AEG-Electrolux F64080VIL User Manual

FAVORIT 64080 VIL

Dishwasher

Instruction book

PERFEKT IN FORM UND FUNKTION

152958 39/0en 16-02-2005 10:50 Pagina 1

2

Dear customer,

Please read this User Information carefully and keep it to refer to at a
later date.
Pass it on to any subsequent owner of the appliance.

The following symbols are used in the text:

Safety instructions

Warning! Notes that concern your personal safety.
Attention! Notes that show how to avoid damage to the appliance.

Useful tips and hints

Environmental information

Your dishwasher has the new washing system ”IMPULSE WASHING”.
With this dishwashing system the motor speed and spray pressure
are varied during the wash cycle to achieve better cleaning of the
dishes. It is for this reason that the noise level varies during the
dishwashing cycle.

152958 39/0en 16-02-2005 10:50 Pagina 2

CONTENTS

Operating instructions 4

Safety instructions 4
Disposal 6
Economical and ecological dishwashing 6
Description of the appliance 7
The control panel 8
Prior to using for the first time 12

The water softener 12
Filling with dishwasher salt 15
Rinse aid 16

In daily use 18

Loading cutlery and dishes 18
The lower basket 20
The cutlery basket 21
The upper basket 22
Adjusting the height of the upper basket 23
Use of detergent 24
Different kinds of detergent 25

Washing programmes 27
Starting a washing programme 28
Maintenance and cleaning 31

Cleaning the filters 31

What to do, when... 34

Service 37
Guarantee terms 38

Technical specifications 41

Installation instructions 42

Building-in 42
Levelling 42
Fixing to the adjacent units 42
Water supply connections 43
Water inlet hose with safety valve 44
Water outlet hose connection 45
Electrical connection 46

Hints for test centres 47

Contents

3

152958 39/0en 16-02-2005 10:50 Pagina 3

OPERATING INSTRUCTIONS

Safety instructions

The safety of AEG electrical appliances conforms to accepted rules of
technology and the Appliance Safety Act. We as manufacturers,
however, see ourselves as being obliged to familiarise you with the
following safety instructions.

It is most important that this instruction book should be retained
with the appliance for future reference. Should the appliance be
sold or transferred to another owner, or should you move house
and leave the appliance, always ensure that the book is left with
the appliance in order that the new owner can get to know the
functioning of the appliance and the relevant safety information.

This information has been provided in the interest of your safety.
You MUST read it carefully before installing or using the
appliance.

Installation

● Check your dishwasher for any transport damage. Never connect a

damaged machine. If your dishwasher is damaged, you should
contact your supplier.

● For safety reasons it is dangerous to alter the specifications or

attempt to modify this product in any way.

● Any electrical and plumbing work required to install this appliance

should be carried out by a qualified and competent person.

● Care must be taken to ensure that the appliance does not stand on

the electrical supply cable.

● The sides of the dishwasher must never be drilled to prevent

damage to hydraulic components.

Child safety

● This appliance is designed to be operated by adults.

● Children should not be allowed to tamper with the controls or play

with the product.

● Packaging parts may be dangerous for children, who could even be

suffocated! You should therefore keep all packaging well away
from children.

Operating instructions

4

152958 39/0en 16-02-2005 10:50 Pagina 4

● The water in your dishwasher is not for drinking. Detergent residues

may still be present in your machine. Keep children well away from
your dishwasher when the door is open.

● Keep all detergents in a safe place out of children’s reach.

Your dishwasher in day-to-day use

● Items that are contaminated by petrol, paint, steel or iron debris,

corrosive, acidic or alkaline chemicals must not be washed in this
dishwasher.

● Under no circumstances should you open the door whilst the

appliance is in operation, especially during the washing phase, hot
water may escape. However, if the door is opened, a safety device
ensures that the machine stops.

● Only use products (detergent, salt and rinse aid) specifically

designed for use in dishwashers.

● Long bladed knives stored in an upright position are a potential

hazard.

● Long and/or sharp items of cutlery such as carving knives must be

positioned horizontally in the upper basket.

● Ensure that the door of the dishwasher is always closed when it is

not being loaded or unloaded. In this way you will avoid anybody
tripping over the open door and hurting themeselves.

● When finishing loading or unloading close the door, as an open

door can be a hazard.

● Do not sit or stand on the open door.

● Isolate the appliance from the power supply and turn off the water

supply after use.

● This product should be serviced by an authorised service engineer,

and only genuine spare parts should be used.

● Under no circumstances should you attempt to repair the machine

yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning. Contact your local Service Force
Centre. Always insist on genuine spare parts.

Operating instructions

5

152958 39/0en 16-02-2005 10:50 Pagina 5

Disposal

Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.

Plastic parts are marked with standard international abbreviations:
>PE< for polyethylene, e.g. sheet wrapping material.

>PS< for polystyrene, e.g. padding material (always CFC-free).
>POM< for polyoxymethylene, e.g. plastic clips.

Cardboard packaging is manufactured from recycled paper and should
be deposited in the waste paper collection for recycling.

As and when you cease to use your dishwasher and withdraw it from
service, your should render it unserviceable before having it disposed of.

Warning! Children at play could lock themselves in your dishwasher or
otherwise endanger their lives. Therefore cut off the power supply
cable and make the door closing device unusable to prevent children
from being trapped inside.

For the disposing of the appliance please take it to a recycling centre
or to your dealer who may, for a small contribution to the costs,
dispose it for you.

The symbol on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it shall be
handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please
contact your local city office, your household waste disposal service or
the shop where you purchased the product.

Economical and ecological dishwashing

● Ensure that the water softener is correctly adjusted.

● Do not pre-wash under running water.

● Select the wash programme to suit the nature and degree of the

soiling on the dishes.

● Do not use more detergent, special salt and rinse aid than is

recommended in these operating instructions and by the
manufacturer of the respective product.

Operating instructions

6

152958 39/0en 16-02-2005 10:50 Pagina 6

Operating instructions

7

Description of the appliance

1. Upper basket stop

2. Water hardness switch

3. Salt container

4. Detergent dispenser

5. Control panel

6. Rating plate

7. Rinse aid dispenser

8. Filters

9. Lower spray arm

10. Upper spray arm

11. Upper basket

IN153

152958 39/0en 16-02-2005 10:50 Pagina 7

Operating instructions

8

Function buttons: in addition to the dishwashing programme

selected and the "delay start", the following functions can also be set
with the help of these buttons:

- the setting of the water softener,

- activation/deactivation of the dosage of rinse aid,

- activation/deactivation of the audible signals,

- the cancelling of a programme in progress.

