Aemc instruments 605 User Manual

User Manual

ENGLISH

 POWER CLAMP-ON METER

605

2

CONTENTS

RECEIVING YOUR SHIPMENT ........................................................................... 8

ORDERING INFORMATION ................................................................................ 8

1 PRESENTATION .......................................................................................... 9

1.1 THE ROTARY SWITCH ............................................................................... 10

1.2 THE FUNCTION BUTTONS ........................................................................ 11

1.3 THE DISPLAY .............................................................................................. 12

1.3.1 Display Symbols ........................................................................... 12

1.3.2 Measurement Capacity Exceeded (OL) ........................................ 13

1.4 THE TERMINALS ........................................................................................ 14

2 THE BUTTONS ........................................................................................... 15

2.1

2.2 (YELLOW) BUTTON (SECOND FUNCTION) ............................................ 16

2.3 BUTTON ............................................................................................. 16

2.4 BUTTON ............................................................................................. 17

2.4.1 Normal Mode ................................................................................ 17

2.4.2 The MAX/MIN Mode + Activation of the HOL D Mode ................... 18

2.4.3 Access to the True Inrush® Mode ( set to ) ................... 18

2.5

2.5.1 Normal Mode ................................................................................ 19

2.5.2 The Hz Function + Activation of the HOLD Mode ......................... 19

2.6 BUTTON ........................................................................................... 20

3 USE ............................................................................................................. 21

3.1 INSTALLING THE BATTERIES ................................................................... 21

3.2 TURNING THE CLAMP-ON METER ON .................................................... 21

3.3 TURNING THE CLAMP-ON METER OFF .................................................. 21

3.4 CONFIGURATION ....................................................................................... 22

3.4.1 Configuring the Maximum Resistance for Continuity .................... 22

3.4.2 Auto Power OFF ........................................................................... 22

3.4.3 Configuring the Threshold for True InRush® Measurement .......... 22

3.4.4 Default Configuration .................................................................... 23

3.5 VOLTAGE MEASUREMENT (V) ................................................................. 23

3.6 CONTINUITY TEST ............................................................................... 24

3.6.1 Lead Resistance Compensation ................................................... 25

3.7 RESISTANCE MEASUREMENT Ω ............................................................. 25

3.8 DIODE TEST ......................................................................................... 26

3.9 CURRENT MEASUREMENT (A) ................................................................ 26

3.9.1 AC Measurement .......................................................................... 26

3.9.2 DC or AC+DC Measurement ....................................................... 27

BUTTON ............................................................................................... 15

BUTTON ............................................................................................. 19

3

STARTING CURRENT OR OVERCURRENT (True InRush

3.10

MEASUREMENT ......................................................................................... 28

3.11 POWER MEASUREMENTS W, VA, VAR AND PF ....................................... 29

3.11.1 Single-Phase Power Measurement ............................................... 29

3.11.2 Balanced 3-Phase Power Measurement ....................................... 30

PHASE ROTATION MODE ............................................................... 31

3.12

3.13 FREQUENCY MEASUREMENT (HZ) ......................................................... 32

3.13.1 Frequency Measurement (V) ........................................................ 32

3.13.2 Frequency Measurement (A) ........................................................ 32

3.13.3 Frequency Measurement (W) ....................................................... 33

3.14 MEASUREMENT OF THE LEVEL OF HARMONICS (THD) AND

THE

3.14.1 Measurement of THD and Frequency of the Fundamental (V) ..... 34

3.14.2 Measurement of THD and Frequency of the Fundamental (A) ..... 34

4 SPECIFICATIONS ...................................................................................... 36

4.1 REFERENCE CONDITIONS ....................................................................... 36

4.2 SPECIFICATIONS UNDER THE REFERENCE CONDITIONS ................. 36

4.2.1 DC Voltage Measurement ............................................................. 36

4.2.2 AC Voltage Measurement ............................................................. 37

4.2.3 AC+DC Voltage Measurement ...................................................... 37

4.2.4 DC Current Measurement ............................................................. 38

4.2.5 AC Current Measurement ............................................................. 38

4.2.6 AC+DC Intensity Measurement .................................................... 39

