Page 1
ULTRA HEX BAR 6
©2013 ADJ Products, LLC all rights reserved. Information,
specications, diagrams, images, and instructions herein are
subject to change without notice. ADJ Products, LLC logo and
identifying product names and numbers herein are trademarks
of ADJ Products, LLC. Copyright protection claimed includes all
forms and matters of copyrightable materials and information
now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or
registered trademarks of their respective companies and are
hereby acknowledged. All non-ADJ Products, LLC brands and
product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property, equipment, building, and
electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result
of the improper, unsafe, unsucient and negligent assembly,
installation, rigging, and operation of this product.
7/14
User Instructions
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment.
Please turn o all electrical products when they are not in use. To
avoid power consumption in idle mode, disconnect all electrical
equipment from power when not in use. Thank you!
Page 2
Ultra Hex Bar 6 Introduction
Ultra Hex Bar 6 Features
Unpacking: Thank you for purchasing the Ultra Hex Bar 6 by ADJ
Products, LLC. Every Ultra Hex Bar 6 has been thoroughly tested and
has been shipped in perfect operating condition. Carefully check the
shipping carton for damage that may have occurred during shipping.
If the carton appears to be damaged, carefully inspect your xture for
any damage and be sure all accessories necessary to operate the unit
has arrived intact. In the case damage has been found or parts are
missing, please contact our toll free customer support number for further instructions. Do not return this unit to your dealer without rst contacting customer support.
Introduction: The Ultra Hex Bar 6 is a DMX intelligent, LED bar fixture. This xture can be used in a stand alone mode or connected in a
Master/Slave conguration. This par has six operating modes: Sound
Active mode, Auto mode, Program mode, RGBWA + UV dimmer mode,
Static Color mode, and DMX control mode.
Customer Support: ADJ Products, LLC provides a customer support
line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m.
Pacic Standard Time.
Voice: (800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
Warning! To prevent or reduce the risk of electrical shock or re, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
• Multi-Colors
• Six Operating Modes
• Electronic Dimming 0-100%
• Built in Microphone
• DMX-512 protocol
• 3-Pin DMX Connection
• 5 DMX Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel
Mode, 12 Channel Mode, & 18 Channel Mode.
• ADJ RFC compatiable (Sold Separately)
• Power Cord Daisy Chain (See page 21)
Ultra Hex Bar 6 Warranty Registration
The Ultra Hex Bar 6 carries a 2 year limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight pre-paid
and accompany a return authorization (R.A.) number. The R.A. number
must be clearly written on the outside of the return package. A brief
description of the problem as well as the R.A. number must also be
written down on a piece of paper included in the shipping carton. If
the unit is under warranty, you must provide a copy of your proof of
purchase invoice. You may obtain a R.A. number by contacting our
customer support team on our customer support number. All packages returned to the service department not displaying a R.A. number
on the outside of the package will be returned to the shipper.
Ultra Hex Bar 6 Installation
The unit should be mounted using a mounting clamp (not provided),
axing it to the mounting bracket that is provided with the unit.
Always ensure that the unit is rmly xed to avoid vibration and slipping while operating. Always ensure that the structure to which you
are attaching the unit is secure and is able to support a weight of 10
times the unit’s weight. Also, always use a safety cable that can hold
12 times the weight of the unit when installing the xture.
The equipment must be installed by a professional, and it must be
installed in a place where it is out of the reach of people’s grasp.
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 2
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 3
Page 3
Ultra Hex Bar 6 Safety Precautions
Ultra Hex Bar 6 Set Up
• To reduce the risk of electrical shock or re, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break o the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and re in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 21 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 4
Power Supply: The ADJ Ultra Hex Bar 6 contains a automatic volt-
age switch, which will auto sense the voltage when it is plugged into
the power source. With this switch there is no need to worry about the
correct power voltage, this unit can be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
tocol used as a form of communication between intelligent fixtures
and controllers. A DMX controller sends DMX data instructions from
the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA
“OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of
dierent manufactures to be linked together and operate from a single
controller, as long as all xtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using several
DMX fixtures try to use the shortest cable path possible. The order
in which fixtures are connected in a DMX line does not influence the
DMX addressing. For example; a fixture assigned a DMX address of 1
may be placed anywhere in a DMX line, at the beginning, at the end,
or anywhere in the middle. When a fixture is assigned a DMX address
of 1, the DMX controller knows to send DATA assigned to address 1
to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation):
The Ultra Hex Bar 6 can be controlled via DMX protocol. The Ultra Hex
Bar 6 has 5 DMX channel modes, please see pages 7-8 for the dierent
modes. Your unit and your DMX controller require a standard 3-pin XLR
connector for data input and data output (Figure
1). We recommend Accu-Cable DMX cables.
