user manual
Dishwasher
ESL 47030
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Safety information |
2 |
Unloading the dishwasher |
15 |
Product description |
3 |
Washing programmes |
15 |
Control panel |
4 |
Care and cleaning |
17 |
First use |
6 |
What to do if… |
18 |
Set the water softener |
6 |
Technical data |
19 |
Use of dishwasher salt |
7 |
Hints for test institutes |
20 |
Use of rinse aid |
8 |
Installation |
21 |
Daily use |
8 |
Water connection |
21 |
Load cutlery and dishes |
9 |
Electrical connection |
23 |
Use of detergent |
12 |
Environment concerns |
23 |
Multitab function |
13 |
|
|
Select and start a washing programme |
14 |
|
|
|
|
|
|
|
|
Subject to change without notice |
Safety information
In the interest of your safety and to en- |
• |
Avoid opening the door whilst the appli- |
|
sure the correct use, before installing |
|
ance is in operation, hot steam may es- |
|
and first using the appliance, read this |
|
cape. |
|
user manual carefully, including its hints |
• |
Do not take any dishes out of the dish- |
|
and warnings. To avoid unnecessary |
|
washer before the end of the washing cy- |
|
mistakes and accidents, it is important |
|
cle. |
|
to ensure that all people using the appli- |
• |
After use, isolate the appliance from the |
|
ance are thoroughly familiar with its op- |
|
power supply and turn off the water sup- |
|
eration and safety features. Save these |
|
ply. |
|
instructions and make sure that they re- |
• This product should be serviced only by an |
||
main with the appliance if it is moved or |
|
authorized service engineer, and only gen- |
|
sold, so that everyone using it through |
|
uine spare parts should be used. |
|
its life will be properly informed on appli- |
• |
Under no circumstances should you at- |
|
ance use and safety. |
|
tempt to repair the machine yourself. Re- |
|
Correct use |
|
pairs carried out by inexperienced persons |
|
|
could cause injury or serious malfunction- |
||
• This dishwasher is only intended for wash- |
|
||
|
ing. Contact your local Service Force Cen- |
||
ing household utensils suitable for ma- |
|
tre. Always insist on genuine spare parts. |
|
chine washing. |
General safety |
||
• Do not put any solvents in the dishwasher. |
|||
• Persons (including children) with reduced |
|||
This could cause an explosion. |
|||
• Knives and other items with sharp points |
|
physical sensory, mental capabilities or |
|
must be loaded in the cutlery basket with |
|
lack of experience and knowledge must |
|
their points down or placed in a horizontal |
|
not use the appliance. They must have su- |
|
position in the upper basket. |
|
pervision or instruction for the operation of |
|
• Only use products (detergent, salt and |
|
the appliance by a person responsible for |
|
rinse aid) suitable for dishwashers. |
|
their safety. |
•Dishwasher detergents can cause chemical burns to eyes, mouth and throat. Could endanger life! Comply with the safety instructions of the dishwasher detergent manufacturer.
•Water in the dishwasher is not for drinking purposes. Detergent residue may still be present in your machine.
•Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded. In this way you will avoid anybody tripping over the open door and hurting themselves.
•Do not sit or stand on the open door.
Child safety
•This appliance is designed to be operated by adults. Children must be supervised to ensure that they do not play with the appliance.
•Keep all packaging well away from children. There is a risk of suffocation.
•Keep all detergents in a safe place out of children’s reach.
•Keep children well away from the dishwasher when the door is open.
Installation
•Check your dishwasher for any transport damage. Never connect a damaged ma-
Product description
electrolux 3
chine. If your dishwasher is damaged contact your supplier.
•All packaging must be removed before use.
•Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person.
•For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way.
•Never use the dishwasher if the electrical supply cable and water hoses are damaged; or if the control panel, work top or plinth area are damaged such that the inside of the appliance is freely accessible. Contact your local Service Force centre, in order to avoid hazard.
•All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components.
Warning! For electrical and water connection carefully follow the instructions given in the specific paragraphs.
4 electrolux
1Upper basket
2Water hardness dial
3Salt container
4Detergent dispenser
5Rinse aid dispenser
6Rating plate
7Filters
8Lower spray arm
9Upper spray arm
This dishwasher has an internal light that turns on when the door opens and off when it closes.
Internal light equipped with led lamp CLASS 1 in accordance with EN 60825-1: 1994 + A1:2002 + A2:2001. In case this light has to be replaced please contact your local Service Force Centre.
Optical signal
Once the washing programme starts, a point-shaped optical signal shows on the floor beneath the appliance door.