4.2.7 True Inrush® Measurement ........................................................... 39

4.2.8 Continuity Measurement ............................................................... 40

4.2.9 Resistance Measurement ............................................................. 40

4.2.10 Diode test ...................................................................................... 40

4.2.11 Active DC Power Measurements .................................................. 41

4.2.12 Active AC Power Measurements .................................................. 41

4.2.13 Active AC+DC Power Measurements ........................................... 42

4.2.14 Measurement of Apparent AC Po wer ........................................... 43

4.2.15 Measurement of Apparent AC+DC Power .................................... 43

4.2.16 Measurement of Reactive AC Power ............................................ 43

4.2.17 Measurement of reactive AC+DC power ....................................... 44

4.2.18 Calculation of the Power Factor .................................................... 45

4.2.19 Frequency Measurements ............................................................ 45

4.2.20 Specifications in THDr .................................................................. 46

4.2.21 Specifications in THDf ................................................................... 46

4.2.22 Indication of order of the phases ................................................... 46

4.3 ENVIRONMENTAL CONDITIONS .............................................................. 47

4.4 MECHANICAL SPECIFICATIONS .............................................................. 47

4.5 POWER SUPPLY ........................................................................................ 47

4.6 COMPLIANCE WITH INTERNATIONAL STANDARDS ............................. 47

4.7 ENVIRONMENTAL VARIATIONS ............................................................... 48

FREQUENCY OF THE FUNDAMENTAL (NETWORK) ..................... 34

®

)

4

5 MAINTENANCE .......................................................................................... 49

5.1 WARNING .................................................................................................... 49

5.2 CLEANING ................................................................................................... 49

5.3 REPLACEMENT OF THE BATTERIES ...................................................... 49

6 REP AIR AN D CALIBR ATION .................................................................... 50

7 TECHNICAL AND SALES ASSISTANCE .................................................. 50

8 LIMITED WARRANTY ................................................................................ 51

9 WARRANTY REPAIRS .............................................................................. 51

5

Thank you for purchasing a Model 605 Clamp-on Meter.

For best results from your instrument and for your safety, read the enclosed
operating instructions carefully an d comply with the precautions for use. These
products must be only used by qualified and trained users.

Meanings of the symbols used on the device

CAUTION - Risk of Danger! Indicates a WARNING and that the operator

must refer to the user manual for instructions before operating the
instrument in all cases where this symbol is marked.

Risk of electric shock. The voltage at the parts marked with this symbol may
be dangerous.

Refers to a type A current sensor. This symbol signifies that application
around and removal from HAZARDOUS LIVE conductors is permitted.

1.5 V battery

The CE marking indicates compliance with European directives

Double insulation or reinforced insulation
In the European Union, this product is subject to a separate collection

system for recycling electrical and electronic components In accordance
with directive WEEE 2002/96/EC

AC – Alternating current
AC and DC – Alternating and direct current
Ground/Earth

6

PRECAUTIONS FOR USE

This device complies with safety standards IEC-61010-1 and 61010-2-032 for voltages of
1000V in category IV at an altitude of less than 2000m, indoors, with a degree of pollution
not exceeding 2.
These safety instructions are intended to ensure the safety of persons and proper operation
of the device.

 The operator and/or the responsible authority must carefully read and clearly

understand the various precautions to be taken in use.

 If this instrument is used other than as specified, the protecti on it provides may be

compromised, thereby endangering you.

 Do not use the instrument in an explosive atmosphere or in the presence of flammable

gases or fumes.

 Do not use the instrument on networks of which the voltage or category exceeds those

mentioned.

 Do not exceed the rated maximum voltages and currents between terminals or with

respect to earth.

 Do not use the instrument if it appears to be damaged, inc omplete, or not properly

closed.

 Before each use, check the condition of the insulation on the leads, housing, and

accessories. Any element of which the insulation is deteriorated (even partiall y) must
be set aside for repair or scrapped.

 Use leads and accessories rated for voltages and categories at least equal to those of

the instrument. If not, an accessory of a lower category lowers the category of the
combined Clamp + accessory to that of the accessory.

 Observe the environmental conditions of use.
 Do not modify the instrument and onl y use factory replacement parts. Repairs and

adjustments must be done by approved qualified personnel.

 Replace the batteries as soon as the symbol app ears on the display of the unit.

Disconnect all leads before opening the battery compartment cover.

