A&D HV-60KCP, HV-200KC, HV-200KCP, HW-10KC, HW-10KCP Instruction Manual

...

Page 1

Digital Platform Scale

Global models

HV-15KC HV-15KCP HV-60KC HV-60KCP HV-200KC HV-200KCP HW-10KC HW-10KCP HW-60KC HW-60KCP HW-100KC HW-100KCP HW-200KC HW-200KCP

Region - limited models

HV-300KC HV-300KCP HV-600KC HV-600KCP HW-300KC HW-300KCP HW-600KC HW-600KCP

1WMPD4003471B

Page 2

© 2019 A&D Company Ltd. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, or translated into any language in any form by any means without the written permission of A&D Company Ltd.

The contents of this manual and the specifications of the instrument covered by this manual are subject to change for improvement without notice.

Windows, Word and Excel are registered trademarks of the Microsoft Corporation.

Page 3

HV/HW-C/CP Series Page 1

Contents

1. Compliance.................................................................................................................................. 3

1.1. Compliance with FCC Rules................................................................................................... 3

2. Outline and Features .................................................................................................................. 3

3. Precautions..................................................................................................................................5

3.1. Installing the Scale................................................................................................................... 5

3.2. Operating the Scale ................................................................................................................. 5

3.3. Storing the Scale...................................................................................................................... 6

4. Setting up and Installing the Scale............................................................................................. 7

4.1.1. Model-A Procedure to Assemble the Scale....................................................................... 7

4.1.2. Method-B Procedure to Assemble the Scale ....................................................................8

5. Package Contents ...................................................................................................................... 9

5.1. Accessories and Options List................................................................................................11

5.1.1. Accessories List ..................................................................................................................11

5.1.2. Options List..........................................................................................................................12

5.2. Installing the Batteries for Type C.........................................................................................13

5.3. Removing the Pole ................................................................................................................14

5.3.1. Method-A Procedure to Remove the Pole.......................................................................14

5.3.2. Method-B Procedure to Remove the Pole.......................................................................16

5.4. Grounding the Scale..............................................................................................................17

5.4.1. Method-A Procedure to Ground the Scale ......................................................................17

5.4.2. Method-B Procedure to Ground the Scale ......................................................................17

5.4.3. Method-C Procedure to Ground the Scale...................................................................... 17

6. Description of Each Part...........................................................................................................18

6.1. Display and Symbols.............................................................................................................20

6.2. Keys........................................................................................................................................ 22

7. Basic Operation.........................................................................................................................24

7.1. Turning the Scale On/Off and Weighing ..............................................................................24

7.1.1. When Using the AC Adapter..............................................................................................24

7.1.2. When Using the Batteries for Type C................................................................................25

7.1.3. Power on Zero Function and Power on Tare Function.................................................... 25

7.2. Tare Function to Display Net Value...................................................................................... 26

7.2.1. Inputting Tare Value by Weighing .....................................................................................26

7.2.2. Digital Input of Tare Value (Preset Tare)........................................................................... 26

7.3. Switching the Mode ...............................................................................................................27

8. Counting Mode.......................................................................................................................... 28

8.1. Storing a Unit Mass................................................................................................................28

8.2. Counting the Number of Articles........................................................................................... 29

9. Accumulation Function .............................................................................................................30

10. Comparator................................................................................................................................32

10.1.1. Setting a Mode and Method...............................................................................................33

10.1.2. Comparison and Formula ..................................................................................................34

Page 4

Page 2 HV/HW-C/CP Series

10.1.3. Setting Threshold Values (of Limits and Ranks) ..............................................................36

10.1.4. Buzzer of Comparator Mode..............................................................................................37

11. Auto-Tare...................................................................................................................................38

12. Built-in Printer of Type CP....................................................................................................... 39

12.1.1. Installing the Roll Paper...................................................................................................... 40

13. ID Number and GLP................................................................................................................. 41

13.1. Setting the ID Number........................................................................................................... 41

13.1.1. Display Character Table..................................................................................................... 41

13.2. Setting the Clock ....................................................................................................................42

13.3. GMP Report........................................................................................................................... 43

14. Calibration (Adjusting the Scale)..............................................................................................47

14.1. Gravity Acceleration Table ....................................................................................................48

14.2. Complete Calibration Procedure...........................................................................................49

14.2.1. Gravity Acceleration Correction......................................................................................... 49

14.2.2. Preparation..........................................................................................................................49

14.2.3. Calibration of the Zero Point...............................................................................................50

14.2.4. Span Calibration ................................................................................................................. 50

15. Function Table...........................................................................................................................51

15.1. Parameter Setting Procedure ...............................................................................................51

15.2. Parameter List........................................................................................................................ 52

15.3. Initializing Parameters of the Function Table....................................................................... 58

16. Options.......................................................................................................................................59

16.1. Installing Options.................................................................................................................... 59

16.2. HVW-02CB, USB Interface.................................................................................................. 60

16.2.1. Procedure for Using the USB Interface............................................................................. 60

16.2.2. Example of Using the USB Interface................................................................................. 60

16.3. HVW-03C, RS-232C Interface ...........................................................................................62

16.4. HVW-04C, Comparator Relay Output / Buzzer / Contact Input ........................................63

16.5. Communication Format......................................................................................................... 65

16.5.1. Command Mode................................................................................................................. 67

16.6. Using UFC (Universal Flex Coms) Function........................................................................74

17. Specifications ............................................................................................................................77

18. Maintenance..............................................................................................................................83

18.1. Repair .....................................................................................................................................83

18.2. Check Points Before Calling Maintenance Service.............................................................83

19. Index ..........................................................................................................................................85

Page 5

HV/HW-C/CP Series Page 3

Compliance

1.1.

Compliance with FCC Rules

Please note that this equipment generates, uses and can radiate radio frequency energy.

This equipment has been tested and has been found to comply with the limits of a Class A computing device pursuant to Subpart J of Part 15 of FCC rules. These rules are designed to provide reasonable protection against interference when this equipment is operated in a commercial environment. If this unit is operated in a residential area it might cause some interference and under these circumstances the user would be required to take, at his own expense, whatever measures are necessary to eliminate the interference.

(FCC = Federal Communications Commission in the U.S.A.)

Outline and Features

The HV-C/CP series are platform scales with 1/3000 resolution.

These scales have the triple weighing range function to select the weighing range. The scale automatically switches to small interval when a light sample is weighed or large interval when a heavy sample is weighed, depending on the sample weight (multi-interval).

The HW-300KC, HW-300KCP, HW-600KCP and HW-600KC are platform scales with

1/6000 resolution. Other HW models are platform scales with 1/10000 resolution.

Type CP scales are equipped with a built-in printer.

Type C scales use batteries or an AC adapter as a power source.

The scales use a backlit liquid crystal display to enable viewing in dim light.

Using the optional RS-232C serial interface or USB interface, data can be output to a printer.

Also, the weighing value can be output, the scale can be controlled or the setting value can be set by a command from a personal computer.

The counting mode converts the total mass value (total weight) of articles to a count when each

article has the same mass value.

The scale has an accumulation function with a maximum of 6 digits, which can accumulate up

to 999 times. (The number of times weighed and the total mass value can be stored in the scale.)

The comparator function compares the displayed weighing value against preset limit values and

displays the result. The result can be output by a buzzer if optional HVW-04C is installed.

An optional RS-232C serial interface, USB interface or comparator relay output can be installed

up to three units into the scale.

Page 6

Page 4 HV/HW-C/CP Series

The following parameters are stored in the scale even if the AC adapter or batteries are

removed or the display is turned off (standby mode).

Display mode (weighing unit) Unit mass of counting mode Total count and total mass value of accumulation function Preset limit values of comparator function Calibration data Parameters of the function table

Multi-interval:

The minimum display is automatically switched depending on the sample weight. When exceeding the small, medium or large ranges, the interval of display is automatically switched.

Example of an HV-60KC where weighing capacity is 60kg:

The minimum display is 0.005 kg, 0.01 kg or 0.02 kg.

Principal performance of this function:

When a light sample is weighed, the interval of display is small. When a heavy sample is weighed, the interval of display is large.

Weighing capacity

60 kg

30 kg 15 kg

0.005 kg 0.01 kg 0.02 kg Minimum display ( Interval of display )

Medium range

Large range

Small range

Page 7

HV/HW-C/CP Series Page 5

Precautions

3.1.

Installing the Scale

Consider the following conditions to get the most from your scale.

Install the scale where the temperature and relative humidity are stable, there is no draft and a

stable power source is available.

Install the scale on a solid and level surface.

Do not install the scale in direct sunlight.

Do not install the scale near heaters or air conditioners.

Do not install the scale where there is flammable or corrosive gas present.

Do not install the scale near equipment that produces strong magnetic fields.

Do not install the scale where there may be static electricity. When the relative humidity is lower

than 45%R.H., plastic and isolators are apt to be charged with static electricity.

The display unit is not water resistant. Use the display unit cover to avoid damage.

Do not use an unstable power source.

Remove the protective film from the weighing pan before use.

30 minutes before the scale is used, connect the power (the AC adapter or batteries) and press

the ON/OFF key to turn the display on.

The scale is designed for indoor use. If the scale is used outdoors, it may receive electrical

shock of thunder surge and suffer malfunction and damage.

3.2.

Operating the Scale

Calibrate the scale before using and after moving it to another location.

Do not place anything on the weighing pan that exceeds the weighing capacity.

Do not drop anything on the weighing pan.

Do not use a sharp instrument such as a pencil to press the keys. Press the keys gently using

your finger.

Pressing the ZERO key before each weighing is recommended in order to prevent possible

error.

Periodically confirm that the weighing value is correct.

Replace used batteries with four new ones when the

mark is displayed.

Batteries are type D, Mono, R20P, R20PU or LR20.

Page 8

Page 6 HV/HW-C/CP Series

3.3.

Storing the Scale

Do not disassemble the scale.

Do not use solvents to clean the scale. Wipe it with a dry lint-free cloth or a lint-free cloth

moistened with water and a mild detergent.

The base unit can be cleaned with gentle running tap water. Do not scratch the base unit with a

brush. Allow the unit to dry before using.

Caution

The base units of the following models are not waterproof. HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Protect the display unit from dust and water.

Remove the batteries from the display unit when the scale is not to be used for a long time.

If you leave the batteries installed, they may leak and damage the scale.

Page 9

HV/HW-C/CP Series Page 7

Setting up and Installing the Scale

There are two ways of assembling (setting up) the HV-C/CP and HW-C/CP series. Assemble the scale according to the method-A procedure or method-B procedure.

Models Reference S-model: HV-15KC, HV-15KCP, HW-10KC, HW-10KCP M-model: HV-60KC, HV-60KCP, HW-60KC, HW-60KCP

Method-A procedure

to assemble the scale

L-model: HV-200KC, HV-200KCP, HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

L2-model: HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Method-B procedure

to assemble the scale

4.1.1. Model-A Procedure to Assemble the Scale

HV-15KC, HV-15KCP, HV-60KC, HV-60KCP, HV-200KC, HV-200KCP, HW-10KC, HW-10KCP,

HW-60KC, HW-60KCP, HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

This procedure is used to set up the above models and includes steps that may not be necessary for some models.

Step 1

Take the base unit and pole out from the shipping

package, taking care not to pull on the load cell cable.

Step 2

Place the weighing pan on the base unit. Peel the

protective film from the weighing pan before use.

Step 3

Assemble the pole. Attach the pole to the bracket of the

base unit, taking care not to damage the load cell cable. Insert the remainder of the load cell cable into the pole. Affix the pole to the bracket using two hex screws.

Note With S-models, this procedure is not required because

the pole and bracket are a combined unit.

Step 4

Select a place to install the scale.

Refer to "3.1. Installing the Scale" .

Step 5

Adjust the level using the bubble spirit and four leveling

feet of the base unit. Place the pole on the floor using the pole foot.

Step 6

Arrange the angle of the display unit. Press the caps at

the pole top from both sides and adjust the angle of the display unit.

Step 7

Check the weighing accuracy. If the scale needs

calibration, refer to "14. Calibration".

The display unit can be adjusted in four steps vertically.

Setting the display sideways is also possible. (Make sure that the pole is secured at the lower part of the pole using hex screws. Do not turn the display unit at a joint for the pole.)

Bubble spirit level

Leveling foot Pole foot

Step 5

OK: Level NO: Inclination

Step 6

Weighing Pan Pole

Step 2 Step 1

Base unit Load cell cable

Pole Step 3 Hex screws

Bracket

mm hex wrench

Page 10

Page 8 HV/HW-C/CP Series

4.1.2. Method-B Procedure to Assemble the Scale

HV-300KC, HV-300KCP, HV-600KC, HV-600KCP,

HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

This procedure is used to set up the above models.

Note Display unit, pole and base unit are connected by

cable. Take care not to pull on the load cell cable.

Step 1

Take the display unit, base unit and pole out

from the shipping package taking care not to pull on the load cell cable.

Step 2

Remove the weighing pan.

Step 3

Assemble the pole and display unit.

Affix the pole and display unit using four 4 mm screws. Use the Phillips screwdriver included. Bundle the AC adapter cable and communication cable using two cable clamps that affix to the pole.

Step 4

Arrange the angle of the display unit.

Press the caps at the pole top from both sides and adjust the angle of the display unit.

Step 5

Connecting the load cell cable.

Connect the load cell cable to the display unit. Close the cable cover, hook the cable in hooks and adjust cable length. Close the bracket cover.

Step 6

Assemble the base unit and pole.

Affix the pole and base unit using four hex screws (and flat washers) so as not to damage the load cell cable. Use the hex wrench included. Bundle the remainder of the load cell cable using the included cable ties.

Step 7

Place the weighing pan on the base unit.

Affix the weighing pan using four 5 mm screws. Use the Phillips screwdriver included. Peel the protective film from the weighing pan.

Step 8

Select a place for installing the scale.

Refer to "3.1. Installing the Scale" .

Step 9

Adjust the bubble spirit level.

Adjust the level of the base unit using the bubble spirit level and the leveling feet.

Step 10

Check the weighing accuracy. If the scale

needs calibration, refer to "14. Calibration".

