83062900 0501 ©
VIDEO SENTRY COLOR TILT
AUDIO VIDEO ENTRY SECURITY INTERCOM
O AlPHONE'
MOCIgIS!
KC~1GRDj
KC~1 HRDj Sub monitor station
OPERATION MANUAL
A\ PRECAUTIONS ON OPERATIONS
This Manual and the Markings on the product contain various symbols in order
that the product can be used safely and properly, and that the installer and user
are protected from injury and property damage. The following precautions must
be thoroughly read and understood before proceeding.
WARNING Negligence could result in death or serious injury.
CAUTION Negligence could result in injury or damage to property.
Explanations of Symbols;
GENERAL PRECAUTIONS
The A mark Indicates caution
statement (Incl. danger and
warning), which Is specifically
shown Inside.
A O
GENERAL INSTRUCTIONS
The • mark indicates contents
which demands a specific action
shown inside or attached.
WARNING
A
Inside the KC-1GRD/1HRD monitor station, high voltage is present. Do not open KC-1GRD/1HRD
monitor case, as electric shock could result.
Do not change or alter KC-1GRD/1 HRD. It can cause fire or electric shock,
Keep KC-1 GRD/1 HRD away from water or any other liquid. Fire or electric shock could result.V^
Do not put any metal into KC-1 GRD/1 HRD through openings. It can cause fire, electric shock
or unit damage.
Keep AC cord of power supply from being marred or crushed. If damaged, fire or electric shock
could result. “
Do not plug or unplug with wet hands. Electric shock could
Keep AC plug away from moisture or dust. Fire could result.
Do not use any power source other than specified. Fire or electric shock could result.^0
Do not put any forcible strength on the video monitor. Damage may result.
Main monitor station
0
GENERAL PROHIBITIONS
The 0 mark Indicates contents
which prohibit a specific action
shown inside or attached.
0
DISMANTLE
PROHIBITIONS
MOISTURE
PROHIBITIONS
^ CAUTION
1. Before plugging in power supply, make sure wires are not crossed or shorted. Fire or electric
shock could result. --
2. Verify chime volume while handset is on the hook. Chime sounds from KC-1 GRD/1 HRD
speaker very loud near you, and can cause hearing damage.
3. In case of electrical storms, unplug power supply from AC outlet. It can cause fire, electric A
shock, or unit damage.
4. Do not install KC-1 GRD/1 HRD in any of the following locations, as it can cause fire, electric
shock or unit damage:
- High or extreme cold temperature area, under direct sunlight, near equipment that varies
in temperature, in front of air conditioner, inside a refrigerated area, etc.
- Places subject to moisture or humidity extremes (bathroom, cellar, greenhouse, etc.)
- Places subject to environmental conditions, such as oil, dust, chemicals, salt, etc.
- Places subject to constant vibration or impact.
- Where noise generating devices such as TV or radio are close by.
- Places subject to steam or smoke (near heating equipment or cooking surfaces)
GENERAL PRECAUTIONS
A
KC-1GRD system is not operational during a power failure.
Electrical storms can cause functional problems.
Door station is weather resistant. However, do not spray water on door station. Unit trouble may result.
In areas where broadcasting station antennas are close by, intercom system may be affected by radio
frequency interference.
KC-1 GRD system has to be kept in the distance of more than 1 m, 3'3" away from TV or radio.
- 1 -
2 SYSTEM OUTLINE & COMPONENTS
KC-1GRD, VIDEO SENTRY COLOR TILT is a 1 door - 3 monitors audio video entry security intercom,
with door reiease feature. The inside monitor station is capable of tilting door camera from 0° (straight ahead)
to max. 40° upward. Call extension speaker IER-2 is optional.
SYSTEM LAYOUT (Example)
Video door station
KC-DAR
Main monitor station
FEATURES
• Tilt camera control button. Views approximately 60cm horiz. by 124cm vert.(2"H, 4'1"V) when tilted fully
• Clear and bright image with color TFT* LCD monitor and DSP** video door station
• Hear and see before answering. Instant-On audio & video when door calls
• Door call-in with chime & video.(Video time out in approximately 30 sec.)
• Internal calling via voice with All Call.
• Monitor audio & video from door hands free. (Times out in approx. 30 sec.) • tft = Thin Film Transistor
• White LED light turns on automatically toward dusk, illuminating a caller up to 30cm(1') away ** DSP = Digital Signal Processor
Call extension
KC-1GRD
IER-2
Sub monitor station
KC-1HRD
Audio sub-master station Audio sub-master station
KC-1SD KC-1SD
Sub monitor station
KC-1HRD
I PT I : AC transformer (PT-1210N in USA)
: 24V DC power supply PS-24E
* Power supply model, quantity &
wiring may vary by market & distance
required (in the example; Up to 50m
with single PS-24E).
