AEM 30-3509 Infinity Plug Play Harnesses User Manual

Page 1

Instruction

STOP!

THIS PRODUCT HAS LEGAL RESTRICTIONS.

READ THIS BEFORE INSTALLING/USING!

THIS PRODUCT MAY BE USED SOLELY ON VEHICLES USED IN SANCTIONED COMPETITION WHICH MAY NEVER BE USED UPON A PUBLIC ROAD OR HIGHWAY, UNLESS PERMITTED BY SPECIFIC REGULATORY EXEMPTION. (VISIT THE “EMISSIONS” PAGE AT HTTP://WWW.SEMASAN.COM/EMISSIONS FOR STATE BY STATE DETAILS.)

IT IS THE RESPONSIBILITY OF THE INSTALLER AND/OR USER OF THIS PRODUCT TO ENSURE THAT IT IS USED IN COMPLIANCE WITH ALL APPLICABLE LAWS AND REGULATIONS. IF YOU HAVE PURCHASED THIS PRODUCT IN ERROR, DO NOT INSTALL AND/OR USE IT. PLEASE CONTACT THE RETAILER FROM WHOM YOU PURCHASED THE PRODUCT TO ARRANGE A RETURN FOR A FULL REFUND OR VISIT

AEMELECTRONICS.COM/PRODUCT-LEGAL-RESTRICTIONS FOR FURTHER INSTRUCTIONS.

Manual

P/N 30-3509

1999–2001 Honda B-H-D Series OBD2b

Infinity-6 and Infinity-8h*

Plug & Play Adapter Harness

WARNING: This installation is not for the tuning novice! Use this system with EXTREME caution! The AEM Infinity Programmable EMS allows for total flexibility in engine tuning. Misuse or improper tuning of this product can destroy your engine! If you are not well versed in engine dynamics and the tuning of engine management systems DO NOT attempt the installation. Refer the installation to an AEM-trained tuning shop or call 800-423-0046 for technical assistance.

NOTE: All supplied AEM calibrations, Wizards and other tuning information are offered as potential starting points only. IT IS THE RESPONSIBILITY OF THE ENGINE TUNER TO ULTIMATELY CONFIRM IF THE CALIBRATION IS SAFE FOR ITS INTENDED USE. AEM holds no responsibility for any engine damage that results from the misuse or mistuning of this product!

*See next page for important information regarding the use of this harness with Infinity-8h

AEM Performance Electronics, 2205 126th Street Unit A, Hawthorne, CA 90250

AEM Performance Electronics

Phone: (310) 484-2322 Fax: (310) 484-0152

http://www.aemelectronics.com

Instruction Part Number: 10-3509

Document Build 8/25/2014

Page 2

P/N 30-3509

OVERVIEW

The 30-3509 AEM Infinity Adapter Kit was designed for the 1999–2001 Honda B-H-D Series OBD2b. This is a true standalone system that eliminates the use of the factory ECU. The use of this adapter makes the kit “plug and play” so no cutting or splicing wires is necessary. The base configuration files available for the Infinity EMS are starting points only and will need to be modified for every specific application.

The available AEM Infinity EMS part numbers for this adapter kit are:

30-7106 INFINITY-6 30-7108 INFINITY-8h

GETTING STARTED

Refer to the 10-7100 for EMS 30-7100 Infinity Quick Start Guide for additional information on getting the engine started with the Infinity EMS. The base session is located in C:\Documents\AEM\Infinity Tuner\Sessions\Base Sessions

DOWNLOADABLE FILES

Files can be downloaded from www.aeminfinity.com. An experienced tuner must be available to configure and manipulate the data before driving can commence. The Quick Start Guide and Full Manual describe the steps for logging in and registering at www.aeminfinity.com. These documents are available for download in the Support section of the AEM Electronics website: http://www.aemelectronics.com/

products/support/instructions.

