS232 programmable relay controller can be interfaced with most video servers to control

The Tilt function of the video door station. Contact Technical Support for more information.

NVS-410

VIP10

TERMINAL DEFINITIONS:

A1/A2: KC-DAR Connection +/-: DC 24V Input BNC Connector: Video Output NO,NC,COM: Call-in Output OUT/GND: Audio Output IN/GND: Audio Input UP: Tilt Control Up (“Lo” active) DN: Tilt Control Down (“Lo” active) GND: Tilt Control Ground

SPECIFICATIONS:

Power Source: 24VDC, 1A Consumption 400mA, Max. Video Out: NTSC, 1Vp-p Audio In: 10k Ohm Audio Out: 600 Ohm Call-in Signal: N/O – COM – N/C, 24V DC@ 1A

(Present at .5 sec.; adjustable to 30 sec.) Tilt Up/Down: TTL/CMOS low level control Weight: 4.3 lbs Dimensions: 1.7"H x 7.9"W x 9"D KC-DAR to KC-IFA: 2 parallel wires, non-polarized (#871802)

22 AWG = 165', 18 AWG = 330'

Pg. 1

WIRING DIAGRM:

KC-DAR

KC-IFA

Video Server/Encoder

A1 A2

PS-2420UL

1A1 1A2

BNC

COM

OUT

GRD

UP DN

GRD

To "Video IN"

To "Sensor Input" (Contacts are activated when the call button on the door station is pressed.)

To "Audio In +" To "Audio In -" To "Audio Out +"

To "Audio Out -"

To "Tilt UP" To "Tilt DOWN" To "Tilt GND"

Connections from server to network: See server instructions.

NOTE:

If the video server used does not provide relay outputs for Tilt control, the KC-DAR will remain in a level fixed position. Upward angle adjustment can be made at the time of installation. If the video server supports RS232 for PTZ, an RS232 networkable Relay controller can be added for this function.

WIRING CONNECTIONS:

1. KC-DAR connects to KC-IFA on 1A1/1A2 terminals with 18AWG non-shielded wire.

2. Power supply (PS-2420UL) connects to KC-IFA on +/- terminals.

3. Composite video output from KC-IFA is from the BNC connector.

4. When call button on KC-DAR is pressed NO, COM, NC terminals are activated. Use proper contact (NO or NC) to connect to sensor input on video server. This will signal that the video door station has been activated.

5. OUT/GND terminals are the audio output from the video door station and connect to the audio input on the video server.

6. IN/GND terminals are the audio input from the video server to the video door station. Connect to audio output of video server.

7. UP/DN/GND terminals are for adjusting the “tilt” function of the video door station. By providing a short or relay closure to UP/GND, the camera will move up (for the duration of the closure or until it reaches the top). A short of relay closure to DN/GND will move the camera down, or to the level position.

ADJUSTMENTS:

CALL-IN CLOSURE TIME:

1. Remove KC-IFA cover.

2. Locate VR-401 (See Illustration to right)

3. Adjust VR-401 to appropriate time. VIDEO SIGNAL LEVEL:

1. Remove KC-IFA cover.

2. Locate VR-301 (See illustration to right)

3. Adjust VR-301 to appropriate level. VOICE LEVELS:

Incoming and outgoing volume levels and duplex mode can be adjusted. These adjustments would be made based on video server requirements.

VR-401

VR-301

Power On/Off Switch

Circuit Board inside KC-IFA

CP-197 (Component Side)

Audio In/Out

(High or Low)

Duplex Mode

(Half or Full)

Pg. 2

+ 1 hidden pages