Four hex screws Hex wrench to affix pole Step 6 Four flat washer

Tied cable

Pole

Weighing pan

OK: Level NO: Inclination Bubble spirit level

Four 5 mm screws Leveling foot

Step 9 Step 7

Step 5 Cable cover Connector

Load cell cable

Step 4 Bracket cover Hook

ccessory Step 2 Weighing Pan box Display unit box

Tied cable

Base unit

Cable cover

Load cell cable Pole

Display unit Step

Four 4 mm screws

Phillips screwdriver

Pole

Cable clamp (2 pieces)

Page 11

HV/HW-C/CP Series Page 9

Package Contents

S-models L-models

HV-15KC HV-200KC HV-200KCP HV-15KCP HW-100KC HW-100KCP HW-10KC Display unit HW-200KC HW-200KCP HW-10KCP Display unit

Weighing pan

M-models Display unit Weighing pan

HV-60KC HV-60KCP HW-60KC HW-60KCP

Weighing pan

Base unit

Caution Do not pull the load cell cable.

Accessories

Accessories supplied depend on the scale. Refer to "5.1. Accessories and Options List".

Display unit cover Hex wrench AC adapter AXP-3003217D Please confirm that the AC adapter type is correct

for your local voltage and receptacle type. The AC adapter may not be provided for some areas.

Page 12

Page 10 HV/HW-C/CP Series

L2-models

HV-300KC HV-300KCP Display unit HV-600KC HV-600KCP HW-300KC HW-300KCP HW-600KC HW-600KCP

Caution The load cell cable is not connected when shipping.

Weighing pan

Caution Do not pull the load cell cable.

Base unit

Accessories

Accessories supplied depend on the scale. Refer to "5.1. Accessories and Options List".

Display unit cover AC adapter AXP-3003217D Please confirm that the AC adapter type is correct for

your local voltage and receptacle type. The AC adapter may not be provided for some areas.

Tow Cable clamp

Set of hex screws for pole with hex wrench.

Four 4 mm screws for display unit.

Four 5 mm screws for weighing pan

Cable tie Phillips screwdriver Bracket cover

Page 13

HV/HW-C/CP Series Page 11

Type C and CP Type C

Scale with "C" or "CP" at the end of model name. Scale with "C" at the end of model

name.

Batteries (Not included)

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas.

5.1.

Accessories and Options List

5.1.1. Accessories List

Type Models Accessories (Quantity)

HV-15KC HW-10KC

Display unit cover (AXP-3003217D) Instruction manual

AC adapter (1)

HV-60KC HV-200KC HW-60KC HW-100KC HW-200KC

Display unit cover (AXP-3003217D) Hex wrench (1) Instruction manual AC adapter (1)

Type C

( Able to use

battery )

HV-300KC HV-600KC HW-300KC HW-600KC

Display unit cover (AXP-3003217D) Cable clamp (2) Set of hex screws for pole with hex wrench. Bracket cover (1) 4 mm screws for display unit (4) Cable tie (1) 5 mm screws for weighing pan (4) Phillips screwdriver (1) Instruction manual AC adapter (1)

HV-15KCP HW-10KCP

Display unit cover (AXP-3003217D) Roll paper (1 roll) Instruction manual AC adapter (1)

HV-60KCP HV-200KCP HW-60KCP HW-100KCP HW-200KCP

Display unit cover (AXP-3003217D) Hex wrench (1) Roll paper (1 pc) Instruction manual AC adapter (1)

Type CP

( Built-in

printer )

HV-300KCP HV-600KCP HW-300KCP HW-600KCP

Page 14

Page 12 HV/HW-C/CP Series

5.1.2. Options List

Order code Option name Models

HVW-02

Extension load cell cable for L2-models, 5 m

HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP,

HW-600KC, HW-600KCP HVW-02CB USB interface HVW-03C RS-232C interface

HVW-04C

Comparator relay output / Buzzer / Contact input

All models

HVW-08C

Extension load cell cable for models except L2-models, 5 m

HV-15KC, HV-15KCP,

HV-60KC, HV-60KCP,

HV-200KC, HV-200KCP,

HW-10KC, HW-10KCP,

HW-60KC, HW-60KCP,

HW-100KC, HW-100KCP,

HW-200KC, HW-200KCP HVW-11C Wall mounting kit HVW-12C Printer mounting kit (for AD-8127)

All models

HVW-13 Roller conveyor for L-models

HV-200KC, HV-200KCP,

HW-100KC, HW-100KCP,

HW-200KC, HW-200KCP

HVW-14 Roller conveyor for M-models

HV-60KC, HV-60KCP,

HW-60KC, HW-60KCP

FW-15

Stand for the display unit

(The display is not included) FW-16-4 Wheel FW-18-4 Roller conveyor for L2-models

HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

AX-KO2466-200

RS-232C cable, D-sub 25 pin, 2 m. AX-KO2466-500

RS-232C cable, D-sub 25 pin, 5 m. AX-KO2466-1000

RS-232C cable, D-sub 25 pin, 10 m.

All models

Note

Refer to the relevant option manual for use of the following options.

HVW-02, HVW-08C, HVW-11C, HVW-12C, HVW-13, HVW-14, FW-15, FW-16 and FW-18.

Calibrate the scale with a calibration weight when extension cable HVW-02 or HVW-08C is

used, if necessary.

The requirement for the RS-232C communication includes the limitation of cable length and the

limitation due to tolerance against electrical noise from environment. Therefore, it cannot guarantee all of the RS-232C communication.

Consumables

AX-PP147-S Special roll paper for the built-in printer (set of 5 rolls)

Page 15

HV/HW-C/CP Series Page 13

5.2.

Installing the Batteries for Type C

Step 1

Turn off the display.

Remove the AC adapter.

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas.

Step 2

Open the battery cover and inner cover in that order.

Push the battery cover and slide it. Push the hook of the inner cover to the left and lift it.

Step 3

Insert four new batteries with proper polarity (+, -).

Batteries are type D, Mono, R20P , R20PU or LR20.

Step 4

Close the covers in the reverse of the order of step 2.

Caution

When batteries are consumed mostly, the battery mark is displayed. Replace batteries with four new ones, when is displayed. Do not mix used and new batteries. Do not use batteries of different type and manufacturer.

Doing so may cause damage to the batteries and the scale.

Check the battery direction. If the batteries are installed in the wrong direction, it may cause

battery leakage. If the direction of just one battery is wrong, the scale may work temporarily.

The battery life depends on the ambient temperature. It becomes shorter in low temperatures

such as in winter.

Remove the batteries from the display unit, when the scale is not to be used for a long time.

Leaving them installed may result in leakage and cause damage.

Damage due to battery leakage is not covered under warranty.

Step 2 Hook

Inner cover Battery case Battery cover

AC adapter

Step1

Batteries

Step 3

Battery cover

Step 4

Page 16

Page 14 HV/HW-C/CP Series

5.3.

Removing the Pole

Caution

Remove the AC adapter and batteries before removing the pole. When removing the load cell cable, do not pull on the load cell cable connector forcibly and do

not pull on the wires of the cable. Do not pull the load cell cable. Do not bend the cable forcibly. Take care that the load cell cable does not touch the weighing pan inside the base unit. Avoid dust, static electricity and high humidity (or condensation) because the inside of the

display unit is sensitive to those.

The procedure to remove the pole depends on the model. Refer to the list below and select a proper procedure.

Models Reference S-model: HV-15KC, HV-15KCP, HW-10KC, HW-10KCP M-model: HV-60KC, HV-60KCP, HW-60KC, HW-60KCP L-model: HV-200KC, HV-200KCP,

HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

Method-A procedure

to remove the pole

L2-model: HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Method-B procedure

to remove the pole

5.3.1. Method-A Procedure to Remove the Pole

HV-15KC, HV-15KCP, HV-60KC, HV-60KCP, HV-200KC, HV-200KCP, HW-10KC, HW-10KCP,

HW-60KC, HW-60KCP, HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

Step 1

Turn the scale off.

Remove the AC adapter and batteries.

Step 2

Open the rear cover of the display unit.

Gently disconnect the load cell cable connector vertically. (Do not pull toward you).

Step 3

Using a Phillips screwdriver, remove four 4 mm

screws used to attach the display unit to the pole.

Step 4

Remove the ferrite core and the cable clamp from

the load cell cable.

Step 5

Using a Phillips screwdriver; remove 3 mm screws

and the bottom cover of the bracket of M-models and L-models.

Step 6

Carefully remove the load cell cable from the pole

and the bracket. Particularly with S-models, take care not to pull on the connector forcibly.

Cable cover Cable clamp Connector

Load cell cable Ferrite core

Wind up 2 times

4 mm screw Bracket cover Pole and bracket

Pole

Bottom cover

3 mm screws

Page 17

HV/HW-C/CP Series Page 15

Step 7

Arrange the cable so it does not touch the weighing

pan in the base unit. If the cable is untied, the straight length of S-models is approximately 1.5 m, and the straight length of M-models and L-models is approximately 2.5 m. The length of the optional extension load cell cable (HVW-08C) is approximately 5 m.

Step 8

Remove the pole and bracket from the base unit

using a hex wrench.

Hex wrench 5 mm

HV-15KC, HV-15KCP, HV-60KC, HV-60KCP, HW-10KC, HW-10KCP, HW-60KC, HW-60KCP

Hex wrench 6 mm

HV-200KC, HV-200KCP, HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

Step 9

Wind the cable through the ferrite core two times.

Affix the cable to the rear cover using the cable clamp.

Step 10

Connect the cable to the connector.

Close the rear cover.

Step 11

Check the weighing accuracy.

Extension load cell cable (HVW-08C) Display unit

m extension cable

The shape of base unit differs by model.

Hex wrench Hex screws

Pole and bracket

Page 18

Page 16 HV/HW-C/CP Series

5.3.2. Method-B Procedure to Remove the Pole

HV-300KC, HV-300KCP, HV-600KC, HV-600KCP,

HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Step 1

Turn the scale off.

Remove the AC adapter and batteries. .

Step 2

Open the rear cover of the display unit.

Gently disconnect the load cell cable connector vertically. (Do not pull toward you).

Step 3

Using a Phillips screwdriver, remove four 4 mm

screws used to attach the display unit to the pole.

Step 4

Remove the ferrite core and the cable clamp from

the load cell cable.

Step 5

Carefully remove the load cell cable from the pole.

Take care not to pull on the connector forcibly.

Step 6

Arrange the cable so it does not touch the

weighing pan in the base unit. If the cable is untied, the straight length of L2-models is approximately 4.5 m. The length of the optional extension load cell cable (HVW-02) is approximately 5 m.

Step 7

Remove the pole and four hex screws from the base

unit using a hex wrench.

Step 8

Wind the cable through the ferrite core two times.

Affix the cable to the rear cover using the cable clamp.

Step 9

Connect the cable to the connector.

Close the rear cover.

Step 10

Check the weighing accuracy

Extension load cell cable (HVW-02) Display unit

m extension cable

The shape of base unit differs by model.

Cable cover Cable clamp Connector

Load cell cable Ferrite core

Wind up 2 times

4 mm screw Bracket cover Step 7 Hex wrench

Hex screws Step 5

Base unit

Pole

Page 19

HV/HW-C/CP Series Page 17

Pass the grounding wire through the trench. Grounding wire

Ground

5.4.

Grounding the Scale

When using where there may be static electricity, ground the scale. The grounding method depends on the model. Refer to the list below and ground the scale properly. These procedures are only for the grounding part of the scale.

Models Reference

S-model: HV-15KC, HV-15KCP, HW-10KC, HW-10KCP

Method-A procedure

to ground the scale M-model: HV-60KC, HV-60KCP, HW-60KC, HW-60KCP L-model: HV-200KC, HV-200KCP,

HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

Method-B procedure

to ground the scale

L2-model: HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Method-C procedure

to ground the scale

5.4.1. Method-A Procedure to Ground the Scale

HV-15KC, HV-15KCP, HW-10KC, HW-10KCP

Secure the grounding wire using an M4 screw in the screw hole between the two hexagon bolts on the base unit bottom side. ( Part)

5.4.2. Method-B Procedure to Ground the Scale

HV-60KC, HV-60KCP, HV-200KC, HV-200KCP, HW-60KC, HW-60KCP, HW-100KC, HW-100KCP, HW-200KC, HW-200KCP

Secure the grounding wire using the screw that secures the bottom cover. ( Part)

5.4.3. Method-C Procedure to Ground the Scale

HV-300KC, HV-300KCP, HV-600KC, HV-600KCP, HW-300KC, HW-300KCP, HW-600KC, HW-600KCP

Remove the weighing pan. Secure the grounding wire using the screw that secures the band of the load cell cable bundle. ( Part) Pass the grounding wire through the trench the same as the load cell cable. Arrange the grounding wire so it does not touch the weighing pan.

Grounding wire Bottom of base unit

Leveling foot

Ground

Bottom of base unit Bottom cover

Ground

Grounding wire

Page 20

Page 18 HV/HW-C/CP Series

Description of Each Part

S-models M-models

HV-15KC Serial No. (

on the side

) HV-60KC HV-60KCP Serial No. (

on the side

) HV-15KCP Display unit HW-60KC HW-60KCP Display unit HW-10KC HW-10KCP L-models HV-200KC HV-200KCP Cap HW-100KC HW-100KCP Cap Pole HW-200KC HW-200KCP Pole

Leveling foot Base unit Weighing pan ( SUS430 )

Display unit of type C

Leveling foot Base unit Weighing pan ( SUS430 )

Display unit of type CP

Pole foot Bubble spirit level Leveling foot

CAL switch Type CP

Calibrate the scale to weigh correctly.

Battery case

Caution To use the scale, it is necessary to use a weight with a certified mass value.

Page 21

HV/HW-C/CP Series Page 19

L2-models

HV-300KC HV-300KCP Serial No. (

on the side

) HV-600KC HV-600KCP HW-300KC HW-300KCP Display unit HW-600KC HW-600KCP

Cap Pole

Bubble spirit level Leveling foot Base unit Weighing pan ( SUS430 )

Display unit of type C Display unit of type CP

CAL switch Type CP

Calibrate the scale to weigh correctly.

Battery case

Caution To use the scale, it is necessary to use a weight with a certified mass value.