Programme selection buttons: allows the selection of the desired

washing programme (see "Washing programmes" chart).

"Delay start" button: this option allows the start of the programme

to be delayed from 1 to 19 hours. The corresponding indicator light
illuminates.

The digital display indicates:

- the level of hardness to which the water softener is set,

- if the audible signals are activated/deactivated,

- if the dosage of rinse aid is activated/deactivated,

- the countdown of the delay start,

- the approximative remaining time of the running programme,

- fault codes concerning malfunction of the dishwasher.

On/Off button

Programme selection

buttons

Function buttons

Indicator lights

“Delay start”

button

1

2

3

“3 in 1” button

The control panel

Digital display

152958 39/0en 16-02-2005 10:50 Pagina 8

Operating instructions

9

Indicator lights: have the following meanings:

"3 in 1" button : This appliance is equipped with the 3 in 1

function, that allows the use of the "3 in 1" combi detergent tablets.

This function can be selected with all washing programmes.
With the selection of this function the inflow of rinse aid and salt

from each respective supply container is automatically deactivated and
also the indicator lights for salt and rinse aid are deactivated.

Select the 3 in 1 function before the set of a washing programme.
With the use of the 3 in 1 function, the cycle durations may change.

In this case, in the digital display, the indication of the running time of
the programme is automatically updated.

Once selected this function (button indicator light illuminated ) it will
remain active also for the following washing programmes, to
deactivate the function, press the button (button indicator light off).

NOTE: Once the programme is running, the 3 in 1 function can NO
longer be changed. If you want to exclude the 3 in 1 function you
have to cancel the programme setting (see chapter "Starting a washing
programme" - "To cancel a washing programme in progress") and then
deactivate the 3 in 1 function by pressing the 3 in 1 button.
In this case you have to set a washing programme again.

Salt refilling indicator light, illuminates when the salt has
run out

Rinse aid refilling indicator light, illuminates when the rinse
aid has run out

152958 39/0en 16-02-2005 10:50 Pagina 9

Operating instructions

10

NOTE: if the drying results are not satisfactory it is possible to activate
only the dosage of rinse aid.
The activation/deactivation of the dosage of rinse aid can only be
possible with the 3 in 1 fuction active.

Activation/deactivation of the dosage of rinse aid

(The dishwasher must be switched off)

When the dosage of rinse aid has been activated, also the rinse
aid indicator light on the control panel is automatically activated.

1. Press the On/Off button. All programme selection buttons indicator

lights will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated, this means that a washing programme has been set.
The programme must be cancelled: press simultaneously the
function buttons 2 and 3 for about 2 seconds, the indicator light
of the set programme button starts flashing for about 2 seconds.
After about 2 seconds the indicator lights of all the programme
selection buttons will illuminate indicating that the set programme
has been cancelled and that the machine is now in setting mode.

2. Press simultaneously function buttons 2 and 3, until the indicator
lights of the function buttons 1, 2 and 3 start flashing.

3. Press the function button 2, the indicator lights of function
buttons 1 and 3 turn off while the indicator light of the function
button 2 goes on flashing, the digital display indicates the current
setting.

4. To change the setting, press the function button 2 again, the
digital display indicates the new setting.

5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.

Rinse aid dosage deactivated
Rinse aid dosage activated

152958 39/0en 16-02-2005 10:50 Pagina 10

Operating instructions

11

Audible signals

Audible signals have been introduced to help indicate which
operations the dishwasher is performing:

- Setting of the water softener

- End of programme

- Something not working with the machine

Deactivation/activation of the audible signals

(The dishwasher must be switched off)
Factory setting: audible signals activeted

1. Press the On/Off button. All programme selection buttons indicator
lights will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated, this means that a washing programme has been set.
The programme must be cancelled: press simultaneously the
function buttons 2 and 3 for about 2 seconds, the indicator light
of the set programme button starts flashing for about 2 seconds.
After about 2 seconds the indicator lights of all the programme
selection buttons will illuminate indicating that the set programme
has been cancelled and that the machine is now in setting mode.

2. Press simultaneously function buttons 2 and 3, the indicator lights
of the function buttons 1, 2 and 3 start flashing.

3. Press the function button 3, the indicator lights of function buttons
1 and 2 turn off while the indicator light of the button 3 goes on

flashing, the digital display indicates the current setting.

4. To change the current setting, press again the function button 3,
the digital display will indicate the new setting.

5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.

Audible signals deactivated
Audible signals activated (factory set)

152958 39/0en 16-02-2005 10:50 Pagina 11

Operating instructions

12

Prior to using for the first time

Before using your dishwasher for the first time:

1. Ensure that the electrical and water connections comply with the
installation instructions

2. Remove all packaging from inside the appliance

3. Set the water softener

4. Pour 1 litre of water inside the salt container and then fill with

dishwasher salt

5. Fill the rinse aid dispenser.

The water softener

The dishwasher is equipped with a water softener designed to remove
minerals and salts from the water supply, which would have a
detrimental or adverse effect on the operation of the appliance.

The higher the content of these minerals and salts, the harder your
water is.

Water hardness is measured in equivalent scales, German degrees,
French degrees and mmol/l (millimol per litre).

The softener should be adjusted according to the hardness of the water
in your area. Your local Water Authority can advise you on the
hardness of the water in your area.

The water softener must be set in both ways: manually, using the water
hardness dial and electronically, using the function buttons on the
control panel.