Downloadable files for 1999–2001 Honda B-H-D Series OBD2b

OPTIONS

30-3501-00 Honda Coil Adapter

Ignition adapter to drive factory Honda distributor internal coil. REQUIRED for use with Honda distributor if not converting to a sequential coil-on-plug setup

30-2001 UEGO Wideband O2 Sensor

Bosch LSU4.2 Wideband O2 Sensor that connects to AEM 30-3600 UEGO Wideband O2 Sensor Extension Harness

30-3600 UEGO Wideband O2 Sensor Extension Harness

Extension harness to connect AEM UEGO Wideband O2 sensor to 6-pin Deutsch

30-3602 IP67 Logging Cable

USB A-to-A extension cable: 39” long with right angled connector and bayonet style lock

7106-XXXX-75 (for 30-7106, INFINITY-6) (XXXX = serial number) 7108-XXXX-76 (for 30-7108, INFINITY-8h) (XXXX = serial number)

Page 3

1999–2001 Honda B-H-D Series OBD2b

Infinity Pin

Infinity-6 Function

Infinity-8h Function

30-3509 PnP Honda Pin

Notes C1-3

Lowside6

Injector7

B16

LS6/IAB on Infinity-6 or Injector7 on Infinity-8h

C1-4

Lowside7

Injector8

Available LS7 on Infinity-6 or Injector8 on Infinity-

C1-31

Digital6

Coil7

Aux - 6

Turbo Speed [Hz] input on Infinity-6.

** Must de-pin for use with Infinity-8h, Coil7 not used**

C1-32

Digital7

Coil8

Unpopulated

Available Digital7 on Infinity-6, Coil8 not used on

Infinity-8h.

*IMPORTANT INFINITY-8H INFORMATION

The primary difference between the 30-7106 Infinity-6 and 30-7108 Infinity-8h is that the 8h lacks Peak & Hold injector drivers to run low impedance fuel injectors. High impedance (saturated, high-z) fuel injectors must be used with the Infinity-8h.

The Infinity-6 and Infinity-8h share a common pinout with the exception of four pins where the Infinity-8h has two each additional fuel injector and ignition coil drivers. Due to the additional fuel injector and ignition coil drivers, the 8h has two fewer digital inputs and lowside outputs. Use of this harness with an Infinity-8h will require slight modification and could result in loss of some plug and play function.

INFINITY CONNECTORS

The AEM Infinity EMS uses the MX123 Sealed Connection System from Molex. AEM strongly recommends that users become familiar with the proper tools and procedures for working with these high density connectors before attempting any modifications. The entire Molex MX123 User Manual can be downloaded direct from Molex at:

http://www.molex.com/mx_upload/family// MX123UserManual.pdf

Page 4

P/N 30-3509

INFINITY ADAPTER HARNESS

Included with the 1999–2001 Honda B-H-D Series OBD2b kit is an adapter harness. This is used to make the connection between the AEM Infinity EMS and the Honda wiring harness plug and play. This is depicted below with the 80-pin connector and the Honda header. There are also a few other integrated connectors within this harness described below.

The gray Deutsch 6P DTM “LAMBDA” connector is for connecting a UEGO wideband Bosch LSU4.2 sensor (AEM 30-2001). The UEGO extension harness (AEM 30-3600) mates the adapter harness to the sensor.

The gray Deutsch 6P DTM “COIL” connector is for ignition output. Using with the included jumper connector runs distributor application. Coil-on-Plug conversion requires some custom wiring and setup with Infinity tuner software.

The gray Deutsch 6P DTM “LAMBDA” connector is for connecting a UEGO wideband Bosch LSU4.2 sensor (AEM 30-2001). The UEGO extension harness (AEM 30-3600) mates the adapter harness to the sensor.

The gray Deutsch 6P DTM “COIL” connector is for ignition output. This connector has been configured to allow the triggering of four individual coils by interfacing with this connector. AEM offers the 30-3501-00 Honda Coil Adapter for use with the OEM Honda distributor’s internal coil. This adapter is required if the OEM distributor and ignition coil are to be used.

