ADTRAN 234 User Manual

or more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

NET ETH

CONNECT THE CONSOLE INTERFACE

Before connecting to the Total Access 234 console interface, you will need the following items: VT100 terminal or PC (with VT100 terminal emulation software) and a straight through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal (or PC) on the other.

1. Connect the DB-9 (male) connector of your serial cable to the console port on the rear panel of the unit.

2. Connect the loose end of the serial cable to the VT100 terminal or PC (with terminal emulation software).

3. Open a VT100 terminal session to the Total Access 234 using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the ADTRAN Command Line Interface (CLI).

SPECIFICATIONS

TOTAL ACCESS 234 SHDSL NTU P/N 1200708L1

CONFIGURE GATEWAY IP ADDRESSES/SUBNET MASK

Configure the Gateway IP addresses and subnet mask by following these steps. If you are not sure what IP address to assign, please contact your network administrator.

1. Enter enable to activate the Enable command security mode.

2. When prompted, enter the enable password (if configured).

3. Enter config terminal to activate the Global configuration mode.

4. Enter bre lan-gw 10.26.12.12

255.255.255.0

* to assign LAN and WAN Gateway IP addresses

and subnet mask.

*Note: Underlined text represents example entries only. Modify them to match your configuration.

wan-gw 100.26.12.12 mask

5. Enter exit to return to the Enable configuration mode.

DC Input Power 12 VDC nominal (8.5 VDC min, 18 VDC max); ITU-T standards: G.991.2

Diagnostics & Test Self-diagnosis; local loopback; remote loopback

EMC Emissions EN55022:1998 Class B; FCC Part 15 Class B

EMC Immunity, Power Fault, and Lightning

Electrical Safety EN60950; AS/NZS 60950; UL60950 3rd ed.;

Telecom S043.2; G.991.2

Environmental

*Note: No stacking should be done at 50

Dimensions 9.3 inches W x 2.1 inches H x 6.1 inches D

Connectors SHDSL Port: RJ-45; 135 ohms; TNV-3 rated

EN55024:1998; EN61000-3-2; EN61000-3-3; Telstra 1563; K.21 (2004) Enhanced

CSA C22.2 No. 60950 3rd ed.; IEC 60950 CB Scheme

Operating Temp: 0

Humidity: 95 percent noncondensing

10/100BaseT Ethernet: RJ-45

Console Port: DB-9 female

Power Input: Kycon KPJ-3S snap & lock or equivalent

C to 50oC; Storage Temp: -20oC to 70oC

C. Up to three units can be stacked at room temperature.

6. Enter copy running-config startup-config to save the running configuration to the unit’s non-volatile memory (NVRAM).

FEATURES

• One integrated EIA-232 configuration port (DCE)

• One integrated 10/100BaseT Ethernet port

• 2-Wire/4-Wire SHDSL interface

• WAN Protocol: ATM

• Command Line Interface (CLI)

• Management - EOC/CLI using Virtual Terminal

• Front panel LEDs

• Wall mounting available with additional parts

Table standoff cannot be used with this unit.

or more detailed documentation, visit us online at www.adtran.com

Quick Start Guide

TOTAL ACCESS 234 SHDSL NTU P/N 1200708L1

TOTAL ACCESS 234 LEDS

LED Color Indication

PWR Off

Green (solid)

SHDSL Off

Green (solid)

Yellow (solid)

Red (solid)

LLOOP Off

Red (solid)

RLOOP Off

Red (solid) BERT -- Not applicable with this product. LNK Off

Green (solid)

Yellow (solid) TD Off

Green (blinking) RD Off

Green (blinking)

No power present.

Power present. Unit is powered off.

Port is trained with no active alarm conditions.

Port is trained with minor active alarm condition.

Port is attempting to train or is trained with a major alarm condition.

No local loop is active.

A local loop is active. No remote loop is active.

A remote loop is active.

No Ethernet link present.

The 10BaseT Ethernet link is up.

The 100BaseT Ethernet link is up. No transmit activity on Ethernet port.

Transmit activity on Ethernet port. No receive activity on Ethernet port.

Receive activity on Ethernet port.

10/100BASET ETHERNET PORT PINOUT

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4,5 — Unused

6 RX2 Receive Negative

7,8 — Unused

CONSOLE PORT PINOUT

Pin Name Description

1 DCD Data Carrier Detect (output)

2 RD Receive Data (output)

3 TD Transmit Data (input)

4 DTR Data Terminal Ready (input)

5 SG Signal Ground

6 DSR Data Set Ready Tied to pin 1 (output)

7, 9 — Unused

8 CTS Clear to Send Tied to pin 1 (output)

WAN-SHDSL NETWORK PINOUT (RJ-45)

Pin Name Description

1 Tip 2 4-wire Loop 2 Pair Tip

2 Ring 2 4-wire Loop 2 Pair Ring

3 — Not connected

4 Tip 1 2-wire Pair Tip,

4-wire Loop 1 Pair Ring

5 Ring 1 2-wire Pair Ring,

4-wire Loop 1 Pair Ring

6-8 — Unused