FSB42607Z
USER
MANUAL
EN User Manual
Dishwasher
www.aeg.com2
CONTENTS
1. SAFETY INFORMATION............................................................................................. 2
2. SAFETY INSTRUCTIONS.............................................................................................4
3. PRODUCT DESCRIPTION...........................................................................................6
4. CONTROL PANEL....................................................................................................... 7
5. PROGRAMME SELECTION........................................................................................ 7
6. BASIC SETTINGS ........................................................................................................9
7. BEFORE FIRST USE................................................................................................... 13
8. DAILY USE.................................................................................................................. 14
9. HINTS AND TIPS........................................................................................................16
10. CARE AND CLEANING.......................................................................................... 17
11. TROUBLESHOOTING.............................................................................................20
12. TECHNICAL INFORMATION................................................................................. 24
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler – features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website to:
Get usage advice, brochures, trouble shooter, service and repair information:
www.aeg.com/support
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
ENGLISH 3
damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
• Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
• Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
• Do not let children play with the appliance.
• Keep detergents away from children.
• Keep children and pets away from the appliance when
the door is open.
• Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
• This appliance is intended to be used in household
and similar applications such as:
– farm houses; staff kitchen areas in shops, offices
and other working environments;
– by clients in hotels, motels, bed & breakfast and
other residential type environments.
• Do not change the specification of this appliance.
• The operating water pressure (minimum and
maximum) must be between 0.5 (0.05) / 8 (0.8) bar
(MPa)
• Follow the maximum number of 13 place settings.
www.youtube.com/electrolux
www.youtube.com/aeg
How to install your 60 cm
Dishwasher Sliding Hinge
www.aeg.com4
• If the supply cord is damaged, it must be replaced by
the manufacturer, its Authorised Service Centre or
similarly qualified persons in order to avoid a hazard.
• Put the cutlery in the cutlery basket with the sharp
ends pointing down or put them in the cutlery drawer
in a horizontal position with the sharp edges down.
• Do not leave the appliance with the open door
unattended to avoid stepping accidentally onto it.
• Before any maintenance operation, deactivate the
appliance and disconnect the mains plug from the
socket.
• Do not use high pressure water sprays and/or steam
to clean the appliance.
• If the appliance has ventilation openings in the base,
they must not be covered e.g. by a carpet.
• The appliance is to be connected to the water mains
using the new supplied hose-sets. Old hose sets must
not be reused.
2. SAFETY INSTRUCTIONS
2.1 Installation
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Do not use the appliance before
installing it in the built-in structure
due to safety manner.
• Follow the installation instructions
supplied with the appliance.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Do not install or use the appliance
where the temperature is less than
0 °C.
• Install the appliance in a safe and
suitable place that meets installation
requirements.
WARNING!
Only a qualified person must
install this appliance.
2.2 Electrical connection
WARNING!
Risk of fire and electric
shock.
• The appliance must be earthed.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Always use a correctly installed
shockproof socket.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug and to the mains
cable. Should the mains cable need
ENGLISH 5
to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• This appliance is fitted with a 13 A
mains plug. If it is necessary to
change the mains plug fuse, use only
a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
2.3 Water connection
• Do not cause damage to the water
hoses.
• Before connection to new pipes,
pipes not used for a long time, where
repair work has been carried out or
new devices fitted (water meters, etc.),
let the water flow until it is clean and
clear.
• Ensure that there are no visible water
leaks during and after the first use of
the appliance.
• The water inlet hose has a safety valve
and a sheath with an inner mains
cable.
2.4 Use
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
• Dishwasher detergents are
dangerous. Follow the safety
instructions on the detergent
packaging.
• Do not drink and play with the water
in the appliance.
• Do not remove the dishes from the
appliance until the programme is
complete. Some detergent may
remain on the dishes.
• Do not store items or apply pressure
on the open door of the appliance.
• The appliance can release hot steam
if you open the door while a
programme operates.
2.5 Internal lighting
WARNING!
Risk of injury.
• Concerning the lamp(s) inside this
product and spare part lamps sold
separately: These lamps are intended
to withstand extreme physical
conditions in household appliances,
such as temperature, vibration,
humidity, or are intended to signal
information about the operational
status of the appliance. They are not
intended to be used in other
applications and are not suitable for
household room illumination.
• To replace the internal lighting,
contact the Authorised Service
Centre.
WARNING!
Dangerous voltage.
• If the water inlet hose is damaged,
immediately close the water tap and
disconnect the mains plug from the
mains socket. Contact the Authorised
Service Centre to replace the water
inlet hose.