If you install the appliance higher up with a furniture door mounted flush, the optical signal can no longer be seen.
|
Optical signal |
Red light fixed |
Indicates the running of a wash- |
|
ing programme. Comes on |
|
when the programme starts. |
|
Goes off once the programme |
|
has ended. |
Red light |
Indicates a malfunction of the |
flashing |
appliance. |
Green light |
Indicates the end of the wash- |
fixed |
ing programme. |
|
|
Control panel
7 |
8 |
9
1On/off button
2Digital display
3Delay start button
4Programme selection buttons
5Sanitise button
6Multitab button (Multitab)
7Cancel button (Cancel)
8Indicator lights
9Function buttons
|
Indicator lights |
|
1) |
|
Comes on when the rinse aid has run out. |
|
|
|
1) |
|
Comes on when the special salt has run out. |
|
|
|
electrolux 5
Indicator lights
Comes on when a washing programme has ended.
1)The salt and rinse aid indicator lights never come on while a washing programme is running even if filling with salt and/or rinse aid is necessary.
The digital display
The digital display indicates:
•the level of hardness to which the water softener is set,
•the number corresponding to the washing programme,
•the approximate remaining time of the running programme,
•activation/deactivation of the rinse aid dispenser ( ONLY with 'Multitab' function active).
•the end of a washing programme (the digital display shows a zero),
•the countdown for the delay start,
•fault codes concerning malfunction of the appliance,
•activation/deactivation of the audible signals.
Delay start button
You can delay the start of the programme for between 1 and 19 hours.
Refer to 'Select and start a washing programme' chapter for the set of this function.
Programme selection buttons
Press one of these buttons until the display shows the number of the desired programme. Refer to 'Washing programmes' chart for details.
Sanitise button
This function gives more hygiene to dishes and glasses.
During the last rinse, the temperature increases to 68°C and stays above 65°C from 10 to 14 minutes.
This function is not available with all washing programmes. Refer to 'Washing programmes' chart for details.
Do these steps to select the sanitise function:
1.Set the washing programme.
2.Press the sanitise button,
–if the sanitise indicator light comes on, the function is available,
–if the sanitise indicator light stays off, the function is not available.
Multitab button
Set this function when you use combi detergent tablets (3 in 1, 4 in 1, 5 in 1, etc.). Refer to 'Multitab function' chapter.
Cancel button
With this button you can cancel a washing programme or a delay start in progress.
Function buttons (A, B and C)
The following functions can be set using these buttons:
•setting the water softener level,
•activation/deactivation of the rinse aid dispenser when Multitab function is active,
•activation/deactivation of the audible signals.
Setting mode
Press the on/off button. If the lights of the programme selection buttons come on and the digital display shows 2 horizontal bars, the appliance is in setting mode.
Always remember that when performing the following operations:
–selecting a washing programme,
–setting the water softener level,
–activating/deactivating the rinse aid,
–activating/deactivating the audible
signals,
the appliance MUST be in setting mode.
Press the on/off button. If the lights of the programme selection buttons come on and the digital display shows the time duration (in minutes) of a programme, this means that the last performed or selected programme is still set. In this case, to return to setting mode, the programme has to be cancelled.
To cancel a set programme or a programme in progress
•Press and hold the cancel button until the digital display shows 2 horizontal bars. The programme has been cancelled and the appliance is now in setting mode.
6 electrolux
First use
Before using your dishwasher for the first time:
•Ensure that the electrical and water connections comply with the installation instructions
•Remove all packaging from inside the appliance
•Set the water softener level
•Pour 1 litre of water into the salt container and then fill with dishwasher salt
•Fill the rinse aid dispenser
If you want to use combi detergent tablets such as: ''3 in 1'', ''4 in 1'', ''5 in 1'' etc... set the Multitab function. (See ''Multitab function'').
Set the water softener
The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply, which would have a detrimental or adverse effect on the operation of the appliance.
The higher the content of these minerals and salts, the harder your water is. Water hardness is measured in equivalent scales, German degrees (dH°), French degrees (°TH) and mmol/l (millimol per litre - international unit for the hardness of water).
The softener should be adjusted according to the hardness of the water in your area. Your local Water Authority can advise you on the hardness of the water in your area.
The water softener must be set in two ways: manually, using the water hardness dial and electronically.
|
Water hardness |
|
Adjusting the water hardness setting |
Use of |
||
°dH |
|
°TH |
mmol/l |
manually |
electronically |
salt |
|
||||||
|
|
|||||
51 - 70 |
|
91 - 125 |
9,1 - 12,5 |
2 |
level 10 |
yes |
43 - 50 |
|
76 - 90 |
7,6 - 9,0 |
2 |
level 9 |
yes |
37 - 42 |
|
65 - 75 |
6,5 - 7,5 |
2 |
level 8 |
yes |
29 - 36 |
|
51 - 64 |
5,1 - 6,4 |
2 |
level 7 |
yes |
23 - 28 |
|
40 - 50 |
4,0 - 5,0 |
2 |
level 6 |
yes |
19 - 22 |
|
33 - 39 |
3,3 - 3,9 |
2 |
level 5 |
yes |
15 - 18 |
|
26 - 32 |
2,6 - 3,2 |
1 |
level 4 |
yes |
11 - 14 |
|
19 - 25 |
1,9 - 2,5 |
1 |
level 3 |
yes |
4 - 10 |
|
7 - 18 |
0,7 - 1,8 |
1 |
level 2 |
yes |
< 4 |
|
< 7 |
< 0,7 |
1 |
level 1 |
no |
|
|
|
|
|
|
|
Setting manually
The dishwasher is factory set at position 2.