Page 22

Page 20 HV/HW-C/CP Series

6.1.

Display and Symbols

Display and Symbols Description

Stability mark When the current weighing value is stable, this mark is displayed. It means the scale is in the proper condition for reading weighing value.

Zero point mark The zero point is the reference point for weighing. When the ZERO key is pressed with nothing on the weighing pan, this mark and a zero value are displayed.

Net mark When a tare weight (example: container) is placed on the weighing pan and the TARE key is pressed, this mark and a zero value are displayed. The net value is a value the tare value is subtracted from the gross value.

Preset tare mark This mark blinks while a digitally input tare is displayed.

Hold mark This mark is displayed while the display is held.

Accumulation mark This mark is displayed while the accumulation function is used.

Low battery mark for type C This mark is displayed when the battery is close to being depleted (voltage is low). Replace with four new batteries.

Comparator indicator While the comparator function is being used, the weighing value is compared using the preset threshold values and the indicator displays the result.

Weighing value Unit

Zero point (Example) When the ZERO key is pressed with nothing on the weighing pan, the zero value, zero point mark and stability mark are displayed.

The unit of counting mode

Counting mode (Example) This mode counts the number of articles on the weighing pan using the preset unit mass. The unit is .

20 pieces Zero value

Storing the unit mass for the counting mode (Example) The unit mass is stored using 20 samples. The zero value means that no articles are on the weighing pan.

10 pieces Not zero

Storing the unit mass for the counting mode (Example) The unit mass is stored using 10 samples. Sign "-" means that something is placed on the weighing pan.

Page 23

HV/HW-C/CP Series Page 21

Display and Symbols Description

While setting a preset tare (Example) Input a tare value using the numerical keys. Store the new tare value using the ENTER key.

Item Parameter

Function settings (Example) Select the item using the MODE key and enter the item using the ENTER key. Input a parameter using the numerical keys. Store the parameter using the ENTER key.

Fixed value

Hold display (Example) Activate the hold mode in the item of "15.2. Parameter list", if you will hold the display of the weighing value. When the weighing value is "near zero" (within the "zero band") or changes more than (25 % of the hold display

+ 30 digits), the

hold display is canceled.

Weighing error Check the base unit and the weighing pan.

Overload display Remove anything that is on the weighing pan.

Calibration error The calibration weight is too light. Check the base unit and the weighing pan.

Calibration error

The calibration weight is too heavy. Check the base unit and the weighing pan.

Fixed display

An error where the zero value cannot be displayed because the weighing value is unstable when the scale turns on.

Remove anything that is on the weighing pan. Perform zero point calibration. Avoid a breeze or vibration that will affect measurement. Check around the weighing pan.

Blinking

Accumulated data count

Blinking and lighting up

Total mass value of the accumulated data

Example of model label: Max 3 / 6 / 15 kg d = 0.001 / 0.002 / 0.005 kg

The weighing range and measurable minimum display.

Example: The weighing value is displayed up to 15 kg with interval 0.005 kg.

The weighing value is displayed up to 6 kg with interval 0.002 kg. The weighing value is displayed up to 3 kg with interval 0.001 kg.

"digit" is a unit of display and is equivalent to the minimum measurable weighing value. "Max" means the weighing range. "d =" means "digit" and is equivalent to minimum weighing value in the unit of kg. "near zero" or "zero band" is within ±4 digits (four times the minimum weighing value that can

be weighed) from zero point in the weighing unit "kg".

Page 24

Page 22 HV/HW-C/CP Series

6.2.

Keys

Display and Symbols Description

ON/OFF key to show or hide the display alternately.

When the scale is turned on, the electric power is supplied to the electric

circuit inside the scale.

When the scale is turned off, the scale is in standby status. At this time,

only minimum power consumption of the waiting mode and power consumption of AC adapter connected to the AC socket are consumed.

ZERO key.

When the scale is turned on and zero point is weighed with nothing on

the weighing pan, the scale assumes zero point as the reference value of weighing.

When the ZERO key is pressed within 2 % of the capacity and the

weighing value is stable, the scale displays zero point mark and zero value. At this time, if tare function and accumulation mode have been used, that data are deleted.

TARE key.

When the weighing value is a positive stable value and the TARE key

is pressed, the scale displays a zero value as net value, net mark and

zero point mark. The net value is a value obtained by subtracting the

value of tare weight from gross value. Tare weight (container) is placed on the weighing pan and is not included in the net value. (In tare mode)

Note The weighing range is reduced according to value of the tare

weight.

Adds to the accumulated data.

SET key. In the comparator mode, this key selects + and - for limit values.

MODE key

The key switches the mode (weighing unit) to be displayed between

weighing value and count. The mode (weighing unit) is maintained in non-volatile memory, so the scale displays using the most recently used mode (weighing unit) when turning on the power next time.

The key is used to select the items at each setting.

HOLD key The display of the weighing value is held. Refer to the function settings for details.

PRINT key The key is used to print out the value displayed or outputs it as data. Those operations differ depending on the function settings.

Page 25

HV/HW-C/CP Series Page 23

Display and Symbols Description

Press and hold the SET key and press the TARE key. Use these keys to enter preset tare setting mode.

Press and hold the SET key and press the PRINT key. Use these keys to perform paper feed at the built-in printer. (Type CP)

Press and hold the SET key and press the M+ key. Use these keys to display the accumulated results.

Press and hold the SET key and press the COMP key. Use these keys to set limit values for the comparator.

Press and hold the SET key and press the ENTER key. Use these keys to proceed to unit mass storing when using counting mode.

Press and hold the TARE key and press the ON/OFF key. Use these keys to enter the function table.

Page 26

Page 24 HV/HW-C/CP Series

Basic Operation

7.1.

Turning the Scale On/Off and Weighing

7.1.1. When Using the AC Adapter

Step 1

Ground the scale.

Step 2

Confirm that nothing is placed on the weighing pan.

Step 3

Confirm that local voltage and receptacle type are correct.

Step 4

The scale is turned on or off using the ON/OFF key.

Step 5

Check the accuracy of weighing. Allow a 30-minute warm up period before calibration.

Step 6

With nothing on the weighing pan, press the ZERO key to display the zero value.

Step 7

Gently place an article to be weighed on the weighing pan.

Step 8

Wait for the stability mark to be displayed. Read the weighing value.

Step 9

Gently remove the article from the weighing pan.

Step 10

Turn the scale off using the ON/OFF key.

Memo

When the scale is turned off using the ON/OFF key, the scale is in standby status. At this

time, minimum power consumption of the waiting mode and power consumption of the AC adapter connected to the AC socket are consumed. If you want to shut off the power consumption completely, disconnect the AC adapter.

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas.

Page 27

HV/HW-C/CP Series Page 25

7.1.2. When Using the Batteries for Type C

Step 1

Install four new batteries. Refer to "5.2. Installing the Batteries for Type C".

Step 2

Confirm that nothing is placed on the weighing pan.

Step 3

The scale is turned on or off using the ON/OFF key.

Step 4

Check the accuracy of weighing. Allow a 30-minute warm up period before calibration.

Step 5

With nothing on the weighing pan, press the ZERO key to display zero value.

Step 6

Gently place an article to be weighed on the weighing pan.

Step 7

Wait for the stability mark to be displayed. Read the weighing value.

Step 8

Gently remove the article from the weighing pan.

Step 9

Turn the scale off using the ON/OFF key.

Caution

When is displayed, it means that the batteries will run out soon.

Replace used batteries with four new ones when is displayed.

Battery life depends on the ambient temperature.

Remove the batteries from the display unit when the scale is not to be used for a long time.

Leaving them installed may result in leakage and cause a malfunction and damage to the scale.

7.1.3. Power on Zero Function and Power on Tare Function

Power on Zero Function :

When nothing is placed on the weighing pan and the scale is turned on using the ON/OFF

key, the weighing value is assumed as the reference value of weighing. The zero value as gross value and zero point mark are displayed. The power on zero function can be used when the weighing value is within the threshold value from the zero point at calibration.

Power on Tare Function :

When a tare weight (container) is placed on the weighing pan and the scale is turned on using

the ON/OFF key, the tare function is performed and a zero value is displayed as net value.

Zero point mark and net mark are displayed. The power on tare function can be used when

the current zero point is more than the threshold value from the zero point of calibration.

Threshold value

Active function

Principal standard models Approved models

Power on zero function ±50 % of capacity ±10 % of capacity

Power on tare function +50 % of capacity +10 % of capacity

7.2.

Color

Page 28

Page 26 HV/HW-C/CP Series

Tare Function to Display Net Value

The tare function is used to cancel the mass value of a tare weight and to display the net

value, when a container (tare weight) to hold the article to be weighed is placed on the

weighing pan.

Caution

The weighing range is reduced according to the value of the tare weight.

The current net value is reset to zero value when the ZERO key is pressed or the display is

turned off.

For the HV-C and HV-CP series, the storable preset tare value must be within the minimum

weighing range.

7.2.1. Inputting Tare Value by Weighing

How to weigh a tare weight (container) and display the net value.

Step 1

Place the container on the weighing pan.

Wait for the stability mark to be displayed. Press the TARE key. The display becomes zero and the net mark is displayed.

Step 2

Place an article to be weighed in the container.

Wait for the stability mark to be displayed and read the net display.

Step 3

Remove all of the articles and the container from the weighing pan.

7.2.2. Digital Input of Tare Value (Preset Tare)

How to input value of a tare weight using numerical keys and to display the net value.

Step 1

While pressing and holding the SET key, press the TARE key.

The scale displays a blank display or the stored tare value. A blank display means that the tare value is zero (reset value). The PT mark blinks.

Step 2

Input the preset tare value using the numerical keys.

Step 3

Press the ENTER key to store the new preset tare value.

The scale displays the net value as preset tare value subtracted from gross value.

Step 4

Place an article to be weighed in the container.

Wait for the stability mark to be displayed and read the net display.

Step 5

Remove all of articles and the container from the weighing pan.

Page 29

HV/HW-C/CP Series Page 27

7.3.

Switching the Mode

When accumulation data is stored in the scale, the number of accumulations and an

accumulation value can be displayed.

The weighing unit used when turned on is the last weighing unit used before turning off.

Ib-oz display is available only with HV-15KC, HV-15KCP, HW-10KC and HW-10KCP.

lb-oz weighing -

oz weighing

Ib weighing

Counting mode

kg weighing

Comparator limit setting

Preset tare setting

Unit mass storing mode

Number of accumulation

Accumulation value

Page 30

Page 28 HV/HW-C/CP Series

Counting Mode

The counting mode is the function to convert the total mass value (total weight) of articles to a

count, when each article has the same mass value.

To use this function, store a unit mass in advance.

Even if the AC adapter or the batteries is removed, the unit mass is maintained in non-volatile

memory.

8.1.

Storing a Unit Mass

Step 1

Press the MODE key to display the unit .

Step 2

Press the SET and ENTER key to enter the mode

that stores a unit mass.

Step 3

Select the number of samples using the SET key.

The greater the quantity of samples, the greater the accuracy of the count. 5 pieces, 10 pieces, 20 pieces, 50 pieces, 100 pieces

Step 4

Place the container on the weighing pan.

Press the TARE key.

Step 5

Place the number of samples selected at step 3.

Wait for the stability mark to be displayed. Press the ENTER key to store. The count is displayed.

Caution

When the sample total mass value is too small and it

is not possible to calculate a unit mass, the scale displays and returns to step 3. Increase the number of samples. The total sample mass are required more than 10 times of minimum display in kg.

When the unit mass is too small to store, the scale

displays . In this case, the unit mass will not be stored even if the number of samples is increased.

Pressing the MODE key, after is

displayed will display the next unit.

Step 6

Remove the samples and the container from the weighing pan.

Note The shape of the base unit differs depending on the

model.

Number of samples

Container Weighing pan

Zero value

Count

Page 31

HV/HW-C/CP Series Page 29

8.2.

Counting the Number of Articles

Step 1

Press the MODE key to display the unit .

Step 2

Store the unit mass of the article.

Refer to "8.1. Storing a Unit Mass".

Step 3

Place the container on the weighing pan.

Press the

TARE key.

Step 4

Place articles in the container.

Wait for the stability mark to be displayed and read the count.

Step 5

Remove the articles and the container from the

weighing pan.

Storing a unit mass Container Weighing pan

Zero value

Number of samples

Count

Page 32

Page 30 HV/HW-C/CP Series

Accumulation Function

The accumulation function can display the accumulation count and accumulation mass value of

articles to be weighed. Maximum accumulation count is 999 times.

The accumulation function is displayed with up to 6 digits and cannot display the leading digits of

7 or more.

Example: If a 60 kg sample is weighed 17 times, the total is 1020.000 kg.

(60.000 x 17 = 1020.000) The scale displays

To use this function, set the parameters of the "Accumulation function ( )" in the

function table in advance.

To use the built-in printer of type C, set the parameters of the "Built-in printer output mode

(

)" in the function table in advance.

The total count and total mass value are stored in the scale even if the AC adapter or batteries

are removed or the display is turned off (standby mode).

Display and Key Operations of Accumulation Function

The display of the accumulation count has a blinking

M+ without a weighing unit.

The display of the accumulation mass value has a

weighing unit and a blinking M+.

Step 1

Press the SET and M+ key to display the

accumulation count and accumulation mass value.

Step 2

Press the MODE key to display the

accumulation count and accumulation mass value.

Step 3

Press the MODE key to return to weighing

display.

When the ZERO key is pressed in the accumulation

mode, the current data is reset to zero.

When the PRINT key is pressed in the accumulation

mode for type CP, the data is output to the built-in printer.

Refer to "Time and date adding " of the function

table to print the date and time. Refer to "12. Built-in printer Type CP" for print sample.

Caution

The accumulation function is available only when weighing is performed in the same weighing unit.

Weighing display

Press and hold

Press

Accumulation count

Accumulation value

Weighing display

Page 33

HV/HW-C/CP Series Page 31

Parameters of Function Table and Word Definition

"near zero" is within ±4 digits (four times the minimum weighing value that can be weighed) from

zero point in the weighing unit "kg".

Item and

Parameter

Description

Accumulation function not used.

When the weighing value is a positive stable value and not "near zero",

if the M+ key is pressed, the value is accumulated.