2.6 Service
• To repair the appliance contact the
Authorised Service Centre. Use
original spare parts only.
• Please note that self-repair or nonprofessional repair can have safety
consequences and might void the
guarantee.
• The following spare parts will be
available for 7 years after the model
has been discontinued: motor,
circulation and drain pump, heaters
and heating elements, including heat
pumps, piping and related equipment
4
3
7
9
8
10
56
11
1
2
www.aeg.com6
including hoses, valves, filters and
aquastops, structural and interior
parts related to door assemblies,
printed circuit boards, electronic
displays, pressure switches,
thermostats and sensors, software
and firmware including reset software.
Please note that some of these spare
parts are only available to professional
repairers, and that not all spare parts
are relevant for all models.
• The following spare parts will be
available for 10 years after the model
has been discontinued: door hinge
and seals, other seals, spray arms,
3. PRODUCT DESCRIPTION
The graphics below is just a
general product overview.
For more detailed
information, refer to other
chapters and/or documents
provided with the appliance.
drain filters, interior racks and plastic
peripherals such as baskets and lids.
2.7 Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the
mains supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent
children and pets to get closed in the
appliance.
1
2
3
4
5
Upper spray arm
Lower spray arm
Filters
Rating plate
Salt container
Air vent
6
Rinse aid dispenser
7
Detergent dispenser
8
Cutlery basket
9
Lower basket
10
Upper basket
1 3
4 5
2
6
BA C
11
4. CONTROL PANEL
ENGLISH 7
On/Off button
1
Delay Start button
2
Indicators
3
MY TIME selection bar
4
4.1 Indicators
Indicator Description
The ECO programme indicator. It indicates the most environmentally
friendly programme selection for a normally soiled load. Refer to "Pro-
gramme selection".
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to "Before first use".
Salt indicator. It is on when the salt container needs refilling. Refer to "Be-
fore first use".
Machine Care indicator. It is on when the appliance needs internal cleaning with the Machine Care programme. Refer to "Care and cleaning".
Drying phase indicator. It is on when a programme with the drying phase
is selected. It flashes when the drying phase operates. Refer to "Pro-
gramme selection".
5. PROGRAMME SELECTION
5.1 MY TIME
Using MY TIME selection bar, you can
select a suitable wash cycle based on
programme duration, ranging from 30
minutes to four hours.
ExtraPower button
5
AUTO Sense button
6
www.aeg.com8
A. 30min is the shortest programme
suitable for washing a load with fresh
and light soil.
B. 90min is a programme suitable for
washing and drying normally soiled
items.
C. ECO is the longest programme (4h)
offering the most efficient use of
energy and water consumption for
crockery and cutlery with normal soil.
This is the standard programme for
test institutes.
1)
5.2 ExtraPower
ExtraPower improves the washing
option increases the wash temperature
and duration.
The ExtraPower option is applicable to
the following programmes: 30min, 90min
and ECO.
5.3 AUTO Sense
The AUTO Sense program automatically
adjusts the wash cycle to the type of
load.
The appliance senses the degree of soil
and the amount of dishes in the baskets.
It adjusts the temperature and quantity
of water as well as the wash duration.
results of the selected programme. The
5.4 Programmes overview
Programme Type of load Degree of soil Programme phases
30min • Crockery
• Cutlery
90min • Crockery
• Cutlery
• Pots
• Pans
ECO • Crockery
• Cutlery
• Pots
• Pans
AUTO Sense • Crockery
• Cutlery
• Pots
• Pans
• Fresh • Wash 50 °C
• Intermediate
rinse
• Final rinse 45 °C
• AirDry
• Normal
• Lightly dried-on
• Normal
• Lightly dried-on
The programme adjusts to all degrees of
soil.
• Wash 60 °C
• Intermediate
rinse
• Final rinse 55 °C
• Drying
• AirDry
• Prewash
• Wash 50 °C
• Intermediate
rinse
• Final rinse 55 °C
• Drying
• AirDry
• Prewash
• Wash 50 - 60 °C
• Intermediate
rinse
• Final rinse 60 °C
• Drying
• AirDry
1)
This programme is used to assess compliance with the Ecodesign Comission Regulation (EU)
2019/2022.
ENGLISH 9
Programme Type of load Degree of soil Programme phases
Machine Care • No load The programme
cleans the appliance
interior.