(*1) Whits light: In low light conditions, it
automatically turns on when camera Is active. The
light may be deactivated by setting LIGHT switch
to OFF on KC-1GRD station.
(*2) Drainage opening: Must not be covered with
caulking seal, etc.
4 OPERATIONS
---------------------------------------------
(*3) Power switch: Turn the power switch off when system
malfunctions.
(*4) Camera TILT control: Press on top/bottom of pad to
move camera up or down. Views Camera tilts max. 40°
upward.
SYSTEM VIDEO SENTRY COLOR TILT 1 door - 3 monitor system
2-
DOOR CALL-IN
ANSWER DOOR
MONITORING
oHiiv >'*
stead"' □
DOOR
□
MONITOR
Call-in is annunciated by 4-tone chime and blinking red iight.
jjlinkinS Times out in 30 seconds approximately.
Both video and audio from door are activated (Instant-On feature).
To reactivate, press MONITOR button.
Pick up handset and speak to the caller. Talk channel turns off
in approximately 2-1/2 minutes.
To reactivate, press MONITOR button again.
Note: Communication is notavaiiabie during TILT operation.
In standby mode, press MONITOR button. Image and audio from
door will be on for approximately 30 seconds.
Notes: • If the MONITOR control on the bottom of the KC-1GRD or KC-1HRD is placed
in the OFF position, no audio is heard from the door.
• Audio from the monitor will not be heard at the door until the monitor's handset
is lifted.
Press
RELEASE DOOR
s—0
CD
TILT DOOR CAMERA
up
INTERNAL CALL (All Call)
While video monitor Is on, press
on top/bottom of TILT control.
Tilt door camera as needed.
Notes:
* Video door station can not be heard
during tiit operation.
• image may vary at each extremity of
viewing area, but it is not a maifunction.
ALL CALL
CD
TRANSFER DOOR CALL
ANSWER DOOR (during
internal communication)
ANSWER DOOR
(during monitoring)
While viewing the entry, depress DOOR RELEASE (Key-marked) button.
Door strike Is activated as long as the button is held down.
Press & hold down
IMAGE VIEWING AREA
When a station places a call, pre-tone and voice announcement is heard.
All Call button blinks red. Pick up handset to reply (the light is steadily lit).
Hang up when finished.
if call Is not answered, all call announcement times out in approx. 30 sec.
Place an ALL CALL to alert the other stations of the door call. At the called station,
pick up to reply, and then press MONITOR button to connect with door.
Chime tone sounds from each receiver. Hang up both handsets to end the internal
call. Door call-in LED blinks. Answering station picks up handset again to
communicate with the door.
While monitoring handsfree, lift handset to establish communication with door station.
Speak as needed. Hang up when finished.
RECEIVE INTERNAL CALL
(during monitoring)
o
Bottom view KC-1GRD, KC-1HRD
OPTIONS
Call extension: Chime tone only is transmitted to IER-2 speaker. Volume Is adjustable to 3 positions.
MONnOR
CD
LUUn^U
12 3 4
When the pretone and voice are heard from speaker, monitoring mode is turned off.
Pick up to reply to the internal call.
CONTROLS
On the bottom of monitor stations are 4 controis (as shown to the ieft):
TINT COLOUR LIGHT
o o □
OF ON
1. TONE: Varies chime voiume to 3 positions: LOW - MiD - HiGH.
2. MONITOR: Varies door audio to 3 positions: OFF - LOW - HIGH.
3. BRIGHT: Varies brightness of monitor: DARK to BRIGHT.
4. LIGHT: With LIGHT in OFF position, white LED's will remain deactivated
(OFF - MID - HIGH on KC-1HRD).
when door calls. With LIGHT in ON position; During a low light
situation the LED's will turn on when the door calls or the MONITOR
button is pressed.
NOTE: 4: TINT, COLOUR controls: Not user-serviceable
* LIGHT: not Included In KC-1 HRD
3-
5 TECHNICAL PRECAUTIONS
---------------
6 SPECIFICATIONS
Precautions on Operations
• KC-1GRD and KC-1HRD wall-mounted may collect dust.
Clean unit as needed.
• Do not put anything on KC-1GRD or cover KC-1GRD with
cloth, etc. Fire or unit trouble could result.
• KC-1 GRD unit surface becomes warmer when It Is on, but
this is not a malfunction.
• When outside temperature lowers sharply after rain, etc., the
Inside of the camera may fog up slightly, causing a blurry
picture, but this is not a malfunction. Normal operation will be
restored when moisture dissipates.
LCD monitor
• It must be noted in advance that the TFT color LCD panel,
though manufactured with very high precision techniques.
