AEG-Electrolux ZWDD 110 User Manual

LAVADORA-SECADORA

WASHER-DRYER

ZWDD 110

MANUAL DE USO

USER MANUAL

132987850

Maximum loads 30

Laundry weights 30

Removing stains 30-31

Detergents and additives 31

Drying hints 32

Load 32

Garments not suitable for drying 32

Drying symbols on garment labels 32

Duration of the drying cycle 32

Modification of the drying time 32

Fibre residue 32

Additional drying 32

International wash code symbols 33

Operating sequence - Washing only 34

Washing programmes 35-36

Drying programmes 37

Operating sequence - Drying 37

Maintenance 38

Bodywork 38

Detergent dispenser drawer 38

Drain filter 38

Water inlet filter 38

Emergency emptying out 39

Frost precautions 39

Something not working? 40-41

Warnings 23

Disposal 24

Tips for environmental protection 24

Technical specifications 24

Installation 25

Unpacking 25

Positioning 25

Water inlet 25-26

Water drainage 26

Electrical connection 26

Door reversal 27

Your new washer-dryer 28

Description of the appliance 28

Use 29

Control panel 29

Controls 29

Washing hints 30

Sorting the laundry 30

Temperatures 30

Before loading the laundry 30

Contents

Dear customer,

Please read these operating instructions carefully and pay particular attention to the safety notes indicated in the first pages. We recommend that you keep this instruction booklet for future reference and pass it on to any future owners.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use recycled paper.

Transport damages

When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the Service Centre.

ENGLISH

Installation

• All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protective transit devices are not removed or are not completely removed. Refer to the relevant paragraph in the instruction book.

• Any electrical work required to install this appliance must be carried out by a qualified electrician.

• Any plumbing work required to install this appliance must be carried out by a qualified plumber.

• After having installed the machine, check that it is not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor, ensure that air can circulate freely between the feet and the floor.

Use

• This appliance is designed for domestic use. It must not be used for purposes other than those for which it was designed.

• Only wash and dry fabrics which are designed to be machine washed and dried. Follow the instructions on each garment label.

• Do not overload the appliance. Follow the instructions in the instruction book.

• Make sure that all pockets are empty. Objects such as coins, safety pins, pins and screws can cause extensive damage.

• Do not machine wash garments saturated with petroleum, methylated spirits, trichlorethylene, etc. If such fluids have been used to remove stains prior to washing, wait until they have completely evaporated from the fabric before placing garments in the appliance.

• Place small items such as socks, belts, etc. in a cloth bag or pillowcase to prevent them getting trapped between the drum and the tub.

• Use only the recommended quantities of fabric softener. An excessive amount could damage the laundry.

• If you use a liquid detergent with a dispenser which has to be placed directly in the drum, remember to remove this dispenser before drying.

Warnings

• Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and prevents the formation of musty smells.

• Always check that water has emptied out before opening the door. If not, drain the water following the instructions in the instruction book.

• Always unplug the appliance and shut the water tap after use.

General safety

• Repairs to the machine must be carried out only by qualified personnel. Repairs carried out by inexperienced persons could cause serious danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself.

• During high temperature wash programmes and during the drying cycle the door glass may get hot. Do not touch it!

Child safety

• Children are often not aware of how dangerous electrical appliances can be. When the machine is working, children should be carefully supervised and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film, polystyrene) can be dangerous to children danger of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s reach.

• Make sure that children or pets do not climb into the drum.

• When the appliance is to be scrapped, cut off the electrical supply cable and destroy the plug with the remaining cable. Disable the door catch in order to prevent children from becoming trapped inside while playing.

The following warnings are provided in the interests of overall safety. You must read them carefully before installing or using the appliance.

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are recyclable.

>PE<=polyethylene >PS<=polystyrene >PP<=polypropylene

This means that they can be recycled by disposing of them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance. Help to keep your country tidy!

The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

To save water, energy and to help protect the environment, we recommend that you follow these tips:

• Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).

• The machine works more economically if it is fully loaded (for both washing and drying cycles).

• The machine will consume less energy if the

laundry is adequately spun before being dried.

• With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed at a lower temperature.

• Measure out detergent according to the water hardness, the degree of soiling and the quantity of laundry being washed.

