AEG F55011VI User Manual [da]
FAVORIT 55011 VI
User manual Dishwasher
Benutzerinformation Geschirrspüler
Contents
2
Thank you for choosing one of our high-quality products.
To ensure optimal and regular performance of your appliance please read this
instruction manual carefully. It will enable you to navigate all processes perfectly
and most efficiently. To refer to this manual any time you need to, we recommend
you to keep it in a safe plac e. An d p le as e pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
Contents
Operating instructions 3
Safety information 3
Correct use 3
General safety 3
Child safety 3
Installation 4
Product description 4
Control panel 5
Digital display 6
Delay start button 6
Programme selection buttons 6
Function buttons 6
Setting mode 6
Audible signals 6
Use of the appliance 7
Setting the water softener 7
Manual adjustment 8
Electronic adjustment 8
Use of dishwasher salt 9
Use of rinse aid 9
Adjusting the rinse aid dosage 10
Loading cutlery and dishes 11
Helpful hints and tips 11
Lower basket 12
Cutlery basket 12
Upper basket 13
Adjustment of the height of the upper
basket 14
Use of detergent 14
Multitab function 16
To activate the rinse aid dispenser 16
Washing programmes 17
Setting and starting a washing programme
Interrupting a washing programme 18
Cancelling a washing programme 18
Setting and starting a washing programme
with delay start 19
Cancelling a delay start 19
End of the washing programme 19
Removing the load 19
Care and cleaning 19
Cleaning the filters 20
External cleaning 21
Frost precautions 21
What to do if… 21
Technical data 23
Installation instructions 23
Installation 23
Attaching the appliance to the adjacent
units 23
Adjusting the level of the appliance 24
Water connection 24
Water inlet hose 24
Water drain hose 25
Electrical connection 26
Environment concerns 26
Subject to change without notice
18
Safety information
Operating instructions
Safety information
For your safety and correct operation of the appliance, read this manual carefully before
installation and use. Always keep these instructions with the appliance even if you move
or sell it. Users must fully know the operation and safety features of the appliance.
Correct use
• The appliance is designed exclusively for domestic use.
• Only use the appliance to clean household utensils that are applicable for dishwashers.
• Do not put solvents in the appliance. Risk of explosion.
• Put the knives and all items with sharp points in the cutlery basket with their points
down. If not, put in a horizontal position in the upper basket.
• Use only branded products for dishwashers (detergent, salt, rinse aid).
• If you open the door while the appliance is in operation, hot steam can escape. Risk of
skin burns.
• Do not remove dishes from the dishwasher before the end of the washing programme.
• When the washing programme is completed, disconnect the mains plug from the mains
socket and close the water tap.
• Only an authorised service engineer can repair this appliance. Use only original spare
parts.
• Do not do repairs yourself to prevent injury and damage to the appliance. Always contact
your local Service Force Centre.
3
General safety
• Persons (including children) with reduced physical sensory, mental capabilities or lack
of experience and knowledge must not use the appliance. They must have supervision
or instruction for the operation of the appliance by a person responsible for their safety.
• Obey the safety instructions from the manufacturer of the dishwasher detergent to
prevent burns to eyes, mouth and throat.
• Do not drink the water from the dishwasher. Detergent residues can stay in your appliance.
• Always close the door when you do not use the appliance to prevent injury and not to
stumble over the open door.
• Do not sit or stand on the open door.
Child safety
• Only adults can use this appliance. Children must get supervision to make sure that they
do not play with the appliance.
• Keep all the packaging away from children. There is a risk of suffocation.
• Keep all detergents in a safe area. Do not let children touch the detergents.
• Keep children away from the appliance when the door is open.
Product description
4
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect a
damaged appliance. If necessary, contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do the electrical installation.
• A qualified and competent person must do the plumbing installation.
• Do not change the specifications or modify this product. Risk of injury and damage to
the appliance.
• Do not use the appliance:
– if the mains cable or water hoses are damaged,
– if the control panel, worktop or plinth area are damaged, that you can get access to
the inner side of the appliance.
Contact your local Service Force Centre.
• Do not drill into the sides of the appliance to prevent damage to hydraulic and electrical
components.
WARNING!
Carefully obey the instructions for electrical and water connections.
Product description
1 Upper basket
2 Water hardness dial
3 Salt container
4 Detergent dispenser
5 Rinse aid dispenser
Control panel
6 Rating plate
7 Filters
8 Lower spray arm
9 Upper spray arm
Control panel
1 Digital display
2 Delay start button
3 Programme selection buttons
4 Indicator lights
5 On/off button
6 Function buttons
Indicator lights
MULTITAB Comes on when you activate the multitab function. Refer
1)
Salt
End-of-programme Comes on when the washing programme is completed.
1) When the salt container is empty, the related indicator light does not come on while a washing programme
operates.
to the chapter 'Multitab function'.
Comes on when it is necessary to fill the salt container.
Refer to the chapter 'Use of dishwasher salt'.
After you fill the container, the salt indicator light can
continue to stay on for some hours. This does not have
an unwanted effect on the operation of the appliance.
Auxiliary functions:
• Level of the water softener.
• Activation/deactivation of the audible signals.
• Activation/deactivation of the rinse aid dispenser.
• An alarm if the appliance has a malfunction.
5
Control panel
6
Digital display
The display shows:
• Number of hours for the delay start.
• If the appliance is in setting mode.
• If a washing programme is set.
Delay start button
Use the delay start button to delay the start of the washing programme with an interval
between 1 and 9 hours. Refer to the chapter 'Setting and starting a washing programme'.
Programme selection buttons
With these buttons you can select the washing programme. Press a programme button,
the related indicator light comes on. Refer to 'Washing programmes' chapter for more data
about the washing programmes.
Function buttons
Use the function buttons for these operations:
• To set the water softener. Refer to the chapter 'Setting the water softener'.
• To deactivate/activate the audible signals. Refer to the section 'Audible signals'.
• To activate/deactivate the multitab function. Refer to the chapter 'Multitab function'.
• To deactivate/activate the rinse aid dispenser when multitab function is active. Refer to
the chapter 'Multitab function'.
• To cancel the washing programme in progress or a delay start in progress. Refer to the
chapter 'Setting and starting a washing programme'.
Setting mode
The appliance must be in setting mode for these operations:
• To set a washing programme.
• To set the water softener level.
• To deactivate/activate the audible signals.
• To deactivate/activate the rinse aid dispenser.
Press the on/off button. The appliance is in setting mode when:
– All the programme indicator lights come on and the digital display shows three horizontal
bars.
Press the on/off button. The appliance is not in setting mode when:
– Only one programme indicator light comes on and the digital display shows one hori-
zontal bar.
– A washing programme is set. It is necessary to cancel the programme to go back to the
setting mode. Refer to the chapter 'Setting and starting a washing programme'.
Audible signals
You can hear an audible signal:
• At the end of the washing programme.
• During the setting of the level of the water softener.
• When the appliance has a malfunction.
The activation of the audible signals is set at the factory.
Do these steps to deactivate the audible signals:
Use of the appliance
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C until the indicator lights of function buttons
A, B and C start to flash.
4. Press the function button C.
– Indicator lights for function buttons A and B go off.
– Indicator light for function button C starts to flash.
– The end-of-programme indicator light comes on.
The audible signals are activated.
5. Press the function button C again.
– The end-of-programme indicator light goes off.
The audible signals are deactivated.
6. Switch off the appliance to save the operation.
Do these steps to activate the audible signals:
1. Do the above procedure until the end-of-programme indicator light comes on.
Use of the appliance
Refer to the following instructions for each step of procedure:
1. Make a check if the water softener level is correct for the water hardness in your area.
If necessary set the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dishwasher.
5. Set the correct washing programme for the type of load and soil.
6. Fill the detergent dispenser with the correct quantity of detergent.
7. Start the washing programme.
If you use combi detergent tablets ('3 in 1', '4 in 1', '5 in 1', etc.), refer to the chapter 'Multitab
function'.
7
Setting the water softener
The water softener removes minerals and salts from the water supply. Minerals and salts
can have bad effect on the operation of the appliance.
Water hardness is measured in equivalent scales:
• German degrees (dH°).
• French degrees (°TH).
• mmol/l (millimol per litre - international unit for the hardness of water).
•Clarke.
Adjust the water softener to the water hardness in your area. If necessary, contact your
local water authority.
Setting the water softener
8
Water hardness Water hardness setting
°dH °TH mmol/l Clarke manually electronically
51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10
43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9
37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8
29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7
23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6
19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5
15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4
11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3
4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2
< 4 < 7 < 0,7 < 5
1) No use of salt required.
You must set the water softener manually and electronically.
Manual adjustment
The appliance is set at the factory at position 2.
1)
1
1)
1
1. Open the door.
2. Remove the lower basket.
3. Turn the water hardness dial to position 1
or 2 (refer to the chart).
4. Install the lower basket.
5. Close the door.
Electronic adjustment
The water softener is set at the factory at level 5.
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C until the indicator lights for function buttons
A, B and C start to flash.
4. Release function buttons B and C.
5. Press function button A.
– The indicator light for function button A continues to flash.
– The indicator lights for function buttons B and C go off.
– The end-of-programme indicator light starts to flash.
– You can hear an audible signal.
The setting function of the water softener is activated.
Use of dishwasher salt
The end-of-programme indicator light flashes and an audible signal operates to show
the level of the water softener. The pause is approximately 3 seconds.
Example: 5 flashes / 5 intermittent audible signals - pause - 5 flashes / 5 intermittent
audible signals - pause - etc. = level 5
6. Press the function button A one time to increase the water softener level by one step.
7. Press the on/off button to save the operation.
Use of dishwasher salt
CAUTION!
Only use dishwashers salt. Types of salt that are not applicable for dishwashers cause damage to the water softener.
CAUTION!
Grains of salt and salty water on the bottom of the appliance can cause corrosion. Fill the
appliance with salt before you start a washing programme to prevent corrosion.
Do these steps to fill the salt container:
1. Turn the cap anticlockwise to open the salt container.
2. Fill the salt container with 1 litre of water (only the first operation).
3. Use the funnel to fill the salt container
with salt.
4. Remove the salt around the opening of
the salt container.
5. Turn the cap clockwise to close the salt
container.
It is normal that water overflows from the salt
container when you fill it with salt.
9
Use of rinse aid
CAUTION!
Only use branded rinse aid for dishwashers.
Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid
detergent). This can cause damage to the appliance.
Rinse aid makes it possible to dry the dishes without streaks and stains.
Rinse aid is automatically added during the last rinsing phase.
Do these steps to fill the rinse aid dispenser:
Use of rinse aid
10
1. Press the release button (A) to open the
rinse aid dispenser.
2. Fill the rinse aid dispenser with rinse aid.
The mark 'max.' shows the maximum level.
3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam during
the subsequent washing programme.
4. Close the rinse aid dispenser.
Fill the rinse aid dispenser when the rinse aid indicator (B) becomes clear.
Adjusting the rinse aid dosage
The rinse aid is set at the factory at position 4.
Loading cutlery and dishes
You can set the rinse aid dosage between position 1 (lowest dosage) and position 6 (highest
dosage).
Turn the rinse aid dial to increase or decrease the
dosage.
– Increase the dosage if there are water droplets
or limescale on the dishes.
– Decrease the dosage if there are streaks, whitish
stains or bluish layers on the dishes.
Loading cutlery and dishes
Helpful hints and tips
CAUTION!
Only use the appliance for household utensils that are applicable for dishwashers.
11
Do not use the appliance to clean objects that can absorb water (sponges, household cloths,
etc.).
• Before you load cutlery and dishes, do these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
• While you load cutlery and dishes, do these steps:
– Load hollow items (e.g. cups, glasses and pans) with the opening down.
– Make sure that water does not collect in the container or in a deep base.
– Make sure that cutlery and dishes do not lie inside one another.
– Make sure that cutlery and dishes do not cover other cutlery and dishes.
– Make sure that glasses do not touch other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can keep water droplets. Plastic items do
not dry as well as porcelain and steel items.
• Put light items in the upper basket. Make sure that the items do not move.
CAUTION!
Make sure that the spray arms can move freely before you start a washing programme.
WARNING!
Always close the door after you load or unload the appliance. An open door can be dangerous.
Loading cutlery and dishes
12
Lower basket
Put large and heavily soiled dishes and pans in the
lower basket.
The rows of prongs in the lower basket can be flat
to load large dishes, pots, pans and bowls.
Cutlery basket
WARNING!
Do not put long-bladed knives in a vertical position. Arrange long and sharp cutlery horizontally in the upper basket. Be careful with sharp items.
Use the cutlery grids.
• Put the grids on the cutlery basket.
• For larger items use only one of the cutlery grids.
• Put forks and spoons with the handles down.
• Put knives with the handles up.
• Mix spoons with other cutlery to prevent
them to bond together.
Loading cutlery and dishes
13
Upper basket
The upper basket is for saucers, salad bowls, cups,
glasses, pots and lids. Arrange the items to let water touch all surfaces.
Use of detergent
14
• For longer items fold the cup racks up.
• Put glasses with long stems in the cup racks
with the stems up.
Adjustment of the height of the upper basket
You can put the upper basket in two positions to increase load flexibility.
Maximum height of the dishes in:
the upper basket the lower basket
Upper position 22 cm 30 cm
Lower position 24 cm 29 cm
Do these steps to move to the upper basket to the lower/upper position:
1. Pull out the upper basket until it stops.
2. Hold the upper basket by the handle, lift it
as far as possible and lower it vertically.
The upper basket latches into the lower or
the upper position.
Use of detergent
Only use detergents (powder, liquid or tablet) that are applicable for dishwashers.
Follow the data on the packaging:
• Dosage recommended by the manufacturer.
• Storage recommendations.
Do not use more than the correct quantity of detergent to save an environment.
Do these steps to fill the detergent dispenser:
1. Open the lid of the detergent dispenser.
2. Fill the detergent dispenser (A) with detergent. The marking shows the dosage:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent.
3. If you use a washing programme with prewash phase, put more detergent in the
prewash detergent compartment (B).
Use of detergent
A
B
15
4. If you use detergent tablets, put the detergent tablet in the detergent dispenser
(A).
5. Close the lid of the detergent dispenser.
Press the lid until it locks into position.
Different brands of detergent dissolve in different times. Some detergent tablets do not
have the best cleaning results during short washing programmes. Use long washing programmes when you use detergent tablets to fully remove the detergent.
Multitab function
16
Multitab function
The multitab function is for combi detergent tablets.
These tablets contain agents such as detergent, rinse aid and dishwasher salt. Some types
of tablets can contain other agents.
Do a check if these tablets are applicable for the local water hardness. Refer to the instructions from the manufacturer.
When you set the multitab function, it stays on until you deactivate it.
The multitab function stops automatically the flow of rinse aid and salt. The salt indicator
light is deactivated.
The programme duration can increase if you use the multitab function.
Activate or deactivate the multitab function before the start of a washing programme.
You cannot activate or deactivate the multitab function when the programme operates.
Cancel the washing programme, then set the programme again.
To activate the multitab function:
• Press and hold the two multitab buttons (function buttons D and E). The multitab indi-
cator light comes on.
To deactivate the multitab function:
• Press and hold the two multitab buttons (function buttons D and E). The multitab indi-
cator light goes off.
Do these steps if the drying results are not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position 2.
• You can only activate or deactivate the rinse aid dispenser when the multitab function
is activated.
To activate the rinse aid dispenser
1. Switch on the appliance.
2. Make sure that the appliance is in setting mode.
3. Press and hold function buttons B and C.
– The indicator lights for function buttons A, B, and C start to flash.
4. Press function button B.
– The indicator lights for function buttons A and C go off.
– The indicator light for function button B continues to flash.
5. Press function button B again.
– The end-of-programme indicator light comes on.
6. Switch off the appliance to save the operation.
To deactivate the rinse aid dispenser do the above steps until the end-of-programme indicator light goes off.
Washing programmes
To use normal detergent again:
1. Deactivate the multitab function.
2. Fill the salt container and rinse aid dispenser.
3. Adjust the water hardness setting to the highest level.
4. Do a washing programme without dishes.
5. Adjust the water softener to the water hardness in your area.
6. Adjust the rinse aid dosage.
Washing programmes
Washing programmes
Programme Degree of soil Type of load Programme description
INTENSIV CARE 70° Heavy soil Crockery, cutlery,
1)
AUTO
2)
30 MIN
3)
ECO 50°
1) During the Auto programme, the soil level of the dishes is given by how cloudy the water is. The programme
duration and consumptions can change. This depends if the appliance is fully or not and on the level of soil on
the dishes. The appliance adjusts automatically the temperature of the water during the main wash.
2) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to
load breakfast and dinner crockery and cutlery.
3) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.
Any Crockery, cutlery,
Normal or light
soil
Normal soil Crockery and cutlery Prewash
Any Partial load (to be
pots and pans
pots and pans
Crockery and cutlery Main wash up to 60°C
completed later in the
day).
Consumption values
Programme Duration (in minutes) Energy (in kWh) Water (in litres)
INTENSIV CARE 70° 140 - 150 1,5 - 1,7 16 - 18
AUTO 90 - 130 1,1 - 1,7 12 - 23
30 MIN 30 0,9 9
ECO 50° 150 - 160 1,0 - 1,1 12 - 13
Prewash
Main wash up to 70°C
1 intermediate rinse
Final rinse
Drying
Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying
Final rinse
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
1 cold rinse (to prevent food
scraps to bond).
Detergent is not necessary with
this programme.
17
Loading...