Aiphone JAW-AZ User Manual
Video Modulator with Audio Door Station and CCTV Interface
- INSTRUCTIONS -
The JAW-AZ converts a standard CCTV camera's signal to a 2-wire signal, compatible with the JA Open Voice
Color Video system. This allows the utilization of a color CCTV camera and a separate audio door station (JA-D)
to be used in place of a JA video door station (Door 2 input only). Up to two additional CCTV cameras can be
connected to the JA Monitor for video only (Adapter 1 & 2 inputs). A motion detector or other activation device can
be connected to the Sensor input (in place of JA-D) to trigger the camera. Video output is pro vid ed for continual
viewing and/or recording. The unit is equipped with a relay output to trigger an external device, such as a DVR or
video switcher whenever the audio and/or video to the Aiphone moni tor is on.
SENSOR RELAY MASTER AUDIO
OUT IN
75 OHM
NC NC NO NO A1 A2 1 2
VIDEO
TERMINAL DEFINITIONS:
AUDIO 1, 2: JA-D Audio door station input (One per system, Master Door 2 input only)
MASTER A1, A2: Output from JAW-AZ to JA-2M(E)CD master input (A1,A2 or C1,C2)
RELAY NO, NO: Normally Open relay contact, activated when JA monitor is on
SENSOR NC, NC: Normally Closed contact, activates unit when tripped by motion detector or other device
with N/C contacts. (Requires “SET” mode to be active on monitor)
VIDEO IN: Composite input signal from CCTV camera
VIDEO OUT: Composite output to external CCTV monitor, switcher, DVR, video input on another device
75 OHM SWITCH: Termination Switch. Set to OFF position when VIDEO OUT is connected to CCTV system.
Set to ON position when video output is not used
OFF ON
AIPHONE
INTERNAL ADJUSTMENT WHEN JA-D AUDIO DOOR STATION IS INCLUDED:
INSTRUCTIONS:
1. Open unit by removing 5 small
screws and lifting off cover.
2. Locate Jumper labeled JP1 on
the right side of the PC board.
3. Remove the jumper completely,
or move it so it is on just one of
the posts.
4. Replace the cover and the 5
screws.
Pg. 1
WIRING DIAGRAM:
JAW-AZ Modulator for Standard CCTV Camera and Audio-only Door Station
Door 2
JA-D*
1
2
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
IMPORTANT:
Do not install JAW-AZ/JA-D on
Door 1 input.
Sensor input cannot be used
when JA-D is present.
Door 1
JA-DAC/DGC/DGV
A1
A2
JAW-AZ
MASTER
A1
A2
AUDIO
1
2
VIDEO IN
VIDEO OUT
SENSOR
NC
NC
RELAY
NO
NO
PS-2420UL
+
-
JA-2M(E)CD
Door 1
A1
A2
Door 2
A1
A2
B1
B2
+
-
JA-2HCD
SUB IN
B1
B2
SUB OUT
B1
B2
+
-
JA-2HCD
SUB IN
B1
B2
SUB OUT
B1
B2
+
-
(JA-D cannot be used when JAW-AZ
is connected to C1/C2 inputs.)
CCTV Camera
75 Ohm, 1V Peak-to-peak
(Independently powered)
Remote Activation**
(Optional, use only when
JA-D is not installed)
JAW-AZ
MASTER
A1
A2
AUDIO
1
2
VIDEO IN
VIDEO OUT
SENSOR
NC
NC
RELAY
NO
NO
Adapter 1
C1
C2
When VIDEO OUT is connected,
set 75 ohm switch to OFF position.
Constant video output for
CCTV monitor, DVR, etc.
Normally Open contact for
remote device activation
(i.e. video switcher, DVR, etc.)
NOTES:
1. JA-D is the only audio-only door
station compatible with this system.
2. Video Output is optional. If not in
use, set the 75 ohm switch to the
ON position.
3. When the SENSOR input is used,
the camera will turn on when the
sensor device is activated.
* NOTE: JA-D can only be used
when JAW-AZ is on master Door 2
input, and when JP1 is removed.
** Sensor input requires a Normal ly
Closed contact from 3rd party
supplied device (motion detector,
etc), and cannot be used when
JA-D is present.
Pg. 2
Loading...