ADTRAN 1224 User Manual

NetVanta 1224 Series Switches

Quick Start Guide

NETVANTA 1224 FRONT PANEL LAYOUT

NETVANTA 1224ST FRONT PANEL LAYOUT

NETVANTA 1224R FRONT PANEL LAYOUT

NETVANTA 1224STR FRONT PANEL LAYOUT

NETVANTA 1224 AND 1224ST REAR PANEL LAYOUT

NETVANTA 1224R AND 1224STR (AC VERSION) REAR PANEL LAYOUT

USE COPPER

CONDUCTORS ONLY

-48V....., 1.2A

+24V....., 2.5A

For more detailed documentation, visit us online at www.adtran.com.

P/N 1200500L1/1200504L1/1200510L1/

1200520L1/1200590L1

GETTING STARTED

Two configuration methods are available for your NetVanta switch:

• Web-based GUI

• AOS Command Line Interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.

ACCESS THE GUI

You may access the web-based GUI from any web browser on your network by following these steps:

1. Connect the switch to your PC using any of the 24 Ethernet ports on the front of the unit.

2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for instructions.)

3. Enter the unit’s IP address in your browser address line. The default IP address is

10.10.10.1.

4. You will then be prompted for the username and password (the default settings are admin and password).

5. The initial GUI screen appears.

ACCESS THE CLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the NetVanta switch CONSOLE port, you need the following items:

• VT100 terminal or PC (with VT100 terminal emulation software)

• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear

panel of the unit.

2. Connect the other end of the serial cable to the terminal or PC.

3. Provide power to the unit as appropriate. Refer to the NetVanta 1000 and NetVanta 1000R Series Hardware Installation Guide (provided on the ADTRAN OS System Documentation CD) for more details.

4. Once the unit is powered up, open a VT100 terminal session using the following settings: 9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the AOS CLI.

5. Enter enable at the > prompt.

6. Enter the enable password when prompted. The default password is password.

The configuration parameters used in the examples outlined in this

NETVANTA 1224STR (DC VERSION) REAR PANEL LAYOUT

document are for instructional purposes only. Please replace all underlined entries (

example) with your specific parameters to configure

your application.

Quick Start Guide

NetVanta 1224 Series Switches

For more detailed documentation, visit us online at www.adtran.com.

P/N 1200500L1/1200504L1/1200510L1/

1200520L1/1200590L1

CONFIGURE THE UNIT’S IP ADDRESS

The following steps create an IP address and subnet mask for the virtual interface vlan 1. If you are not sure what IP address to assign, please contact your network administrator.

1. At the # prompt, enter config terminal.

2. At the (config)# prompt, enter interface vlan 1 to access the configuration parameters for the

virtual LAN (VLAN) interface.

3. Enter ip address 10.26.12.12

using a 24-bit subnet mask.

4. Enter no shutdown to activate the virtual interface to pass data.

5. Enter exit to return to the Global Configuration mode.

255.255.255.0 to assign an IP address to the VLAN interface

Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. If IP routing is enabled on the unit, do NOT set a default gateway.

ENABLE TELNET ACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password.

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3. Enter login to initiate Telnet access.

4. Enter password adtran

5. Enter exit to return to the Global Configuration mode.

6. Verify that the prompt of your unit displays (config)#.

7. Enter do write memory to save the current configuration.

to change the login password for the Telnet sessions.

ETHERNET PINOUTS

CONSOLE PINOUTS

Pin Name Description

1 DCD Data Carrier Detect (output)

2 RD Receive Data (output)

3 TD Transmit Data (input)

4 DTR Data Terminal Ready (input)

5 SG Signal Ground

6 DSR Data Set Ready (output)

7 — Unused

8 CTS Clear to Send (output)

9 — Unused

For information on installing the VPN Accelerator Card, please refer to the

NetVanta 1000 Series Hardware Installation Guide on the ADTRAN OS System Documentation CD included in your switch shipment.

CONFIGURE YOUR APPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS System Documentation CD included in your shipment. For more detail on hardware setup, refer to

the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference Guide, configuration guides, and technical support notes.

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4, 5 — Unused

6 RX2 Receive Negative

7, 8 — Unused

Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com.