The next accumulation can be performed after the display becomes "near zero" or

a negative value.

When the weighing value is a positive stable value and not "near zero",

if the M+ key is pressed, the positive value is added to the accumulation value.

When the weighing value is a negative stable value and not "near zero",

if the M+ key is pressed, the negative value is subtracted from the accumulation value.

The next accumulation can be performed after the display becomes "near zero". When the weighing value is a positive stable value and not "near zero", the value is

accumulated automatically.

The next accumulation can be performed after the display becomes "near zero" or

a negative value.

Use: To weigh each article and accumulate the count and total mass value.

When the weighing value is a positive stable value and not "near zero", the positive

value is added to the accumulation value automatically.

When the weighing value is a negative stable value and not "near zero", the

negative value is subtracted from the accumulation value automatically.

The next accumulation can be performed after the display becomes "near zero".

Page 34

Page 32 HV/HW-C/CP Series

10.

Comparator

The comparator function can select a mode from "Five-level comparator mode", "Three-level

comparator mode (

Upper and lower limit mode

)" and "Seven-level comparator mode (

Ranking mode

)".

Each comparator mode compares the weighing value against the preset threshold values and

outputs the results using LEDs (yellow, green and red).

When the optional comparator relay output (HVW-04C) is installed into the scale, the

comparison result can sound the buzzer synchronized to LEDs and output as relay signal.

Five-Level Comparator Mode :

This mode compares the weighing value with

four threshold values (limit values) and outputs results in five levels of LOLO, LO, OK, HI and HIHI.

Three-Level Comparator Mode (

Upper and lower limit mode

) :

This mode compares the weighing value with two threshold values

(upper and lower limit) and outputs results in three levels of LO, OK and HI.

Seven-Level Comparator Mode (

Ranking Mode

) :

This mode compares the weighing value with five threshold values and outputs results in seven ranks. Out of range (Negative value),

Rank 1 (LOLO), Rank 2 (LO), Rank 3 (OK), Rank 4 (HI), Rank 5 (HIHI), Out of range (Positive value)

To use the comparator modes, item and of the function table must be specified

and threshold values (limit values) of the comparator must be set in advance.

Select a comparator mode at item of the function table. : Five-level comparator mode. : Three-level comparator mode (upper and lower limit mode).

: Seven-level comparator mode (ranking mode).

Select a comparator condition at item of the function table.

: No comparison (comparator function not used). : All data is compared regardless of stability of value. : Stable data is compared (when stability mark lights). : All data is compared regardless of stability of value except "near zero".

: Stable data is compared except "near zero".

: All positive data is compared except "near zero". : Stable positive data is compared except "near zero".

Note

"near zero" is within ±4 digits (four times the minimum weighing value that can be weighed)

from zero point in the weighing "kg".

Red Yellow Green Yellow Red LOLO LO OK HI HIHI

LOLO LO HI HIHI Limit value Limit value Limit value Limit value

Red Green Red LO OK HI

LO HI Limit value Limit value

Red Yellow Green Yellow Red Rank 1 Rank 2 Rank 3 Rank 4 Rank 5

Rank 1 Rank 2 Rank 3 Rank 3 Rank 4 Rank 5 Threshold Threshold Threshold Threshold Threshold Threshold value value lower value upper value value value

Page 35

HV/HW-C/CP Series Page 33

10.1.1. Setting a Mode and Method

Step 1

Turn off the scale using the ON/OFF key.

While pressing and holding the TARE key,

press the ON/OFF key to enter the setting mode. Then the software version is displayed.

Press the MODE key to enter the function table

and class is displayed.

Step 2

Select class using the MODE key.

Press the ENTER key to store it.

Step 3

Item is displayed.

Input a parameter for the mode using the numerical keys. Press the MODE key to proceed to next step.

Step 4

Item is displayed.

Input a parameter for the comparison method using the numerical keys. Press the ENTER key to store it. The scale returns to class level after the is displayed

Step 5

When the ZERO key is pressed, the scale

returns to the weighing mode.

Step 6

Proceed to "10.1.3. Setting Threshold Values

(of Limits and Ranks)" to use the comparator mode.

Display off

Press and hold

Press

Software version

Class of function table

Class

Item

Parameter

Weighing mode

Page 36

Page 34 HV/HW-C/CP Series

10.1.2. Comparison and Formula

Judgment is performed using the formulas below. The result is displayed to the comparator indicator and output to option interface.

Five-Level Comparator Mode

Result Comparison formula LED

Relay

output

LOLO

Displayed value < LOLO limit value or, Displayed value < Out of range (

Negative value

) LOLO

Red

LOLO

Displayed value < LO limit value

Yellow

LO limit value  Displayed value  HI limit value

Green

HI limit value < Displayed value

Yellow

HIHI

HIHI limit value < Displayed value or, Out of range (

Positive value

) < Displayed value

HIHI

Red

HIHI

Three-Level Comparator Mode (

Upper and lower limit mode

)

Result Comparison formula LED

Relay

output

Displayed value < LO limit value or, Displayed value < Out of range (

Negative value

) LOLO

Red

LOLO

LO limit value  Displayed value  HI limit value

Green

HI limit value < Displayed value or, Out of range (

Positive value

) < Displayed value

HIHI

Red

HIHI

Caution The LO result is output to LOLO LED and LOLO option output.

The HI result is output to HIHI LED and HIHI option output.

Seven-Level Comparator Mode (Ranking Mode)

Result Comparison formula LED

Relay output

None

Displayed value < Limit Lower value of Rank 1 or, Displayed value < Out of range (

Negative value

)

No LED

Rank 1

(LOLO)

Displayed value < Limit Lower value of Rank 2

LOLO

Red

LOLO

Rank 2

(LO)

Displayed value < Limit Lower value of Rank 3

Yellow

Rank 3

(OK)

Limit Lower value of Rank 3  Displayed value  Limit Upper value of Rank 3

Green

Rank 4

(HI)

Limit Upper value of Rank 3 < Displayed value

Yellow

Rank 5

(HIHI)

Limit Upper value of Rank 4 < Displayed value

HIHI

Red

HIHI

None

Limit Upper value of Rank 5 < Displayed value or, Out of range (

Positive value

) < Displayed value

No LED

Page 37

HV/HW-C/CP Series Page 35

Threshold values of limits and ranks are common to both the weighing and counting mode.

These threshold values are maintained even if the power supply is off. Ignore the decimal point when setting threshold values of limits and ranks. Comparison is performed in order from the top row to the bottom of each table. These threshold values are not judged. Even if the threshold values are incorrect, no error will be

output.

Page 38

Page 36 HV/HW-C/CP Series

10.1.3. Setting Threshold Values (of Limits and Ranks)

Step 1

While pressing and holding the SET key, press the COMP key to enter the comparator

value setting mode.

Step 2

Input a parameter for the comparison method using the numerical keys of _0_ to _9_, ENTER

key to store and proceed, _C_ key to cancel and SET key to alternate between +/-. However the SET key is dependent on models.

Step 3

When settings of threshold values (of limits and ranks) are finished, is displayed.

(At this time, power-on-zero is not performed.)

Five-Level Comparator Mode

Three-Level Comparator Mode

(Upper and lower limit mode)

Seven-Level Comparator Mode

(Ranking Mode)

Example: HW -60KC LOLO 8.500 kg LO 10.000 kg HI 10.500 kg HIHI 12.000 kg

Example: HV-200KC LO 148.85 kg HI 152.50 kg

Example: HV-15KC Rank 1 (LOLO) 0.500 kg or more Rank 2 (LO) 1.000 kg or more Rank 3 (OK) 1.500 kg to 2.000 kg Rank 4 (HI) up to 2.500 kg Rank 5 (HIHI) up to 3.000 kg

Weighing mode

Input the LOLO limit value

Input the LO limit value

Input the HI limit value

Input the HIHI limit value

Weighing mode

Input the LO limit value

Input the HI limit value

Weighing mode

The HV-C / CP models changes the position of the

minimum display depending on the weighing range. Regard the hidden minimum digit as "0". The HV-C / CP series is as follows : HV-15KC, HV-60KC, HV-200KC, HV-300KC, HV-600KC, HV-15KCP, HV-60KCP, HV-200KCP, HV-300KCP, HV-600KCP

Weighing mode

Input the threshold value of rank 1

Input the threshold value of rank 2

Input the lower threshold value of rank 3

Input the upper threshold value of rank 3

Input the threshold value of rank 4

Input the threshold value of rank 5

Weighing mode

Page 39

HV/HW-C/CP Series Page 37

10.1.4. Buzzer of Comparator Mode

Installing the optional HVW-04C on the scale allows the buzzer to sound in conjunction with LEDs according to the comparison result. The buzzer can be set by using the _1_, _2_, _3_, _4_ and _5_ numerical keys when of the function table is displayed.

To set the buzzer to sound according to comparison result, select the corresponding numerical key to light up the LED (showing that the buzzer is on) or turn it off (showing that the buzzer is off). Each LED can be toggled between on and off by pressing the corresponding key.

Corresponding numerical key

_1_

_2_

_3_

_4_

_5_

LED for the comparison result LOLO LO OK HI HIHI

Image of display during setup

Example : When the result is LOLO or OK, the buzzer sounds.

Step 1

Press the _1_ key to light up the LED for LOLO. If the result is LOLO, buzzer sounds

Step 2

Press the _3_ key to light up the LED for OK. If the result is OK, buzzer sounds

Step 3

Press the ENTER key to store the settings.

Caution When the three-level comparator mode is used, _1_ LOLO, _3_ OK and _5_ HIHI are used

for buzzer settings. _2_ HI and _4_ LO are not used.

Corresponding numerical key

_1_

_2_

_3_

_4_

_5_

LED for the comparison result LOLO LO OK HI HIHI

Image of display during setup

Page 40

Page 38 HV/HW-C/CP Series

11.

Auto-Tare

The HV/HW-C/CP series has an auto-tare function to be used with the comparator mode enabled. Using this function in check weighing, the scale automatically tares, then displays OK for a certain amount of samples and repeats this process for the next weighing. Start with display zero value after tare operation. Place or take away objects until the comparison result shows OK. When the stable display is maintained for the duration specified in the function setting

, the scale will automatically tare the weighing value, show zero value and be ready

for next weighing.

In some countries or areas, the auto-tare function cannot be used on the Legal for Trade models

and the selection in the function settings , and is not available.

To use the auto-tare function, set the function settings below.

: Compare all weighing data (other settings may be used depending on the

application). : Auto-tare function enabled. to : Select the timing to tare automatically to avoid the wrong tare operation,

Example : Too early to tare, so take longer time to go to the next weighing.

Take-away check weighing (Example with setting)

Take-away check weighing (negative comparison) is the way to compare a negative weighing

value while taking away objects from a container. Set the function together with the auto-tare function enabled . In this operation mode, the scale operates as "take-away the objects"  "OK and stable"  "auto-tare"  "take-away the objects"  .

In this setting, the polarity of LOLO, LO, HI, and HIHI limit values are ignored and the scale

shows the comparator results as below.

Note: To start take-away check weighing, be sure to use the TARE key to tare the weighing

value of the container filled with objects. The ZERO key may zero value the display, but the scale goes below the zero point by taking away objects. Then, the auto-tare function or TARE key does not work.

When the function "Tares the initial weighing value ( of container) " is selected :

To start the auto-tare function, usually the container (filled with objects) will be placed on the weighing pan and its weighing value must be tared using the TARE key. When is selected, the scale will tare the initial weighing value ( of container) automatically. When the entire load on the weighing pan is removed, the scale will return to the zero point and the value of the tare weight will be automatically cleared. If the scale does not return to the zero point, press the ZERO key to clear the tare weight.

If the scale is equipped with the optional USB interface (HVW-02CB) or optional RS-232C

serial interface (HVW-03C), the OK weighing data can be output automatically. Set the function setting

or to or .

Weighing value>

Net 0

Negative valu

LOLO

HIHI

-|LOLO limit value|

-|LO limit value

-|HI limit value|

-|HIHI limit value|

Page 41

HV/HW-C/CP Series Page 39

12.

Built-in Printer of Type CP

Specify the parameter of "Built-in printer output mode ( )" in the function table to

use the printer in advance.

Specify the parameters of "Setting the clock ( )" and "Time and date adding

( )" in the function table to print the date in advance.

Specification

Type Line thermal dot type Width of roll paper 58 mm Accessories Special roll paper (1 roll) Characters 32 characters per line

(when using double height and width size, 16 characters per line)

Consumables

Special roll paper AX-PP147-S (set of 5 rolls)

Operation and Print Samples

While pressing and holding the SET key, press the PRINT key. Paper feed is performed.

The following example is when the print mode in the function settings is selected.

Printing example for "Built-in printer output mode - ".

Weighing value

Count

Printing example for "Prints the date and time ".

Date Time Weighing value

Printing example for "Prints the ID ". ID number = 000123

Date Time ID Weighing value

Printing example where data is accumulated automatically and is printed out at the same time.

This is used when "Accumulation mode " and "Built-in printer output mode " are set.

Accumulation mode Built-in printer output mode Prints the date and time

A sample weight is weighed, accumulated and printed.

Date, time and ID are only printed at the first time.

Page 42

Page 40 HV/HW-C/CP Series

Printing example for accumulation result ( accumulated data and count ).

If the PRINT key is pressed while the accumulation result ( accumulated data and count ) is displayed, this result is printed.

12.1.1. Installing the Roll Paper

Step 1

Pull the printer cover toward you to open it.

Step 2

Install the roll paper so that the end of the paper is at

the top.

Step 3

Close the printer cover.

Step 4

When the roll paper is installed successfully, the

built-in printer automatically feeds out the paper.

Caution Do not pull the roll paper after printing. It may cause printing errors next time.

Page 43

HV/HW-C/CP Series Page 41

13.

ID Number and GLP

The ID number is used to identify the scale when Good Manufacturing Practice (GMP) or Good Laboratory Practice (GLP) is used. The following GMP data is output to the built-in printer (HV-CP/HW-CP series) or a personal computer using the RS-232C interface.

Results of calibration ("Calibration report")

Results of calibration test ("Calibration test report")

"Start block" and "End block" for GLP data

13.1.