 Use personal protective equipment when conditions require.
 Keep your hands away from the unused terminals of the instrument.
 When handling the test probes, alligator clips, and clamp ammeters, keep your fingers

behind the physical guard.

 As a safety measure, and to avoid repeated overloads on the inputs of the device,

configuration operations should only be performed when the device is disconnected
from all dangerous voltages.

7

MEASUREMENT CATEGORIES

Definitions of the measurement categories:
CAT II: Circuits directly connected to the low-voltage installation.

Example: power supply to household electrical appliances and portable tools.

CAT III: Power supply circuits in the installation of the building.

Example: distribution panel, circuit-breakers, fixed industrial machines or
devices.

CAT IV: Circuit s supplying the low-voltage instal lation of the building.

Example: power lines, meters, and protection devices.

RECEIVING YOUR SHIPMENT

Upon receiving your ship m ent, make sure that the contents are consistent with the
packing list. Notify your d istributor of any missing it ems. If the equipm ent appears
to be damaged, file a cla im immediat ely with t he carrier a nd notif y your distrib utor
at once, giving a detailed desc ription of any d amage. Save t he damaged pack ing
container to substantiate your claim.

ORDERING INFORMATION

Clamp-on Meter Model 605 .......................................................... Cat. #2139.60

Includes set of 2 color-coded silicone insulated te st leads, test probes and alligator clips,
soft carrying case, 4x1.5V AA batteries and user manual.

Replacement Parts:

Soft Carrying Case ........................................................................................... Cat. #2139.72

Set of 2 Color-coded Silicone Test Leads, Test Probes & Alligator Clips ........ Cat. #2152.05

8

1

3

2

7

ring marks

1 PRESENTATION

The Clamp-on Meter Model 605 is a prof essional electrical measuring ins trument
that combines the following funct i ons :

 Current measurement
 Measurement of InRush current / overcurrent (True InRush
 Voltage measurement
 Frequency measurement
 Measures harmonic distortion (THD)
 Continuity test with buzzer
 Resistance measurement
 Diode test
 Power measurements (W, VA, var and PF)
 Phase order indication

Item

Jaws with cente

1

(see connection principles)

2 Physical Guard ­3 Rotary Function Switch 1.1
4 Function Buttons 2
5 Backlit Display 1.3

4

5

6 Input Terminals 1.4
7 Trigger -

Designation See §

®

)

3.5 to

3.12

6

Figure 1: Clamp-on Meter Model 605

9

1 2 3 4 5

6

1.1 THE ROTARY SWITCH

The rotary switch has six positions. To access the , , , ,
functions, set the switch to th e desired function. The functi ons are described in
the table below.

Figure 2: The Function Rotary Sw itch

Item Function See §

1 OFF mode – Turns the clamp-on meter off 3.3
2 AC, DC, AC+DC voltage measurement (V) 3.5
3 Continuity test

Resistance measurement Ω

Diode test
4 AC, DC, AC+DC current measurement (A) 3.9
5 Power measurements (W, var, VA) and calculation of the

power factor (PF) AC, DC, AC+DC

6

Phase rotation order indicator -

3.6

3.7

3.8

3.11

3.12

10

1.2 THE FUNCTION BUTTONS

1 2 3

4 5 6

Figure 3: The Function Buttons

Item Function See §

1 Holds the last value on the display

Zero correction A

Lead resistance compensation in the continuity and
ohmmeter functions

2 Selects the type of measurement and configuration

functions (AC, DC, AC+DC)

Selection of single-phase or 3-phase measurement
3 Enables/disables display backlighting 2.3
4 Enables/disables the MAX/MIN/PEAK mode

Enables/disables the True InRush

measurement (A)

5 Performs Frequency measurements (Hz) and selects

measurement of harmonic distortion (THD)

Display of the powers W, VA, var and PF
6 Activation of ΔREL mode – Displays differential and

relative values

DC/AAC+DC/WDC/WAC+DC

®

mode in current

2.1

3.9.2

3.6.1

2.2

2.4

2.5

2.6

11

AC+DC

Alternating and direct current or voltage

∆

∆

PEAK+

Maximum peak value

4

1.3 THE DISPLAY

7

1

2

3

5

Figure 4: The Display

Item Function See §

1 Mode selection display 2
2 Display of the measurement value and unit 3.5 to 3.12
3 Display of the MAX/MIN/PEAK modes 2.4
4 Type of measurement (AC or DC) 2.2
5 Total 3-phase power measurements 3.11.2
6 Selected resistance mode display 1.1
7 Low battery indication 5.3