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3.Turn the water hardness dial to position 1 or 2 (see chart).
4.Replace the lower basket.
Setting electronically
The dishwasher is factory set at level 5.
1.Press the On/Off button. The dishwasher must be in setting mode.
2.Simultaneously press and hold function buttons B and C , until the lights of function buttons A , B and C start flashing.
3.Press function button A , the lights of function buttons B and C go off while the light of function button A continues to flash. The digital display shows the current level and a sequence of intermittent audible signals are heard.
Examples:
displayed, 5 intermittent audible signals, pause, etc. = level 5
electrolux 7
displayed, 10 intermittent audible signals, pause, etc. = level 10
4.To change the level, press function button A . Each time the button is pressed the level changes. (For the selection of the new level see the chart).
Examples: If the current level is 5, by pressing function button A once, level 6 is selected.
If the current level is 10, by pressing function button A once, level 1 is selected.
5.To memorize the operation, switch off the dishwasher by pressing the On/Off button.
Use of dishwasher salt
Warning!
Only use salt specifically designed for use in dishwashers. All other types of salt not specifically designed for use in a dishwasher, especially table salt, will damage the water softener. Only fill with salt just before starting one of the complete washing programmes. This will prevent any grains of salt or salty water, which may have been spilt, remaining on the bottom of the machine for any period of time, which may cause corrosion.
To fill:
1.Open the door, remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise.
2.Pour 1 litre of water into the container
(this is necessary only before filling with salt for the first time) .
3.Using the funnel provided, pour in the salt until the container is full.
4.Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket.
5.Replace the cap tightly turning it clockwise until it stops with a click.
Do not worry if water overflows from the unit when filling with salt, this is quite normal.
The salt indicator light on the control panel can remain illuminated for 2-6 hours after the salt has been replenished, assuming the dishwasher remains switched on. If you are using salt that takes longer to dissolve then this can take longer. The operation of the machine is not affected.
8 electrolux
Use of rinse aid
Warning! Only use branded rinse aid for dishwashers.
Never fill the rinse aid dispenser with any other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.
Rinse aid ensures thorough rinsing, and spot and streak free drying.
Rinse aid is automatically added during the last rinse.
1.Open the container by pressing the release button (A).
The dispenser holds about 110 ml of rinse aid, which is sufficient for between 16 and 40 washing cycles, depending upon the dosage setting.
3.Ensure that the lid is closed after every refill.
Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash.
According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage).
The dose is factory set in position 4. Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades.
2.Add the rinse aid in the container. The maximum level for filling is indicated by "max".
Daily use
•Check if it’s necessary to refill with dishwasher salt or rinse aid.
•Load cutlery and dishes into the dishwasher.
•Fill with dishwasher detergent.
•Select a wash programme suitable for the cutlery and dishes.
•Start the wash programme.
Helpful hints and tips
Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher.
•Before loading the dishes, you should:
–Remove all left over food and debris.
–Soften remnants of burnt food in pans
•When loading the dishes and cutlery, please note:
–Dishes and cutlery must not impede the rotation of the spray arms.
–Load hollow items such as cups, glasses, pans, etc. with the opening
electrolux 9
downwards so that water cannot collect in the container or a deep base.
–Dishes and items of cutlery must not lie inside one another, or cover each other.
–To avoid damage to glasses, they must not touch.
–Lay small objects in the cutlery basket.
•Plastic items and pans with non stick coatings have a tendency to retain water drops; these items will not dry as well as porcelain and steel items.
•Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable:
•Cutlery with wooden, horn, china or mother-of- pearls handles.
•Plastic items that are not heat resistant.
•Older cutlery with glued parts that are not temperature resistant.
•Bonded cutlery items or dishes.
•Pewter or copper items.
•Lead crystal glass.
•Steel items prone to rusting.
•Wooden platters.
•Items made from synthetics fibres.
are of limited suitability:
•Only wash stoneware in the dishwasher if it is specially marked as being dishwasher-safe by the manufacturer.
•Glazed patterns may fade if machine washed frequently.
•Silver and aluminium parts have a tendency to discolour during washing: Residues, e.g. egg white, egg yolk and mustard often cause discolouring and staining on silver. Therefore always clean left-overs from silver immediately, if it is not to be washed straight after use.
Load cutlery and dishes
The lower basket
The lower basket is designed to take saucepan, lids, plates, salad bowls, cutlery ect. Service dishes and large lids should be arranged around the edge of the basket, ensuring that the spray arms can turn freely.
The rows of prongs in the lower basket can lie flat to allow you to load pots, pans and bowls.