Setting the ID Number

Step 1

With the power turned off, while pressing and holding

the TARE key, press the ON/OFF key to turn the power on and enter the function setting mode. appears.

Step 2

Press the MODE key several times to display

Step 3

Press the ENTER key.

Enter the ID number using the following keys.

M+ key The blinking digit is moved to the left. PRINT key The blinking digit is moved to the right. Numerical keys A value can be input at the blinking digit.

Refer to the table below for the "13.1.1. Display Character Table".

Step 4

Press the ENTER key to store the settings.

appears after .

Step 5

Press the ON/OFF key to turn the display off or

press the ZERO key.

13.1.1. Display Character Table

0 1 2 3 4 5 6 7 8 9 - A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

0 1 2 3 4 5 6 7 8 9 a b C d e f g H i j k l m n o p q r s t U v w x y z

: Space, ASCII 20h

Press several times

Use corresponding key

Page 44

Page 42 HV/HW-C/CP Series

13.2.

Setting the Clock

The clock can only be set for built-in printer models (Type CP).

Step 1

Turn off the display.

While pressing and holding the TARE key, press the ON/OFF key to turn the display on and enter function setting mode. appears.

Step 2

Press the MODE key several times to display

Step 3

Press the ENTER key to enter date confirmation mode.

To set the time without changing the date, press the MODE key.

- Date setting mode -

Step 4

Press the ENTER key to enter date setting mode.

Set the date using the following keys.

1M+ key The blinking digit is moved to the left

PRINT key The blinking digit is moved to the right Numerical keys A value can be input at the blinking digit

1ZERO key To cancel settings and proceed to step 5.

Step 5

Press the ENTER key after finishing setting. A setting

value is registered, and the scale proceeds to time confirmation mode after displaying .

To return to date confirmation mode, press the MODE key.

-Time setting mode -

Step 6

Press the ENTER key to enter time setting mode.

Set time using the following keys.

1M+ key The blinking digit is moved to the left

PRINT key The blinking digit is moved to the right Numerical keys A value can be input at the blinking digit

1ZERO key To cancel settings and proceed to step 7.

Step 7

Press the ENTER key after finishing setting to register

the set value. The scale displays after displaying .

Step 8

Press the 1ON/OFF key to turn the display off or

press the 1ZERO key.

Press several times

Date

Use corresponding key

Time

Use corresponding key

Page 45

HV/HW-C/CP Series Page 43

Manufacture

Model

Serial number

ID number

Date

Time

Calibration

executed

Calibration weight

Column for

signature

A & D<CRLF> MODE L HV- 15KC<CRLF> S/N 6A6123456<CRLF> ID ABCDEF<CRLF>

DATE<CRLF>

CRLF>

TIME<CRLF>

CRLF>

CALI BRATED(EXT.)<CRLF>

CAL. WEIGHT<CRLF>

+15. 000 kg<

CRLF>

SI GNATURE<CRLF>

CRLF>

13.3.

GMP Report

If the GMP report is printed to an AD-8121B printer or AD-8127 printer, use "Format of

AD-8121B or AD-8127, or " in the function table.

Use "MODE 3" for the AD-8121B. Use "DUMP print mode" for the AD-8127.

If the GMP report is output to a personal computer, use "the general format, or

" in the function table.

Calibration report

Step 1

Perform calibration according to "14.2. Complete Calibration Procedure"

Step 2

appears when calibration is complete.

To output the results

Step 3

appears and the calibration report is output.

Step 4

appears again.

Remove the weight. Press the ON/OFF key to turn the display off or press the CAL switch.

AD-8127 format General format

: Space, ASCII 20h

CR : Carriage return, ASCII 0Dh LF : Line feed, ASCII 0Ah

Page 46

Page 44 HV/HW-C/CP Series

Calibration test report

The calibration test mode is used to compare a calibration weight with the calibration test data weighed by the scale.

Note

This test does not perform calibration.

Step 1

In the weighing mode, press and hold the CAL switch

until appears, and then release the switch.

The calibration test mode is not available when the

function setting

, or

is selected.

Step 2

Press the ENTER key to display .

Step 3

If necessary, change the value of the calibration weight

as described in "14.2.4. Span Calibration" .

Step 4

With nothing on the weighing pan, press the ENTER key.

The zero point is measured and the measured value with the unit "kg" is displayed for a few seconds. Then, the value of the calibration weight is displayed.

Step 5

Place a weight of the same value as displayed on the weighing pan and press the ENTER key to measure it. The measured value with the unit "kg" is displayed for a few seconds.

Step 6

appears.

Step 7

appears and the calibration test report is output.

Step 8

appears again. Remove the weight. Press the ON/OFF key to turn the display off or press the CAL switch.

Press for

Press seconds or more

Release key

Change mass value if necessary

Weighing unit

Output result

Page 47

HV/HW-C/CP Series Page 45

AD-8127 format General format

: Space, ASCII 20h

CR : Carriage return, ASCII 0Dh LF : Line feed, ASCII 0Ah

Output of "Title block" and "End block"

When weighing values are recorded as the GMP report, "Title block" and "End block" are added at the beginning and at the end of a group of weighing data.

Title block

Step 1

In the weighing mode, press and hold the

PRINT key until appears, and release then the key. The scale outputs the "Title block." The scale automatically returns to the weighing mode.

Step 2

Press the PRINT key or select the auto-print mode

to output the weighing values.

Press and hold

To output the "Title block"

To output the weighing values

Manufacture

Model

Serial number

ID number

Date Time

Calibration test

Calibration weight

Zero value

Actual weight

value

A & D<CRLF> MODE L HV- 15 KC<CRLF> S/N 6A6123456<CRLF> ID ABCDEF<CRLF>

DATE<CRLF>

CRLF>

TIME<CRL

CRLF> CAL . TEST(E XT. )<CRLF> ACTUAL<CRLF>

0.000

kg<

CRLF>

+15. 005 kg<

CRLF>

TARGET<CRLF>

+15. 005 kg<

CRLF>

SIGNATURE<CRLF>

CRLF>

Column for

signature

Page 48

Page 46 HV/HW-C/CP Series

End block

Step 3

Press and hold the PRINT key until

appears, and release then the key. The scale outputs the "End block."

Step 4

The scale automatically returns to the weighing mode.

AD-8127 format General format

: Space, ASCII 20h

CR : Carriage return, ASCII 0Dh LF : Line feed, ASCII 0Ah

Press and hold

To output the "End block"

Manufacture

Model

ID number

Date

Starting time

Column for

signature

Weighing value

Ending time

End block

Serial number

A & D<CRLF> MODE L HV-15KC<CRLF> S/N 6A6123456<CRLF> ID ABCDEF<CRLF>

DATE<CRLF>

CRLF>

TIME<CRLF>

CRLF>

START<CRLF>

TIME<CRLF>

CRLF>

S T, +0001. 234

kg<CRLF>

S T, +0002. 345

kg<CRLF>

S T, +0003. 456

kg<CRLF>

S T, +0004. 568

kg<CRLF>

CRLF>

END

CRLF>

TIME<CRLF> SIGNATURE<CRLF>

CRLF>

Title block

Page 49

HV/HW-C/CP Series Page 47

14.

Calibration

(Adjusting the Scale)

The scale is an instrument that weighs the "weight" and displays its "mass".

Calibration is the adjustment function so that the scale can weigh correctly.

Three steps of calibration are available

Gravity Acceleration Correction

Function to correct the scale’s local gravity acceleration, so that the scale functions correctly when the calibrated scale has been moved to a distant place.

Comment Refer to the "14.1. Gravity Acceleration Table" on the next page.

Calibration of the Zero Point

Function to adjust the zero point, so that the zero point mark is displayed when there is nothing on the weighing pan.

Comment The zero point is the reference point for weighing and influences the performance

of scale.

Span Calibration

Function to adjust the span with a calibrated mass, so that the scale can accurately weigh anything within the weighing capacity.

Comment Span means the range of weighing capacity. Use a calibration mass heavier than

two thirds of the weighing capacity.

Caution

Check the accuracy of weighing periodically. Calibrate the scale, if it has been moved to

another location or the environment has changed.

Gravity acceleration correction is not required, when the scale is calibrated with the

calibration mass at the place where the scale is used.

Page 50

Page 48 HV/HW-C/CP Series

14.1.

Gravity Acceleration Table

Amsterdam 9.813 m/s2 Manila 9.784 m/s2 Athens 9.800 m/s2 Melbourne 9.800 m/s2 Auckland, NZ 9.799 m/s2 Mexico 9.779 m/s2 Bangkok 9.783 m/s2 Milan 9.806 m/s2 Birmingham 9.813 m/s2 New York 9.802 m/s2 Brussels 9.811 m/s2 Oslo 9.819 m/s2 Buenos Aires 9.797 m/s2 Ottawa 9.806 m/s2 Calcutta 9.788 m/s2 Paris 9.809 m/s2 Chicago 9.803 m/s2 Rio de Janeiro 9.788 m/s2 Copenhagen 9.815 m/s2 Rome 9.803 m/s2 Cyprus 9.797 m/s2 San Francisco 9.800 m/s2 Djakarta 9.781 m/s2 Singapore 9.781 m/s2 Frankfurt 9.810 m/s2 Stockholm 9.818 m/s2 Glasgow 9.816 m/s2 Sydney 9.797 m/s2 Havana 9.788 m/s2 Tainan 9.788 m/s2 Helsinki 9.819 m/s2 Taipei 9.790 m/s2 Kuwait 9.793 m/s2 Tokyo 9.798 m/s2 Lisbon 9.801 m/s2 Vancouver, BC 9.809 m/s2 London (Greenwich) 9.812 m/s2 Washington, DC 9.801 m/s2 Los Angeles 9.796 m/s2 Wellington, NZ 9.803 m/s2 Madrid 9.800 m/s2 Zurich 9.807 m/s2

Page 51

HV/HW-C/CP Series Page 49

14.2.

Complete Calibration Procedure

14.2.1. Gravity Acceleration Correction

Step 1

Turn on the display.

Open the rear cover of the display unit. Locate the CAL

switch inside. Press the CAL switch to enter calibration mode. Then is displayed.

Step 2

Press the MODE key to enter gravity acceleration

correction mode. Press the ENTER key to make the

numerical value blink and proceed to input mode.

Step 3

Set your local gravity acceleration using the numerical keys.

Step 4

Press the ENTER key to store the new value.

The display returns to gravity acceleration display after

displaying .

Step 5

Press the CAL switch again to finish gravity acceleration

correction.

14.2.2. Preparation

Step 1

Confirm the environmental conditions as follows: Maintain a constant temperature and stable power. Install the scale on a solid floor where there is no draft, vibration, strong magnetic fields or

direct sunlight.

Refer to "3.1. Installing the Scale".

Step 2

Keep the display turned on for at least 30 minutes to warm up the scale.

CAL switch

Use numerical keys

CAL switch

The display is automatically turned off.

Page 52

Page 50 HV/HW-C/CP Series

14.2.3. Calibration of the Zero Point

Step 3

After 30-minute warm up,

press the CAL switch to display .

Press the ENTER key to display .

Step 4

Confirm that nothing is placed on the weighing pan.

Wait for the stability mark to be displayed. Press the ENTER key to store the current condition as the zero point.

Note The shape of base unit differs

depending on model.

Step 5

Calibration of the zero point is finished.

To exit the calibration mode, proceed to step 14.

14.2.4. Span Calibration

Step 6

Set the value of the calibration mass using the numerical keys.

(The initial value depends on the scale model.)

Step 7

Place the calibration weight on the weighing pan.

Wait for the stability mark to be displayed. Press the ENTER key to calculate the span and store it.

Step 8

The scale displays after displaying

to finish setting.

Remove the mass from the weighing pan.

Step 9

Press the CAL switch to finish calibration.

The display is automatically turned off.

Weighing mode

CAL switch

Nothing is placed on the pan

Stability mark

Use numerical keys

Mass of calibration weight

Calibration weight

Stability mark

CAL switch

The display is automatically turned off.

Page 53

HV/HW-C/CP Series Page 51

15.

Function Table

The function table is used to store and refer items that determine the

performance of the scale. Each item has a parameter.

The parameters are stored in the scale even if the AC adapter or

batteries are removed or the display is turned off (standby mode).

15.1.

Parameter Setting Procedure

Step 1

Turn off the display.

While pressing and holding the TARE key, press the ON/OFF key to display software version . Press the MODE key to enter function setting mode. First class is displayed.

Step 2

Press the MODE key to select the desired class, and then

press the ENTER key.

Step 3

The first item of class is displayed.

Press the MODE key to select the desired item, and then input a value using numerical keys.

Step 4

Press the ENTER key to store.

The display returns to class after displaying .

Step 5

Press the ZERO key to return to the weighing mode.

Item Parameter

Display off

Press and hold

Press

Class

Desired class

Desired item

Numerical keys

Parameter

Weighing mode

Page 54

Page 52 HV/HW-C/CP Series

15.2.

Parameter List

For the HV-C/CP series NTEP/Measurement Canada version, the shaded items in the below table cannot be changed by the user, so these items are not displayed.

Class Items

Parameter

Details and usage

All the keys function.

The

ON/OFF

ZERO

TARE

HOLD

, M+ and

keys function.

Key lock

The

ON/OFF

ZERO

and

TARE

keys function.

OFF After 5 minutes After 10 minutes After 15 minutes After 30 minutes

Automatic power off

After 60 minutes

When a stable weighing value is displayed and no operation is made, the scale is automatically turned off after time of the parameter has past.

OFF

Automatic power on

ON The scale automatically turns the power on by connecting

to the power using the AC adapter.

OFF

Zero tracking

±0.5 digit ±1 digit

Stability band width

±2 digits

0.5 seconds

1.0 second

Stability band time

1.5 seconds

Condition for lighting stability mark : Factory settings for stability mark is "within ±0.5 digits" and "within 1.0 second".

Fast response / sensitive to vibration Weighing at good environment

Weighing stabilization level

Slow response / stable weighing For stable weighing Always turned off Always lit

Turns off 5 seconds after stabilizing Turns off 10 seconds after stabilizing Turns off 15 seconds after stabilizing

Back light control

Turns off 30 seconds after stabilizing Dark

Back light brightness

Bright

Dot( . )

Decimal point

Comma( , )

OFF

Automatic tare

: Factory settings

"near zero" is within ±4 digits (four times the minimum weighing value that can be weighed)

from zero point in the weighing unit "kg".