If you are making your own cables, be sure to
use standard 110-120 Ohm shielded cable (This
cable may be purchased at almost all pro lighting
stores). Your cables should be made with a male
and female XLR connector on either end of the
cable. Also remember that DMX cable must be
daisy chained and cannot be split.
Figure 1
Notice: Be sure to follow gures two and three when making your own
cables. Do not use the ground lug on the XLR connector. Do not con-
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 5
Page 4
Ultra Hex Bar 6 Set Up
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
DMX512
DMX+,DMX-,COMMON
1
2
3
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
POWER
SOUND
REMOTE
CONTROL
INPUT
POWER
INPUT OUTPUT
Ultra Hex Bar 6 Operating Instructions
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX512 OUT
3-PIN XLR
1
3
2
DMX +
DMX -
3
1
2
DMX512 IN
3-PIN XLR
Figure 2
XLR Male Socket
1 Ground
2 Cold
3 Hot
XLR Female Socket
2 Cold
1 Ground
3 Hot
XLR Pin Conguration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
Pin 3 = Data True (positive)
Figure 3
Special Note: Line Termination.
When longer runs of cable are
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ Products, LLC part number Z-DMX/T) will decrease the possibilities of erratic behavior.
Termination reduces signal errors and
1
avoids signal transmission problems
3
and interference. It is always advisable
2
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
5-Pin XLR DMX Connectors.
and PIN 3 (DMX +) of the last fixture.
Some manufactures use 5-pin DMX-
Figure 4
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
xtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)
Ground/Shield
Data Compliment (- signal)
Data True (+ signal)
Not Used
Not Used
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 6
Pin 1
Pin 2
Pin 3
Pin 1
Pin 2
Pin 3
Do Not Use
Do Not Use
Menu Lock:
You can set the menu to lock after 30 seconds. When the menu is set
to lock, press and hold the MODE button for at least 5 seconds to
unlock and access the menu.
To set the menu to lock after 30 seconds, press the MODE button until “OTHER” is displayed. Press the SET UP button so that
LOCK:XXX” is displayed. “XXX” represents either ON or OFF. Press
the UP or DOWN buttons so that ON is displayed. Now the menu will
lock after 30s.
LED Display On/Off:
To set the LED display light to turn off after 30 seconds, press the
MODE button until “OTHER” is displayed. Press the SET UP button
so that BLGT:XXX” is displayed. “XXX” represents either ON or OFF.
Press the UP or DOWN buttons so that OFF is displayed. Now the
display light will turn off after 30s. Press any button to turn the dis-
play on again.
Operating Modes:
The Ultra Hex Bar 6 has six operating modes:
• DMX control mode - This function will allow you to control each
individual fixtures traits with a standard DMX 512 controller.
• RGBWA + UV Mode - Choose one of the six colors to remain static
or adjust the intensity of each color to make your own color.
• Sound-Active mode - The unit will react to sound, chasing through
the built in programs. There are 16 sound active modes.
• Program Mode - The unit will run 1 of 20 built-in programs.
• Auto Mode - The unit will run a auto program.
• Static Color Mode - There are 63 colors to choose from.
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Ultra
Hex Bar 6 has 5 DMX modes: 6 Channel mode, 7 Channel mode, 8
Channel mode, 12 Channel mode, and 18 Channel mode. See pages
15-19 for each mode’s DMX traits.
1. This function will allow you to control each individual fixture’s
traits with a standard DMX 512 controller.
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 7
Page 5
Ultra Hex Bar 6 Operating Instructions
Ultra Hex Bar 6 Operating Instructions
2. To run your fixture in DMX mode press the MODE button until
“DMX MODE: is displayed. Press the SET UP button so that
ADDR:XXX” is displayed. “XXX” represents the current displayed
address. Use the UP or DOWN buttons to select your desired
DMX address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
• To run the 6 Channel Mode, press the MODE button until
“CHAN:6” is displayed. This is the 6 Channel DMX Mode.
• To run the 7 Channel Mode, press the MODE button until
“CHAN:7” is displayed. This is the 7 Channel DMX Mode.
