Advanced Energy ARTESYN INTELLIGENT MP User Manual

ARTESYN INTELLIGENT MP SERIES

Up to 1500 Watts

Advanced Energy's Artesyn iMP1 series is an AC input to DC output configurable power system consisting of a microprocessor-controlled PFC front end providing seven slots that accept intelligent DC-DC converter modules with single, dual or triple outputs ranging from 2 V to 60 V. Single output modules come in four power ranges that can be mixed and matched and connected in parallel or series to obtain thousands of output combinations customized to any application.



SPECIAL FEATURES



Full medical EN60601 approval



Intelligent I



Voltage adjustment on all outputs (manual or I



Configurable input and output OK signals and indicators



Configurable inhibit/enable



Configurable output UP/DOWN sequencing



Configurable current limit (foldback or constant current)



High power density (8.8 W/cu-in)



Intelligent fan (speed control/fault status)



Downloadable GUI from website



Customer provided air option



uP controlled PFC input with active inrush protection



C monitor of voltage, current, and

temp



Programmable voltage, current limit, inhibit/enable through I

C control

Optional extended hold-up module (SEMI F47 compliance)



Increased power density to 50% over standard MP



External switching frequency sync input



Optional conformal coating



Industrial temp range (-40 ºC to 70 ºC)



No preload required



Industrial shock/vibration (> 50G’s)

SAFETY



UL UL60950/UL2601**



CSA CSA22.2 No. 234 Level 5



TUV EN60950/EN60601-1**



BABT Compliance to EN60950/ EN60601 BS7002



CB Certificate and report



CE Mark to LVD

DATA SHEET

Total Power:

Up to 1500 W

Input Voltage:

85 - 264 Vac

120 - 300 Vdc

# of Outputs:

Up to 21

IMP

ELECTRICAL SPECIFICATIONS

Input

Input ra nge 85 - 264 Vac; 120 - 300 Vdc

(limited to 300 Vdc in medical applications)

Frequency 47 - 63 Hz (iMP1 47 - 440 Hz)

Inrush current 40 A peak maximum (soft start)

Efficiency Up to 85% @ full case load

Power Factor 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)

Turn-on time AC on 2.0 sec typ., inhibit/enable 150 ms typical

Programmable delay; 50 ms internal turn-on delay (Dual Output only)

EMI filter CISPR 22/EN55022 Level “B”**

Leakage current 300 µA max. @ 240 Vac; 47 - 63 Hz

Radiated EMI CISPR 22/EN55022 Level “B”**

Holdover storage 20 ms minimum (independent of input Vac) additional 34 ms holdover

storage with optional HUP module (SEMI F47 compatible). For iMP4 15 ms (low-line), 10 ms (high-line)

AC OK > 5 ms early warning min. before outputs lose regulation

Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)

Harmonic distortion Meets EN61000-3-2

Isolation Meets EN60950 and EN60601

Input to output: 4000 Vac; input to ground: 1500 Vac; output to ground: 400 Vdc Meets 1 MOPP Primary to ground, 2 MOPP Primary to Secondary

Global inhibit / enable TTL, Logic “1” and Logic “0”; configurable

Input fuse (internal) iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)

Warranty 2 years

2 advancedenergy.com

ELECTRICAL SPECIFICATIONS (CONTINUED)

Output

Adjustment range* ± 10% minimum all outputs (manual)

(full module adjustment range using I

Factory set point accuracy 1%

C output program accuracy ± 5%

Margining ± 4 - 6% nominal analog (single output module only)

Overall regulation 0.4% or 20 mV max. (1500 W modules 1% max.) (36 W modules 4% maximum)

Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to

20 MHz

Dynamic response < 2% or 100 mV, with 25% load step

Recovery time To within 1% in < 300 µsec

Overcurrent protection** Configurable through I

C (calibration required). Single output module and main output of the dual output module

105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current

Short-circuit protection Protected for continuous short-circuit.

Recovery is automatic upon removal of short

Overvoltage protection* Configurable through I

Single output module: 2 - 5.5 V 122 - 134%; 6 - 60 V 110 - 120%

Dual output module: 2 - 6 V 122 - 134%; 8 - 28 V 110 - 120%

Triple output module: 110 - 120% of highest voltage rating

Output (cont.)