"digit" is equivalent to minimum weighing value in the unit "kg".

Page 55

HV/HW-C/CP Series Page 53

Class Items

Parameter

Details and usage

0 second

0.5 seconds

1.0 second

1.5 seconds

2.0 seconds

2.5 seconds

3.0 seconds

4.0 seconds

5.0 seconds

Interval until making automatic tare

10 seconds

OFF

Tare on initial load

OFF

Accumulates by

M+

key when the value is +, excluding "near zero"

Accumulates by

M+

key when the value is + or -, excluding "near zero"

Accumulates automatically when the value is +, excluding "near zero"

Accumulation mode

Accumulates automatically when the value is + or -, excluding "

near zero

OFF

Holds or releases by the

HOLD

key during stabilization

Hold condition

Automatically holds when detecting stabilization

Does not sound (All LEDs are turned off.)

Buzzer

Method for lighting LED

When lighting up the LED registered to be lit, the buzzer sounds.

Set it using the numerical keys. On/off can be switched alternately. Refer to "10.1.4. Buzzer of Comparator Mode".

Setting key 1 2 3 4 5

Result LED LOLO LO OK HI HIHI

None

ON/OFF

ZERO TARE MODE PRINT M+

External contact input 1

HOLD

None

ZERO TARE MODE PRINT M+

External contact input 2

HOLD

: Factory settings

"near zero" is within ±4 digits (four times the minimum weighing value that can be weighed)

from zero point in the weighing unit "kg".

"digit" is equivalent to minimum weighing value in the unit "kg".

Page 56

Page 54 HV/HW-C/CP Series

Class Items

Parameter

Details and usage

Five-level comparator mode

Three-level comparator mode (

upper and lower limit mode

)

Comparator mode

Seven-level comparator mode (

ranking mode

)

No comparison

All data is compared. Stable data is compared. All data is compared except "near zero". Stable data is compared except "near zero". All positive data is compared except "near zero".

Comparator judgment condition

Stable positive data is compared except "near zero". Dark

Comparator brightness

Bright

Off

Comparator reversal

All LEDs are lit. (

Comparator relays are "Contact".

)

Status of LED when turning on display

All LEDs are off. (

Comparator relays are "No contact".

) 2400 bps 4800 bps

Baud rate 1

(OP-ch1)

9600 bps 7 bit / even 7 bit / odd

Bit length, parity 1

(OP-ch1)

8 bit / non Format 1 Format 1, existing returned value

Communication format 1

(OP-ch1)

UFC 2400 4800

Baud rate 2

(OP-ch2)

9600 7 bit / even 7 bit / odd

Bit length, parity 2

(OP-ch2)

8 bit / non Format 1 Format 1, existing returned value

Communication format 2

(OP-ch2)

UFC

Format 1

Built-in printer communication format

UFC

Not output

Tare data output during tare

Tare data is output

Refer to the item "Example of tare function" in "Data format" of "16.5. Communication Format".

: Factory settings

"near zero" is within ±4 digits (four times the minimum weighing value that can be weighed)

from zero point in the weighing unit "kg". "digit" is equivalent to minimum weighing value in the unit "kg". This item is only displayed on models compatible with this function, is not displayed on other models.

Page 57

HV/HW-C/CP Series Page 55

Class Items

Parameter

Details and usage

Stream mode (commands) Output by command from OP-ch1 or OP-ch2. Output by command from OP-ch1. Output by command from OP-ch2.

Commands to be

output are as follows : Q, A, N

■ Command is output by the PRINT key. Output data at auto-print setting, +5 digits or more and stable

(commands)

Output data at auto-print setting, +5 digits or more, or -5 digits or less

and stable (commands)

Output data at auto-print setting, +5 digits or more and stable when

the comparator is OK (commands)

Output data at auto-print setting, +5 digits or more, or -5 digits or less

and stable when the comparator is OK (commands)

Output mode 1 (OP-ch1)

Print an accumulation value when the accumulation operation is

made (commands)

■

Do not output the date and time Output time (ESC T) 2 Output date (ESC D) 2 Output date and time (ESC D, ESC T) 2

Parameter available when connecting AD-8121B or AD-8127.

Output time (RTC) 1 Output date (RTC) 1

Time and date adding (OP-ch1)

Output date and time (RTC) 1

Parameter available when built-in printer is used.

■

Do not output the ID number.

ID number adding (OP-ch1)

Output the ID number.

■

Do not output Output (ESC D, ESC T output) 2 Format of AD-8121B or AD-8127 Output (DATE, TIME output) General format

GMP output (OP-ch1)

Output (RTC output) 1

: Factory settings 1 RTC : Built-in clock. Parameter available for type CP. 2 ESC D, SEC T :

The time and date uses the calendar function of the AD-8121B and AD-8127. Use the "dump print mode" of the AD-8121B and AD-8127.

"digit" is equivalent to minimum weighing value in the unit "kg".

Page 58

Page 56 HV/HW-C/CP Series

Class Items

Parameter

Details and usage

Stream mode (commands) Output by command from OP-ch1 or OP-ch2. Output by command from OP-ch1. Output by command from OP-ch2.

Commands to be

output are as follows : Q, A, N

■ Command is output by the PRINT key. Output data at auto-print setting, +5 digits or more and stabilization

(commands)

Output data at auto-print setting, +5 digits or more, or -5 digits or less

and stable (commands)

Output data at auto-print setting, +5 digits or more and stable when

the comparator is OK (commands)

Output data at auto-print setting, +5 digits or more, or -5 digits or less

and stable when the comparator is OK (commands)

Output mode 2 (OP-ch2)

Print an accumulation value when the accumulation operation is

made (commands)

■

Do not output the date and time Output time (ESC T) 2 Output date (ESC D) 2 Output date and time (ESC D,ESC T) 2

Parameter available when connecting AD-8121B or AD-8127.

Output time (RTC) 1 Output date (RTC) 1

Time and date adding (OP-ch2)

Output date and time (RTC) 1

Parameter available when built-in printer is used.

■

Do not output the ID number.

ID number adding (OP-ch2)

Outputs the ID number.

■

Do not output Output (ESC D, ESC T output) 2 Format of AD-8121B or AD-8127 Output (DATE,TIME output) General format

GMP output (OP-ch2)

Output (RTC output) 1

: Factory settings 1 RTC : Built-in clock. Parameter available for type CP. 2 ESC D, SEC T :

The time and date uses the calendar function of the AD-8121B and AD-8127. Use the "dump print mode" of the AD-8121B and AD-8127.

"digit" is equivalent to minimum weighing value in the unit "kg".

Page 59

HV/HW-C/CP Series Page 57

Class Items

Parameter

Details and usage

Do not print Output by command from OP-ch1 or OP-ch2. Output by command from OP-ch1. Output by command from OP-ch2.

Commands to be

output are as follows : Q, A, N

■ Print data by the PRINT key. Output data at auto-print setting, +5 digits or more and stable.

Print data at auto-print setting, +5 digits or more, or -5 digits or less

and stable.

Print data at auto-print setting, +5 digits or more and stable when the

comparator is OK.

Print data at auto-print setting, +5 digits or more, or -5 digits or less

and stable when the comparator is OK.

Built-in printer output mode

Print an accumulation value when the accumulation function is used.

■

Do not output the date and time Output time (RTC) Output date (RTC)

Time and date adding

Output date and time (RTC)

Parameter available for built-in printer of type CP.

■

Do not output the ID number.

ID number adding

Output the ID number.

■

Do not print

GMP output

Print (RTC output)

■

Standard

Double height and width size

■

Thermal paper

Built-in printer label mode

( Not used )

0 line 1 line

■

2 lines 3 lines 4 lines 5 lines 6 lines 7 lines 8 lines

Line feed of printer

9 lines

: Factory settings

RTC : Built-in clock. Parameter available for type CP.

"digit" is equivalent to minimum weighing value in the unit "kg".

Page 60

Page 58 HV/HW-C/CP Series

15.3.

Initializing Parameters of the Function Table

The following procedure can reset to the factory settings parameters stored in the function table.

Parameters of the comparator are reset as well.

Step 1

Turn off the display using the ON/OFF key.

Step 2

While pressing and holding the TARE key,

press the ON/OFF key to display .

Step 3

Press the SET key to display .

Step 4

When is displayed,

press the ENTER key to initialize parameters to the factory settings. The scale displays and enters weighing mode.

Page 61

HV/HW-C/CP Series Page 59

16.

Options

The scale is equipped with OP-ch1 and OP-ch2 for communication options, and OP-ch3 only for comparator relay output. Those options can be combined freely. Combinations such as HVW-02BC x 2, HVW-02CB + HVW-03C or HVW-03C x 2 are possible. Only an HVW-04C can be installed to the slot for OP-ch3.

Installation example

OP-ch1: HVW-03C OP-ch3 OP-ch2: HVW-02CB HVW-04C OP-ch3: HVW-04C

OP-ch2 OP-ch1 HVW-02CB HVW-03C

16.1.

Installing Options

Step 1

Remove the two M3 screws at both side on the panel, and then remove the panel from the

display unit.

Step 2

Connect the cable located inside the display unit to the connector on the option panel.

Step 3

Firmly secure the option to the display unit using the two M3 screws.

Panel

Step 1 Step 2

Step 2 Step 1 Step 1 Step 3

Step 2 Step 3 Step 3 Panel Panel

Page 62

Page 60 HV/HW-C/CP Series

16.2.

HVW-02CB

, USB Interface

The HVW-02CB enables duplex communication using a USB interface.

The connector is type B. To connect the HVW-02CB to a computer, a commercially "type A male - type B female" cable can be used. To communicate between the scale and a computer using the USB interface, it is necessary to install the specified driver software to a computer. Download the driver software from the A&D website. The HVW-02CB can only be connected with a computer. Do not use a USB terminal as power supply terminal. Do not connect a device other than a computer to the USB terminal. Dosing so may cause failure and malfunctions.

16.2.1. Procedure for Using the USB Interface

Prepare the computer as shown below.

Step 1

Download the USB driver software from the A&D website.

Step 2

Install the USB driver software to the computer that is used as a COM port.

Step 3

Read the COM port number on the computer.

Step 4

Input the number to the data communication software.

Step 5

Connect the scale to the computer using the USB cable.

Step 6

When the PRINT key is pressed, a weighing value can be received by the data

communication software.

Example of data communication software : RsCom of A&D WinCT.

16.2.2. Example of Using the USB Interface

Reading COM port number ( Computer is used as a COM port.)

Step 1

Download the USB driver software from the A&D website.

Open the A&D website at the URL

http://www.aandd.jp/

and

open the "Support" and "Software" pages in that order. Download the driver software from "download" of "Driver software for HVW-02CB (USB interface option for the HV/W-C & HV/W-CP series)".

Note : The location and version of the software may be changed without notice.

Step 2

Expand the file "

hvw-02cbja_driver.zip

" by double-clicking.

The folder "

hvw-02cbja_driver

" is created.

Step 3

Install the file "

CDM21224_setup.exe

" in the folder by double-clicking.

Step 4

Finish the installation by following the displayed instruction.

Page 63

HV/HW-C/CP Series Page 61

Reading the COM port Number ( Check after software is installed to computer.)

Step 1

Press the START button and open the control panel.

Step 2

Open "Hardware & Sound" and "Device Manager" in that order.

Step 3

Expand the "Ports (COM & LPT)" by

double-clicking to display the COM port number. Port number is "9" in the example.

Note : The COM port number may differ depending on

the hardware of the computer. Confirm the COM port number in device manager.

Communication Software

Example : If the communication software WinCT is used,

data can be stored in memory.

Step 1

Start RsCOM of WinCT for example.

Step 2

Prepare parameters of "Port : COM".

Port number is "9" in the example.

Note : The communication software WinCT can

download from the A&D website of URL

http://www.aandd.jp/

Starting Data Communication

Step 1

Connect the scale to the computer using the USB cable. Use a commercially available "type A male - type B female" cable.

Step 2

Press the Start button of RsCOM of WinCT. Then, communication is available.

Step 3

When the PRINT key of the scale is pressed and weighing value is output, RsCOM can

receive it.

The weighing value to be output to the interface depends on the parameters of the function

table.

Page 64

Page 62 HV/HW-C/CP Series

Inch screw

#4-40UNC

TXD 2 RXD 3 RTS 7 CTS 8 DSR 6 GND 5

RXD TXD RTS CTS DSR GND

16.3.

HVW-03C

, RS-232C Interface

The HVW-03C enables duplex communication using the RS-232C interface.

The DCE (Data Communication Equipment) connector is type DSUB-9P. To connect the HVW-03C to an external device, it is necessary to use a commercially available communication cable. AX-KO2466-200 (2 m) / AX-KO2466-500 (5 m) / AX-KO2466-1000 (10 m)

When confirming the communication format, refer to "16.5. Communication format".

Pin assignment

Pin No. Signal name of DCE side Direction Description

1 No connection 2 TXD Transmit data 3 RXD Receive data 4 No connection 5 GND Signal ground 6 DSR Data set ready 7 RTS Request to send 8 CTS Clear to send 9 Used internally

Inside of the scale Terminal example of DCE side the external device DTE side

Transmission EIA RS-232C Transmission form Asynchronous, bi-directional Data format Baud rate : 2400, 4800, 9600 bps Data length : 7 bits or 8 bits Parity : 1 bit EVEN, ODD Data length is 7 bits NONE (Non-parity) Data length is 8 bits Start bit : 1 bit Stop bit : 1 bit Code : ASCII

Bit format for data 7 bits

LSB

1 2

Start bit Data bits Parity Stop bit

Bit format for data 8 bits

LSB

1 2

MSB

Start bit Data bits Stop bit

1 ( -15 V to -5 V )

0 ( 5 V to 15 V )

1 ( -15 V to -5 V )

0 ( 5 V to 15 V )

Page 65

HV/HW-C/CP Series Page 63

HIHI

KLO

LOL

16.4.