Adjusting the water

hardness setting

10

9
8
7
6

10

9
8
7
6

3 3

1

no salt

necessary

1

Manually

Electronically

2

1

Number

of audible

signals

2 2

Water hardness

51 - 70
43 - 50
37 - 42
29 - 36
23 - 28

9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0

IV

11 - 14 1,9 - 2,5 II

< 4 < 0,7 I

4 - 10 0,7 - 1,8 I/II

19 - 22
15 - 18

3,3 - 3,9
2,6 - 3,2

III

5
4

5
4

Level

indicated in

the digital

display

°dH

(german
degrees)

91 - 125
76 - 90
65 - 75
51 - 64
40 - 50

19 - 25

< 7

7 - 18

33 - 39
26 - 32

°TH

(french degrees)

mmol/l

(millimol per litre,

international unit for

the hardness of water)

Range

152958 39/0en 16-02-2005 10:50 Pagina 12

Operating instructions

13

a)Setting manually

1. Open the dishwasher door.

2. Remove the lower basket from the dishwasher.

3. Turn the water hardness dial to

position 1 or 2 (see table).

4. Replace the lower basket.
The dishwasher is factory set at

position 2.

b)Setting electronically

(The dishwasher must be switched off)
NOTE: the electronic setting of the water softener is possible ONLY

with the 3 in 1 function deactivated.
The dishwasher is factory set at level 5.

1. Press the On/Off button. All programme selection buttons indicator
lights will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated, this means that a washing programme has been set.
The programme must be cancelled: press simultaneously the
function buttons 2 and 3 for about 2 seconds, the indicator light
of the set programme button starts flashing for about 2 seconds.
After about 2 seconds the indicator lights of all the programme
selection buttons will illuminate indicating that the set
programme has been cancelled and that the machine is now in
setting mode.

2. Press simultaneously function buttons 2 and 3, until the indicator
lights of the function buttons 1, 2 and 3 start flashing.

152958 39/0en 16-02-2005 10:50 Pagina 13

AA07

Operating instructionsv

14

3. Press the function button 1, the indicator lights of function
buttons 2 and 3 turn off while the indicator light of the button 1
goes on flashing, the digital display indicates the current level and
a sequence of intermittent audible signals are heard.
The current level is indicated by the number visible in the display
and the number of intermittent audible signals heard.

Example:

displayed + 5 audible signals = level 5.

4. To change the level, press button 1. Each time the button is pressed
the level changes. (For the selection of the new level see the chart).

Examples:

if the current level is 5, by pressing button 1 once, level 6 is
selected.

if the current level is 10, by pressing button 1 once, level 1 is
selected.

5. To memorise the operation, switch off the dishwasher by pressing
the On/Off button or wait about 60 seconds after which the
dishwasher will automatically return to setting mode.

152958 39/0en 16-02-2005 10:50 Pagina 14

Operating instructions

15

Filling with dishwasher salt

Only use salt specifically designed for use in dishwashers.
All other types of salt not specifically designed for use in a
dishwasher, especially table salt, will damage the water softener.
Only fill with salt just before starting one of the complete washing
programmes.
This will prevent any grains of salt or salty water, which may have
been spilt, remaining on the bottom of the machine for any period
of time, which may cause corrosion.

To fill:

1. Open the door, remove the lower basket and unscrew the cap of

the salt container by turning it anticlockwise.

2. Pour 1 litre of water inside the container (this is necessary only
before filling with salt for the first time).

3. Using the funnel provided, pour in the
salt until the container is full.

4. Replace the cap making sure that
there is no trace of salt on the screw
thread or on the gasket.

5. Replace on the cap tightly turning it
clockwise until it stops with a click.

The salt container will require topping up periodically. You are
reminded of this by the salt indicator light on the control panel which
comes on when the salt has finished.

The salt indicator light on the control panel can remain
illuminated for 2-6 hours after the salt has been replenished,
assuming the dishwasher remains switched on. If you are using
salts that take longer to dissolve then this can take longer. The
function of the machine is not affected.

Do not worry if water over flows from the unit when filling with salt,
this is quite normal.

152958 39/0en 16-02-2005 10:50 Pagina 15

SR14

LE

T

SA

U

O

Z

LT

A

S

LZ

A

S

EL

S

Operating instructions

16

Rinse aid

Rinse aid is automatically added during the last rinse, ensuring
thorough rinsing, and spot and streak free drying. The dispenser, which
is positioned inside the door, holds about 110 ml of rinse aid, which is
sufficient for 16 - 40 dishwashing programmes, depending upon the
dosage setting.

Filling with rinse aid

1. Open the container by pressing the release button (A).

2. Add the rinse aid until the container is completely full. The

maximum level for filling is indicated by “max”.

Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an absorbent cloth

to avoid excess foaming during the next wash.
Only use branded rinse aid for dishwashers. Never fill the rinse aid

dispenser with any other substances (e.g. dishwasher cleaning
agent, liquid detergent). This would damage the appliance.

152958 39/0en 16-02-2005 10:50 Pagina 16

Operating instructions

17

Adjusting the dose

According to the finish and drying results obtained, adjust the dose of
rinse aid by means of the 6 position selector (position 1 minimum
dosage, position 6 maximum dosage).

The dose is factory set in position 4.
Increase the dose if there are drops of

water or lime spots on the dishes after
washing.

Reduce it if there are sticky whitish
streaks on the dishes or a bluish film on
glassware or knife blades.

Top up the rinse aid when the indicator light on the control panel
illuminates.

152958 39/0en 16-02-2005 10:50 Pagina 17

Operating instructions

18

In daily use

• Check if it’s necessary to refill with dishwasher salt or rinse aid.

• Load cutlery and dishes into the dishwasher.

• Fill with dishwasher detergent.

• Select a wash programme suitable for the cutlery and dishes.

• Start the wash programme.

Loading cutlery and dishes

Sponges, household cloths and any object that can absorb water
may not be washed in the dishwasher.

• Before loading the dishes, you should:

- Remove large left-overs.

- Soften remnants of burnt food in pans.

• When loading the dishes and cutlery, please note:

- Dishes and cutlery must not impede the rotation of the spray arms.

- Load hollow items such as cups, glasses, pans etc, with the opening
downwards so that water cannot collect in the container or a
deep base.

- Dishes and items of cutlery must not lie inside one another, or
cover each other.

- To avoid damage to glasses, they must not touch.

- Lay small objects in the cutlery basket.

• Plastic items and pans with teflon have a tendency to retain
water drops; these items will not dry as well as porcelain and steel
items.