Page 5

1999–2001 Honda B-H-D Series OBD2b

The gray Deutsch 4P DTM connector is used for “AEMNET”. AEMNet is an open architecture based on CAN 2.0 which provides the ability for multiple enabled devices, such as dashboards, data loggers, etc., to easily communicate with one another through two twisted cables (CAN+/CAN-).

The black Delphi 2-pin “FLASH” connector is used for secondary hardware flashing. The included shunt connector jumps the 2 wires together. Once initially flashed, the EMS is normally upgraded in the software, not using this connector.

The gray Deutsch 12P DTM “AUX” connector is used to adapt many common ancillary inputs and outputs easily. Included in the kit are a DTM 12P mating connector, 12 DTM terminals, and a DTM 12P wedgelock. If used, these components will need to be terminated by the installer or end user with 16–22awg wire (not included). Note: The pin numbering is molded into the connector, as shown.

Page 6

30-7106 Infinity-6

30-7108 Infinity-8h

30-3509 Adapter

Harness

EPM Harness

COP Harness

Coil 1

C1-14

Coil Connector - 1

Orange

Coil 2

C1-13

Coil Connector - 2

Blue

Coil 3

C1-12

Coil Connector - 3

Pink

Coil 4

C1-11

Coil Connector - 4

Gray

Cam

C1-26

White

Crank

C1-25

Green

Pwr

Gnd

C1-33, C1-43, C1-

46, C1-67

C1-33, C1-43, C1-

46, C1-67

C1-46, C1-68

Drain

Sw +12

C1-63, C1-68

Aux Connector - 8

Red

Sensor

Gnd

C1-23, C1-24

Aux Connector - 3

Black

P/N 30-3509

30-2860 HONDA B-SERIES COIL-ON-PLUG CONVERSION KIT

The 30-3509 AEM Infinity Adapter Kit is ideal for use with AEM’s Honda B-Series Coil-on-Plug conversion kit. Refer to the table below for pin locations to cross reference with the 30-2860 COP Conversion Kit instruction manual.

Once the appropriate wiring connections have been made, use the Infinity Tuner Setup Wizard to configure the ECU to run with the AEM EPM and for sequential COP coil triggers. There are no jumper changes required as with AEM Series1 and Series 2 ECUs.

Setup Wizard

Engine

Ignition Type = Sequential (Coil on Plug) Firing Order = 1-3-4-2

Cam/Crank

AEM EPM (Engine Position Module)

Ignition Sync: Follow instructions in AEM Infinity Quick Start Guide for proper ignition sync procedure.

Page 7

PINOUTS

Dedicated

Dedicated and not reconfigurable

Assigned

Assigned but reconfigurable

Available

Available for user setup

Not Applicable

Not used in this configuration

Required

Required for proper function

Infinity

Assignment

Honda

Honda Description

Infinity Hardware

Specification

Notes

LS 4

A17

A/C Clutch Relay

Lowside switch, 4A max, No

internal flyback diode.

See Setup Wizard Page "LowSide Assignment Tables" for output assignment and 2D table "LS4_Duty [%]" f or on/of f activation.

LS 5

A19

Engine Speed Pulse

Lowside switch, 4A max with

internal flyback diode. Inductiv e

load should NOT hav e f ull time

power.

The tachometer is pre-calibrated using a combination of the LS5_Freq [Hz] 1-axis table and the LS5_Duty [%] 2-axis table.

LS 6

B16*

---

Lowside switch, 4A max with

internal flyback diode. Inductiv e

load should NOT hav e f ull time

power.

See Wizard page "LowSide Assignment Tables" for output assignment. *Spare injector output Injector 7 for Inf inity 8h.

LS 7

D2*

---

Lowside switch, 4A max, No

internal flyback diode.