Reverse voltage protection 100% of rated output current

Thermal protection* (OTP and OTW)

Configurable through I All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before

shutdown

Remote sense Up to 0.5 V total drop (not available on triple output module)

Single wire parallel Current share to within 2% of total rated current

DC OK* ± 5% of nominal. Configurable through I

Minimum load Not required

Housekeeping bias voltage 5 Vdc @ 1.0 A max. present whenever AC input is applied (Optional 2.0 A available)

Module inhibit* Configured and controlled through I

Switching frequency 250k Hz accepts external sync signal

Output/Output isolation > 1 Megohm, 500 V

External sync TTL clock input signal used to adjust switching frequency. Frequency 500 kHz

± 20%; Duty cycle 40 - 55%

* Can be c ontrol led via I2C ** Contro lled via I

C but requ ires loa d calibration

IMP

INTERNAL PART NUMBER REFERENCE TABLE

Part # Where X = Description Module Code

73-580-0001i N/A iMP8 Case iMP8

73-690-0001i N/A iMP1 Case iMP1

73-540-0001i N/A iMP4 Case iMP4

advancedenergy.com 3

IMP

ENVIRONMENTAL SPECIFICATIONS

Operating temperature -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. (-20 °C start up)

Storage temperature -40 °C to +85 °C

Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3

Humidity Operating; non-condensing 10% to 95% RH

Vibratio IEC68-2-6 to the levels of IEC721-3-2

MTBF demonstrated > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions

OUTPUT MODULE LINE-UP

Module Code 1 2 3 5 4

Module Type Single Single Single Single Dual Triple

Max output power 210 W 360 W 750 W 1500 W 144 W 36 W

Max output current 35 A 60 A 150 A 140 A 10 A 2 A

Output voltages available* 2 - 60 V 2 - 60 V 2 - 60 V 6 - 60 V 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*;

8 - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28,

24 - 28; 24 - 28, 2 - 6

Standard voltage increments 25 25 25 18 16 18

Remote sense Yes Yes Ye s Ye s Yes Yes No

Remote margin Yes Yes Yes Yes No No No

V-Program - I

Active Current Share Yes Yes Ye s Ye s Ye s No No

Module Inhibit - I

Module Inhibit - Analog Ye s Ye s Yes Yes Ye s No No

Overvoltage/Overcurrent protection

Minimum load required No No No No No No No

Slots occupied in any iVS case 1 2 3 4 1 1

* Note: Conta ct Factory for ex tende d range dow n to 6 V

C Control Yes Yes Yes Yes Yes Ye s No

C Control Ye s Ye s Ye s Yes Ye s Yes Yes

Yes Yes Yes Yes Yes Ye s Yes

8-15, 8-15, 2-6; 8-15, 8-15, 8-15;

