AEM 30-2131-XXX Brass Pressure Sensor User Manual

Instruction Manual

P/N 30

-213

1-XXX

Pressure

Sensor

s

Spec

ifications:

The model 30-2131-XXX family of pressure transducers is specifically designed for pressure measurements in automotive systems. The mechanical
connection is 1/8" Male NPT. Each sensor comes with a mating connector plug and pin kit. Sensors are not recommended for use with methanol.

Kit Contents
Part Number Sensor Connector
30-2131-15G 15 Psig Included
30-2131-30 30 Psia (2 Bar) Included
30-2131-50 50 Psia (3.5 Bar) Included
30-2131-75 75 Psia (5 Bar) Included
30-2131-100 100 Psig Included
30-2131-150 150 Psig Included

Accuracy (Temp Included): < +/- 3% FS
Mounting Torque: 14.7 ft-lbf
Operating Temp: -20 to 105C
Burst Pressure: 2 X FS
Supply Voltage: 5V +/- 0.25V
Supply Current: 4.5 mA at 5VDC
Weight: < 60 Grams
Body Material: Brass
Wetted Material: 316L
Mechanical Connection: 1/8”NPT Male
Electrical Connection: Packard 3-Pin

Electrical Termination:

Signal Ground: Tap to Sensor/Signal Ground on EMS or AQ1
Sensor Power: Tap to Sensor Power +5V on EMS or AQ1
Signal: Connect to MAP/Input Channel on EMS or Input 1-8 on AQ1

AEM Performance Electronics

2205 126th Street Unit A, Hawthorne, CA. 90250

Phone: [phone] Fax: [phone]

http://www.aemelectronics.com

Instruction Part Number: 10-2131 Rev C

 2012 AEM Performance Electronics

IMPORTANT!

The terminals are “Pull to Seat” meaning you must feed the wire through the connector housing BEFORE you crimp on the terminals. The wire is then
pulled back into the housing and the terminal locks in place. The terminal cannot be inserted or removed from the rear (wire side entry) of the housing.
See Figure 1. Below

Figure 1. Connector Assembly Showing Pull to Seat Terminal

VOLTAGE OUTPUT

Voltage 30-2131-15G 30-2131-30 30-2131-50 30-2131-75 30-2131-100 30-2131-150

Range 0-15 PSIg -14.7-15.3 PSIa -14.7-35.3 PSIa -14.7-60.3 PSIa 0-100 PSIg 0-150 PSIg

0.5 0 -14.7 -14.7 -14.7 0 0

0.75 0.9 -12.825 -11.575 -10.013 6.25 9.375
1 1.9 -10.95 -8.45 -5.325 12.5 18.75

1.25 2.8 -9.075 -5.325 -0.637 18.75 28.125

1.5 3.8 -7.2 -2.2 4.05 25 37.5

1.75 4.7 -5.325 0.925 8.738 31.25 46.875
2 5.6 -3.45 4.05 13.425 37.5 56.25

2.25 6.6 -1.575 7.175 18.113 43.75 65.625

2.5 7.5 0.3 10.3 22.8 50 75

2.75 8.4 2.175 13.425 27.488 56.25 84.375
3 9.4 4.05 16.55 32.175 62.5 93.75

3.25 10.3 5.925 19.675 36.863 68.75 103.125

3.5 11.3 7.8 22.8 41.55 75 112.5

3.75 12.2 9.675 25.925 46.238 81.25 121.875
4 13.1 11.55 29.05 50.925 87.5 131.25

4.25 14.1 13.425 32.175 55.613 93.75 140.625

4.5 15.0 15.3 35.3 60.3 100 150

12 MONTH LIMITED WARRANTY

Advanced Engine Management Inc. warrants to the consumer that all AEM High Performance products will be free from defects in material and
workmanship for a period of twelve (12) months from date of the original purchase. Products that fail within this 12-month warranty period will be
repaired or replaced at AEM’s option, when determined by AEM that the product failed due to defects in material or workmanship. This warranty is
limited to the repair or replacement of the AEM part. In no event shall this warranty exceed the original purchase price of the AEM part nor shall AEM be
responsible for special, incidental or consequential damages or cost incurred due to the failure of this product. Warranty claims to AEM must be
transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non­transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Improper use or installation, accident, abuse,
unauthorized repairs or alterations voids this warranty. AEM disclaims any liability for consequential damages due to breach of any written or implied
warranty on all products manufactured by AEM. Warranty returns will only be accepted by AEM when accompanied by a valid Return Goods
Authorization (RGA) number. Product must be received by AEM within 30 days of the date the RGA is issued.
Please note that before AEM can issue an RGA for any product, it is first necessary for the installer or end user to contact the AEM Performance
Electronics tech line at 1-800-423-0046 to discuss the problem. Most issues can be resolved over the phone. Under no circumstances should a system
be returned or a RGA requested before the above process transpires.