AEG-Electrolux S71340KA8 User Manual

SANTO 71340-8 KA
User manual Manual de instruções
Fridge
Refrigerador
2
Dear Customer
tional design and cutting edge technology. Convince yourself that our appliances are engineered to deliver the best
performance and control - indeed we are setting the highest standards of excellence.
In addition to this you find environmental and energy saving aspects as an integral part of our products.
To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are used in this manual
Important information concerning your personal safety and information on
how to avoid damaging the appliance
General information and tips
Environmental information
3
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Your appliance needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Rear spacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Rehingeing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Prior to Inital Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Starting up - setting the temperature . . . . . . . . . . . . . . . . . . . . . . .10
Cold Store compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Air recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Interior Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Storage shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Door rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Bottle holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Fresh food refrigeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . .18
4
Safety
The safety aspects of our refrigerators/freezers comply with accepted techni­cal standards and the German Appliance Safety Law. Nevertheless, we consi­der it our obligation to make you aware of the following safety information:
Intended use
• The refrigerator is intended for use in the home. It is suitable for the coo­ling food. If the appliance is used for purposes other than those intended or used incorrectly, no liability can be accepted by the manufacturer for any damage that may be caused.
• Alterations or changes to the freezer are not permitted for reasons of safety.
• If you use the refrigerator in a commercial application or forpurposes other than the cooling of foods, please observe all valid legal regulations for your application.
Prior to initial start–up
• Check the refrigerator for transport damage. Under no circumstance
should a damaged appliance be plugged in! In the event of damage, please contact the vendor.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compa­tibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition; – thoroughly ventilate the room in which the appliance is situated.
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children. There is a risk of suffocation! Keep packaging material away from children!
• Please make old appliances unusable prior to disposal. Pull out the mains plug, cut off the mains cable, break or remove spring or boltcatches, if fit­ted. By doing this you ensure that children cannot lock themselves in the fridge when playing (there is risk of suffocation!)or get themselves into other dangerous situations.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction con­cerning use of the appliance by a person responsible for their safety.
5
Children should be supervised to ensure that they do not play with the appliance. !
Daily Operation
• Do not operate any electrical appliances in the refrigerator/freezer (e.g. electric ice cream makers, mixers etc.).
• Before cleaning the appliance, always switch off the appliance and unplug it, or pull the house fuse or switch off the circuit breaker.
• When unplugging always pull the plug from the mains socket, do not pull on the cable.
In case of malfunction
• If the a malfunction occurs on the appliance, please look first in the "What to do if ..." section of these instructions. If the information given there does not help, please do not perform any further repairs yourself.
• Refrigerators/freezers may only be repaired by qualified service engineers. Improper repairs can give rise to significant hazards. If your appliance needs repairing, please contact your specialist dealer or our Customer Service.
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be dumped or burned at an incinerating plant without danger! About the materials: The plastics can be recycled and are identified as fol­lows: >PE< for polyethylene, e.g. the outer covering and the bags in the interior. >PS< for polystyrene foam, e.g. the pads, which are all free of chlorofluo­rocarbon.
The carton parts are made from recycled paper and should be disposed of at a waste-paper recycling collection location.
Disposal of old Appliances
For environmental reasons, refrigeration appliances must be disposed of properly. This applies to your old appliance, and - at the end of its service life - for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable. Remo­ve plug from mains, sever the power cable, remove or destroy any snap or latch closures. This eliminates the danger that playing children lock them­selves into the appliance (danger of suffocation!) or place themselves into other life-endangering situations.
Disposal:
• The appliance may not be disposed of with domestic waste or bulky refuse.
• The refrigerant circuit, especially the heat exchanger at the back of the appliance, may not be damaged.
6
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room. Energy use is affected by the ambient temperature. The appliance should
therefore – not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat; – only be installed at a location whose ambient temperature corresponds to
the climate classification, for which the appliance is designed.