8-15, 8-15, 18-28; 8-15, 18-28,

2-6

—

4 advancedenergy.com

OUTPUT MODULE VOLTAGE/CURRENT*

IMP

Voltage

Code

Single Output Module Code Dual Output*** Triple Output

1 2 3 5 4 4 - - -

Adjustment

Ranges****

2 V A 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 1.8 - 2.2

2.2 V B 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.0 - 2.4

3 V C 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.7 - 3.3

3.3 V D 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 3.0 - 3.6

5 V E 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 4.5 - 5.5

5.2 V F 35 A 60 A 144 A 288 A 10 A 10 A — — 2 A 4.7 - 5.7

5.5 V G 34 A 58 A 136 A 273 A 10 A 10 A — — 2 A 5.0 - 6.1

6.0 V H 23 A 42 A 97.5 A 250 A 10 A* 10 A* — — 2 A 5.4 - 6.6

8.0 V I 20 A 36 A 84.4 A 187.5 A 10 A 4 A 1 A 1 A 1 A 7.2 - 8.8

10 V J 18 A 32 A 75 A 140 A 10 A 4 A 1 A 1 A 1 A 9.0 - 11.0

11 V K 17 A 31 A 68 A 136.3 A 10 A 4 A 1 A 1 A 1 A 9.9 - 12.1

12 V L 17 A 30 A 62.5 A 125 A 10 A 4 A 1 A 1 A 1 A 10.8 - 13.2

14 V M 14 A 21 A 53.5 A 107 A 9 A 4 A 1 A 1 A 1 A 12.6 - 15.4

15 V N 14 A 20 A 50 A 100 A 8 A 4 A 1 A 1 A 1 A 13.5 - 16.5

18 V O 11 A 19 A 41.6 A 83.3 A — — — 0.5 A 0.5 A 16.2 - 19.8

20 V P 10.5 A 18 A 37.5 A 75 A — — — 0.5 A 0.5 A 18.0 - 22.0

24 V Q 8.5 A 15 A 30 A 62.5 A 4 A 2 A — 0.5 A 0.5 A 21.6 - 26.4

28 V R 6.7 A 11 A 26.8 A 53.5 A 3 A 2 A — 0.5 A 0.5 A 25.2 - 30.8

30 V S 6.5 A 11 A 25 A 50 A — — — — — 27.0 - 33.0

33 V T 6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3

36 V U 5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6

42 V V 4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2

48 V W 4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8

54 V X 3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4

60 V Y 3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0

Contact Factory

Special* Z 35 A 60 A 150 A 300 A — 10 A 2.3 - 2.6

Special* Z 35 A 60 A 150 A 300 A — 10 A 3.7 - 4.4

Special* Z 20 A 36 A 80 A 140 A — 8 A 6.7 - 7.1

* Note: Co ntact F actor y for exte nded ran ge down to 6 V. ** Increments o f current not shown c an be achieved by paralleli ng modul es (add curre nts of each module s elect ed). *** Total o utput p ower on dua l model mu st not exce ed 144 W. *** * For sing le output modul es only. Green reference lines indicate physical module groupings

advancedenergy.com 5

IMP

OUTPUT MODULE VOLTAGE/CURRENT* (CONTINUED)

Ordering Notes:

1. The cases and modules of both MP and iMP series can be interchanged to allow more flexibility. If intelligent modules are used with non-intelligent cases, a numeric code “4” is placed at the end of the module code (ex. 4LL0 becomes 4LL4).

2. USB to I

C module order code 73-769-001

ORDERING INFORMATION

Parallel Codes

Slot 4

Slot 3

Slot 5

Slot 6

Slot 5

Slot 7

Slot 5

Slot 6

7 6 5 4 3 2 1

Slot 2

Slot 3

Slot 4

Slot 2

Slot 3

Slot 4

Slot 2

iMP4

Slot 1

available slots

iMP8

available slots

Slot 1

iMP1

available slots

0 = no parallel 1 = 1 & 2 2 = 2 & 3 3 = 3 & 4 4 = 4 & 5 5 = 3 & 4 & 5 6 = 5 & 6 7 = 4 & 5 & 6 8 = 6 & 7 9 = 3 & 4, 6 & 7 A = 1 & 2, 3 & 4, 5 & 6 C = 2 & 3, 4 & 5 E = 3 & 4, 5 & 6 F = 2 & 3, 4 & 5, 6 & 7

Case Size Module/Voltage/Option Codes

iMP1* - 3L0 - 2E2 - 1Q1 - 4LL0 - 00 - A - ###

Case Size (mm)

4 = 2.5” x 5” x 10”; 750 W - 1158 W,

5 Slots (63.5 x 127 x 254 mm) 8 = 2.5” x 7” x 10”; 1000 W - 1200 W, 6 Slots (63.5 x 177.8 x 254 mm) 1 = 2.5” x 8” x 11”; 1200 W - 1500 W, 7 Slots (63.5 x 203.2 x 279.4 mm)

* Note: Add “E” af ter iMP4 to d enote IEC input option. e.g. iMP4E (Not ava ilable on iMP8 or iM P1)

First - Module Code

Second - Voltage Code

Third - Option Code

Module Codes

Module/voltage/option codes Module codes: (None) = 36 W triple O/P (1 slot) 1 = 210 W single O/P (1 slot) 2 = 360 W single O/P (2 slot) 3 = 750 W single O/P (3 slot) 4 = 144 W dual O/P (1 slot) 5 = 1500 W single O/P (4 slot) 6 - 9 = future

Voltage Codes:

See Output Module Voltage/ Current table above

Option Codes:

0 = Standard 1 = Module enable 2 = Constant current 3 = 1 & 2 combined 4 = Set for use in standard

(non-intelligent case) 5 = Shutdown mode for 1500 W 6 = 1 & 5 combined 7 - 9 = future

Case Option Codes Software Code Hardware Code

Case Option Codes

First digit 0 - 9, A - Z parallel code (See Parallel Codes table above)

Second digit 0 = No options 1 = Reverse air 3 = Global enable 4 = Fan idle with inhibit 5 = Opt 1 + Opt 3 6 = Opt 1 + Opt 4 7 = Opt 3 + Opt 4 8 = Opt 1 +3 +4 9 = RS485 73-544-002 A = RS485 73-544-002 + Reverse air C = Opt 3 + Opt 9 D = CAN BUS 73-544-003 E = Opt 3 + Opt D F = RS485 - MODBUS 73-544-005

Software code used for configuration change. “A” is standard

Factory assembled for hardware of firmware mods.