152958 39/0en 16-02-2005 10:50 Pagina 18

Operating instructions

19

For washing in the dishwasher the following cutlery/dishes

are not suitable:

•Cutlery with wooden, horn, china or

mother-of-pearl handles

•Plastic items that are not heat
resistant

•Older cutlery with glued parts that is
not temperature resistant

•Bonded cutlery items or dishes

•Pewter or copper items

•Lead crystal glass

•Steel items subject to rusting

•Wooden platters

•Items made from synthetic fibres

•Only wash stoneware in the dishwasher if it

is specifically marked as being dishwasher­safe by the manufacturer.

•Glazed patterns may fade if machine
washed frequently.

•Silver and aluminium parts have a tendency
to discolour during washing. Residues, e.g.
egg white, egg yolk and mustard often
cause discolouring and staining on silver.
Therefore always clean left-overs from silver
immediately, if it is not to be washed
straight after use.

•Some types of glass can become dull after a
large number of washes.

are of limited suitability:

152958 39/0en 16-02-2005 10:50 Pagina 19

Operating instructions

20

Open the door and slide out the baskets to load the dishes.

The lower basket

The lower basket is designed to take saucepans, lids, plates, salad
bowls, cutlery etc.

Serving dishes and large lids should be arranged around the edge of
the basket, ensuring that the spray arms can turn freely.

The rows of prongs on the lower basket can be easily lowered to allow
you to load pots, pans and bowls.

152958 39/0en 16-02-2005 10:50 Pagina 20

UI91

UI88

Operating instructions

21

The cutlery basket

Long bladed knives stored in an upright position are a potential
hazard.
Long and/or sharp items of cutlery such as carving knives must be
positioned horizontally in the upper basket.
Take care when loading or unloading sharp items such as knives.

Removable knife basket

Long and/or sharp items of cutlery such as carving knives must be
placed horizontally in the removable knife basket, which is positioned
at the rear of the upper basket.

Forks and spoons should be placed in the removable cutlery basket
with the handles facing downwards and the knives with their handles
facing upwards.
If the handles protrude from the bottom of the basket, obstructing the
lower spray arm, load the cutlery with the handles facing upwards.

Mix spoons with other cutlery to prevent them from sticking together.
For best results we recommend you to

use the cutlery grid provided (if the
size and dimensions of the cutlery
allow it).

152958 39/0en 16-02-2005 10:50 Pagina 21

UI53

UI71

Operating instructions

22

The upper basket

The upper basket is designed for plates (dessert plates, saucers, dinner
plates of up to 26 cm in diameter), salad bowls, cups and glasses.

Arrange items on and underneath the cup racks so that water can
reach all surfaces.

For taller items, the cup racks can be folded upwards.
Light items (plastic bowls etc.) must be loaded in the upper basket and

arranged so they do not move.

For glasses with long stems (according to the size and dimensions),
upset the glass holder to the left-hand or right-hand position.

In case you need to load dishes in the upper basket, the glass holder
must be in the right-hand position.

152958 39/0en 16-02-2005 10:50 Pagina 22

US47

US73

Operating instructions

23

In case that plates are loaded in the upper basket:

load them starting from the rear
positions of the basket; tilting them
slightly forwards and avoiding the
front positions near the door.

Before closing the door, ensure that the spray arms can rotate
freely.

Adjusting the height of the upper basket

If washing very large plates you can load them in the lower basket
after moving the upper basket to the higher position.

To move to the higher position proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards until the mechanism is engaged

and the basket is stable.

Attention!
Never lift or lower the basket on one
side only.

When the basket is in the heigher
position you will not be able to use the
cup rack(s).

The lower the basket to the original position proceed as
follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards and then allow the mechanism to

drop back down slowly, keeping hold of it.

After loading your machine always close the door, as an open door
can be a hazard.

With upper basket raised 22 cm 33 cm
With upper basket lowered 26 cm 29 cm

Maximum height of the dishes in:

upper basket lower basket

152958 39/0en 16-02-2005 10:50 Pagina 23

US71

RC08

Operating instructions

24

Use of detergent

Only use detergents specifically designed for use in dishwashers.
Using no more then the correct amount of detergent contributes

to reducing pollution.
Please observe the manufacturer’s dosing and storage

recommendations as stated on the detergent packaging.

Fill with detergent

1. If the lid is closed: press release button (1). The lid springs open.

2. Fill the detergent dispenser (2) with detergent.

The marking indicates the dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent

3. All programmes with prewash need an additional detergent dose
(5/10 g) that must be placed in the prewash detergent chamber (3).
This detergent will take effect during the prewash phase.

4. Close the lid and press until it locks in place.

152958 39/0en 16-02-2005 10:50 Pagina 24

DE19

DE22

Operating instructions

25

Different kinds of detergent

Detergent tablets

Detergent tablets of different brands dissolve at different speeds. For
this reason some detergent tablets cannot dissolve and develop their
full cleaning power during short programmes. Therefore please use
long programmes when using detergent tablets, to ensure the
complete removal of detergent residuals.

Do not place the tablets in the tub or in the cutlery basket as this
will result in poorer wash results. The tablets should be placed in
the detergent dispenser.

Concentrated detergent

Based on their chemical composition, dishwasher detergents can be
split into two basic types:

- conventional, alkaline detergents with caustic components.

- low alkaline concentrated detergents with natural enzymes.
The use of 50°C washing programmes in conjunction with

concentrated detergents reduces pollution and is good for your dishes;
these wash programmes are specially matched to the dirt-dissolving
properties of the enzymes in the concentrated detergent. For this
reason 50°C wash programmes in which concentrated detergents are
used can achieve the same results that can otherwise only be achieved
using 65°C programmes.

Combi detergents

If you are using dishwasher detergent that includes the rinse aid
function, this must be placed in the detergent compartment.
In this case the rinse aid dispenser must be empty, in order to avoid a
double dosage.
If in the rinse aid dispenser there is still rinse aid you must wait until it
has finished before using these kind of detergents.

The rinse aid indicator light will always remain illuminated when the
machine is switched on (not all dishwasher models are foreseen with
rinse aid indicator light).

Special salt for dishwasher must still be used.

152958 39/0en 16-02-2005 10:50 Pagina 25

Operating instructions

26

Use of "3 in 1" combi detergents

General advice

These products are detergents with integrated and combined
detergent/rinse-aid and salt functions.

