Agilent 86100A/B Series
Plug-in Modules
Installation Guide
Installation Guide
Installation Instructions
Installation Instructions
This plug-in module is designed for use with the Infiniium DCA Agilent
86100A/B wide-bandwidth oscilloscope.
To install the module into the Infiniium DCA
1 Slide the module into an available front-panel slot.
You can remove or install a module while the instrument is in operation.
2 Finger tighten the two knurled screws on the module’s front panel.
Up to two modules can be inserted into the Infiniium DCA. All documentation
(including specifications) for this plug-in module is located in the Infiniium
DCA built-in information system (online help). To access the online help,
touch or click Contents on the Help menu.
2
Installation Guide
Installation Instructions
Using an Agilent 86100A
The following modules require that firmware revision A.03.04 or later be installed in the
Agilent 86100A/B:
83494A, Option 103 and Option 107
86102A
86103B
86105B
86107A
86111A
86111U
86113A
86115B
86116A
86116B
86117A
86117B
86118A
The firmware upgrade is enclosed in the module shipping container.
Agilent recommends that you use the latest version of firmware. To learn more about
firmware upgrades, available modules, or the Infiniium DCA, please visit our website at
http://www.agilent.com/comms/dca.
3
Installation Guide
General Safety Considerations
General Safety Considerations
This product has been designed and tested in accordance with IEC Publication 1010, Safety Requirements for Electronic Measuring Apparatus, and has
been supplied in a safe condition. The instruction documentation contains
information and warnings which must be followed by the user to ensure safe
operation and to maintain the product in a safe condition.
Install the plug-in module according to the enclosure protection provided.
This instrument does not protect against the ingress of water. This instrument
protects against finger access to hazardous parts within the enclosure.
WARNING If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.
WARNING No operator serviceable parts inside. Refer servicing to qualified
service personnel. To prevent electrical shock do not remove covers.
WARNING To prevent electrical shock, disconnect the instrument from mains
before cleaning. Use a dry cloth or one slightly dampened with water
to clean the external case parts. Do not attempt to clean internally.
CAUTION This product is designed for use in Installation Category II and Pollution
Degree 2 per IEC 1010 and 664 respectively.
4
Installation Guide
General Safety Considerations
CAUTION Electrical channel input circuits and the trigger input circuit can be damaged
by electrostatic discharge (ESD). Therefore, avoid applying static discharges
to the front-panel input connectors. Prior to connecting any coaxial cable to
the connectors, momentarily short the center and outer conductors of the
cable together. Avoid touching the front-panel input connectors without first
touching the frame of the instrument. Be sure that the instrument is properly
earth-grounded to prevent buildup of static charge. Wear a wrist-strap or heelstrap.
CAUTION Optical channel fiber-optic connectors are easily damaged when connected to
dirty or damaged cables and accessories. When you use improper cleaning and
handling techniques, you risk expensive instrument repairs, damaged cables,
and compromised measurements. Before you connect any fiber-optic cable to
the Infiniim DCA, Chapter 1 in the Infiniium DCA’s Quick Start Guide.
5
Installation Guide
Declaration of Conformity
Declaration of Conformity
6
Installation Guide
Regulatory Information
Regulatory Information
Radio-Frequency Electromagnetic Field Immunity - IEC 61000-4-3: 1995 passes
criterion B
According to IEC 61000-4-3: 1995, degradation of system noise performance may be observed in some narrow frequency ranges when a 3 V/m
radio-frequency electromagnetic field is applied to the 86100A,B mainframe
with an 86102U, 86106B, or 86107A module installed.
Radio-Frequency Electromagnetic Field Immunity - IEC 61000-4-3: 1995 passes
criterion C
According to IEC 61000-4-3: 1995, the degradation of normal performance
within the specification limits may be observed in the 86100A,B mainframe
with an 86107A module installed. The instrument software recognizes this
temporary signal degradation and warns the user that the data is suspect.
The warning prompts the user to press the Clear Display button. The user
can then resume data acquisition. This required operator intervention
results in a criterion C classification.
7
Notices
© Agilent Technologies, Inc. 2000-2002
No part of this manual may be reproduced in any form or by any means
(including electronic storage and
retrieval or translation into a foreign language) without prior agreement and written consent from Agilent Technologies,
Inc. as governed by United States and
international copyright lays.
Manual Part Number
5969-5881
Edition
First edition, September 2002
Printed in USA
Agilent Technologies, Inc.
Lightwave Division
3910 Brickway Boulevard
Santa Rosa, CA 95403, USA
Warranty
The material contained in this document
is provided “as is,” and is subject to being
changed, without notice, in future editions. Further, to the maximum extent
permitted by applicable law, Agilent disclaims all warranties, either express or
implied, with regard to this manual and
any information contained herein, including but not limited to the implied warranties of merchantability and fitness for a
particular purpose. Agilent shall not be
liable for errors or for incidental or consequential damages in connection with the
furnishing, use, or performance of this
document or of any information contained herein. Should Agilent and the
user have a separate written agreement
with warranty terms covering the material in this document that conflict with
these terms, the warranty terms in the
separate agreement shall control.
Technology Licenses
The hardware and/or software described
in this document are furnished under a
license and may be used or copied only in
accordance with the terms of such
license.
Safety Notices
CAUTION
Caution denotes a hazard. It calls attention
to a procedure which, if not correctly performed or adhered to, could result in
damage to or destruction of the product.
Do not proceed beyond a caution sign
until the indicated conditions are fully
understood and met.
WARNING
Warning denotes a hazard. It calls attention
to a procedure which, if not correctly performed or adhered to, could result in
injury or loss of life. Do not proceed
beyond a warning sign until the indicated
conditions are fully understood and met.
Restricted Rights Legend
If software is for use in the performance
of a U.S. Government prime contract or
subcontract, Software is delivered and
licensed as “Commercial computer software” as defined in DFAR 252.227-7014
(June 1995), or as a “commercial item” as
defined in FAR 2.101(a) or as “Restricted
computer software” as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Agilent Technologies’ standard
commercial license terms, and non-DOD
Departments and Agencies of the U.S.
Government will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater
than Limited Rights as defined in FAR
52.227-14 (June 1987) or DFAR 252.2277015 (b)(2) (November 1995), as applicable in any technical data.
Loading...