The climate classification can be found on the serial plate, which is located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for each climate classification: each climate classification:
• The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative con­sequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this pro­duct. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Remove transport safeguard
The appliance and the interior fittings are protected for transport.
•Remove all adhesive tape and packing pieces from the interior of the appliance.
Your appliance is equipped with shelf retainers that make it possible to secu­re the shelves during transportation.
To remove them proceed as follows: Move the shelf retainers in the direc-
tion of the arrow, raise the shelf from the rear and push it forward until it is freed and remove the retainers.
A
C
B
7
Climate classification for an ambient temperature of
SN +10 bis +32 °C
N +16 bis +32 °C
ST +18 bis +38 °C
T +18 bis +43 °C
Your appliance needs air
For safety reasons, minimum ventila­tionmust be as shown Fig.
Attention: keep ventilation ope­nings clear of obstruction;
Rear spacers
Fit the rear spacers contained in the appliance to ensure even dis­sipation of heat genereted during operation. Proceed in the sequen­ce illustrated by the figures.
100 mm10 mm
10 mm
NP007
Rehingeing the door
The side at which the door opens can be changed from the right side (fac­tory adjustment) to the left side, if the installation site requires.
Warning! When changing the side at which the door opens, the appliance may not be connected to the mains. Remove plug from the mains before hand.
Procced as follows:
To carry out the following operations, we suggest that this be made with another person that will keep a firm hold on the door of the appliance during the operations.
Gently lay the appliance on its back.
1. Remove the ventilation grille.
2. Remove the bottom hinge (A) by unscrewing the fixing screws.
3. Remove the door.
8
4. Unscrew the pin of the bottom hinge (f) and refit it on the opposite side.
5. Unscrew the pin of the upper hin­ge (d) and refit it on the opposite side.
6. Insert the door in the upper hinge and refit the upper hinges (A).
Pay attention that the border of the doors are parallel to the top border, otherwise adjust the position of the lower hinge of the door (A).
7. Remove from the ventilation grille the cover (e) and refit it on the opposite side.
8. Refit ventilation grille.
9. Unscrew the handle. Refit it on opposite side after having pierced he plugs with a punch. Cover the holes left open with the plugs con­tained in the documentation pack.
Reposition, level the appliance, wait for at least one hour and then connect it to the mains socket.
In any case you do not want to carry out the above mentioned operations, contact the nearest After Sales Service Force. The After Sales Service specialist will carry out the reversibility of the doors at your cost.
Attention:
After having reversed the opening direction of the doors check that all the screws are properly tightened and that the magnetic seal adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet. in that case, wait for the natural fitting of the gasket or accelerate this process by heating up the part involved with a normal hairdrier.
9
Electrical connection
Before initial start-up, refer to the appliance rating plate to ascertain if sup­ply voltage and current values correspond with those of the mains at the installation location.
e.g.: AC 230 ... 240 V 50 Hz or
230 ... 240 V~ 50 Hz (i.e. 230 to 240 volts alternating current, 50 Hertz) The rating plate is inside the appliance on the left. A correctly installed, earthed socket is required for the electrical supply. The
supply must have a fuse rating of at least 10 Amps. If the socket is not accessible once the appliance is built in, the electrical
installation must include suitable means of isolating the appliance from the mains (e.g. fuse, cut-out, current trip or similar with a minimum contact separation of 3 mm).
Attention: The mains connection cable may only be replaced by a skilled electrician. Please contact your dealer or our customer service department for repairs.
Prior to Initial Start–Up
• Please clean the appliance interior and all accessories prior to initial start-
up (see section: “Cleaning and Care”).
Control panel
B
C
EDF
A
A. Button ON/OFF B. Temperature setting button (for warmer temperatures) C. Temperature display D. Temperature setting button (for colder temperatures) E. COOLMATIC function " F. COOLMATIC indicator (yellow)
10
Temperature setting buttons
The temperature is adjusted using the „B“ and „E“ buttons. These buttons are connected to the temperature display.