See Wizard page "LowSide Assignment Tables" for output assignment. *Spare injector output Injector 8 for Inf inity 8h.

UEGO1

Heat

---

Bosch UEGO controller

Lowside switch f or UEGO heater control. Connect to pin 4 of Bosch UEGO sensor. NOTE that pin 3 of the Sensor is heater (+) and must be power by a f used/switched 12V supply.

UEGO1 IA

---

Bosch UEGO controller

Trim Current signal. Connect to pin 2 of Bosch UEGO sensor

UEGO1 IP

---

Bosch UEGO controller

Pumping Current signal. Connect to pin 6 of Bosch UEGO sensor

UEGO1 UN

---

Bosch UEGO controller

Nernst Voltage signal. Connect to pin 1 of Bosch UEGO sensor

UEGO1 VM

---

Bosch UEGO controller

Virtual Ground signal. Connect to pin 5 of Bosch UEGO sensor.

+12V Perm

Power

B21

Voltage Back Up

Dedicated power management

CPU

Full time battery power. MUST be powered before the ignition switch input is triggered.

Coil 4

Ignition Coil Pulse No. 4

25 mA max source current

0–5V f alling edge f ire. Do NOT connect directly to coil primary . Must use an ignitor or CDI that accepts a falling edge fire signal.

Coil 3

Ignition Coil Pulse No. 3

25 mA max source current

0–5V f alling edge f ire. Do NOT connect directly to coil primary . Must use an ignitor or CDI that accepts a falling edge fire signal.

Infinity Pinouts

1999–2001 Honda B-H-D Series OBD2b

Page 8

Infinity

Assignment

Honda

Honda Description

Infinity Hardware

Specification

Notes

Coil 2

Ignition Coil Pulse No. 2

25 mA max source current

0–5V f alling edge f ire. Do NOT connect directly to coil primary . Must use an ignitor or CDI that accepts a falling edge fire signal.

Coil 1

B13

Ignition Coil Pulse No. 1

25 mA max source current

0–5V f alling edge f ire. Do NOT connect directly to coil primary . Must use an ignitor or CDI that accepts a falling edge fire signal.

---

---16---

---

VR0 (+) -

Crank

CKP -

Dif f erential Variable Reluctance

Zero Cross Detection

See Setup Wizard page Cam/Crank f or options.

VR0 (-) -

Crank

CKP +

Dif f erential Variable Reluctance

Zero Cross Detection

See Setup Wizard page Cam/Crank f or options.

VR1 (-) -

Cam

C29

TDC1 +

Dif f erential Variable Reluctance

Zero Cross Detection

See Setup Wizard page Cam/Crank f or options.

VR1 (+) -

Cam

C30

TDC1 -

Dif f erential Variable Reluctance

Zero Cross Detection

See Setup Wizard page Cam/Crank f or options.

LS 2

A20

Radiator Fan Control

Lowside switch, 4A max, No

internal flyback diode.

See Setup Wizard Page "LowSide Assignment Tables" for output assignment and 2D table "LS2_Duty [%]" f or on/of f activation.

LS 3

B23

Idle Air Control Valv e

Lowside switch, 4A max with

internal flyback diode. Inductiv e

load should NOT hav e f ull time

power.

See Setup Wizard page and corresponding Tables f or Idle Air Control.

Sensor

GND

Sensor Ground 1

Dedicated analog ground

Analog 0–5V sensor ground

Sensor

GND

C18

Sensor Ground 2

Dedicated analog ground

Analog 0–5V sensor ground also found on aux connector

Digital 0 -

Crank

---

10K pullup to 12V. Will work with

ground or floating switches.

Not used for this application

Digital 1 -

Cam1

---

10K pullup to 12V. Will work with

ground or floating switches.

Not used for this application

Digital 2 -

Cam2

---

10K pullup to 12V. Will work with

ground or floating switches.

Not used for this application

Digital 3 –

Flex Fuel

---

10K pullup to 12V. Will work with

ground or floating switches.