• Wash 70 °C
• Intermediate
rinse
• Final rinse
• AirDry
Consumption values
Programme
30min 9.4 -11.4 0.57 - 0.69 30
90min 9.1 - 11.1 1.01 - 1.13 90
ECO 9.9
AUTO Sense 8.2 - 11.2 0.67 - 1.08 120 - 170
Machine Care 8.4 - 10.2 0.60 - 0.71 60
1)
The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.
2)
In accordance with the 1016/2010 regulation
3)
In accordance with the 2019/2022 regulation
1)
Information for test institutes
To receive the necessary information for
conducting performance tests (e.g.
according to EN60436), send an email to:
info.test@dishwasher-production.com
In your request please include the
product number code (PNC) found on
the rating plate.
6. BASIC SETTINGS
You can configure the appliance by
changing basic settings according to
your needs.
Water (l) Energy (kWh) Duration (min)
0.9212)/0.936
3)
2402)/240
3)
For any other questions regarding your
dishwasher please refer to the service
book provided with your appliance.
Number Settings Values
1 Water hardness From level 1 to
level 10 (default:
5)
2 Rinse aid empty
notification
On (default)
Off
Description
Adjust the level of the water softener according to the water hardness in your area.
Activate or deactivate the rinse aid indicator.
1)
1 3 2
4 5
www.aeg.com10
Number Settings Values
3 End sound On
Off (default)
4 Auto door open On (default)
Off
5 Key tones On (default)
Off
1)
For more details, refer to the information provided in this chapter.
Description
Activate or deactivate the acoustic signal
for the end of a programme.
Activate or deactivate the AirDry.
Activate or deactivate the sound of the
buttons when pressed.
You can change the basic settings in
setting mode.
When the appliance is in setting mode,
the indicators on the control panel
represent available settings. For each
setting, a dedicated indicator flashes:
Water hardness
German de-
grees (°dH)
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1)
Factory setting.
2)
Do not use salt at this level.
French degrees
(°fH)
mmol/l Clarke de-
1)
6.1 The water softener
The water softener removes minerals
from the water supply, which would have
a negative effect on the washing results
and on the appliance.
The higher the content of these minerals,
the harder your water is. Water hardness
is measured in equivalent scales.
The water softener should be adjusted
according to the hardness of the water in
your area. Your local water authority can
advise you on the hardness of the water
in your area. It is important to set the
right level of the water softener to assure
good washing results.
Water softener lev-
grees
el
1)
5
2)
1
ENGLISH 11
Regardless of the type of detergent
used, set the proper water hardness
level to keep the salt refill indicator
active.
Multi-tabs containing salt are
not effective enough to
soften hard water.
Regeneration process
For the correct water softener operation,
the resin of the softener device needs to
be regenerated regularly. This process is
automatic and is the part of the normal
dishwasher operation.
When the prescribed quantity of water
(see values in the table) has been used
since the previous regeneration process,
a new regeneration process will be
initiated between the final rinse and the
programme end.
Water softener lev-elAmount of water
(l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
9 3
10 3
In case of the high water softener setting,
it may occur also in the middle of the
programme, before the rinse (twice
during a programme). Regeneration
initiation has no impact on the cycle
duration, unless it occurs in the middle of
a programme or at the end of a
programme with a short drying phase. In
that cases, the regeneration prolongs the
total duration of a programme by
additional 5 minutes.
Subsequently, the rinsing of the water
softener that lasts 5 minutes may begin
in the same cycle or at the beginning of
the next programme. This activity
increases the total water consumption of
a programme by additional 4 litres and
the total energy consumption of a
programme by additional 2 Wh. The
rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible
more than one in the same cycle) may
prolong the programme duration by
another 5 minutes when it occurs at any
point at the beginning or in the middle
of a programme.
All the consumption values
mentioned in this section are
determined in accordance
with the currently applicable
standard in laboratory
conditions with water
hardness 2.5mmol/L
according to the 2019/2022
regulation (water softener:
level 3).
The pressure and the
temperature of water as well
as the variations of the mains
supply can change the
values.
6.2 The rinse aid empty
notification
The rinse aid helps to dry the dishes
without streaks and stains. It is
automatically released during the hot
rinse phase.
When the rinse aid chamber is empty,
the rinse aid indicator is turned on
notifying to refill rinse aid. If the drying
results are satisfactory while using multitablets only, it is possible to deactivate
the notification for refilling rinse aid.
However, for best drying performance,
always use rinse aid.
If standard detergent or multi-tablets
without rinse aid are used, activate the
notification to keep the rinse aid refill
indicator active.
BA C
www.aeg.com12
6.3 End sound
You can activate an acoustic signal that
sounds when the programme is
completed.