1. Before using these products you should first check that the
water hardness in your supply is compatible with the use of
these products as per the detergent manufacturers (on the
product packaging).

2. These products should be strictly used according to the detergent

manufacturers instructions.

3. If you encounter problems when using 3 in 1 products for the first
time then please contact the detergent manufacturers care line
(the telephone number is given on the product packaging).

Special advice

When using combination 3 in 1 products, we recommend the use of
the “3 in 1” function.

If you decide to turn back to the use of the standard detergent system
we advise that you:

● Refill both the salt container and rinse aid dispenser.

● Switch the water hardness setting to the highest possible position

and run from 1 to 3 normal washing programmes without a load.

● Readjust the water hardness setting again according to the

hardness of the water in your area.

152958 39/0en 16-02-2005 10:50 Pagina 26

Operating instructions

27

Washing programmes

(1) Ideal for washing crockery and cutlery of breakfast and dinner (fresh soil).

Characterised by a short duration.
This is the perfect daily programme, made to meet the needs of a family of 4 persons who only wish
to load breakfast and dinner crockery and cutlery.

(2) Testing programme for EN 50242 (see "Hints for Test Centres). This programme, developed for the

use of detergents with enzymes, allows you to achieve, with reduced consumption of energy the
same cleaning results that would otherwise be obtained only with the 65°C programmes and
conventional detergents. To compensate the lower temperature, the duration of washing and
drying have been extended.

(3) The consumption values are intended as a guide and depends on the pressure and the temperature of

the water and also by the variations of the power supply.

"AUTOMATIC" washing programme

During the "AUTOMATIC" washing programme the amount of soil on the dishes is determined by how
cloudy the water is.
If the appliance is partially loaded and the dishes lightly soiled, the "prewash", "main wash", and "rinse"
phases of the programme are shorter and the water consumption level is lower.

If the appliance is fully loaded and the dishes heavily soiled, the "prewash"", main wash", and "rinse"
phases of the programme are longer and the water consumption level is higher.

For this reason the programme duration, water and energy consumption levels can vary within the stated
range for AUTOMATIC programme (see "Washing programmes chart").

During the "AUTOMATIC" programme the temperature of the main wash water is also automatically
adjusted between 50°C and 65°C depending on the amount of soil on the dishes.

Programme

30 MIN

1

Crockery and
cutlery

Fresh soil

30

- • - • -

0,8 9

AUTOMATIC

Crockery and
cutlery

Normal soil

92

-

115

• •

•

1/2x

• •

1,1

-

1,5

12

-

25

INTENSIVE
CARE 70°

Crockery, cutlery,
pots and pans

Heavy soil

120

-

130

• •

•

2x

• •

1,7

-

1,9

23

-

25

ECO 50°

2

Crockery and
cutlery

Normal soil

155

-

165

• • • • •

0,95

-

1,05

13

-

15

Type of

load

Degree of

soil

Consumption

values

3

Cycle

description

Pre-rinse

Main wash

Intermediate

Final rinse

Drying

Duration (minutes)

Energy (kWh)

Water (litres)

152958 39/0en 16-02-2005 10:50 Pagina 27

Operating instructions

28

Starting a washing programme

In this fully integrated appliance the controls are located on the top of
the door. When selecting a programme, the door needs to be slightly
open.

1. Check that the baskets have been loaded

correctly and that the spray arms can rotate
freely

2. Turn on the water tap

3. Press the On/Off button

All the indicator lights of the programme selection buttons
illuminate.

4. Setting and starting the programme

a)To select a programme, press the programme button of the

desired washing programme (see "Washing programmes" chart).
The corresponding indicator light remains illuminated while the

other programme buttons indicator lights turn off.
In the digital display flashes the running time (in minutes) of the
selected programme

b)To select the delay start of the programme, press the

"delay start" button until the number of the hours selected for
the delay start, followed by the letter h, will appear in the digital
display (e.g. 1h).

The start of the programme or of the countdown for the delay start
will occur only after the closure of the door, until that moment
you can modify the selection made.

Close the dishwasher door.
a)If delay start has not been set, the programme will start

automatically.

b)If delay start has been set, the countdown starts automatically

and will decrease with steps of 1 hours.
The opening of the door will not modify or interrupt the

countdown. Once the delay start has elapsed the programme
will start automatically.

152958 39/0en 16-02-2005 10:50 Pagina 28

Operating instructions

29

Once the washing programme has started, a point-shaped optical
signal appears on the floor beneath the dishwasher’s door.
This optical signal will remain illuminated for all the duration of
the washing programme.
If the appliance has been installed higher up with a furniture door
mounted flush, the optical signal will be no longer visible.

5. To interrupt or cancel a washing programme
in progress

Interrupt, or cancel a washing programme in progress
ONLY if it’s absolutely necessary

Attention! Hot steam may escape when the door is opened.
Open the door carefully.

To interrupt a washing programme in progress

Open the dishwasher door; the programme will stop.
Close the door; the programme will start from the point at which
it was interrupted.

To cancel a washing programme in progress

Open the dishwasher door.
Press simultaneously the function buttons 2 and 3 for about 2
seconds, the indicator light of the button corresponding to the
running programme starts flashing for about 2 seconds.

After about 2 seconds the indicator lights of all the programme
buttons will illuminate indicating that the running programme has
been cancelled and that the machine has returned to setting mode.

It is now possible to select and start a new washing programme.
(If a new washing programme will be selected, check that there
is detergent in the detergent dispenser).

6. To cancel a delay start in progress

Open the dishwasher door and follow the same instructions as for
"To cancel a washing programme in progress".

With the cancelling of the delay start also the set programme has
been cancelled.

Set the washing programme again.

152958 39/0en 16-02-2005 10:50 Pagina 29

Operating instructions

30

7. End of the washing programme

The dishwasher will automatically stop and an audible signal
informs you of the end of the washing programme.

When the washing programme has ended, the optical signal on
the floor beneath the dishwasher’s door will turn off. Open the
dishwasher door only when this optical signal turns off.

Open the door carefully.
In the digital display appears 0 (remaining programme time), only

in this case the programme has ended.
Switch off the dishwasher by pressing the On/Off button.
Open the door and wait a few minutes before removing the dishes;

in this way they will be cooler and the drying will be improved.