Found on the Aux Connector. Input can be assigned to different pins. See Setup Wizard page Input Function Assignments for input mapping options.

Digital 4 -

VSS#1

C23

Vehicle Speed Sensor

10K pullup to 12V. Will work with

ground or floating switches.

See Setup Wizard page Vehicle Speed for calibration constant.

Digital 5 -

A27

A/C Switch Signal

10K pullup to 12V. Will work with

ground or floating switches.

See Setup Wizard Input Function Assignments page for A/C activ ation.

Digital 6 –

Turbo Speed

---

10K pullup to 12V. Will work with

ground or floating switches.

Found on the Aux Connector. Input can be assigned to different pins. See Setup Wizard page Input Function Assignments for input mapping options. *Coil 7 f or Infinity 8h.

Digital 7 -

---

10K pullup to 12V. Will work with

ground or floating switches.

Input can be assigned to dif ferent pins. See Setup Wizard page Input Function Assignments f or input mapping options. *Coil 8 f or Infinity 8h

P/N 30-3509

Page 9

1999–2001 Honda B-H-D Series OBD2b

Infinity

Assignment

Honda

Honda Description

Infinity Hardware

Specification

Notes

GNDB2Power Ground 1

Power Ground

Connects to chassis ground and AEMNet

CAN A -

---

Dedicated High Speed CAN

Transceiv er

4P DTM Connector found in AEM adapter harness. Contact AEM f or additional information.

CAN A +

---

Dedicated High Speed CAN

Transceiv er

4P DTM Connector found in AEM adapter harness. Contact AEM f or additional information.

CAN B -

---

Dedicated High Speed CAN

Transceiv er

Not used

CAN B +

---

Dedicated High Speed CAN

Transceiv er

Not used

Temp 1 -

Coolant

Temp

C26

Engine Coolant Temp

Sensor

12 bit A/D, 2.49K pullup to 5V

See "Coolant Temperature" Setup Wizard for selection.

Temp 2 - Air

Temp

(Manifold)

C25

Intake Air Temp Sensor

12 bit A/D, 2.49K pullup to 5V

See "Air Temperature" Setup Wizard f or selection.

Temp 3 - Oil

Temp

---

12 bit A/D, 2.49K pullup to 5V

Found on the Aux Connector. 0–5V analog signal.

LS 0

A16

Fuel Pump Relay

Lowside switch, 4A max, No

internal flyback diode.

Switched ground. Will prime for 2 seconds at key on and activ ate if RPM > 0.

LS 1

---

Lowside switch, 4A max with

internal flyback diode. Inductiv e

load should NOT hav e f ull time

power.

Found in Aux Connector. See Setup Wizard page Boost Control for options. Monitor BoostControl [%] channel for output state.

GND

B10

Power Ground 2

Power Ground

Connect directly to battery ground.

Knock 0C3Knock Sensor

Dedicated knock signal

processor

See Knock in Setup Wizard for options.

Knock 1

Dedicated knock signal

processor

See Knock in Setup Wizard for options.

GND

Power Ground

Connect directly to battery ground.

12V_Relay _

Control

---

0.7A max ground sink f or external relay control

Connects to relay f ound in AEM adapter. Will activ ate at key ON and at key OFF according to the configuration settings.

+12V SW

(Ign Switch)

Power Source 1

10K pulldown

Full time battery power must be av ailable at infinity pin 10 before this input is triggered.

+5V_Out

C19

Sensor Voltage 1

Regulated, f used +5V supply

for sensor power

Analog sensor power and found on auxiliary connector

+5V_Out

C28

Sensor Voltage 2

Regulated, f used +5V supply

for sensor power

Analog sensor power

Ana7 -

Throttle

C27

Throttle Position Sensor

12 bit A/D, 100K pullup to 5V

0–5V analog signal. Do not connect signals referenced to +12V as this can permanently damage the ECU. See the Setup Wizard Set Throttle Range page for automatic min/max calibration.