1.3.1 Display Symbols

Symbol Designation

6

AC Alternating current or voltage
DC Direct current or voltage

REL

Ref

Relative value, with respect to a reference
Reference value
Storage of the values and display hold

Max Maximum DC or RMS value

Min Minimum DC or RMS value

12

PEAK-

Minimum peak value

Balanced total 3-phase power measurement

W

Watt

var

Reactive power

VA

Apparent power

PF

Power factor

THDf

Total harmonic distortion with respect to the fundamental

Total harmonic distortion with respect to the true RMS

V Volt

Hz Hertz

A Ampere

% Percentage

Ω Ohm

m Milli- prefix

k Kilo- prefix

THDr

value of the signal.

Phase order indication

Lead resistance compensation
Continuity test
Diode test
Auto Power Off disabled
Low battery indicator

The display of “rdy”, for “ready”, indicates that the device is ready (Phase Order
Indication function).

1.3.2 Measurement Capacity Exceeded (OL)

The OL (Over Load) symbol is displayed when the display capacity is exceeded.

13

1.4 THE TERMINALS

The terminals are used as follows:

1 2

Figure 5: The Terminals

Item Function

1

COM (black) Input Terminal Jack

2 + Positive (red) Input Terminal Jack

14

ADC

W

AC+DC

This mode operates if the MAX/MIN or

2 THE BUTTONS

The buttons respond differently to short, long, and sustained presses.
The , and keys provide additional functions as well as the

detection and acquisition of parameters complementary to the basic
measurements.

• Each of these buttons can be used independently of the others or in
conjunction with each other. T his makes navigation simple and intuit ive
when reviewing measurement result s.

• It is possible, for ex ample, to either look up i n sequence the MAX, MIN,
etc. values of the RMS voltage alone, or l ook up in sequence all of the
MAX (or MIN, or PEAK) values of all power measurements (W, VA, var,
etc.).

In this section, the icon represents the possible posi tions of the switch for the
button’s functionality.

2.1

BUTTON

This button is used to:

 Store and look up the last values acquired specific to each funct ion (V, A,

Ω, W) according to the specific modes previously activated (MAX/MIN).

The present display is then maintai ned while the detection and acquisition
of new values continues.

 Perform automatic lead resistance compensat ion (see § 3.6.1).
 Perform automatic zero correction in

ADC/

NOTE: This button is invalid for the Phas e Order Indication function.

Successive

presses on

long

(> 2 sec)

long

(> 2 sec)

A

AC+DC

W

DC

First press: Holds the last value displayed

Second press: Returns to normal display mode

(the value of each new measurement is
displayed)

Performs automatic zero correction (see 3.9.2)
NOTE:

HOLD modes (short press) are first de activated

Performs automatic lead resistance
compensation (see 3.6.1)

See § 2.4.2 and § 2.5.2 for the button functionality in com bination with the

and buttons.

AC+DC

Function

and WDC/

(see § 3.9.2).

AC+DC

15

2.2 (YELLOW) BUTTON (SECOND FUNCTION)

This button is used to select the t ype of m easureme nt (AC, DC, AC+DC) and the
second functions marked in yellow ne xt to the relevant positions of the switch.

It can also be used to modify the default values in the configuration mode
(see § 3.4).

NOTE: This button is invalid in the MAX/MIN/PEAK, HOLD and ΔREL modes.

Successive

presses on

short

long (>2 sec)

- Selects AC, DC or AC+DC. Depending on
your choice, the screen displays AC, DC or
AC+DC

- Cycles through the continuity , Ω and
diode test modes and returns to the
continuity test

- Resets the measurement process for the
phase order indication function

- Displays the total 3-phase power of a
balanced system ( is displayed). Press
again to return to the display of the single­phase power ( is off)

Function

2.3 BUTTON

Successive

presses on

- Enables/disables display backlighting

NOTE: The backlighting is automatically disabled at the end of 2 minutes.

16

Function