Inevitably has a very small portion of picture elements that
are either steadily lit or not lit at all, which is not considered
a unit malfunction.
• The LCD monitor looks dark In the bright lit area, etc. Adjust
BRIGHT control to high position to increase monitor
luminosity, or reduce ambient lighting.
Before asking for repairs
In case it does not call or communicate properly, check
the followings;
1. If KC-1 GRD power switch Is turned off.
2. If cause of trouble is not found, turn off power switch, and
Contact your installing dealer for repair information.
3. When tint does not come out properly;
• Due to poor lighting on the object at night, there will be
interference in the image. This is not a malfunction.
• When gate or porch light Is fluorescent, the Image or color
may vary. This is not a malfunction.
4. Viewing image on LCD monitor
See the image right in front of the LCD monitor. When
viewed down, the image may look too bright, and when
viewed up, the image may look dim, but this is not a
malfunction.
Cleaning
Clean the KC-1 GRD units with a soft cloth dampened with
neutral household cleanser. Never use any abrasive cleaner
or cloth.
KC-1 GRD, KC-1HRD
• Power source:
• Consumption:
• Video monitor
• Power supply:
• Call-in:
• Communication:
• Ambient temperature:
• Housing:
• Color:
• Dimensions:
• Weight:
• Door release:
• Wiring:
DC 24V.
KC-1 GRD: Max. 450mA. 70mA standby.
KC-1HRD: Max. 200mA. 50mA standby.
4 inch TFT color LCD.
PS-24E (2A).
4-tone electronic chime & door call-in
LED blinking red.
Simultaneous with handset
0°C~40°C(32°F~104°F)
Fire-retardant ABS plastic
Snow white
195Hx185Wx88D(mm)
7-3/4"H X 7-1/4"W X 3-1/2"D
890g (1.96 lbs.) (approx.)
Contact rating: AC 12V, 400mA.
KC-1 GRD ~ KC-DAR: 2 wires (NP)
KC-1GRD/KC-1HRD ~ KC-1SD:
2 wires In loop plus 2 wires In same or
separate-jacketed cable(for power supply).
KC-DAR
• Power source:
• Consumption:
• Communication:
• Picture element:
• Image view area:
Max. 22V (approx.) in operation.
DC 12V (approx.) In standby.
Supplied by KC-1 GRD
Max. 350mA (approx.)
4mA (approx.) In standby
Simultaneous In open voice
1/4 inch color CCD
Horizontal 60cm (approx.)
Vertical 111 ~ 235cm (approx.)
at 130cm high (up to unit center)
and at 50cm from camera
2' H, 3' 8" ~ T 9"V at 4' 3" high at 20"
• Night viewing:
• Ambient temperature:
• Housing:
Color:
• Dimensions:
• Weight:
from camera.
White light projected up to 30cm (1') from
door camera. The background scene
beyond 30cm (1') cannot be seen
- 10°C ~ 60°C(14°F~140°F)
Fire-retardant ACS plastic
Gray
140Hx105Wx44D(mm)
5-1/2"H X 4-1/8"W X 1-3/4"D
31 Og (0.68 lbs.) (approx.)
Wiring distance
(Diameter) O.65mm0 I.Omme 1.2mm0
•KC-1GRD~KC-DAR 50m 100m
•KC-1GRD~KC-1HRD 50m 100m
•KC-1GRD-PS24 10m 20m
•KC-1GRD-IER-2 50m 100m
(KC-1SD)
22AWG 18AWG 16AWG
165' 330'
165' 330'
165' 330'
33' 65'
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instmctions, may cause harmfrd interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can he determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna. • Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. • Increase the separation between the equipment and receiver. • Consult the dealer or an experienced radio/TV technician for help.
Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of
two years after delivery to the ultimate user and will repair free of charge or replace at no charge, should It become defective
upon which examination shall disclose to be defective and under warranty. Aiphone reserves unto itself the sole right to make
the final decision whether there is a defect in materials and/or workmanship; and whether or not the product is within the
warranty.
This warranty shall not apply to any Aiphone product which has been subject to misuse, neglect, accident, or to use in violation
of instructions furnished, nor extended to units which have been repaired or altered outside of the factory. This warranty does
not cover batteries or damage caused by batteries used In connection with the unit.
This warranty covers bench repairs only, and any repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site service calls.
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE EUROPE N.V., ANTWERP, BELGIUM
KC-1GRD-0/M(E) 0501C
WARRANTY
0
COMMUNICATION SYSTEMS
AIPHONE*
HOME, BUSINESS, INDUSTRY.
Printed in Japan (E)
4-
4*
4-
4*
4*
44-
4*
4*
4-
Loading...