6 advancedenergy.com

ORDERING INFORMATION (CONTINUED)

S L O T

S L

S L O T

Single

210 W 360 W

iMP4 (AC input on opposite side)

iMP4 = 2.5” x 5” x 10” 5 available slots

(63.5 x 127 x 254 mm)

iMP8 and iMP1

IMP

Input 90 - 264 Vac 180 - 264 Vac 750 W max. 1158 W max.

750 W

1500 W ( 2.0 - 8.0 V)

1500 W ( 10 - 60 V)

1500 W with Bus Bar

Adapter Option (used with

the 10 - 60 V module)

iMP1 only

iMP8 = 2.5” x 7” x 10” 6 available slots

(63.5 x 177.8 x 254 mm)

iMP1 = 2.5” x 8” x 11” 7 available slots

(63.5 x 203.2 x 279.4 mm)

S L O T

85 - 264 Vac 180 - 264 Vac 1000 W max. 1200 W max.

1200 W max. 1500 W max.

Input

Dual

144 W

Triple

36 W

advancedenergy.com 7

IMP

PIN CONNECTORS

Figure 1. AC Input

Figure 2. Connector J1

Mates with Molex 90142-0010 Housing 90119-2110 Pin

Connector Kit Part No.: 70-841-004

Figure 3. Connector J2

10 6

Mates with Landwin 2050S1000 Housing 2053T011V Pin

or JST PHDR-10VS Housing JST SPHD-002T-P0.5 (28-24) JST SPHD-001T-P0.5 (26-22)

Connector Kit Part No.: 70-841-023

AC Input

Pin No. Function

1 AC neutral

2 AC line (hot)

3 Chassis (earth) ground

AC Input

Pin No. Function

1 Input AC OK - “emitter”

2 Input AC OK - “collector”

3 Global DC OK - “emitter”

4 Global DC OK - “collector”

5 External Sync

6 Global inhibit/optional enable logic “0”

7 Global inhibit/optional enable logic “1”

8 Global inhibit/optional enable return

9 +5 VSB housekeeping

10 +5 VSB housekeeping return

C Bus Output Connector

Pin No. Function

1 No connection

2 No connection

3 No connection

4 Serial clock signal (SCL)

5 Serial data signal (SDA)

6 Address bit 0 (A0)

7 Address bit 1 (A1)

8 Address bit 2 (A2)

9 Secondary return (GND)

10 5 Vcc external bus (5 VCC. Bus)

8 advancedenergy.com

MECHANICAL DRAWINGS

Figure 1. AC Input

.48” (12.1)

.63"

59.3 ± 0.2

DC OUTPUT CONNECTO

V1 ADJ

IMP

iMP Modules

DC-DC Converter Output Modules

Control Signal Information, J1 Control Connector

Pin No. Function

1 + Remote Sense single or dual o/p main

2 Remote Margin / V. Program single o/p

3 Margin High single o/p

4 - Remote Sense / Margin Low single or dual o/p main

5 Spare

6 Module, Isolated Inhibit single or dual o/p

7 Module Inhibit Return single or dual o/p

8 Current Share (SWP) single or dual o/p main

9 + Remote Sense V2 dual o/p, single is spare

10 - Remote Sense V2 dual o/p, single is spare

* Note: All iMP mo dules have a green DC OK LED. (excep t for 36 W module)

Figure 4. Connector J1

Mates with Molex 90142-0010 Housing 90119-2110 Pin

Single 1500 Wa 2-8 V

Single 210 Wa

.48"

1.38"

Single 360 Wa

(2X)

1.38” (35.2)

(35.1)

(12.1)

.44”

.44” (11.2)

.44"

(11.4)

.32" (8.1)

.63”

.33”

(16.0)

(8.5)

PIN 1

(11.4)

.32”

(8.1)