Acoustic signals sound also
when a malfunction of the
appliance occurs. It is not
possible to deactivate these
signals.
6.4 AirDry
AirDry improves the drying results. The
appliance door opens automatically
during the drying phase and remains ajar.
AirDry is automatically activated with all
programmes.
CAUTION!
Do not try to close the
appliance door within 2
minutes after automatic
opening. This can cause
damage to the appliance.
CAUTION!
If children have access to the
appliance, we advise to
deactivate AirDry. The
automatic opening of the
door may pose a danger.
6.5 Key tones
The buttons on the control panel make a
click sound when you press them. You
can deactivate this sound.
6.6 Setting mode
How to enter setting mode
You can enter setting mode before
starting a programme. You cannot enter
setting mode while the programme is
running.
To enter setting mode, press and hold
simultaneously
about 3 seconds.
• The light related to and the
indicator flash.
• The indicators
are on.
• The lights related to MY TIME
selection bar are on.
and for
, , and
How to navigate in setting mode
You can navigate in setting mode using
MY TIME selection bar.
A. Previous button
B. OK button
C. Next button
Use Previous and Next to switch
between the basic settings and to
change their value.
Use OK to enter the selected setting and
to confirm changing its value.
How to change a setting
Make sure the appliance is in setting
mode.
1. Press Previous or Next until the
indicator dedicated to the desired
setting flashes.
The light related to indicates the
current setting value:
ENGLISH 13
• For the settings with two values
(on and off), the light is either on
(= the setting is on) or off (= the
setting is off).
• For the settings with multiple
values (levels), the light flashes.
The number of flashes indicates
the current setting value (e.g. 5
flashes + pause + 5 flashes... =
level 5).
2. Press OK to enter the setting.
• The indicator related to the
setting is on.
• The other indicators are off.
• The light related to
the current setting value.
7. BEFORE FIRST USE
1. Make sure that the current level of
the water softener agrees with the
hardness of the water supply. If
not, adjust the level of the water
softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start the programme 30min to
remove any residuals from the
manufacturing process. Do not use
detergent and do not put dishes in
the baskets.
After starting the programme, the
appliance recharges the resin in the
water softener for up to 5 minutes. The
washing phase starts only after this
procedure is complete. The procedure is
repeated periodically.
7.1 The salt container
3. Press Previous or Next to change
the value.
4. Press OK to confirm the setting.
• The new setting is saved.
• The appliance returns to the
setting selection.
5. Press and hold simultaneously
and for about 3
seconds to exit setting mode.
The appliance returns to the programme
selection.
The saved settings remain valid until you
change them again.
indicates
2. Put 1 litre of water in the salt
container (only for the first time).
3. Fill the salt container with 1 kg of salt
(until it is full).
4. Carefully shake the funnel by its
handle to get the last granules
inside.
5. Remove the salt around the opening
of the salt container.
CAUTION!
Use rough salt designed for
dishwashers only. Fine salt
increases the risk of
corrosion.
The salt is used to recharge the resin in
the water softener and to assure good
washing results in daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
6. Turn the cap of the salt container
clockwise to close the salt container.
M
A
X
1
2
3
4
+
-
A B
D
C
B
C
A
www.aeg.com14
7.2 How to fill the rinse aid
dispenser
8. DAILY USE
1. Open the water tap.
2. Press and hold
is activated.
3. Fill the salt container if it is empty.
4. Fill the rinse aid dispenser if it is
empty.
5. Load the baskets.
6. Add the detergent.
7. Select and start a programme.
8. Close the water tap when the
programme is complete.
8.1 Using the detergent
CAUTION!
Water and salt can come out
of the salt container when
you fill it. After you fill the
salt container, immediately
start a programme to
prevent corrosion.
until the appliance
CAUTION!
Only use rinse aid designed
specifically for dishwashers.
1. Press the release button (D) to open
the lid (C).
2. Pour the rinse aid in the dispenser (A)
until the liquid reaches the fill level
'max'.
3. Remove the spilled rinse aid with an
absorbent cloth to prevent excessive
foam formation.
4. Close the lid. Make sure that the
release button locks into position.
You can turn the selector of
the released quantity (B)
between position 1 (lowest
quantity) and position 4 or 6
(highest quantity).
1. Press the release button (B) to open
the lid (C).
2. Put the detergent, in powder or
tablets, in the compartment (A).
3. If the programme has a prewash
phase, put a small quantity of
detergent on the inner part of the
appliance door.
4. Close the lid. Make sure that the
release button locks into position.