• To run the 8 Channel Mode, press the MODE button until
“CHAN:8” is displayed. This is the 8 Channel DMX Mode.
• To run the 12 Channel Mode, press the MODE button until
“CHAN:12” is displayed. This is the 12 Channel DMX Mode.
• To run the 18 Channel Mode, press the MODE button until
“CHAN:18” is displayed. This is the 18 Channel DMX Mode.
4. Please see pages 15-19 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
RGBWA & UVDimmer Mode:
1. Plug the fixture in and press the MODE button until “MANUAL” is
displayed.
2. When “RED: XXX” is displayed you are in Red dimming mode.
Press the UP and DOWN buttons to adjust intensity. After you
have finished adjusting the intensity, or if you would like to skip to
the next color, press the SET UP button.
3. When “GREN: XXX” is displayed you are in Green dimming
mode. Press the UP and DOWN buttons to adjust intensity.
4. When “BLUE: XXX” is displayed you are in Blue dimming mode.
Press the UP and DOWN buttons to adjust intensity.
5. When “WHIT: XXX” is displayed you are in White dimming mode.
Press the UP and DOWN buttons to adjust intensity.
6. When “AMBE: XXX” (Amber) is displayed you are in Amber dim ming mode. Press the UP and DOWN buttons to adjust intensity.
7. When “UV: XXX” is displayed you are in UV dimming mode. Press
the UP and DOWN buttons to adjust intensity.
8. After you have adjusted the colors to make your desired color
you can then activate strobing by pressing the SET UP button to
enter the strobe mode.
9. “STRO: XX” will be displayed, this is strobe mode. The strobe
can be adjusted between “00” (flash off) to “15” (fastest flash).
Sound Active Mode:
In this mode the Ultra Hex Bar 6 will react to sound, and chase
through the different colors.
1. Plug the fixture in and press the MODE button until “SOUND” is
displayed.
2. Use the UP or DOWN buttons to adjust the sound sensitivity.
“00” is off, “01 is the least sensitive, and “16” is the most sensi-
tive.
3. After you have adjusted the sound sensitivity you can then acti vate strobing by pressing the SET UP button to enter the strobe
mode.
4. “STRO: XX” will be displayed, this is strobe mode. The strobe can
be adjusted between “00” (flash off) to “15” (fastest flash).
Program Mode:
1. Plug the fixture in and press the MODE button until “PROG RUN”
is displayed. Press the SET UP button so that “PROG: XX” is dis-
played.
2. Use the UP or DOWN buttons to scroll through the 20 programs.
Once you have found your desired program press the SET UP
button to adjust the program speed.
3. “SPEED:XX” will be displayed. Use the UP or DOWN button to
adjust the speed between “01” (slowest) and “16” (fastest). Once
you have set your desired running speed, press the SET UP but ton to to enter the fade adjustment mode.
4. “FADE: XX” will be displayed. Use the UP or DOWN button to
adjust the speed between “01” (fastest) and “16” (slowest) or “00”
(Off).
5. After you have adjusted the fade speed you can then activate
strobing by pressing the SET UP button to enter the strobe mode.
6. “STRO: XX” will be displayed, this is strobe mode. The strobe can
be adjusted between “00” (flash off) to “15” (fastest flash).
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 9ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 8
Page 6
Ultra Hex Bar 6 Operating Instructions
Ultra Hex Bar 6 Operating Instructions
Auto Run Mode:
1. Plug the fixture in and press the MODE button until “AUTO RUN”
is displayed.
2. Press the SET UP button until “SPEED: XX” is displayed. When
this is displayed you can adjust the running speed of your Auto
Mode. Use the UP or DOWN button to adjust the speed between
“01” (slowest) and “16” (fastest). Once you have set your desired
running speed, press the SET UP button to adjust the fade speed
of the Auto Mode.
3. “FADE: XX” will be displayed. Use the UP or DOWN button to
adjust the speed between “01” (fastest) and “16” (slowest) or “00”
(Off).
4. After you have adjusted the fade speed you can then activate
strobing by pressing the SET UP button to enter the strobe mode.
5. “STRO: XX” will be displayed, this is strobe mode. The strobe can
be adjusted between “00” (flash off) to “15” (fastest flash).
Static Color Mode:
1. Plug the fixture in and press the MODE button until “CLR MACS”
is displayed. Press the SET UP button so that “COLOR:XX” is dis-
played.
