ADTRAN AGENT CARD OPTION MODULE INSTALLATION INSTRUCTIONS

AGENT CARD OPTION MODULE P/N 1200160L1HS

NSTALLATION INSTRUCTIONS

Caution: Turn off the power to unit before installing the Agent Card.

1. Remove the cover plate from the o p tio n slot in t he TSU r ear panel.

2. Slide the Agent Card into the option slot until the module is firmly positioned against the front of the chassis.

3. Fasten the thumbscrews at both edges of the module. Tighten with a screwdriver.

4. Install Agent/TSU jumper cab le betwe en the Chai n- out co nne ctor on the Agent Card and the Chain-in connector on the TSU.

For more detailed documentation, visit us online at www.adtran.com

PECIFICATIONS

10BASET INTERFACE Interface Complies with IE EE 80 2.3 Rate 10 megabits per second (Mbps) Connector RJ-45 (AT&T 258A) connector Indicators Trans mit, rec eive, li nk statu s, centr al proc essing u nit

(CPU) access (via front panel)

Receiver Accepts signal > 300 millivolt (mV) Protocols Network: IP

Transport: TCP, UDP Service: SNMP, Telnet, ICMP, ARP, PING, T-Watch

SLIP/EIA-232 INTERFACE Interface EIA-232 physical int er fac e Rates 1200, 2400, 4800, 9600, 19200, 38400 bits per

second (bps)

Signals RD, TD, CTS, RTS, DCD, RI, DTR Pinout DCE Connector RJ-45 conne ctor Protocols Network: IP

Transport: TCP, UDP Service: SNMP, Telnet, ICMP, ARP, PING, T-Watch

CHAIN-OUT INTERFACE Interface EIA-232 physical int er fac e (TSU-X 00 cha in -o ut

interface)

5. Install additional jumpers between the unit chain-in and chain-out ports to manage other units by the Agent Card.

Rates 1200, 2400, 9600, 19200, 38400 bps Connector RJ-45 (AT&T 258A) connector Signals RXD, TXD Pinout DTE Connector RJ-45 Protocols Link: ADLP

Service: T-Watch, ATEL

AGENT CARD OPTION MODULE P/N 1200160L1HS

ENU TREE

ERMINAL MODE/TELNET MENU

1) Host Menu Access 1) Add New Unit 1) SNMP Read Community

2) Remote Menu Access 2) Modify Unit 2) SNMP Read/Write Community

3) Unit Access Table 3) Delete Unit 3) SNMP Trap Community

4) Default Unit Passcode 4) Host 1 Trap IP Addr. Agent Card 5) Exit 5) Host 2 Trap IP Addr Main Menu 6) Host 3 Trap IP Addr

7) Host 4 Trap IP Addr

4) Management Configuration 8) System Name

9) System Contact

1) TCP/IP Interface 10) System Location

2) Agent IP Address 11) Auth. Fail Traps Sent

3) Agent Subnet Mask 12) Poll Link Status Traps Sent

5) TCP/IP Configuration 4) Default IP Router 13) Ping IP Host

5) Telnet/Terminal Timeout 14) Exit

6) Telnet/Terminal Password

7) Exit

1) Rate

6) RS-232 Configuration 2) Flow Control

ETWORK CONNECTION PINOUTS

EIA-232 CONNECTOR PINOUT

Pin Name Description

1 GND Signal Ground 2 RTS Request to Send (Input) 3 TD Transmit Data (Input) 4 DTR Data Terminal Ready (Output) 5 RD Receive Data (Output) 6 CD Carrier Detec t (Input) 7 RI Ring Indicate (Inpu t) 8 CTS Clear to Send (Output)

CHAIN-OUT CONNECTOR PINOUT Pin Name Description

1 Ground Signal Ground 2UnusedN/A 3 TD Transmit Data (Input) 4UnusedN/A 5 RD Receive Data (Output)

RONT PANEL MENUS

1) Port Status 1) 10Base-T

2) RS-232 Front Panel Port Config 1) IP Interface 3) Chain Port Menu 2) IP Address 4) Flash Download

3) Subnet Mask

4) Default Router

5) RS-232 Rate 1) SW Revision

6) RS-232 Flow CTL 2) Enet Address

3) Port Util 3) CMD Mode

4) Port Test

6, 7, 8 Unused N/A

10BASET ETHERNET PINOUT Pin Name Description

1TX1 2TX2 3RX1 4, 5 Un used N/A 6RX2 7, 8 Un used N/A