The temperature display is switched over from the display of the ACTUAL temperature (Temperature display is illuminated) to the display of the DESI­RED temperature (Temperature display flashes) by pressing one of the two buttons, „B“ or „D“ .
Each time one of the two buttons is pressed again the DESIRED temperatu­re is adjusted by 1 °C. The DESIRED temperature must be reached within 24 hours.
If neither button is pressed, the temperature display automatically switches back after a short period (approx. 5 sec.) to the display of the ACTUAL tem­perature.
DESIRED temperature means:
The temperature that has been selected for inside the fridge. The DESIRED temperature is indicated by flashing numbers.
ACTUAL temperature means:
The temperature display indicates the current temperature inside the fridge. The ACTUAL temperature is indicated with illuminated numbers.
Temperature display
The temperature display can indicate several pieces of information.
During normal operation, the temperature currently present in the fridge (ACTUAL temperature) is displayed.
When the temperature is being adjusted a flashing display indicates the fridge temperature currently set (DESIRED temperature).
Starting Up - Setting the Temperature
1. Plug the mains plug into the mains socket.
2. Press ON/OFF button. The appliances start.
3. Press either the „B“ or „D“ button. The temperature display switches over and the DESIRED temperature currently set flashes on the temperature display.
4. Set the required temperature by pressing the „B“ or „D“ buttons (see section "Temperature setting buttons"). The temperature display will immediately show the changed setting. Each time the button is pressed the temperatu­re is adjusted by 1 °C.
From a food safety point of view +5 °C should be considered sufficiently cold for storing food in the fridge.
11
5. Once the required temperature has been set, after a short period (approx. 5 sec.) the temperature display will change and again indicate the current ACTUAL temperature inside the fridge. The display will change from flashing to continuous illumination.
Information! When the setting is changed, the compressor does not start immediately if automatic defrosting is currently taking place. As the stora­ge temperature within the fridge is reached quickly you can store food immediately after switching on.
COOLMATIC
The COOLMATIC function is suited for quick cooling of large quantities of goods in the refrigerator.
1. The COOLMATIC function is switched on by pressing the COOLMATIC but­ton. The yellow light illuminates.
The COOLMATIC function now provides for intensive cooling. A DESIRED temperature of +2 °C is automatically selected. The COOLMATIC function is ended automatically after a period of 6 hours.
2. The COOLMATIC function can be ended manually at any time by pressing the COOLMATIC button again. The yellow light goes out.
Cold Store compartment
The models equippied with this feature in the fridge part, it is indicated for a best conservation of fresh foods as fish, meat, seafood, etc. It is placed in the lower part, directly above of the vegatable conservation drawer.
Air recycling
The refrigerator compartment is equipped with a special D.A.C.(Dynamic Air Cooling) fan which can be turned on with the switch A. The green light, when on, means that the fan is working. It is suggested that the fan be used when the ambient tempera­ture exceeds 25°C . This device allows for rapid cooling of foods and a more uniform temperature in the compartment.
A
12
Interior Accessories
Storage shelves
• You should always slide one of the full size glass storage shelf into the
lowest set of guides, above the fruit and the vegetable containers, and keep it in this position.
• The height of the storage shelves
can be adjusted:
• To do this pull the storage shelf
forward until it can be swivelle­dupwards or downwards and removed.
• Please do the same in reverse to
insert the shelf at a different hei­ght.Slide the front half of the Vario storage shelf in another level to the rear. By this means you will gain space to place tall items on the storage shelf below.
Adjusting the upper door rack
• Depending on the food stored, the upper door racks can be changed to
other holders or removed. Take out the refrigerators food, press the door racks digonally upwards at their edges, reposition them, and press them back into place.
Bottle holder
Place the bottles (with the opening facing front) in the pre- positioned shelf.
If the shelf is positioned horizontally, place only closed bottles.
This bottle holder shelf can be tilted in order to store previously opened bottles.
To obtain this result, pull the shelf up so it can rotate upwards and be pla­ced on the next higher level.
D338
Loading...
+ 28 hidden pages