HVW-04C, Comparator Relay Output / Buzzer / Contact Input

Output terminal of comparator & relay

Contact input terminal The buzzer is mounted on the board.

The specifications of the solid state relay are as follows :

Maximum voltage : 50 V DC Socket on the board Maximum current : 100 mA DC Maker : PHOENIX Maximum ON resistance : 8 Ω Model : MSTB 2,5 / 6-GF-5,08

Solid state relay

1 Relay output HIHI 2 Relay output HI 3 Relay output OK 4 Relay output LO 5 Relay output LOLO 6 Common COM

Attached terminal (Accessory of HVW-04C) Manufacturer : PHOENIX 7 mm Model name : MSTB 2,5 / 6-STF-5,08 Wire

Caution When the three-level comparator mode is used, the comparator outputs are the HIHI 1pin, OK 3

pin and LOLO 5 pin. HI 2 pin and LO 4 pin are not used.

1 Relay output HIHI 2 Relay output HI 3 Relay output OK 4 Relay output LO 5 Relay output LOLO 6 Common COM

Buzzer

The buzzer is mounted on the electrical circuit board of the HVW-04C.

When the HVW-04C is installed on the scale, the sound pressure level is approximately 58 dB at a distance of 1 m from the display unit. The buzzer can sound with LEDs (at upper side of the display) synchronized to a comparator result. The use of the buzzer can specify at

of the function table.

Refer to "10.1.4. Buzzer of Comparator Mode".

Page 66

Page 64 HV/HW-C/CP Series

External Contact Input Plug and Wiring Example

An external contact input plug is included.

Solder the plug and electrical wires according to the circuit diagram below.

: The function of the switch can be assigned at the external contact

input in the function table.

: The function of the switch can be assigned at the external contact

input in the function table.

When the wire (or wire) is shorted to GND wire for 100 ms or more,

the specified function of the terminal (or terminal) is performed.

terminal wire switch

GND terminal

External contact input plug

3.5 mm stereo mini-plug or equivalent.

Page 67

HV/HW-C/CP Series Page 65

16.5.

Communication Format

Data format

S T , + 0 0 0 0 0 . 0 0 k g

CR LF

Header Data Unit Terminator

There are 4 headers for the weighing data.

ST : Stable weighing data QT : Stable counting data US : Unstable weighing data OL : Out of weighing range

The data consists of 9 characters including the polarity and decimal point.

There are 4 units. The character means "Space (20h)".

kg : Weighing mode "kg" lb : Weighing mode "lb" oz : Weighing mode "oz" PC : Counting mode "pcs"

As a terminator, CR LF is always output. CR : 0Dh, LF : 0Ah

Data example

Weighing data "kg" (+) S T , + 0 0 1 2 . 3 4 5 k g

CR LF

Counting data "pcs" (+) Q T , + 0 0 0 1 2 3 4 5 P C

CR LF

Out of weighing range "kg" (+) O L , + 9 9 9 9 . 9 9 9 k g

CR LF

HV-C / CP model S T , + 0 0 1 2 . 3 4 k g

CR LF

When the position of the minimum display changes depending on the weighing range, the hidden digit is replaced to .

Example of tare function

When "tare data is output (

)" is specified in the parameter list, data is output.

Net "kg" (+) N , + 0 0 1 2 . 3 4 5 k g

CR LF

Tare data "kg" T

, + 0 0 0 2 . 0 0 0 k g

CR LF

Example of preset tare function

Net "kg" (+) N

, + 0 0 1 2 . 3 4 5 k g

CR LF

Preset tare data "kg" P T , + 0 0 0 2 . 0 0 0 k g

CR LF

Data output mode

Command mode

The scale is controlled by commands that come from an external device such as a computer.

For details, refer to "16.5.1. Command Mode".

Stream mode (

)

Specify or in the function table. Data is output continuously. The data

update rate is approximately 10 times per second, the same as the display refresh rate. The stream mode does not output data during the setting procedures.

Page 68

Page 66 HV/HW-C/CP Series

Print key mode (

)

Specify , or in the function table. When the weighing value

is stable, data is output by pressing the PRINT key. At this time, the display flashes once to indicate that the data is output.

Auto-print mode + data (

)

Specify , or in the function table. When the weighing value

is stable at +5d and above, the data is output. The next transmission can occur after the weighing value falls to +4d or below.

Auto-print mode +/- data (

)

Specify

, or in the function table. When the weighing value is stable at +5d and above or -5d and below, the data is output. The next transmission can occur after the weighing value falls between -4d and +4d.

Auto-print mode + data and OK (

)

Specify , or in the function table. When the weighing value

is stable and OK as a comparison result at +5d and above, the data is output. The next transmission can occur after the weighing value falls to +4d or below.

Auto-print mode +/- data and OK (

)

Specify , or in the function table. When the weighing value

is stable and OK as a comparison result at +5d and above or -5d and below, the data is output. The next transmission can occur after the weighing value falls between -4d and +4d.

"d" means "digit" to be equivalent to minimum weighing value in the unit "kg".

Baud Rate

Select the proper baud rate according to the device to be connected to the HVW-03C.

When the AD-8121B printer is connected, specify the baud rate to 2400 bps at "Baud rate 1

" or "Baud rate 2 " in the function table.

When the AD-8127 printer is connected, specify the baud rate to 2400, 4800 or 9600 bps at

"Baud rate 1 , or " or "Baud rate 2 , or " in the function table.

If using 2400 bps, set for the device connected at OP-ch1.

If using 2400 bps, set for the device connected at OP-ch2.

If using 4800 bps, set for the device connected at OP-ch1. If using 4800 bps, set for the device connected at OP-ch2.

If using 9600 bps, set for the device connected at OP-ch1. If using 9600 bps, set for the device connected at OP-ch2.

Page 69

HV/HW-C/CP Series Page 67

16.5.1. Command Mode

In the command mode, the scale is controlled by commands that come from an external device such as a computer.

Command List

Command Description Remarks

Q Requests data output immediately.

Z Zeros the scale when the weighing value is stable. Same as the ZERO key. T Tares the scale when the weighing value is stable. Same as the TARE key. U Switches the weighing unit. Same as the MODE key.

CT Clears tare

PT Sets preset tare PT,+000000

LF A Outputs accumulation values N Outputs the number of accumulations

CA Clears accumulation

ID Sets the ID number ID:xxxxxx

LF ?ID Requests the ID number ?PT Outputs the preset tare value

?H3

In five-level comparator mode : Not used In three-level comparator mode : Not used In seven-level comparator mode : Threshold value of rank 5

is output.

?H2

In five-level comparator mode : HIHI limit value is output. In three-level comparator mode : HI limit value is output. In seven-level comparator mode : Threshold value of rank 4

is output.

?H1

In five-level comparator mode : HI limit value is output. In three-level comparator mode : Not used In seven-level comparator mode : Upper threshold value of

rank 3 is output.

?L1

In five-level comparator mode : LO limit value is output. In three-level comparator mode : Not used In seven-level comparator mode : Lower threshold value of

rank 3 is output.

?L2

In five-level comparator mode : LOLO limit value is output. In three-level comparator mode : LO limit value is output. In seven-level comparator mode : Threshold value of rank 2

is output.

?L3

In five-level comparator mode : Not used In three-level comparator mode : Not used In seven-level comparator mode : Threshold value of rank 1

is output.

The output of setting values for comparator mode

Five-level :

Three-level :

Seven-level :

Page 70

Page 68 HV/HW-C/CP Series

Command Description Remarks

In five-level comparator mode : Not used In three-level comparator mode : Not used In seven-level comparator mode : The threshold value of

rank 5 is stored.

In five-level comparator mode : HIHI limit value is stored. In three-level comparator mode : HI limit value is stored. In seven-level comparator mode : The threshold value of

rank 4 is stored.

In five-level comparator mode : HI limit value is stored. In three-level comparator mode : Not used In seven-level comparator mode : The upper threshold value

of rank 3 is stored.

In five-level comparator mode : LO limit value is stored. In three-level comparator mode : Not used In seven-level comparator mode : The lower threshold value

of rank 3 is stored.

In five-level comparator mode : LOLO limit value is stored. In three-level comparator mode : LO limit value is stored. In seven-level comparator mode : The threshold value of

rank 2 is stored.

In five-level comparator mode : Not used In three-level comparator mode : Not used In seven-level comparator mode : The threshold value of

rank 1 is stored.

The input of setting values for comparator mode

Input the six-digit value excluding the polarity and decimal point.

Page 71

HV/HW-C/CP Series Page 69

Command Examples

The examples below are for the function setting (Reply to commands). The character means "Space (20h)".

To request data output immediately.

Command Q CR LF

Reply S T , + 0 0 1 2 . 3 4 5 k g

CR LF Stable positive data

U S , + 0 0 0 7 . 8 9 0 k g

CR LF Unstable positive data

O L , + 9 9 9 9 . 9 9 9 k g

CR LF display

To zero the weighing value when the weighing value is stable.

Zero point is set when the scale is in a condition where zero operation is possible.

Command Z

CR LF

Reply Z

CR LF Zero point has been set. (No reply If is set.)

To tare the weighing value when the weighing value is stable.

Net value is displayed when the scale is in a condition where tare operation is possible.

Command T

CR LF

Reply T

CR LF Net value has been displayed. (No reply If is set.)

To switch the weighing unit.

The weighing unit is switched.

Command U

CR LF

Reply U

CR LF No reply If is set.

To cancel tare value.

The weighting value becomes the gross and the net mark is turned off. The tare value becomes zero.

Command C T

CR LF

Reply C T

CR LF This command has been executed.

To set preset tare.

Tare value is set and the net is displayed. Tare value is a numerical value of 6 digits with a

polarity sign and does not contain a decimal point.

Te m p la t e P T , [ parameter ]

Command P T , + 0 0 0 1 2 0

CR LF

Reply P T , + 0 0 0 1 2 0

CR LF

To output accumulation values.

Command A

CR LF

Reply A , + 0 0 1 2 . 3 0 0 k g

CR LF

Page 72

Page 70 HV/HW-C/CP Series

To output the number of accumulations.

Command N

CR LF

Reply N , + 0 0 0 0 0 1 4 0

CR LF

To clear accumulation.

Accumulated data and number of accumulations are set to zero.

Command C A

CR LF

Reply C A

CR LF

To set the ID number.

The ID number is numerical value and alphabet characters of 6 digits and does not contain a

decimal point.

Te m p la t e I D : [ parameter ]

Command I D : A B C 1 2 3

CR LF

Reply I D : A B C 1 2 3

CR LF

To request the ID number.

The ID number is output.

Command ? I D

CR LF

Reply I D : A B C 1 2 3

CR LF

To output the preset tare value.

The preset tare value is output.

Command ? P T

CR LF

Reply P T , + 0 0 0 0 , 1 2 0 k g

CR LF

To output H3 value.

Five-level comparator mode

.............

Not used

Three-level comparator mode

..........

Not used

Seven-level comparator mode .........Threshold value of rank 5 is output.

Command ? H 3

CR LF

Reply H 3 , + 0 0 0 5 0 0

CR LF

To output H2 value.

Five-level comparator mode

.............

HIHI limit value is output.

Three-level comparator mode

..........

HI limit value is output.

Seven-level comparator mode .........Threshold value of rank 4 is output.

Command ? H 2 CR LF Reply H 2 , + 0 0 0 4 0 0

CR LF

Page 73

HV/HW-C/CP Series Page 71

To output H1 value.

Five-level comparator mode

.............

HI limit value is output.

Three-level comparator mode

..........

Not used

Seven-level comparator mode......... Upper threshold value of rank 3 is output.

Command ? H 1 CR LF Reply H 1 , + 0 0 0 3 0 0

CR LF

To output L1 value.

Five-level comparator mode

.............

LO limit value is output.

Three-level comparator mode

..........

Not used

Seven-level comparator mode .........Lower threshold value of rank 3 is output.

Command ? L 1 C

R LF

Reply L 1 , + 0 0 0 2 0 0

CR LF

To output L2 value.

Five-level comparator mode

.............

LOLO limit value is output.

Three-level comparator mode

..........

LO limit value is output.

Seven-level comparator mode .........Threshold value of rank 2 is output.

Command ? L 2 C

R LF

Reply L 2 , + 0 0 0 1 0 0

CR LF

To output L3 value.

Five-level comparator mode

.............

Not used

Three-level comparator mode

..........

Not used

Seven-level comparator mode .........Threshold value of rank 1 is output.

Command ? L 3 CR LF Reply L 3 , + 0 0 0 0 0 0

CR LF

To set H3 value.

Five-level comparator mode

.............

Not used

Three-level comparator mode

..........

Not used

Seven-level comparator mode .........The threshold value of rank 5 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e H 3 , [ parameter ]

Command H 3 , + 0 0 0 5 0 0

CR LF

Reply H 3 , + 0 0 0 5 0 0

CR LF

No reply If is set.

Page 74

Page 72 HV/HW-C/CP Series

To set H2 value.

Five-level comparator mode

.............

HIHI limit value is stored. Three-level comparator mode

..........

HI limit value is stored.

Seven-level comparator mode .........The threshold value of rank 4 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e H 2 , [ parameter ]

Command H 2 , + 0 0 0 4 0 0

CR LF

Reply H 2 , + 0 0 0 4 0 0

CR LF

No reply If

is set.

To set H1 value.

Five-level comparator mode

.............

HI limit value is stored. Three-level comparator mode

..........

Not used

Seven-level comparator mode .........The upper threshold value of rank 3 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e H 1 , [ parameter ]

Command H 1 , + 0 0 0 3 0 0

CR LF

Reply H 1 , + 0 0 0 3 0 0

CR LF

No reply If is set.

To set L1 value.

Five-level comparator mode

.............

LO limit value is stored. Three-level comparator mode

..........

Not used

Seven-level comparator mode .........The lower threshold value of rank 3 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e L 1 , [ parameter ]

Command L 1 , + 0 0 0 2 0 0

CR LF

Reply L 1 , + 0 0 0 2 0 0

CR LF

No reply If is set.

To set L2 value.

Five-level comparator mode

.............

LOLO limit value is stored. Three-level comparator mode

..........

LO limit value is stored.

