ADTRAN 3192 H2TU-C, 220 DDM User Manual

220/DDM+/3192 H2TU-C

Option Settings Display (“VIEW”)

Message Description Settings Default

LBO Line Build Out EXT, 0, 133, 266, 399, 533 * CODE Line Code AMI, B8ZS B8ZS FRMG DSX-1 Framing AUTO, UNF UNF NLBK NIU Loopback EN, DIS EN LBTO Loopback Timeout NONE, 1 Hr, 2 Hr, 8 Hr, 24 Hr 1 Hr

CLOS Customer Loss Response AIS, LPBK AIS PRM Performance Reporting Messages NPRM, SPRM, NONE, AUTO AUTO TXLV DS1 Transmit Level 0 dB, -7.5 dB, -15 dB 0 dB

SPWR Span Power EN, DIS EN

ALMP Alarm Pattern to Customer AIS, LOS AIS

* 220 = EXT, 3192/DDM+ = 0

Loopback Options Display (“LPBK”)

Select Loopback State Loopback Description

HTUC NET Network loopback at H2TU-C

CST Customer loopback at H2TU-C NONE No active loopback

HTUR BLB Bidirectional loopback at H2TU-R

NET Network loopback at H2TU-R CST Customer loopback at H2TU-R NONE No active loopback

DSX-1 BANTAM JACKS

■ Provides an intrusive access point to the data stream.

TX - Access the data stream being received from the network.

RX - Access the data stream being transmitted to the network.

MON

■ Provides a non-intrusive access point to the data stream.

TX - Monitors the data stream being received from the network

RX - Monitors the data stream being transmitted to the network.

NOTE: The DDM+ H2TU-C does not have the DSX-1 Bantam Jacks option.

RS-232 DB-9 CONNECTOR

■ Used to access performance monitoring data, perform loopbacks and provision units via VT100

emulation applications such as Hyper Terminal – Private Edition, ProComm Plus, and Telnet.

■ There are two types of terminal emulation modes, Manual and Real-Time. Use “CTRL-T” to toggle

between the two modes.

Manual Emulation Mode

: Press the space bar 3 times to manually update the screen. Print screen

and log file commands are available in this mode.

Real-Time Emulation Mode

: The default mode. Print screen and log file commands are not

available in this mode. Cursor placement and screen highlighting are enabled.

■ Provision terminal port as follows:

Data Rate — 1.2 to 19.2 kbps Asynchronous Data Format — eight data bits, no parity (none), one stop bit

■ When using a PC with terminal software, be sure to disable any power saving programs.

PROVISIONING NOTES

■ This unit can be provisioned via the RS-232 port or remotely via ITS codes. This unit cannot be

provisioned from the faceplate four-character display. Select “2” from the ADTRAN HDSL2 Main

Menu Screen to view the Provisioning Screen.

STATUS LED

STATUS ● GREEN Everything functioning normally

✷ BLINKING ES, SES, or BPV detected

● YELLOW Loopbacks active

✷ BLINKING In-band loopbacks armed

● RED Alarm on the HDSL2 loop, DSX or DS1 interface

✷ BLINKING Signal Quality of 0 or No Sync on the HDSL2 loop

FOUR-CHARACTER DISPLAY (FCD) OPERATION

FCD Modes

Mode Message Function

Status STAT Displays loop margin, alarms, and general status conditions Display Off Blank Blank after five minutes of no activity View VIEW View current options settings Loopback LPBK Select and execute HDSL2 circuit loopbacks

Status/Alarm Display (“STAT”)

Message Description

MARG xx HDSL2 loop margin, 0-20 DSL ERR CRC error detected on HDSL2 Loop LOC ERR Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode)

detected locally at DSX-1 of the H2TU-C

REM ERR Frame bit error (SF Mode), Bipolar Violation (BPV), or CRC error (ESF Mode)

detected remotely at DS1 of the H2TU-R DSL LOS No synchronization of H2TU-C and H2TU-R on loop LOC LOS DSX signal is absent from the network interface or is of a format which does

not match the provisioning of the HDSL2 circuit REM LOS DS1 signal is absent from the network interface or is of a format which does

not match the provisioning of the HDSL2 circuit ARM NIU Loopback is armed

Left = MODE

Center = OFF

Right = SELECT

C A U T I O N

COMPLIANCE CODES

This product is intended for installation in restricted access locations only and in equipment with a Type “B” or “E” installation code.

Input current at maximum load is 0.7 A at –48 Vdc. Maximum output at over current condition is 165 mA at –190 Vdc.

WARRANTY

Warranty for Carrier Networks products manufactured by ADTRAN and supplied under Buyer’s order for use in the U.S. is ten (10) years. For a complete copy of ADTRAN’s U.S. Carrier Networks Equipment Warranty: (877) 457-5007, Document #414.

CODE IN OUT

Installation Code (IC) A – Telecommunication Code (TC) – X

Power Code (PC) F C

Reference Guide

61221001L6A-30B

0011

1221001L6

STATUS

HIS

D S X

R S 2 3 2

C A U T I O N

SUBJECT TO ELECTROSTATIC DAMAGE

OR DECREASE IN RELIABILITY.

HANDLING PRECAUTIONS REQUIRED.

D S L

SELMODE

M O N

E Q

PRICING AND AVAILABILITY 800.827.0807

TECHNICAL SUPPORT 800.726.8663

RETURN FOR REPAIR 256.963.8722

www.adtran.com

61221001L6-30B

HDSL2 TROUBLESHOOTING GUIDE

HDSL2 DEPLOYMENT GUIDELINES

■ Cable pairs must be non-loaded

■ Total bridged tap length < 2.5 kft

■ No single bridged tap >2 kft

■ 196 kHz insertion loss < 35 dB

■ Pulse attenuation (ATTEN on HDSL2 Span Status Screen) < 30 dB

■ Maximum loop resistance is 900 Ω

■ Impulse noise < 50 dBrn as measured using a 50 kb filter

■ Wideband noise ≤ 31 dBrn as measured using a 50 kb filter

TURN UP GUIDELINES

Circuit Parameters Under Normal Operation

■ Margin ≥ 6 dB

■ Attenuation < 30 dB

■ Insertion Loss ≤ 35 dB

■ No ES, SES, or UAS

If these parameters are met, then the circuit will provide quality service. If not, a cable problem or excessive loss situation is probable. In this case, a more detailed cable analysis is required to insure that all HDSL2 Loop Specifications are met.

These conditions may also be the result of intermittent cable faults or intermittent noise impairments. If intermittent problems are suspected, utilize the Performance History Screen (Main Menu selection #5) to assist in troubleshooting. An example of a Performance History Screen is illustrated in the bottom righthand corner.

Front Panel Indications Under Normal Operation

■ STATUS LED will be Green (solid)

NOTE: The circuit must have DSX-1 signal (from Network) and DS1 signal (from Customer) in order for the LED to be Green. If either DSX-1 or DS1 signal is not present, the LED will be Red.

■ The four-character display will flash the current loop margin for the HDSL2 loop. No alarm or error mes-

sages will be displayed. After five minutes of no activity, the display will turn completely Off. It will remain Off until MODE or SELECT is activated or a message other than loop margin is to be displayed.

TROUBLESHOOTING GUIDELINES

Front Panel Indicators

■ All indicators are Off. 1. Verify that -48 Vdc is properly connected.

2. Inspect fuse and verify that it is not blown.

3. Insert the H2TU-C into a slot known to be good and verify that the STATUS indicator is lit. If card fails replace H2TU-C.

■ Status LED is Blinking Red Poor signal quality or loss of sync. Use basic troubleshooting procedures to

identify cable pair problems.

■ Status LED is Solid Red If customer equipment is not installed, initiate an H2TU-R to Network

Loopback and perform BERT test. If this test fails, or the craft interface indicates a loss of sync, then there is a problem with the cable pair that should be resolved through normal troubleshooting procedures.

■ Status LED is Blinking Green Errors are being taken on the DSX, DS1, or HDSL2 loop. The craft interface

screens will identify the source. BERT test to the appropriate loopbacks should isolate the problem.

Four Character Display

■ The error messages for this display are defined on page 1 of this guide.

Craft Interface Screens

■ Detailed Status Screen Provides instant view of system status (Main Menu selection “3”, Span Status selection “2”)

■ Alarm History Screen Provides a record of system alarms (Main Menu selection “8”)

■ Event History Screen Provides last 100 events on the system (Main Menu selection “9”)

■ Performance History Screens Provide performance data for all points in the system (Main Menu selection “5”)

■ For complete Installation and Maintenance: (877) 457-5007, Document #529,

#555, and #556. Please have your fax number available. ■