For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
SLOT 1 NET/D BU
WAN-T1 DSX-1 DBU
WAN-DDS DBU
PECIFICATIONS
S
NETVANTA ISDN BRI DIAL BACKUP INTERFACE MODULE (DIM) P/N 1200865L1
LAN
CONSOLE
12 VDC
POWER
Clear channel and Bonding mode 1 call protocols
Network support for 64 kbps (1 B-channel) or 128 kbps (2 Bchannels)
D-channel switch compatibility with AT&T 5ESS, Northern
Telecom DMS-100, and National ISDN-1
V.54 network loopback support
INSTALLATION INSTRUCTIONS (CONTINUED)
4. Slide the NIM with the ISDN BRI DIM attached into the
NetVanta option slot until the NIM is firmly seated against
the back of the chassis.
5. Secure the pins at both edges of the NIM.
6. Connect the cables to the associated device(s)
7. Complete installation of the base unit.
8. Restore power to the base unit.
ISDN DBU (RJ-48C) CONNECTION PINOUT
Pin Name Description
1-3 — Unused
4 R Network-Ring
5 T Network-Tip
6-8 — Unused
INSTALLATION INSTRUCTIONS
1. Remove power from the base unit.
2. If the Network Interface Module (NIM) is already in the
NetVanta chassis, release the pins at both edges of the
NIM faceplate and slide the module out of the chassis.
3. Carefully align the P1 connector on the NIM with the J1
connector on the ISDN BRI DIM. Using only fingertip
pressure so that neither circuit board bends or flexes,
ensure that the connectors are firmly seated. Secure the
ISDN BRI DIM to the NIM using the screws and standoff
posts supplied.
Quick Start Guide, 61200865L1-13B, February 2004 Technical Support 1-888-4ADTRAN (1-888-423-8726) 2004 ADTRAN, All Rights Reserved
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
ISDN BRI DIM C
alias <text>
Comment line to provide the text name assigned by the SNMP network management system.
bonding txadd-timer <seconds>
Specifies the aggregate call connection timeout.
bonding txcid-timer <seconds>
Specifies the bearer channel (B-channel) negotiation timeout.
bonding txdeq-timer <seconds>
Specifies the network delay equalization timeout.
bonding txfa-timer <seconds>
Specifies the frame pattern detection timeout.
bonding txinit-timer <seconds>
Specifies the originating endpoint negotiation timeout.
bonding txnull-timer <seconds>
Specifies the answering endpoint negotiation timeout.
caller-id override always <number>
Forces a replacement of the incoming caller ID number with the number given. The received
caller ID, if any, is discarded, and the given override number is used to connect the incoming
call to a circuit of the same number. Use no caller-id override (default) to disable any caller ID
overrides.
NETVANTA ISDN BRI DIAL BACKUP INTERFACE MODULE (DIM) P/N 1200865L1
OMMANDS
description <text>
Comment line to provide an identifier for this interface (for example, circuit ID, contact
information, etc.).
<text> Up to 80 alphanumeric characters
isdn spid1 <spid string> <LDN>
Programs the first Service Profile Identifier (SPID) and Local Directory Number (LDN) for the
Basic Rate ISDN (BRI) interface.
This information should be supplied by your service provider.
<spid string>
<LDN>
isdn spid2 <spid string> <LDN>
See isdn spid1.
shutdown
Turns off the interface. The no version of this command turns the interface on and allows it to
pass data.
switch-type {basic-5ess | basic-dms | basic-ni}
Specifies the signaling type configured on the BRI interface. The type of ISDN signaling
implemented on the BRI interface does not always match the manufacturer of the CO switch.
This setting is determined by your service provider.
basic-5ess Lucent/AT&T 5ESS signaling
basic-dms Nortel DMS-100 (non SL-1 version) signaling
basic-ni National-ISDN 1 signaling
Number string (usually ending in a 01 or 02 sequence) registered by
the terminal adapter for identification.
Number string representing the phone number associated with the
BRI interface.
caller-id override if-no-CID <number>
Allows a replacement of the received caller ID number, but only if there is no caller ID available
on the incoming call. The received caller ID, if available, is used to connect the call. However,
if no caller ID is received, the given override number is used to connect the incoming call to a
circuit of the same number.
Quick Start Guide, 61200865L1-13B, February 2004 Technical Support 1-888-4ADTRAN (1-888-423-8726) 2004 ADTRAN, All Rights Reserved
Loading...