DIMENSIONS Height 85 cm

Width 60 cm Depth 60 cm

WASHING DRYING

MAXIMUM LOAD Cotton 5 kg 2.5 kg

Synthetics 2.5 kg 2 kg Delicates 2.5 kg Woollens 2 kg

SPIN SPEED 1000 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz TOTAL POWER ABSORBED 2200 W MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 0.05 MPa

Maximum 0.8 MPa

This appliance complies with the following EEC Directives: 73/23/EEC of 19/02/73 relating to low voltage 89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

ENGLISH

Unpacking

All transit bolts and packing must be removed before using the appliance.

You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again.

1. Using a spanner, unscrew and remove the two rear bottom screws. Slide out the two plastic pins. Lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor.

2. Remove the polystyrene block from the bottom of the machine and release the two plastic bags.

3. Very carefully slide out the left polythene bag, removing it towards the right and then downwards.

4. Very carefully slide out the right polythene bag, removing it towards the left and then upwards.

5. Set the machine upright and remove the remaining rear screw. Slide out the relevant pin.

P1127

P1126

P1124

P0001

P1129

6. Plug all the holes with the plugs which you will find in the envelope containing the instruction booklet.

Positioning

Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Check that the machine does not touch the wall or other kitchen units. Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor.

Water inlet

Connect the water inlet hose supplied with the machine to a tap with a 3/4" thread.

Do not use already employed hoses.

The other end of the inlet hose which connects to the machine can be turned in any direction. Simply loosen the fitting, rotate the hose and retighten the fitting, making sure there are no water leaks.

P0021

P1088

P1051

P0002

P1128

Installation

The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use.

Important!

Before connecting up the machine to new pipework or to pipework that has not been used for some time, run off a reasonable amount of water to flush out any debris that may have collected in the pipes.

Water drainage

The end of the drain hose can be positioned in three ways:

Hooked over the edge of a sink using the plastic hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be above the trap so that the bend is at least 60 cm above the ground.

Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm. The end of the drain hose must always be ventilated, i.e. the inside diameter of the drain pipe must be larger than the outside diameter of the drain hose.

P0022

The drain hose must not be kinked. Run it along the floor; only the part near the drainage point must be raised.

Electrical connection

This machine is designed to operate on a 220-230 V, single-phase, 50 Hz supply.

Check that your domestic electrical installation can take the maximum load required (2.2 kW), also taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precaution. Should the appliance power supply cable need to be replaced, this should be carried out by our Service Centre.

Important! When the appliance is installed the power supply

cable must be easily accessible.

P0023

ENGLISH

Door reversal

The opening direction of the outer door on this machine can be reversed. To carry out this operation, proceed as follows:

1) Disengage the end of the opening stop (1) from the door and turn it through 90° to remove it from its seat (Fig. A).

2) Using a screwdriver, turn plastic plug (2) through 90° to remove it from its seat (Fig. A).

3) Fit plug (2) in the hole left free by opening stop (1 ) and turn it through 90° to lock it into place (Fig. B).

4) Fit opening stop (1) into the hole from which plug (2) was removed and turn it through 90°, making sure that the latching tooth is facing towards the right (Fig. B).

5) Remove the door by unscrewing the screws securing it to the bottom hinge (3 - Fig. A).

6) Unscrew the two plastic screws (4 - Fig. A) and fit them on the opposite side (4 - Fig. B).

7) Remove the catch hook (5 - Fig. A) by inserting a screwdriver into the upper hole and pushing downwards.

8) Remove plate (6) by inserting a screwdriver into the bottom hole and pushing upwards (Fig. A).

9) Refit the catch hook (5) and plate (6) on the opposite sides.(Fig. B).

10) Remove the door catch (7) and plate (8) as explained in paragraph 7.

11) Turn the door through 180°.

12) Refit the door catch (7) and plate (8), reversing their position and pressing firmly to engage the hook (Fig. B).

13) Fit the door onto the washing machine. Insert the top pin first, then the bottom pin into the hinge (3 - Fig. B); finally screw the hinge onto the washing machine.

14) Check that the door is aligned with the appliance. To do this, loosen screw (9 - Fig. B) by a couple of turns and re-tighten when alignment is correct.

15) Fit the flexible end of the door opening stop into the location provided in the door (1 - Fig. B).

Fitting a door panel

The door of this machine has mouldings to allow fitting of a decorative panel (stainless steel sheet, laminated plastic, wood, etc.) to match with the existing kitchen units.

The dimensions of the panel must be as follows:

Width 588 mm

Height 588 mm

Maximum thickness 4 mm

To fit the panel, remove the moulding by unscrewing its fixing screws. Position the panel, then refit the moulding, making sure that it comes into contact with and firmly clamps the panel.

P0535

P0534

391

+ 15 hidden pages