8.2 How to select and start a
programme using MY TIME
selection bar
1. Press the button dedicated to the
programme you want to select.
The light related to the button is on.
2. Activate ExtraPower if desired.
3. Close the appliance door to start the
programme.
8.3 How to activate
ExtraPower
1. Select a programme using MY TIME
selection bar.
ENGLISH 15
2. Press .
The light related to the button is on.
ExtraPower is not a
permanent option and must
be activated every time
before you start a
programme.
It is not possible to activate
or deactivate ExtraPower
while a programme is
running.
Activating ExtraPower
increases the water and
energy consumption as well
as the programme duration.
8.4 How to start the AUTO Sense program
1. Press .
The light related to the button is on.
MY TIME and ExtraPower
are not applicable to this
program.
2. Close the appliance door to start the
program.
The appliance senses the type of load
and adjusts a suitable wash cycle and its
duration.
8.5 How to delay the start of a
programme
You can delay the start of the selected
programme by 3 hours.
1. Select a programme.
2. Press .
The light related to the button is on.
3. Close the appliance door to start the
countdown.
During the countdown, it is not possible
to change the programme selection.
When the countdown is complete, the
programme starts.
8.6 How to cancel the delay
start while the countdown
operates
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
If you cancel the delay start,
you have to select the
programme again.
8.7 How to cancel a running programme
Press and hold for about 3 seconds.
The appliance returns to the programme
selection.
Make sure that there is
detergent in the detergent
dispenser before you start a
new programme.
8.8 Opening the door while the appliance operates
Opening the door while a programme is
running stops the appliance. It may affect
the energy consumption and the
programme duration. After closing the
door, the appliance continues from the
point of interruption.
If the door is opened for
more than 30 seconds
during the drying phase, the
running programme ends. It
does not happen if the door
is opened by AirDry
function.
8.9 The Auto Off function
This function saves energy by switching
the appliance off when it is not
operating.
The function comes into operation
automatically:
• When the programme is completed.
• After 5 minutes if a programme was
not started.
8.10 End of the programme
When the programme is complete, the
Auto Off function switches the appliance
off automatically.
www.aeg.com16
All buttons are inactive except for the
on/off button.
9. HINTS AND TIPS
9.1 General
Follow the hints below to ensure optimal
cleaning and drying results in daily use
and to protect the environment.
• Washing dishes in the dishwasher as
instructed in the user manual usually
consumes less water and energy than
washing dishes by hand.
• Load the dishwasher to its full
capacity to save water and energy. For
best cleaning results, arrange items in
the baskets as instructed in the user
manual and do not overload the
baskets.
• Do not pre-rinse dishes by hand. It
increases the water and energy
consumption. When needed, select a
programme with a prewash phase.
• Remove larger residues of food from
the dishes and empty cups and
glasses before putting them inside
the appliance.
• Soak or slightly scour cookware with
firmly cooked-on or baked-on food
before washing it in the appliance.
• Make sure that items in the baskets
do not touch or cover each other.
Only then can the water completely
reach and wash the dishes.
• You can use dishwasher detergent,
rinse aid and salt separately or you
can use the multi-tablets (e.g. ''All in
1''). Follow the instructions on the
packaging.
• Select a programme according to the
type of load and the degree of soil.
ECO offers the most efficient use of
water and energy consumption.
• To prevent limescale buildup inside
the appliance:
– Refill the salt container whenever
necessary.
– Use the recommended dosage of
the detergent and rinse aid.
– Make sure that the current level of
the water softener agrees with the
hardness of the water supply.
– Follow the instructions in the
chapter "Care and cleaning".
9.2 Using salt, rinse aid and detergent
• Only use salt, rinse aid and detergent
designed for dishwasher. Other
products can cause damage to the
appliance.
• In areas with hard and very hard water,
we recommend to use basic
dishwasher detergent (powder, gel,
tablets containing no additional
agents), rinse aid and salt separately
for optimal cleaning and drying
results.
• Detergent tablets do not fully dissolve
with short programmes. To prevent
detergent residues on the tableware,
we recommend that you use tablets
with long programmes.
• Always use the correct quantity of
detergent. Insufficient dosage of
detergent can result in poor cleaning
results and hard-water filming or
spotting on the items. Using too
much detergent with soft or softened
water results in detergent residues on
the dishes. Adjust the amount of
detergent based on the water
hardness. Refer to the instructions on
the detergent packaging.
• Always use the correct quantity of
rinse aid. Insufficient dosage of rinse
aid decreases the drying results.
