ADTRAN Atlas 830 User Manual

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

Reviewing the Front Panel

ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC)

Network Ports LEDs

Controller LEDs

NE TW O RK

TEST

ERROR

ALARM

TEST

ERROR

ALARM

STATUS

ONLINE

TEST

ACO Switch

POWER

SYSTEM

ETHERNET

REMOTE

ACO

CRAFT

Craft Interface

Connecting to the ATLAS 830

Connecting a VT100 terminal (or VT100 terminal emulator) to the C interface (on the front panel of the unit) or the A

interface (on the rear panel

DMIN

of the unit) allows access to the terminal menus and management features of the ATLAS 830.

Perform Steps Below in the Order Listed:

1. Configure a VT100 terminal (or terminal emulation software) with the following settings:

Data Rate: 9600 baud Stop Bits: 1 Data Bits: 8 Flow Control: None Parity Bits: None

If the terminal has a parallel setting, disable it and use serial.

2. Connect the DB-9 male end of the data cable into the ATLAS 830 C

port. Make the connection to the VT100 terminal as appropriate for

DMIN

your connection.

RAFT

Option Module LEDs

MODULES

ATLAS 830

Craft Pinout

PIN NAME DESCRIPTION

1, 4, 6-9 N/A Not Connected

2 RD Receive Data (output) 3 TD Transmit Data (input) 5 SG Signal Ground

System Status LEDs

The System Status LEDs display the status of the power supply, controller, and other system parameters for the ATLAS 830. For a more detailed discussion of the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS 830 System Manual.

LED Description

Power Indicates the status of the power supply

System Indicates the status of the unit controller and other system parameters.

Ethernet Indicates the status of the ethernet port.

Remote Indicates whether a user (Telnet or VT100) is logged in to the unit.

3. Initiate a terminal session and the L

screen displays. The default

OGIN

password is password. (Passwords in the ATLAS 830 are case sensitive.)

For more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC)

Reviewing the Rear Panel Design

Alarm Relay Connection

Admin Interface

Admin Pinout

PIN NAME DESCRIPTION

1 DCD Data Carrier Detect (output) 2 RD Receive Data (output) 3 TD Transmit Data (input) 4 DTR Data Terminal Ready (input) 5 SG Signal Ground 6 DSR Data Set Ready (output) -- not connected 7 RTS Request to Send (input) 8 CTS Clear to Send (output) 9 RI Ring Indicate (output) -- not connected

10/100BaseT Ethernet Pinout

PIN NAME DESCRIPTION

1 TX1 Transmit Positive 2 TX2 Transmit Negative 3 RX1 Receive Positive

4,5 — Unused

6 RX2 Receive Negative

7, 8 — Unused

T1/PRI Monitor Jacks

Option Module Slots

Network T1/PRI Ports

Optional DC Power Supply P/N 1200229L1

CAUTION: FOR CONTINUED PROTECTION

AGAINST RISK OF FIRE, REPLACE

ONLY WITH SAME TYPE AND RATING

OF FUSE.

OFF

12A/125V

48 VDC, 6A

USE COPPER

CONDUCTORS ONLY

SEE MANUAL BEFORE

REMOVING POWER SUPPLY

Power Supply Slot

Alarm Relay Connection Pinout

PIN NAME DESCRIPTION

1 Normaly Closed (NC) Opens when a selected alarm condition is present. 2 Normally Open (NO) Closes when a selected alarm condition is present. 3 Common (COM) Common connection between external circuitry

and NC or NO terminal.

4 Chassis Ground (GND)

DC Power Supply Connection (Optional P/N 1200229L1)

PIN NAME DESCRIPTION

1 + Ground (GND) 2--48VDC