2. There are 63 colors to choose from. Use the UP and DOWN but tons to scroll through the 63 colors. After you have found your
desired color you can activate strobing by pressing the SET UP
button to enter the strobe mode.
3. “STATIC STRO:XX” will be displayed, this is strobe mode. The
strobing can be adjusted between “00” (flash off) to “15” (fastest
flash).
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC control.
When this function is activated you can control the fixture using the
ADJ RFC (Sold Separately). Please see the next page for ADJ RFC
controls and functions.
1. Plug the fixture in and press the MODE button until “OTHER” is
displayed.
2. Press the SET UP button until “RF: XX” is displayed. “XX” repre sents either “ON” or “OFF”.
3. Use the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
DMX State:
This mode can be used as a precaution mode, that in case the DMX
signal is lost, the operating mode chosen in the setup is the running
mode the xture will go into when the DMX signal is lost. You can also
set this as the operating mode you would like the unit to return to when
power is applied.
1. Press the MODE button until “DMX MODE” is displayed.
2. Press the SET UP button so that “NO:XXXX” is displayed. “XXXX”
represents the current DMX state that is displayed.
• “NO: BLACK” (Blackout) - If the DMX signal is lost or interrupted,
the unit will automatically go into stand by mode.
• “NO: HOLD” (Last State) - If the DMX signal is lost or interrupted,
the xture will stay in the last DMX set up. If power is applied and
this mode is set, the unit will automatically go into the last DMX set
up.
• “NO: AUTO” (Auto Run) - If the DMX signal is lost or interrupted,
the unit will automatically go into Auto Run mode.
3. Use the UP and DOWN buttons to nd your desired DMX state
and press SET UP to conrm and exit.
Dimmer Curve:
This is used to set the dimming curve used with DMX mode. See
page 20 for the different dimming curves.
1. Plug the fixture in and press the MODE button until “DMX MODE”
is displayed.
2. Press the SET UP button until “DELAY: X” is displayed. “X” repre sents the displayed dimmer curve (0-4).
• 0 - Standard
• 1 - Stage
• 2 - TV
• 3 - Architectural
• 4 - Theatre
3. Press the UP or DOWN buttons to scroll through and select your
desired dimming curve.
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 11ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 10
Page 7
Ultra Hex Bar 6 Master-Slave Configuration
Ultra Hex Bar 6 ADJ RFC Operation
Master-Slave Configuration:
This function will allows you to link units together to run in a MasterSlave mode. In Master-Slave operation one unit will act as the con-
trolling unit and the others will react to the controlling units built-in
programs. Any unit can act as a Master or as a Slave however, only
one unit can be programmed to act as the “Master.”
Master-Slave Connections and Settings:
1. Daisy chain your units via the XLR connector on the rear of the
unit. Use standard XLR data cables to link your units together.
Remember that the Male XLR connector is the input and the
Female XLR connector is the ouput. The first unit in the chain
(master) will use the female XLR connector only. The last unit in
the chain will use the male XLR connector only.
2. Set the “Master” unit to your desired mode of operation.
3. Connect the rst “Slave” unit to the “Master.”
4. On the “Slave” unit set it to the DMX MODE setting. The “Slave”
unit will now follow the “Master”.
The ADJ RFC remote (sold seperately) has many different functions
and allows you to control your Ultra Hex Bar 6 from long distance.
The ADJ RFC remote can control your system up to 150 ft. To use
the RFC you must first activate the fixtures receiver, to activate the
receiver please see the instructions on page 10.
BLACKOUT - Pressing this button will blackout the fixture. Press this
button for more then 3 seconds to activate default mode. All modes
will return to their default settings.
AUTO RUN - This button will activate the Auto Run mode. You can
control the fade speed by pressing the FLASH button twice and then
adjust the fade speed using the “+” and “-” buttons. Adjust the program speed of the Auto Run by pressing the SPEED button and then
adjust the speed using the “+” and “-” buttons. Press the FLASH button once to activate strobe and adjust the strobe speed using the “+”
and “-” buttons.
PROGRAM SELECTION - This button will activate 1 of 2 modes;
Static Color mode or Program mode.
1. Press this button to activate Static Color mode. Use the “+” and “-”
buttons to scroll through the 63 colors. Once you have found your desired color press the FLASH button to activate strobing. Use the “+”
and “-” buttons adjust the strobe speed.