Using too much rinse aid results in
bluish layers on the items.
• Make sure that the water softener
level is correct. If the level is too high,
the increased quantity of salt in the
water might result in rust on cutlery.
9.3 What to do if you want to
stop using multi-tablets
Before you start using separately
detergent, salt and rinse aid, complete
the following steps:
1. Set the highest level of the water
softener.
2. Make sure that the salt and rinse aid
containers are full.
ENGLISH 17
3. Start the 30min programme. Do not
add detergent and do not put dishes
in the baskets.
4. When the programme is completed,
adjust the water softener according
to the water hardness in your area.
5. Adjust the released quantity of rinse
aid.
9.4 Before starting a
programme
Before you start the selected
programme, make sure that:
• The filters are clean and correctly
installed.
• The cap of the salt container is tight.
• The spray arms are not clogged.
• There is enough salt and rinse aid
(unless you use multi-tablets).
• The arrangement of the items in the
baskets is correct.
• The programme is suitable to the type
of load and the degree of soil.
• The correct quantity of detergent is
used.
9.5 Loading the baskets
• Always use the whole space of the
baskets.
• Use the appliance to wash
dishwasher-safe items only.
• Do not wash in the appliance items
made of wood, horn, aluminium,
pewter and copper as they could
crack, warp, get discoloured or pitted.
• Do not wash in the appliance items
that can absorb water (sponges,
household cloths).
• Put hollow items (cups, glasses and
pans) with the opening facing
downwards.
• Make sure that glasses do not touch
each other.
• Put light items in the upper basket.
Make sure that the items do not move
freely.
• Put cutlery and small items in the
cutlery basket.
• Make sure that the spray arms can
move freely before you start a
programme.
9.6 Unloading the baskets
1. Let the tableware cool down before
you remove it from the appliance.
Hot items can be easily damaged.
2. First remove items from the lower
basket, then from the upper basket.
After the programme is
completed, water can still
remain on the inside
surfaces of the appliance.
10. CARE AND CLEANING
WARNING!
Before any maintenance
other than running the
programme Machine Care,
deactivate the appliance and
disconnect the mains plug
from the main socket.
Dirty filters and clogged
spray arms negatively affect
the washing results. Check
these elements regularly
and, if necessary, clean
them.
10.1 Machine Care
Machine Care is a programme designed
to clean the appliance interior with
optimal results. It removes limescale and
grease buildup.
When the appliance senses the need for
cleaning, the indicator
Machine Care programme to clean the
appliance interior.
is on. Start the
How to start the Machine Care programme
Before starting the Machine
Care programme, clean the
filters and spray arms.
1. Use a descaler or a cleaning product
designed specifically for dishwashers.
Follow the instructions on the
packaging. Do not put dishes in the
baskets.
C
B
A
www.aeg.com18
2. Press and hold simultaneously
and for about 3 seconds.
The indicators and flash.
3. Close the appliance door to start the
programme.
When the programme is complete, the
indicator
is off.
10.5 Cleaning the filters
The filter system is made of 3 parts.
10.2 Internal cleaning
• Carefully clean the appliance,
including the rubber gasket of the
door, with a soft damp cloth.
• Do not use abrasive products,
abrasive cleaning pads, sharp tools,
strong chemicals, scourer or solvents.
• To maintain the performance of your
appliance, use a cleaning product
designed specifically for dishwashers
at least once every two months.
Carefully follow the instructions on the
packaging of the product.
• For optimal cleaning results, start the
Machine Care programme.
1. Turn the filter (B) counterclockwise
and remove it.
10.3 Removal of foreign objects
Check the filters and the sump after each
use of the dishwasher. Foreign objects
(e.g. pieces of glass, plastic, bones or
toothpicks, etc) decrease the cleaning
performance and can cause damage to
the drain pump.
1. Disassemble the filters system as
instructed in this chapter.
2. Remove any foreign objects by hand.
2. Remove the filter (C) out of filter (B).
CAUTION!
If unable to remove the
objects, contact an
Authorised Service
Centre.
3. Reassemble the filters as instructed
in this chapter.
3. Remove the flat filter (A).
10.4 External cleaning
• Clean the appliance with a moist soft
cloth.
• Only use neutral detergents.
• Do not use abrasive products,
abrasive cleaning pads or solvents.
4. Wash the filters.
5. Make sure that there are no residues
of food or soil in or around the edge
of the sump.
6. Put back in place the flat filter (A).
Make sure that it is correctly
positioned under the 2 guides.