V+

M4X8 SCREWS WITH CONICAL WASHER

V-

V ADJ

PIN 1

DC OUTPUT CONNECTOR

V+

M 4 X 8 SCREWS WITH CONICAL WASHER

V-

V ADJ

DC OUTPUT CONNECTOR

Single 1500 Wa 10-60 VSingle 750 Wa

(2X)

.61"(15.6)

(2X)

1.24"(31.5)

Dual 144 Wa

.44"

(11.0)

.30 (7.5)

1.17 (29.7)

.59"

(15.0)

.32"

(8.1)

(16.0)

(3X)

.42 (10.7)

PIN 1

DC OUTPUT CONNECTOR

.46 (11.7)

(4X)

.32 (8.1)

V+

V-

M4X8 SCREWS

V ADJ

(4X)

V1 +

V1 -

V2 +

V2 -

M3X8 SCREWS WITH SPRING WASHER (4X)

V2 ADJ

V1 ADJ

PIN 1

Triple 36 Wa

11.3 ±0.8

For Factory-Use Only

VADJ

(3x) 31.6 ±0.8

8.1 ±0.8

PIN 1

V-

V+

V2 ADJ

V1+

V2+

V3+

V3 ADJ

Mates with Molex 09-91-0600 Housing 26-60-5060 Pin

M4X8 SCREWS W/ CONICAL WASHER (6X)

V1-

V2-

V3-

(2x) 15.0 ±0.8

(2x) 16.0 ±0.2

V1 +

V1 -

2 +

V2 -

V3 +

V3 -

advancedenergy.com 9

IMP

IMP SERIES

iMP4 (750/1158 Watts Max)

5-Inch Case Size: iMP4: 2.5” x 5” x 10” (63.5 mm x 127 mm x 254 mm)

Weight: iMP4 Case: 3 lbs. • 360 W Single 1.0 lb. • 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.

Notes:

1. Input: Barri er typ e. Three No. 6-3 2 B.H . screws (0.375” ce nters). Ma x torque: 6 i n-lbs. (0.67 N-m). (Optional I EC input c onnector)

2. Contr ol conne ctors: (J1) 10 position housing, g old plated cont acts . Mates wi th Molex 9 0142-0010 housing wi th 90119 -2110 crimp co ntact s (Molex C - Grid III Ser ies). Conn ector kit incl udes mat ing conn ector an d 10 pins, As tec par t #70-8 41-004. (J2) 10 po sition housing (L andwin 2 051P1000T). Mates with ho using 20 50S100 0 (Landw in) with 205 3T011P (Landwi n) pins or JST P HDR-IOVS Housing and JST S PHD-0 02T-PO. 5 pins .

3. Cha ssis mat erial: aluminum wi th chemical film c oating (co nducti ve).

4. All dim ensions are in mill imeter s and inch es, and are typic al.

5. Customer mounting -3 s ides M4, bottom also includes 8- 32 mount ing hole s. Max . penet ration i s 0.150” (3.8 mm). Ma x. torque: 5 in-lbs. (0.57 N-m).

6. Outp ut modul e connections : All singl e O/P module s are M4 x 8 mm sc rews. M ax. torq ue: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws . Max. to rque: 5 in-lbs. (0. 57 N-m).

10 advancedenergy.com

IMP SERIES (CONTINUED)

171.45

177.8

M4 MOUNTING HOLES (4X)

MARKED AS X

#8-32 MOUNTING HOLES

(4X) MARKED AS Y

M4 MOUNTING HOLES (4X)

IDENTICAL BOTH SIDES

38.10

Normal Air Flow

Reverse Air Flow

iMP8 (1000/1200 Watts Max)

7-Inch Case Size: iMP8: 2.5” x 7” x 10” (63.5 mm x 177.8 mm x 254 mm)

Weight: iMP8 Case: 4.1 lbs. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.

• 750 W Single: 1.6 lbs. 144 W Dual: 0.6 lb.

IMP

Notes:

1. Input: Barri er typ e. Three No. 6-3 2 B.H . screws (0.375” ce nters). Ma x torque: 6 i n-lbs. (0.67 N-m).

2. Contr ol conne ctors: (J1) 10 position housing, g old plated cont acts . Mates wi th Molex 9 0142-0010 housing wi th 90119 -2110 crimp co ntact s (Molex C - Grid III Ser ies) Connector kit include s mating connect or and 10 pins , Astec p art #70 -841-004 . (J 2) 10 positi on housi ng (Landw in 2051P100 0T). Mates with housing 2050S10 00 (Land win) with 2053T 011P (Landwin) pins or JST P HDR-IOV S Housin g and JST S PHD-002T-PO. 5 pins .