8. Unloading the dishwasher

Hot dishes are sensitive to knocks. The dishes should therefore be
allowed to cool down before removing from the appliance.

Empty the lower basket first and then the upper one; this will
avoid water dripping from the upper basket onto the dishes in the
lower one.

Water may appear on the sides and the door of the dishwasher as
the stainless steel will eventually become cooler then the dishes.

When the washing programme has finished, it is recommended
that the dishwasher is unplugged and the water tap turned off.

152958 39/0en 16-02-2005 10:50 Pagina 30

Operating instructions

31

Maintenance and cleaning

Clean the external surfaces of the machine and control panel with a
damp soft cloth. If necessary use only neutral detergents. Never use
abrasive products, scouring pads or solvent (acetone, trichloroethylene

etc....).

Ensure that the seals around the door, the detergent and rinse aid
dispensers are cleaned regularly with a damp cloth.

We recommend every 3 months to run a 65°C wash programme
without dishes using detergent.

Cleaning the filters

The filters must be checked and cleaned from time to time.
Dirty filters will degrade the washing result.

1. Open the door, remove the lower basket.

2. The dishwasher filter system comprises a coarse filter (A), a

microfilter (B) and a flat filter (C).
Unlock the filter system using the handle on the microfilter, and
remove.

3. Turn the handle about

1

/4a turn anticlockwise and remove.

152958 39/0en 16-02-2005 10:50 Pagina 31

MA36

Operating instructions

32

4. Take hold of the coarse filter (A) by the handle with the hole and
remove from the microfilter (B).

5. Clean all filters thoroughly under running water.

6. Remove the flat filter (C) from the base of the washing

compartment and clean both faces thoroughly.

7. Put the flat filter (C) back in the base of the washing compartment.

8. Place the coarse filter (A) in the microfilter (B) and press together.

9. Put the filter combination in place and lock by turning the handle

clockwise to the stop. During this process ensure that the flat filter
does not protrude above the base of the washing compartment.

Attention!

Under no circumstances may the dishwasher be used without filters.
Incorrect repositioning and fitting of the filters will produce poor
washing results.

NEVER try to remove the upper
spray arm.

If residues of soil have clogged the
holes in the upper spray arm,
remove them with a toothpick.

152958 39/0en 16-02-2005 10:50 Pagina 32

MA40

Operating instructions

33

Prolonged periods of non-operation

If you are not using the machine for any period of time you are
advised to:

1. Unplug the appliance and then turn off the water.

2. Leave the door ajar to prevent the formation of any unpleasant

smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location where the temperature is
below 0°C. If this is unavoidable, empty the machine, close the
appliance door, disconnect the water inlet pipe and empty it.

Moving the machine

If you have to move the machine (moving house etc....):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and discharge hoses.

4. Pull the machine out together with the hoses.

Avoid over tilting the machine during transportation.

152958 39/0en 16-02-2005 10:50 Pagina 33

Operating instructions

34

What to do, when...

Certain problems are due to the lack of simple maintenance or
oversights, which can be solved with the help of the instructions given
here, without calling out an engineer.

...a flashing fault code appears

The dishwasher will not start or stops during operation.
The intervention of an alarm is indicated by a sequence of intermittent
audible signals.
The point-shaped optical signal on the floor beneath the dishwasher’s
door is flashing (not visible if the appliance has been installed higher
up with a furniture door mounted flush).

Open the dishwasher door, in the digital display is visible a fault code
(see following chart).
Carry out the following suggested corrective actions.

Fault code / Malfunction
in the digital display

appears

The machine does not fill
with water

The water tap is blocked or
furred with limescale.

The water tap is turned off.
The filter (where present) in

the threaded hose fitting at
the water inlet valve is
blocked.

Clean out the sink spigot.The sink spigot is blocked.
Check the water drain

hose connection.

Clean the water tap.

Turn the water tap on.
Clean the filter in the

threaded hose fitting.

The water inlet hose has not
been correctly laid or it is
bent or squashed.

Check the water inlet hose
connection.

The water drain hose has not
been correctly laid or it is
bent or squashed.

Possible cause Solutions

in the digital display
appears

The dishwasher will not
drain

Close the water tap and
contact your local Service
Force Centre.

Anti-flood device has
activated.

in the digital display
appears

152958 39/0en 16-02-2005 10:50 Pagina 34

Operating instructions

35

...there are problems when operating the dishwasher

The programme does not
start

Use a different brand of
detergent.

The whistling is not a cause
for concern.

The dishwasher door has not
been properly closed.

Close the door.

The main plug is not plugged
in.

Insert the mains plug.

The fuse has blown in the
household fuse box.

Replace the fuse.

For dishwasher models with
delay start option:
Delay start has been selected.

If dishes are o be washed
immediately, cancel the
delay start.

There is a whistling noise
during washing

Fault Possible cause Solutions

Once the checks have been carried out, to continue the programme
press the button of the programme that was running before the
intervention of the alarm and close the door. The programme will
continue from the point at which it was interrupted. If the fault code
reappears contact your local Service Force Centre.

For other combinations of fault codes not described in the above chart
will appear, please contact your local Service Force Centre.

152958 39/0en 16-02-2005 10:50 Pagina 35

Operating instructions

36

...the wash results are not satisfactory

The dishes are not clean

● The wrong washing programme has been selected.

● The dishes were arranged in such a way as to stop water reaching all

parts of the surface. The baskets must not be overloaded.

● The spray arms do not rotate freely due to wrong arrangement of

the load.

● The filters in the base of the washing compartment are dirty or

incorrectly positioned.

● Too little or no detergent has been used.

● Where there are limescale deposits on the dishes; the salt container

is empty or the wrong level of the water softener has been selected.

● The drain hose connection is not correct.

● The salt container cap is not properly closed.

The dishes are wet and dull

● Rinse aid was not used.

● The rinse aid dispenser is empty.

There are streaks, milky spots or a bluish coating on glasses
and dishes

● Decrease rinse aid dosing.

Water drops have dried onto glasses and dishes

● Increase rinse aid dosing.

● The detergent may be the cause. Contact the detergent

manufacturer’s consumer care line.

152958 39/0en 16-02-2005 10:50 Pagina 36

Service

37

Service

If after all these checks, the problem persists, contact your local
Service Force Centre, quoting the model (Mod.), product number (PNC)
and serial number (S.N.).