ENGLISH 19
10.6 Cleaning the lower spray
arm
We recommend to clean the lower spray
arm regularly to prevent soil from
clogging the holes.
Clogged holes can cause unsatisfactory
washing results.
1. To remove the lower spray arm, pull it
upwards.
2. Wash the spray arm under running
water. Use a thin pointed tool, e.g. a
toothpick, to remove particles of soil
from the holes.
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter
(A). Turn it clockwise until it locks.
CAUTION!
An incorrect position of the
filters can cause bad
washing results and damage
to the appliance.
3. To install the spray arm back, press it
downwards.
www.aeg.com20
11. TROUBLESHOOTING
WARNING!
Improper repair of the
appliance may pose a
danger to the safety of the
user. Any repairs must be
performed by qualified
personnel.
The majority of problems that may
to contact an Authorised Service
Centre.
Refer to the below table for information
on possible problems.
With some problems, the lights related
to MY TIME selection bar flash
intermittently to indicate a malfunction
and the alarm code.
occur can be solved without the need
Problem and alarm code Possible cause and solution
You cannot activate the appliance.
The programme does not
start.
The appliance does not fill
with water.
• The lights related to
MY TIME selection bar
flash 1 time intermittently.
• An acoustic signal
sounds intermittently.
The appliance does not
drain the water.
• The lights related to
MY TIME selection bar
flash 2 times intermittently.
• An acoustic signal
sounds intermittently.
The anti-flood device is on.
• The lights related to
MY TIME selection bar
flash 3 times intermittently.
• An acoustic signal
sounds intermittently.
• Make sure that the mains plug is connected to the
mains socket.
• Make sure that there is no damaged fuse in the fuse
box.
• Make sure that the appliance door is closed.
• If the delay start is set, cancel the setting or wait for the
end of the countdown.
• The appliance recharges the resin inside the water softener. The duration of the procedure is approximately 5
minutes.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not
too low. For this information, contact your local water
authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter in the inlet hose is not clogged.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the sink spigot is not clogged.
• Make sure that the interior filter system is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Close the water tap.
• Make sure that the appliance is correctly installed.
• Make sure the baskets are loaded as instructed in the
user manual.
Problem and alarm code Possible cause and solution
Malfunction of the water level detection sensor.
• Make sure that the filters are clean.
• Switch the appliance off and on.
• The lights related to
MY TIME selection bar
flash 4 times intermittently.
• An acoustic signal
sounds intermittently.
Malfunction of the wash
• Switch the appliance off and on.
pump or the drain pump.
• The lights related to
MY TIME selection bar
flash 5 times intermittently.
• An acoustic signal
sounds intermittently.
The temperature of the water inside the appliance is
too high or malfunction of
• Make sure that the temperature of the inlet water does
not exceed 60°C.
• Switch the appliance off and on.
the temperature sensor occurred.
• The lights related to
MY TIME selection bar
flash 6 times intermittently.
• An acoustic signal
sounds intermittently.
Technical malfunction of the
• Switch the appliance off and on.
appliance.
• The lights related to
MY TIME selection bar
flash 12 times intermittently.
• An acoustic signal
sounds intermittently.
The level of water inside the
appliance is too high.
• The lights related to
MY TIME selection bar
flash 15 times intermit-
• Switch the appliance off and on.
• Make sure that the filters are clean.
• Make sure that the outlet hose is installed at the right
height above the floor. Refer to the installation instructions.
tently.
• An acoustic signal
sounds intermittently.
The appliance stops and
starts more times during op-
• It is normal. It provides optimal cleaning results and energy savings.
eration.
ENGLISH 21
www.aeg.com22
Problem and alarm code Possible cause and solution
The programme lasts too
long.
Small leak from the appliance door.
The appliance door is difficult to close.
Rattling or knocking sounds
from the inside of the appliance.
The appliance trips the circuit-beaker.
• If the delay start option is set, cancel the delay setting or
wait for the end of the countdown.
• Activating ExtraPower increases the programme duration.
• The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
• The appliance door is not centred on the tub. Adjust the
rear foot (if applicable).
• The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable).
• Parts of the tableware are protruding from the baskets.
• The tableware is not properly arranged in the baskets.
Refer to basket loading leaflet.
• Make sure that the spray arms can rotate freely.
• The amperage is insufficient to supply simultaneously all
the appliances in use. Check the socket amperage and
the capacity of the meter or turn off one of the appliances in use.
• Internal electrical fault of the appliance. Contact an Authorised Service Centre.