2. Press this button to activate Program mode. Use the “+” and “-”
buttons to scroll through the 20 different programs. Once you have
found your desired program press the SPEED button and use the “+”
and “-” buttons to adjust the program speed. Adjust the fade speed
by pressing the FLASH button twice and use the “+” and “-” buttons
to adjust the fade speed. Press the FLASH button once to activate
strobe and adjust the strobe speed using the “+” and “-” buttons.
FLASH - This button will activate the flash (strobe) effect. You can
control the flash speed by pressing the “+” and “-” buttons. In Auto
mode and Program mode, press this button twice to enter fade
speed adjustment. Use the “+” and “-” buttons to adjust the fade
speed.
SPEED - Press this button and use the “+” & “-” buttons to adjust the
speed of the Built-In Programs.
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 13ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 12
Page 8
Ultra Hex Bar 6 ADJ RFC Operation
SOUND ACTIVE - This button activates sound active mode. Use the
“+” & “-” buttons to adjust the sound sensitivity level.
R G B W/A - Press either one of these buttons and the press the
“+” or “-” to adjust the brightness. Press the Flash button to activate
strobing and use the “+” or “-” buttons to adjust the strobe speed.
NOTE: Press the W/A button to scroll through White, Amber, and UV.
“+” and “-” - Use these buttons to adjust the flash rate, speed of the
Auto Run, fade speed, sound sensitivity, and output intensity. Use
these buttons to scroll through the static colors.
Ultra Hex Bar 6 6 Channel - DMX Values & Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 AMBER
0 - 255 0% - 100%
6 UV
0 - 255 0% - 100%
Ultra Hex Bar 6 7 Channel - DMX Values & Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 AMBER
0 - 255 0% - 100%
6 UV
0 - 255 0% - 100%
7 MASTER DIMMER
0 - 255 0% - 100%
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 15ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 14
Page 9
Ultra Hex Bar 6 8 Channel - DMX Values & Functions
Channel Value Function
Ultra Hex Bar 6 12 Channel - DMX Values & Functions
Channel Value Function
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 AMBER
0 - 255 0% - 100%
6 UV
0 - 255 0% - 100%
7 STROBING
0 - 31 OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 PULSE STROBING SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING
224 - 255 LED ON
8 MASTER DIMMER
0 - 255 0% - 100%
1 RED
0 - 255 0% - 100%
2 GREEN
0 - 255 0% - 100%
3 BLUE
0 - 255 0% - 100%
4 WHITE
0 - 255 0% - 100%
5 AMBER
0 - 255 0% - 100%
6 UV
0 - 255 0% - 100%
7 COLOR MACROS
0 - 255 (See Color Macro Chart on page 19)
8 STROBING
0 - 31 OFF
32 - 63 LED ON
64 - 95 STROBING SLOW - FAST
96 - 127 LED ON
128 - 159 STROBE PULSE SLOW - FAST
160 - 191 LED ON
192 - 223 RANDOM STROBING
224 - 255 LED ON
9 MASTER DIMMER
0 - 255 0% - 100%
10 PROGRAMS
0 OFF
1 - 24 PROGRAM 1
25 - 35 PROGRAM 2
36 - 46 PROGRAM 3
47 - 57 PROGRAM 4
58 - 68 PROGRAM 5
69 - 79 PROGRAM 6
80 - 90 PROGRAM 7
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 17ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 16
Page 10
Ultra Hex Bar 6 12 Channel - DMX Values & Functions
Channel Value Function
Ultra Hex Bar 6 18 Channel - DMX Values & Functions
Channel Value Function
10 PROGRAMS
91 - 101 PROGRAM 8
102 - 112 PROGRAM 9
113 - 123 PROGRAM 10
124 - 134 PROGRAM 11
135 - 145 PROGRAM 12
146 - 156 PROGRAM 13
157 - 167 PROGRAM 14
168 - 178 PROGRAM 15
179 - 189 PROGRAM 16
190 - 200 PROGRAM 17
201 - 211 PROGRAM 18
212 - 222 PROGRAM 19
223 - 233 PROGRAM 20
234 - 255 SOUND ACTIVE PROGRAMS
11 PROGRAM SPEED/SOUND SENSITIVE
0 - 255 SLOW - FAST
0 - 255 LEAST SENSITIVE - MOST SENSITIVE
12 DIMMER MODE
0 - 20 STANDARD
21 - 40 STAGE
41 - 60 TV
61 - 80 ARCHITECTURAL
81 - 100 THEATRE
101 - 255 DEFAULT DIMMER SETTING
When Channel 7 is being used, Channels 1-6 will not work.