3. Cha ssis mat erial: aluminum wi th chemical film c oating (co nducti ve).

4. All dim ensions are in mill imeter s and inch es, and are typic al.

5. Customer mounting -3 s ides M4, bottom also includes 8- 32 mount ing hole s. Max . penet ration i s 0.150” (3.8 mm). Ma x. torque: 5 in-lbs. (0.57 N-m).

6. Outp ut modul e connections : All singl e O/P module s are M4 x 8 mm sc rews. M ax. torq ue: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws . Max. to rque: 5 in-lbs. (0. 57 N-m).

advancedenergy.com 11

IMP

171.45

177.8

19.05

M4 MOUNTING HOLES (4X) MARKED AS X

#8-32 MOUNTING HOLES (4X) MARKED AS Y

M4 MOUNTING HOLES (4X) IDENTICAL BOTH SIDES

38.10

Normal Air Flow

Reverse Air Flow

IMP SERIES (CONTINUED)

iMP1 (1200/1500 Watts Max)

8-Inch Case Size: iMP1: 2.5” x 8” x 11” (63.5 mm x 203.2 mm x 279.4 mm)

Weight: iMP1 Case: 5.0 lb. • 210 W Single: 0.6 lb. • 360 W Single: 1.0 lb.

• 750 W Single: 1.6 lb. • 144 W Dual: 0.6 lb.

Notes:

1. Input: Barri er typ e. Three No. 6-3 2 B.H . screws (0.375” ce nters). Ma x torque: 6 i n-lbs (0. 67 N-m).

3. Cha ssis mat erial: aluminum wi th chemical film c oating (co nducti ve).

4. All dim ensions are in mill imeter s and inch es, and are typic al.

5. Customer mounting -3 s ides M4, bottom also includes 8- 32 mount ing hole s. Max . penet ration i s 0.150” (3.8 mm). Ma x. torque: 5 in-lbs. (0.57 N-m).

6. Outp ut modul e connections : All singl e O/P module s are M4 x 8 mm sc rews. M ax. torq ue: 10 in-lbs. (1.13 N-m). Du al O/P module is M3 x 8 mm scr ews. Ma x. torqu e: 5 in-lbs . (0.57 N -m).

12 advancedenergy.com

OPTIONAL CANBUS OR RS485 INTERFACE

Master/Client Device(s)

Adapter

Output Protocols

Slave/Server Device(s)

Adapter Protocol

Input Protocols

Adapter Command

RS485 using

Modbus

Adapter Controls

CAN using

Modied Modbus

I2C with SMBus

Support

The RS485/CAN-to-I2C uses 2 Input Protocols and 1 Output Protocol. The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified Modus (Command Index: 0x02). The Output Protocol use is: I

C with

SMBus support (Command Index: 0x80).

IMP

RS485/CAN - to - I

For detailed info, download the Software Requirements

Specification (SRS) from http://www.artesyn.com/power/powersupplies/cat/101/Configurable-Power-Supplies-iMP-Series

iMP CAN RS485

advancedenergy.com 13

For international contact information, visit advancedenergy.com.

powersales@aei.com (Sales Support) productsupport.ep@aei.com (Technical Support) +1 888 412 7832

ABOUT ADVANCED ENERGY

Advanced Energy (AE) has devoted more than three decades to perfecting power for its global customers. AE designs and manufactures highly engineered, precision power conversion, measurement and control solutions for mission-critical applications and processes.

Our products enable customer innovation in complex applications for a wide range of industries including semiconductor equipment, industrial, manufacturing, telecommunications, data center computing, and medical. With deep applications know-how and responsive service and support across the globe, we build collaborative partnerships to meet rapid technological developments, propel growth for our customers, and innovate the future of power.

Specifications are subject to change without notice. Not responsible for errors or omissions . ©2020 Advanced Energy Industries, Inc. All rights reser ved. Advanced Energy ®, AE® and Artesyn™ are U.S . trademarks of Advanced Energy Industries, Inc.

ENG-IMP-235-01 12.14

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Artesyn Embedded Technologies: 73-769-001 IMP1-3Q0-3W0-00-A

Advanced Energy ARTESYN INTELLIGENT MP User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual