Aiphone KB-SWM, KB-MV3, KB-MV2, KB-SWS User Manual
KB-MV2, KB-MV3, KB-SWM, KB-SWS
Color Tilt Multi-Unit Video Entrance System
- INSTRUCTIONS -
The KB-MV series is a color video multi-unit entry system that can be configured for buildings with two to
twelve tenant locations. Up to three video entrance stations can be used in one system. The color camera can
be tilted upward for a better view of the visitor, and the speaker/microphone provides hands free
communication at the entrance panel. Inside each tenant location, the standard Aiphone KB series audio/video
stations are employed, allowing up to five monitoring locations per tenant. If there are are less than three
common entries, an individual audio-only or audio-video door station can be included for each tenant location.
KB-MV2
Microphone
Camera Lens
Night Vision LED
Speaker
KB-SWM and KB-SWS
with 2 GF-3P, 1 GF-2F
KB-MV3
Features:
Streamline design, can be semi flush mounted or surface mounted
Color CCD camera with tilt control
Configure from 2 to 12 call buttons per entry, using 1-, 2-, or 3-button modular panels
Backlit call button directory for easy viewing of names at night
Weather resistant for outdoor use
Hands free communication from entry panel
Automatic night mode LED
Employs KB series room stations
Up to three video entry stations per tenant
Up to five inside stations per tenant
Selective door release from each tenant location when using RY-3DL (one per tenant)
Easy homerun wiring from entry to each tenant using Aiphone series wire # 871802
Open position
for additional
module,
determined by
panel design.
Page 1
INSTALLATION DIAGRAM:
KB-MV2
Rear View
U
P
NOT USED
KB-SWM & KB-SWS
Rear View
3A2 3A1 2A2 2A1 1A2 1A1
To KB-3MRD
KB-SWM
To KB-3MRD
To KB-3MRD
To KB-3MRD
KB-SWS
To KB-3MRD
3A2 3A1 2A2 2A1 1A2 1A1
WHITE
BLACK
Installation:
- Mount the KB-SWM and KB-SWS into the GF-2F or GF-3F mounting bracket.
- Plug the KB-MV2 / KB-MV3 connector cable into the KB-SWM. If any KB-SWS sub-modules are used, plug the
KB-MV2 / KB-MV3 connector cable into the closest one, then plug its blue and yellow 10-pin connector into the next
switch module, daisy-chaining them together. Plug the last KB-SWS connector into the KB-SWM master switch module.
- Connect the black and white wire from the KB-MV2 / KB-MV3 connector cable to the SKK-620 power leads (cut spade
lug connectors). The white wire connects to +6VDC (black w/white stripe), and the black wire to -6VDC (solid black).
- Connect wires from KB-3MRD’s to corresponding terminals on the KB-SWM / KB-SWS. (1A1, 1A2 = upper button,
2A1, 2A2 = middle button, 3A1, 3A2 = lower button)
- Install completed entry panel into either the GF-2B / GF-3B (semi-flush mount) or GF-nHB (surface mount) as required.
- Use Aiphone series wire 871802. Wire must be 18AWG solid, non-shielded, PE insulation.
To + 6VDC
To - 6VDC
To KB-3MRD
Initialization:
- The entrance panel must be powered on prior to powering the
tenant stations.
- After the entrance and tenant stations are powered on, initialize
the system by calling each tenant from each entry panel.
GF-2F
(frame & bracket)
Page 2
(frame & bracket)
GF-3F
Not Used
1A1, 1A2
2A1, 2A2
3A1, 3A2
KB-SWM & KB-SWS’s
mounted in bracket
Loading...