When Channel 10 is between the values of 1-233, Channel 11 will control the
program speed.
When Channel 10 is between the values of 234-255, Channel 11 will control the
sound sensitivity.
1 0 - 255 RED 0% - 100% PIXEL 1 & 2
2 0 - 255 GREEN 0% - 100% PIXEL 1 & 2
3 0 - 255 BLUE 0% - 100% PIXEL 1 & 2
4 0 - 255 WHITE 0% - 100% PIXEL 1 & 2
5 0 - 255 AMBER 0% - 100% PIXEL 1 & 2
6 0 - 255 UV 0% - 100% PIXEL 1 & 2
7 0 - 255 RED 0% - 100% PIXEL 3 & 4
8 0 - 255 GREEN 0% - 100% PIXEL 3 & 4
9 0 - 255 BLUE 0% - 100% PIXEL 3 & 4
10 0 - 255 WHITE 0% - 100% PIXEL 3 & 4
11 0 - 255 AMBER 0% - 100% PIXEL 3 & 4
12 0 - 255 UV 0% - 100% PIXEL 3 & 4
13 0 - 255 RED 0% - 100% PIXEL 5 & 6
14 0 - 255 GREEN 0% - 100% PIXEL 5 & 6
15 0 - 255 BLUE 0% - 100% PIXEL 5 & 6
16 0 - 255 WHITE 0% - 100% PIXEL 5 & 6
17 0 - 255 AMBER 0% - 100% PIXEL 5 & 6
18 0 - 255 UV 0% - 100% PIXEL 5 & 6
Ultra Hex Bar 6 Color Macro Chart
0-3=Off 64-67=B+W 128-131=G+B+W 192-195= R+B+W+A
4-7=Red 68-71=B+A 132-135=G+B+A 196-199=R+B+W+UV
8-11=Green 72-75=B+UV 136-139=G+B+UV 200-203=R+B+A+U V
12-15=Blue 76 -79=W+A 140-143=G+W+A 204-207=R+W+A +UV
16-19=White 80-83=W+UV 144-147=G+W+UV 208-211=G+B+W+A
20-23=Amber 84-87=A+UV 148-151=G+A+UV 212-215=G+B+W+U V
24-27=UV 88-91=R+G+B 152-155=B+W+A 216-219=G+B+A+UV
28-31=R+G 92-95=R+G+ W 156-159=B+W+UV 220-223=G+ W+A+UV
32-35=R+B 96- 99=R+G+A 160-163=B+A+UV 224-227=B+W+A +UV
36-39=R+W 100-103=R+G+U V 164-167=W+A+U V 228-231=R+G+B +W+A
40-43=R+A 104-107=R+B+W 168-171=R+G+B+W 232-235=R+G+B+W +UV
44-47=R+UV 108-111=R+B+A 172-175=R+G+B+A 236-239=R+G+B+A+UV
48-51=G+B 112-115=R+B+U V 176-179= R+G+B+UV 240-243=R+G+W+A +UV
52-55=G+W 116-119=R+W+A 180-183=R+G+W+A 244-247=R+B+W+A=UV
56-59=G+A 120-123=R+W+UV 184-187=R+G+W+U V 248-251=G+B+W +A+UV
60-63=G+UV 124-127=R +A+UV 188-191=R +G+A+UV 252-255=R+G+B+W+A+UV
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 19ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 18
Page 11
Ultra Hex Bar 6 Photometric Chart
Ultra Hex Bar 6 Power Cord Daisy Chain
With this feature you can connect the xtures to one another
using the IEC input and output sockets. The quantity that can be
connected is 12 xtures maximum. After 12 xtures you will need
to use a new power outlet. They must be the same xtures. DO
NOT mix xtures.
Ultra Hex Bar 6 Fuse Replacement
Disconnect the unit from its power source. Remove the power cord
from the unit. Once the cord has been removed, you will find that the
fuse holder is located inside the power socket. Insert a flat-head screw
driver into the power socket and gently pry out the fuse holder. Remove
the bad fuse and replace with a new one. The fuse holder also has a
holder for a spare fuse.
Ultra Hex Bar 6 Trouble Shooting
Listed below are a few common problems the user may encounter,
with solutions.