This information can be found on the rating plate located on the side
of the dishwasher door (see picture).

So that you always have these numbers
at hand, we recommend you to make a
note of them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . . . .

PNC : . . . . . . . . . . . . . . . . . . . . . . . . .

S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . .

Service and spare parts

This product should be serviced by an authorised service engineer, and
only genuine spare parts should be used.
Under no circumstances should you attempt to repair the machine
yourself.
Repairs carried out by inexperienced persons may cause injury or
serious malfunctioning. Contact your local Service Force Centre.
Always insist on genuine spare parts.

152958 39/0en 16-02-2005 10:50 Pagina 37

RA07

M
o
d
.
.
.
.

.
.
.

P
.
.

r

o

d

.

N

o

.
.
.
.
.
.
.
..

S
e

r
.
N
o
.
.
.
.
.
.
.
.
.
.

Guarantee terms

38

Guarantee terms (Belgium)

Our appliances are produced with the greatest of care. However, a defect may still occur.
Our consumer services department will repair this upon request, either during or after the
guarantee period. The service life of the appliance will not, however, be reduced as a
result.

This declaration of guarantee terms is based on European Union Directive 99/44/EC and
the provisions of the Civil Code. The statutory rights that the consumer has under this
legislation are not affected by this declaration of guarantee terms.

This declaration does not affect the vendor’s statutory warranty to the end user. The
appliance is guaranteed within the context of and in adherence with the following terms:

1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free
of charge any defect that occurs within 24 months from the date the appliance is
delivered to the first end user.
These guarantee terms do not apply in the event of use for professional or equivalent
purposes.

2. Performing the guarantee means that the appliance is returned to the condition it
was in before the defect occurred. Defective parts are replaced or repaired.
Parts replaced free of charge become our property.

3. So as to avoid more severe damage, the defect must be brought to our attention
immediately.

4. Applying the guarantee is subject to the consumer providing proof of purchase
showing the purchase and/or delivery date.

5. The guarantee will not apply if damage caused to delicate parts, such as glass
(vitreous ceramic), synthetic materials and rubber, is the result of inappropriate use.

6. The guarantee cannot be called on for minor faults that do not affect the value or
the overall reliability of the appliance.

7. The statutory warranty does not apply when defects are caused by:

● a chemical or electrochemical reaction caused by water,

● abnormal environmental conditions in general,

● unsuitable operating conditions,

● contact with harsh substances.

8. The guarantee does not apply to defects due to transport which have occurred
outside of our responsibility. Nor will the guarantee cover those caused by
inadequate installation or assembly, lack of maintenance or failure to respect the
assembly instructions or directions for use.

9. Defects that result from repairs or measures carried out by people who are not
qualified or expert or defects that result from the addition of non-original
accessories or spare parts are not covered by the guarantee.

152958 39/0en 16-02-2005 10:50 Pagina 38

Guarantee terms

39

10. Appliances that are easy to transport may be delivered or sent to the consumer
services department. Home repairs are only anticipated for bulky appliances or built­in appliances.

11. If the appliances are built-in, built-under, fixed or suspended in such a way that
removing and replacing them in the place where they are fitted takes more than half
an hour, the costs that result therefrom will be charged for. Connected damage
caused by these removal and replacement operations will be the responsibility of the
user.

12. If, during the guarantee period, repairing the same defect repeatedly is not
conclusive, or if the repair costs are considered disproportionate, in agreement with
the consumer, the defective appliance may be replaced with another appliance of
the same value.
In this event, we reserve the right to ask for a financial contribution calculated
according to the length of time it has been used.

13. A repair under guarantee does not mean that the normal guarantee period will be
extended nor that a new guarantee period begins.

14. We give a twelve month guarantee for repairs, limited to the same defect.

15. Except in the event where liability is legally imposed, this declaration of guarantee

terms excludes any compensation for damage outside the appliance for which the
consumer wishes to assert his rights. In the event of legally admitted liability,
compensation will not exceed the purchase price paid for the appliance.

These guarantee terms are only valid for appliances purchased and used in Belgium. For
exported appliances, the user must first make sure that they satisfy the technical
conditions (e.g.: voltage, frequency, installation instructions, type of gas, etc.) for the
country concerned and that they can withstand the local climatic and environmental
conditions. For appliances purchased abroad, the user must first ensure that they meet
the qualifications required in Belgium. Non-essential or requested adjustments are not
covered by the guarantee and are not possible in all cases.

Our consumer services department is always at your disposal, even after the guarantee
period has expired.

152958 39/0en 16-02-2005 10:50 Pagina 39

Guarantee terms

40

Address for our consumer services department:

Electrolux Home Products Belgium

ELECTROLUX SERVICE
Bergensesteenweg, 719
1502 Lembeek

Consumer services

Telephone

02/363.04.44

Telefax

02/363.04.00
02/363.04.60

[e-mail]
[e-mail]

152958 39/0en 16-02-2005 10:50 Pagina 40

41

Operating instructions

Dimensions:

Electrical connection:

Voltage
Overall power
Fuse

Water supply pressure:

Capacity:

Width 59.6 cm
Height 86.8 - 94.8 cm
Max depth 55.5 cm
Max depth with open door 119 cm

Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher’s door.

Minimum 50 kPa (0.5 bar)
Maximum 800 kPa (8 bar)

12 place settings

This appliance complies with the following E.E.C. Directives:

- 73/23 or 19.2.73 (Low Voltage Directive) and subsequent modifications;

- 89/336 or 3.5.89 (Electromagnetic Compatibility Directive) and subsequent
modifications.

Technical specifications

152958 39/0en 16-02-2005 10:50 Pagina 41

Installation instructions

42

Installation instructions

Any electrical and/or plumbing work required to install this
appliance should be carried out by a qualified electrician and/or
plumber or competent person.

Remove all packaging before positioning the machine.
If possible, position the machine next to a water tap and a drain.

Building-in

This dishwasher is designed to be fitted under a kitchen counter or
worksurface.

Attention!

Carefully follow the instructions on the enclosed template for
building in the dishwasher and fitting the furniture panel.

No further openings for the venting of the dishwasher are required,
but only to let the water fill and drain hose and power supply cable
pass through.