Once you have checked the appliance,
deactivate and activate the appliance. If
the problem occurs again, contact an
Authorised Service Centre.
For alarm codes not described in the
table, contact an Authorised Service
Centre.
WARNING!
We do not recommend
using the appliance until the
problem has been
completely fixed. Unplug the
appliance and do not plug it
in again until you are certain
that it operates correctly.
11.1 The washing and drying results are not satisfactory
Problem Possible cause and solution
Poor washing results. • Refer to "Daily use", "Hints and tips" and the basket
loading leaflet.
• Use more intensive washing programme.
• Activate the ExtraPower option to improve the washing results of a selected programme.
• Clean spray arm jets and filter. Refer to "Care and
Cleaning".
ENGLISH 23
Problem Possible cause and solution
Poor drying results. • Tableware was left for too long inside the closed appli-
ance. Activate AirDry to set the automatic opening of
the door and to improve the drying performance.
• There is no rinse aid or the dosage of rinse aid is not
sufficient. Fill the rinse aid dispenser or set the level of
rinse aid to a higher level.
• The quality of the rinse aid can be the cause.
• We recommend to use rinse aid always, even in combination with multi-tablets.
• Plastic items may need to be towel dried.
• The programme does not have the drying phase. Refer to "Programmes overview".
There are whitish streaks or
bluish layers on glasses and
dishes.
There are stains and dry water
drops on glasses and dishes.
• The released quantity of rinse aid is too high. Adjust
the rinse aid level to a lower level.
• The quantity of detergent is too high.
• The released quantity of rinse aid is not sufficient. Adjust the rinse aid level to a higher level.
• The quality of the rinse aid can be the cause.
The interior of the appliance is
wet.
• This is not a defect of the appliance. Humid air condensates on the appliance walls.
Unusual foam during washing. • Use the detergent designed specifically for dishwash-
ers.
• There is a leak in the rinse aid dispenser. Contact an
Authorised Service Centre.
Traces of rust on cutlery. • There is too much salt in the water used for washing.
Refer to "The water softener".
• Silver and stainless steel cutlery were placed together.
Do not put silver and stainless steel items close together.
There are residues of detergent in the dispenser at the
end of the programme.
• The detergent tablet was stuck in the dispenser and
therefore was not completely washed away by water.
• Water cannot wash away the detergent from the dispenser. Make sure that the spray arms are not blocked
or clogged.
• Make sure that items in the baskets do not impede the
lid of the detergent dispenser from opening.
Odours inside the appliance. • Refer to "Internal cleaning".
• Start the Machine Care programme with a descaler or
a cleaning product designed for dishwashers.
www.aeg.com24
Problem Possible cause and solution
Limescale deposits on the tableware, on the tub and on
the inside of the door.
Dull, discoloured or chipped
tableware.
• The level of salt is low, check the refill indicator.
• The cap of the salt container is loose.
• Your tap water is hard. Refer to "The water softener".
• Use salt and set regeneration of the water softener
even when multi-functional tablets are used. Refer to
"The water softener".
• Start the Machine Care programme with a descaler
designed for dishwashers.
• If limescale deposits still remain, clean the appliance
with appliance cleaners which are particularly suitable
for this purpose.
• Try a different detergent.
• Contact the detergent manufacturer.
• Make sure that only dishwasher-safe items are washed
in the appliance.
• Load and unload the basket carefully. Refer to the basket loading leaflet.
• Place delicate items in the upper basket.
Refer to "Before first use",
"Daily use", or "Hints and
tips" for other possible
causes.
12. TECHNICAL INFORMATION
Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550
Electrical connection
Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)
Water supply
Capacity Place settings 13
Power consumption Left-on mode (W) 5.0
1)
Refer to the rating plate for other values.
2)
If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to
decrease energy consumption.
1)
12.1 Link to the EU EPREL
database
The QR code on the energy label
supplied with the appliance provides a
Voltage (V) 220 - 240
Frequency (Hz) 50
Cold water or hot water
Off-mode (W) 0.50
max 60 °C
2)
web link to the registration of this
appliance in the EU EPREL database.
Keep the energy label for reference
together with the user manual and all
other documents provided with this
appliance.
ENGLISH 25
It is possible to find information related
to the performance of the product in the
EU EPREL database using the link
https://eprel.ec.europa.eu and the
model name and product number that
you can find on the rating plate of the
appliance. Refer to the chapter "Product
description".
For more detailed information about the
energy label, visit
www.theenergylabel.eu.
13. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol
.
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
*
www.aeg.com/shop
156935221-A-182020
Loading...