Ultra Hex Bar 6 Dimmer Curve Chart
Ramp Effect
Standard
Stage
TV
Architectural
Theatre
(Fade Time) (Fade Time)
Unit not responding to DMX:
1. Check that the DMX cables are connected properly and are
wired correctly (pin 3 is “hot”; on some other DMX devices
pin 2 may be ‘hot’). Also, check that all cables are connected
to the right connectors; it does matter which way the inputs
and outputs are connected.
Unit does not respond to sound:
1. Quiet or high pitched sounds will not activate the unit.
2. Make sure that Sound Active mode is activated.
Ultra Hex Bar 6 Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out periodically to optimize light
output.
1. Use normal glass cleaner and a soft cloth to wipe down the
outside casing.
2. Clean the external optics with glass cleaner and a soft cloth
every 20 days.
3. Always be sure to dry all parts completely before plugging
the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (i.e. smoke, fog residue, dust, dew).
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 21ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 20
Page 12
Ultra Hex Bar 6 Warranty
MANUFACTURER’S LIMITED WARRANTY
A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products
to be free of manufacturing defects in material and workmanship for a prescribed period from
the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the
product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the
product–please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the ADJ Products, LLC factory. All shipping charges must be pre-paid. If the requested repairs or
service (including parts replacement) are within the terms of this warranty, ADJ Products, LLC will pay
return shipping charges only to a designated point within the United States. If the entire instrument is
sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If
any accessories are shipped with the product, ADJ Products, LLC shall have no liability whatsoever for
loss of or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is modified in any
manner which ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the
product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior
written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because
not properly maintained as set forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintnance, cleaning or periodic check
up. During the period specified above, ADJ Products, LLC will replace defective parts at its expense
with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by
reason of defects in material or workmanship. The sole responsibility of ADJ Products, LLC under this
warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole
discretion of ADJ Products, LLC. All products covered by this warranty were manufactured after August
15, 2012, and bear indentifying marks to that effect.
E. ADJ Products, LLC reserves the right to make changes in design and/or improvements upon its products
without any obligation to include these changes in any products theretofore manufactured.
No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with
products described above. Except to the extent prohibited by applicable law, all implied warranties made
by ADJ Products, LLC in connection with this product, including warranties of merchantability or fitness,
are limited in duration to the warranty period set forth above. And no warranties, whether expressed or
implied, including warranties of merchantability or fitness, shall apply to this product after said period
has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is
expressly provided above; and under no circumstances shall ADJ Products, LLC be liable for any loss or
damage, direct or consequential, arising out of the use of, or inability to use, this product.
This warranty is the only written warranty applicable to ADJ Products, LLC Products and
supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore
published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
•LightingProducts=1-year(365days)LimitedWarranty(Such as: Special Effect Lighting, Intelligent
Lighting, UV lighting, Strobes, Fog Machines, Bubble Machines, Mirror Balls, Par Cans, Trussing,
Lighting Stands etc. excluding LEDs and lamps)
•LaserProducts=90-DayLimitedWarranty
•L.E.D.Products=2-year(730days)LimitedWarranty(excluding motors, PCB boards, and power
supplies, which have a 1-year (365 day Limited Warranty) and batteries which have a 180 day
limited warranty).
ADJ Products, LLC - www.adj.com - Ultra Hex Bar 6 User Manual Page 22
Ultra Hex Bar 6 Specifications
Model:
Ultra Hex Bar 6
Voltage: 100V ~ 240V/50~60Hz
LEDs: 6 x 10W 6-in- Hex LED’s
Beam Angle: 40 Degrees
Working Position: Any safe working position
Power Draw: 55W
Power Cord Daisy Chain: 12 Fixtures Max.
Fuse: 2 Amp
Weight: 6lbs./ 2.82Kgs.
Dimensions: 23” (L) x 4.5” (W) x 6.5” (H)
585 x 110 x 165mm
Colors: RGBAW + UV Color Mixing
DMX Channels: 5 DMX Modes: 6 Channel Mode,
7 Channel Mode, 8 Channel Mode,
12 Channel Mode, & 18 Channel
Mode
Warranty: 2 Year (730 days)
Auto Sensing Voltage: This xture contains a automatic voltage
switch, which will auto sense the voltage when it is plugged into
the power source.
Please Note: Specications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
ADJ Products, LLC
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.adj.com / E-mail: info@americandj.com
A.D.J. Supply Europe B.V.
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.adj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99
Loading...