Ana8 - Map

C17

MAP Sensor

12 bit A/D, 100K pullup to 5V

0–5V analog signal. See the Manifold Pressure in Setup Wizard for setup and calibration.

Ana9 - Fuel

Press

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal f ound on the Auxiliary Connector

Page 10

Infinity

Assignment

Honda

Honda Description

Infinity Hardware

Specification

Notes

VR2 (+) -

Driv en

Wheel

---

Dif f erential Variable Reluctance

Zero Cross Detection

See Driven Wheel Speed Calibration in the Setup Wizard Vehicle Speed page.

VR2 (-) -

Driv en

Wheel

---

Dif f erential Variable Reluctance

Zero Cross Detection

See Driven Wheel Speed Calibration in the Setup Wizard Vehicle Speed page.

VR3 (-) -

Tag Wheel

---

Dif f erential Variable Reluctance

Zero Cross Detection

See Non Driv en Wheel Speed Calibration in the Setup Wizard Vehicle Speed page.

VR3 (+) -

Tag Wheel

---

Dif f erential Variable Reluctance

Zero Cross Detection

See Non Driv en Wheel Speed Calibration in the Setup Wizard Vehicle Speed page.

HS Out 0

B12

VTEC solenoid Valve

0.7A max, High Side Solid State Relay

+12V High Side Drive. See Setup Wizard Honda VTEC page f or options.

Stepper_1B

---

Automotive, Programmable

Stepper Driver, up to 28V and

±1.4A

Be sure that each internal coil of the stepper motor is properly paired with the 1A/1B and 2A/2B ECU outputs. Supports Bi-Polar stepper motors only.

Stepper_2B

---

Automotive, Programmable

Stepper Driver, up to 28V and

±1.4A

Be sure that each internal coil of the stepper motor is properly paired with the 1A/1B and 2A/2B ECU outputs. Supports Bi-Polar stepper motors only.

HBridge0_0

---

5.0A max Throttle Control Hbridge Drive

HBridge0_1

---

5.0A max Throttle Control Hbridge Drive

+12V

---

Main Power

12 v olt power f rom relay powers the Inf inity, Lambda sensor, and AEMNet

Injector 6

B19*

---

Saturated or peak and hold, 3A

max continuous

Spare injector output Injector 6 *No peak and hold injector for Infinity 8h

Injector 5

D1*

---

Saturated or peak and hold, 3A

max continuous

Spare injector output Injector 5 *No peak and hold injector for Infinity 8h

Injector 4 B5Injector 4

Saturated or peak and hold, 3A

max continuous

Injector 4 *No peak and hold injector for Infinity 8h

GND

---

Power Ground

Connect directly to ground.

+12V

---

Main Power

12 v olt power f rom relay powers the Inf inity

Ana19 -

APP2

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal. Do not connect signals referenced to +12V as this can permanently damage the ECU.

Ana18 -

APP1

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal. Do not connect signals referenced to +12V as this can permanently damage the ECU.

Ana16

- Mode SW

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal. Use +5V Out pins as power supply and Sensor Ground pins as the low reference. Do not connect signals referenced to +12V as this can permanently damage the ECU. See the 1D lookup table 'Mode Switch' for input state. Also assignable to multiple functions. See Setup Wizard for details.

P/N 30-3509

Page 11

1999–2001 Honda B-H-D Series OBD2b

Infinity

Assignment

Honda

Honda Description

Infinity Hardware

Specification

Notes

Harness_Fl ash_Enable

---

10K pulldown

Not usually needed for automatic f irmware updates through Inf inity Tuner. If connection errors occur during update, jump the 12V Flash Connector before proceeding with upgrade. Disconnect the 12V Flash Connector after the update.