The dishwasher incorporates adjustable feet to allow the adjustment of
the height.

During all operations that involve accessibility to internal components
the dishwasher has to be unplugged.

When inserting the machine, ensure that the water inlet hose, the
drain hose and the supply cable are not kinked or squashed.

Levelling

Good levelling is essential for correct closure and sealing of the door.
When the appliance is correctly levelled, the door will not catch on

either side of the cabinet.
If the door does not close correctly, loosen or tighten the adjustable

feet until the machine is perfectly level.

Fixing to the adjacent units

The dishwasher must be secured against tilting.
Therefore make sure that the counter it is fixed under, is suitably

secured to a fixed structure (adjacent kitchen units cabinets, wall).

152958 39/0en 16-02-2005 10:50 Pagina 42

Installation instructions

43

Water supply connections

This dishwasher may be fed with either hot (max. 60°) or cold water.
Nevertheless we advise you a cold water supply.
A hot water supply is not always efficient with very soiled crockery as
it shortens the washing programmes a lot.

For making the connection itself, the coupling nut fitted to the
machine’s supply hose is designed to screw onto either a 3/4" inch
gas thread spout or to a purpose made quick-coupling tap such as
the Press-block.

The water pressure must be within the limits given in the "Technical
specifications". Your local Water Authority will advise you on the
average mains pressure in your area.

The water inlet hose must not be kinked, crushed, or entangled when
it is being connected up.

The dishwasher features fill and drain hoses which can be turned
either to the left or the right to suit the installation by means of the
locknut. The locknut must be correctly fitted to avoid water leaks.
(Attention! NOT all models of dishwashers have fill and drain hoses
provided with locknut. In this case, this kind of facility is not
possible).

If the machine is connected to new pipes or pipes which have not
been used for a long time, you should run the water for a few
minutes before connecting the inlet hose.

Do not use, for connection, old hoses which have been used in
another appliance.

The dishwasher is fitted with safety devices that prevent the wash
water returning into the drinking water system and comply with the
applicable plumbing regulations.

152958 39/0en 16-02-2005 10:50 Pagina 43

Installation instructions

44

Water inlet hose with safety valve

After connecting the double-walled water inlet hose, the safety valve
is next to the tap. Therefore the water inlet hose is only under pressure
while the water is running. If the water inlet hose starts to leak during
this operation, the safety valve cuts off the running water.

Please take care when installing the water inlet hose:

- The electrical cable for the safety valve is in the double-walled
water inlet hose. Do not immerse the water inlet hose or the safety
valve in water.

- If water inlet hose or the safety valve is damaged, remove the mains
plug immediately.

- A water inlet hose with safety valve must only be replaced by a
specialist or by the consumer services department.

- Place the water inlet hose in such a way that it is never higher than
the bottom edge of the safety valve.

152958 39/0en 16-02-2005 10:50 Pagina 44

Installation instructions

45

Water outlet hose connection

The end of the drain hose can be connected in the following ways:

1. To the sink outlet spigot, securing it to the underside of the work
surface. This will prevent waste water from the sink running into the
machine.

2. Hooked over the edge of the sink using the special curved plastic
guide (if provided with the machine).

3. To a stand pipe provided with vent-hole, minimum internal
diameter 4 cm.

The waste connection must be at a height of between 30 cm
(minimum) and 100 cm (maximum) from the bottom of the
dishwasher.

The drain hose can face either to the right or left of the dishwasher
Ensure the hose is not bent or squashed as this could prevent or slow

down the discharge of water.
The sink plug must not be in place when the machine is draining as

this could cause the water to syphon back into the machine.
If you use a drain hose extension it must be no longer than 2 metres

and its internal diameter must be no smaller than the diameter of the
hose provided.

Likewise the internal diameter of the couplings used for connections
to the waste outlet must be no smaller than the diameter of the hose
provided.

Attention!

Our appliances are supplied with a security device to protect against
the return of dirty water back into the machine.
If the spigot of your sink has a "no return valve" incorporated this can
prevent the correct draining of your dishwasher.
We advise you therefore to remove it.

152958 39/0en 16-02-2005 10:50 Pagina 45

CS18

Installation instructions

46

Electrical connection

Information concerning the electrical connection is given on the
rating plate on the edge of the dishwasher’s door.

Before plugging the appliance into the wall socket, make sure that:

1. The mains voltage and current rating at the site of installation
match the nominal voltage and current rating given on the rating
plate.

2. The meter, fuses, mains power supply and wall socket can all take
the maximum load required. Make sure that the socket and plug are
compatible without having to use any type of adaptor. If necessary,
have the domestic wiring system socket replaced.

To isolate the dishwasher from mains, remove the mains plug.

Important!
The plug must still be accessible after the appliance has been
installed.

In case that the electrical cable has to be replaced, please contact
your local consumer services department.

The appliance should not be connected to the electrical supply by
means of an extension cable.

Safety standards require the appliance to be earthed.
The manufacture accepts no liability for failure to observe the
above safety precautions.

152958 39/0en 16-02-2005 10:50 Pagina 46

Hints for test centres

47

Hints for test centres

Testing in accordance with EN 60704 must be carried out with
appliance fully loaded and using the test programme (see "Washing
programmes" chart).

Test in accordance with EN 50242 must be carried out when the salt
dispenser and rinse aid container have been filled with salt and rinse
aid respectively and using the test programme (see "Washing
programmes" chart).

Load:
Rinse aid setting
Detergent dosage:

Position 4 (type III)
5 g + 25 g (type B)

12 standard place settings

Arrangement cutlery

basket

Arrangement knife basket

Cup racks: position A

Arrangement lower basket

Arrangement upper basket

(take off the glass holder)

152958 39/0en 16-02-2005 10:50 Pagina 47

AEG Hausgeräte GmbH

Postfach 1036
D-90327 Nürnberg

http://www.aeg.hausgeraete.de
© Copyright by AEG

152 958 39/0

From the Electrolux Group. The world’s No.1 choice.

The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, vacuum cleaners, chain
saws and lawn mowers) are sold each year to a value of approx. 14 billion USD in more than 150 countries
around the world.

Subject to change without notice

02/05

152958 39/0en 16-02-2005 10:50 Pagina 48