Ana13 - Oil

Press

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal f ound on the Auxiliary Connector

Ana11 -

Shift SW

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal f ound on the Auxiliary Connector

Ana10

---

12 bit A/D, 100K pullup to 5V

0–5V analog signal f ound on the Auxiliary Connector

Injector 3 B4Injector 3

Saturated or peak and hold, 3A

max continuous

Injector 3 *No peak and hold injector for Infinity 8h

Injector 2 B3Injector 2

Saturated or peak and hold, 3A

max continuous

Injector 2 *No peak and hold injector for Infinity 8h

Injector 1

B11

Injector 1

Saturated or peak and hold, 3A

max continuous

Injector 1 *No peak and hold injector for Infinity 8h

Stepper_2A

---

Automotive, Programmable

Stepper Driver, up to 28V and

±1.4A

Be sure that each internal coil of the stepper motor is properly paired with the 1A/1B and 2A/2B ECU outputs. Supports Bi-Polar stepper motors only.

Stepper_1A

---

Automotive, Programmable

Stepper Driver, up to 28V and

±1.4A

Be sure that each internal coil of the stepper motor is properly paired with the 1A/1B and 2A/2B ECU outputs. Supports Bi-Polar stepper motors only.

Deutsch Pin

Infinity Pin

Wire Color

Pin Name

Default Pin Function

153Black

Analog 9

Fuel Pressure

240Black

Analog_In_Temp_3

Oil Temperature

323Black

AGND

Sensor Ground

449Black

+5V_OUT

Sensor +5V

573Black

Analog_In_13

Oil Pressure

631Black

Digital_In_6

Turbo Speed (Hz)

742Black

LS1

Boost Control

863Black

+12V

928Black

Digital_In_3

Flex Fuel Sensor (Hz)

1071Black

Analog_In_16

Mode Switch

1175Black

Analog_In_10

Baro Pressure

1274Black

Analog_In_11

Shift Switch

AUX Connector Pinout

Page 12

LAMBDA

COIL

Deutsch Pin

Infinity Pin

Default Pin Function

Deutsch Pin

Default Pin Function

18UEGO1 UN

Infinity 14

Coil 1

26UEGO1 IA

Infinity 13

Coil 2

363+12V

Infinity 12

Coil 3

45UEGO1 Heat

Infinity 11

Coil 4

59UEGO1 VM

Infinity 33

Ground

67UEGO1 IP

Honda B13

Distributor ICM

AEMNet

FLASH ENABLE

Deutsch Pin

Infinity Pin

Default Pin Function

Delphi Pin

Infinity Pin

Default Pin Function

135CAN A+

A10Permanent Power

234CAN A-

Harness Flash Enable

363+12V

433Ground

P/N 30-3509

Miscellaneous Pinouts

Honda Pin Numbering

Infinity Pin Numbering

Viewed from Wire Side

Page 13

12 MONTH LIMITED WARRANTY

Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase. Products that fail within this 12-month warranty period will be repaired or replaced at AEM’s option, when determined by AEM that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be responsible for special, incidental or consequential damages or cost incurred due to the failure of this product. Warranty claims to AEM must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12-month warranty period. Improper use or installation, accident, abuse, unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Merchandise Authorization (RMA) number. Product must be received by AEM within 30 days of the date the RMA is issued.

1999–2001 Honda B-H-D Series OBD2b

Please note that before AEM can issue an RMA for any electronic product, it is first necessary for the installer or end user to contact the EMS tech line at 1-800-423-0046 to discuss the problem. Most issues can be resolved over the phone. Under no circumstances should a system be returned or a RMA requested before the above process transpires.

AEM will not be responsible for electronic products that are installed incorrectly, installed in a non-approved application, misused, or tampered with.

Any AEM electronics product can be returned for repair if it is out of the warranty period. There is a minimum charge of $50.00 for inspection and diagnosis of AEM electronic parts. Parts used in the repair of AEM electronic components will be extra. AEM will provide an estimate of repairs and receive written or electronic authorization before repairs are made to the product.