Seven-level comparator mode .........The threshold value of rank 2 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e L 2 , [ parameter ]

Command L 2 , + 0 0 0 1 0 0

CR LF

Reply L 2 , + 0 0 0 1 0 0

CR LF

No reply If is set.

To set L3 value.

Five-level comparator mode

.............

Not used Three-level comparator mode

..........

Not used

Seven-level comparator mode .........The threshold value of rank 1 is stored.

Input the parameter of 6 digits excluding the polarity and decimal point.

Te m p la t e L 3 , [ parameter ]

Command L 3 , + 0 0 0 0 0 0

CR LF

Reply L 3 , + 0 0 0 0 0 0

CR LF

No reply If is set.

Page 75

HV/HW-C/CP Series Page 73

Response when or is specified in the function table

If or is used and a command response is active, the following response may be output.

When the Z command is executed with an unstable weighing value and cannot be

finished, the response I is returned.

Command Z

CR LF

Reply I

CR LF The scale is not in a condition that zero operation is possible.

When the scale receives a command that it cannot identify or that does not exist, the

response ? is returned.

Command B

CR LF

Reply ?

CR LF The scale received an undefined command.

Response when or is specified in the function table

or does not use a reply. The undefined command is ignored.

Page 76

Page 74 HV/HW-C/CP Series

16.6.

Using UFC (

Universal Flex Coms

) Function

The UFC function allows you to print out using the format enabled for the printer (UFC format).

The UFC format data can be output through an RS-232C or USB interface.

The scale can store the UFC format as text data. The format can use variable parameters as a

part of text data. Variable parameters can replace with weighing value, tare value and the like when printed out.

The maximum number of text data is 400 characters.

To use the UFC function, it is necessary that the PF command be used and the UFC format

be stored as text data on the scale in advance.

When the PRINT key is pressed or auto-print mode is used, the scale prints the stored text

data after variable parameters is replaced with weighing value, tare value and the like.

Specify , or to use the UFC format in the function table.

Store Text Data to the Scale

Command P F , $ P C , ‘ T E X T ‘ , # 2 0 , $ S P 2 , & $ C R , $ L F , $ W T , $ C R , $ L F

CR LF

Reply P F

CR LF

Terminato

The text data (the UFC format) can sent using the PF command :

Variable parameters for the scale data and control codes

Parameter Scale Data & Control Code Parameter Scale Data & Control Code

$ID ID number $CP Comparator result

$PC Counting number $DT Date for built-in printer Type CP

$WT Current weighing value $TM Time for built-in printer Type CP

$TR Current tare value $CM , Comma (2Ch) $PT Current preset tare value $CR

CR Carriage Return (0Dh)

$TL Accumulation value $LF LF Line Feed (0Ah)

$AN Accumulation count $SP Space (20h)

Note

These parameters must use capital letters.

ASCII text string

Text string is described in single quote marks ' .

The single quote itself is written as tow single quotes.

Example of text Data : 'Data'

Example of text 'Data' : '''Data'''

ASCII hexadecimal code

The ASCII hexadecimal codes are written in the form # and two hexadecimal digits.

This will mainly be used to send control codes that cannot be described as a text string.

Example of EOT of ASCII code : #04

Page 77

HV/HW-C/CP Series Page 75

Data repeated

When the control codes $SP, $CR and $LF can be used with " and a number (of two digits

maximum)", these codes will be repeated the number of times designated.

Example where $LF is repeated 9 times : $LF 9 Example where space is repeated 12 times : $SP 12

Link mark &

If you will send more than 2 lines of data, attach & to the end of the first line. Then, the scale

decides that the data is continued.

As separators for data, a space (20h) or comma (2Ch) , are used.

These separators can be omitted, but you cannot omit the comma (2Ch) , after the PF command. You must start with the PF, command.

Data format for variable parameters (Space (20h) is expressed as .)

Variable parameters of the scale data are replaced with the following data format :

Data is a fixed length that includes a sign and a decimal point.

The leading zeros of data are replaced with spaces (20h) .

$ID of variable parameter Example of ID number : ABC456

6 digits

A B C 4 5 6

$PC of variable parameter Example of counting number : 123 pcs

9 digit counting number + 3 digit unit

+ 1 2 3 P C

$WT of variable parameter Example of the current weighing value : 1.234 kg

9 digit weighing value + 3 digit unit

+ 1 . 2 3 4 k g

$TR of variable parameters Example of the current tare value : 1.234 kg

9 digit tare value + 3 digit unit

+ 1 . 2 3 4 k g

$PT of variable parameter Example of the current preset tare value : 1.234 kg

9 digit preset tare value + 3 digit unit

+ 1 . 2 3 4 k g

$TL of variable parameter Example of accumulation value : 1.234 kg

9 digit accumulation value + 3 digit unit

+ 1 . 2 3 4 k g

Page 78

Page 76 HV/HW-C/CP Series

$AN of variable parameter Example of accumulation count : 123 counts

9 digit accumulation count

+ 1 2 3

$CP of variable parameter Example of HIHI result

3 digits

I 2

Example of HI result

3 digits

I 1

Example of OK result

2 digits

Example of LO result

3 digits

O 1

Example of LOLO result

3 digits

O 2

Example of "not compared"

2 digits

$DT of variable parameter Example of date for built-in printer, Type CP : YYYY / MM / DD .

10 digits

2 0 1 8 / 3 / 1 8

$TM of variable parameter Example of time for built-in printer, Type CP : HH : MM : SS

8 digits

1 2 : 3 4 : 5 6

Printing Example for the PF Command using the AD-8127 Printer

AD-8127 format for The PF Command or Computer Scale

PF,'Weight',$CR,$LF,& $SP 4,$WT,$CR,$LF,& 'CHECK'$CR,$LF,& $SP 4,$CP,$CR,$LF,& $CR,$LF CR LF

Terminator code

$CR

: Carriage return, ASCII 0Dh

$LF

: Line feed, ASCII 0Ah

Note

The UFC format does not send a terminator code automatically.

Therefore, add the terminator code at the end of text data if necessary.

Page 79

HV/HW-C/CP Series Page 77

17.

Specifications

HV-C/CP Series (Weighing capacity of 15 kg to 220 kg)

Models

HV-15KC

HV-15KCP

HV-60KC

HV-60KCP

HV-200KC

HV-200KCP Weighing capacity [kg] 3 6 15 15 30 60 60 150 220 Min. weighing (1 digit) [kg] 0.001 0.002 0.005 0.005 0.01 0.02 0.02 0.05 0.1 Weighing capacity [lb] # 6 15 30 30 60 150 150 300 500 Min. weighing (1 digit) [lb] # 0.002 0.005 0.01 0.01 0.02 0.05 0.05 0.1 0.2 Weighing capacity [oz] # 96 240 480 480 960 2400 2400 4800 8000 Min. weighing (1 digit) [oz] # 0.05 0.1 0.2 0.2 0.5 1 1 2 5 Weighing capacity [lb_oz] # 30 lb Min. weighing (1 digit) [lb_oz] # 0.1 oz

---

Number of samples in counting mode [pieces]

5 (can be changed to 10, 20, 50, 100)

Max. count number [pieces] 150,000 120,000 110,000

Display

7 segment LCD, Character height 26 mm,

3 color 5 level comparator LED, Refresh rate: 10 times per second

Repeatability (

Standard deviation

) [kg] 0.001 0.002 0.005 0.005 0.01 0.02 0.02 0.05 0.1 Linearity [kg] ±0.001 ±0.002 ±0.005 ±0.005 ±0.01 ±0.02 ±0.02 ±0.05 ±0.1 Span drift ±20 ppm/°C typ. (5 °C to 35 °C)

HV-C

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery TYPE D (R20P / R20PU / LR20) x 4

Power source

HV-CP

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery life (HV-C)

Approximately 1200 hours,

when using alkaline battery and setting the display to off.

Ambient temperature and humidity

-10 °C to 40 °C,

Less than 85 %R.H. (Do not allow condensation) Weighing pan size [mm] 250 x 250 330 x 424 390 x 530 Dimensions [mm]

Width x Depth x Height

255 x 494 x 366 330 x 640 x 750 390 x 746 x 750

HV-C 6 11 17

Mass of scale [ kg ]

HV-CP 7 12 18

# : If the law in your area permits, you can use these units.

Page 80

Page 78 HV/HW-C/CP Series

HW-C/CP Series (Weighing capacity of 10 kg to 220 kg)

Models

HW-10KC

HW-10KCP

HW-60KC

HW-60KCP

HW-100KC

HW-100KCP

HW-200KC

HW-200KCP Weighing capacity [kg] 10 60 100 220 Min. weighing (1 digit) [kg] 0.001 0.005 0.01 0.02 Weighing capacity [lb] # 20 150 200 500 Min. weighing (1 digit) [lb] # 0.002 0.01 0.02 0.05 Weighing capacity [oz] # 320 2400 3200 8000 Min. weighing (1 digit) [oz] # 0.05 0.2 0.5 1 Weighing capacity [lb_oz] # 20 lb Min. weighing (1 digit) [lb_oz] # 0.1 oz

---

Number of samples in counting mode [pieces]

5 (can be changed to 10, 20, 50, 100)

Max. count number [pieces] 100,000 120,000 100,000 110,000

Display

7 segment LCD, Character height 26 mm,

3 color 5 level comparator LED, Refresh rate: 10 times per second

Repeatability (

Standard deviation

) [kg] 0.002 0.01 0.02 0.04 Linearity [kg] ±0.002 ±0.01 ±0.02 ±0.04 Span drift ±20 ppm/°C typ. (5 °C to 35 °C)

HW-C

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery TYPE D (R20P / R20PU / LR20) x 4

Power source

HW-CP

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery life (HW-C)

Approximately 1200 hours,

when using alkaline battery and setting the display to off.

Ambient temperature and humidity

-10 °C to 40 °C,

Less than 85 %R.H. (Do not allow condensation) Weighing pan size [mm] 250 x 250 330 x 424 390 x 530 390 x 530 Dimensions [mm]

Width x Depth x Height

255 x 494 x 366 330 x 640 x 750 390 x 746 x 750 390 x 746 x 750

HW-C 6 11 17 17

Power source

HW-CP 7 12 18 18

# : If the law in your area permits, you can use these units.

Page 81

HV/HW-C/CP Series Page 79

HV-C/CP Series (Weighing capacity of 300 kg to 600 kg)

Models

HV-300KC

HV-300KCP

HV-600KC

HV-600KCP Weighing capacity [kg] 150 300 300 600 Min. weighing (1 digit) [kg] 0.05 0.1 0.1 0.2 Number of samples in counting

mode [pieces]

5 (can be changed to 10, 20, 50, 100)

Max. count number [pieces] 60,000 60,000

Display

7 segment LCD, Character height 26 mm,

3 color 5 level comparator LED, Refresh rate: 10 times per second

Repeatability (

Standard deviation

) [kg] 0.05 0.1 0.1 0.2 Linearity [kg] ±0.05 ±0.1 ±0.1 ±0.2 Span drift ±20 ppm/°C typ. (5 °C to 35 °C)

HV-C

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery TYPE D (R20P / R20PU / LR20) x 4

Power source

HV-CP

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery life (HV-C)

Approximately 600 hours,

when using alkaline battery and setting the display to off.

Ambient temperature and humidity

-10 °C to 40 °C,

Less than 85 %R.H. (Do not allow condensation) Weighing pan size [mm] 600 x 700 Dimensions [mm]

Width x Depth x Height

600 x 943 x 942

HV-C 45

Power source

HV-CP 46

# : If the law in your area permits, you can use these units.

Page 82

Page 80 HV/HW-C/CP Series

HW-C/CP Series (Weighing capacity of 300 kg to 600 kg)

Models

HW-300KC

HW-300KCP

HW-600KC

HW-600KCP Weighing capacity [kg] 300 600 Min. weighing (1 digit) [kg] 0.05 0.1 Number of samples in counting

mode [pieces]

5 (can be changed to 10, 20, 50, 100)

Max. count number [pieces] 60,000 60,000

Display

7 segment LCD, Character height 26 mm,

3 color 5 level comparator LED, Refresh rate: 10 times per second

Repeatability (

Standard deviation

) [kg] 0.1 0.2 Linearity [kg] ±0.1 ±0.2 Span drift ±20 ppm/°C typ. (5 °C to 35 °C)

HW-C

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery TYPE D (R20P / R20PU / LR20) x 4

Power source

HW-CP

AC adapter

Please confirm that the AC adapter type is correct for your local voltage and receptacle type. The AC adapter may not be provided for some areas. 50Hz/ 60Hz.

Battery life (HW-C)

Approximately 600 hours,

when using alkaline battery and setting the display to off.

Ambient temperature and humidity

-10 °C to 40 °C,

Less than 85 %R.H. (Do not allow condensation) Weighing pan size [mm] 600 x 700 Dimensions [mm]

Width x Depth x Height

600 x 943 x 942

HW-C 45

Power source

HW-CP 46

# : If the law in your area permits, you can use these units.

Page 83

HV/HW-C/CP Series Page 81

Dimensions

S-models

HV-15KC HV-15KCP HW-10KC HW-10KCP

(494)

255

 43 250 (366)

104

180 35 180 201 250

330

M-models

HV-60KC HV-60KCP HW-60KC HW-60KCP (640)

255

(750)

 43 424

105

240 45 334 187

Unit: mm

Page 84

Page 82 HV/HW-C/CP Series

L-models

HV-200KC HV-200KCP HW-100KC HW-100KCP HW-200KC HW-200KCP

390

(746) 255

 43

(750)

530

129

300 45 440 187

L2-models

HV-300KC HV-300KCP HV-600KC HV-600KCP 600 HW-300KC HW-300KCP HW-600KC HW-600KCP

(943) 255

40 18 (942)

700 146

149  76 506 47 606

Unit: mm

Page 85

HV/HW-C/CP Series Page 83

18.

Maintenance

Refer to "3. Precautions" regarding use. Refer to "14. Calibration (Adjusting the Scale)" regarding precision weighing. Periodically confirm the accuracy of the weighing.

Calibrate the scale, if it has been moved to another location or the environment has changed.

18.1.

Repair

Do not disassemble or assemble the scale without an authorized service engineer. Doing so may cause an electrical shock or damage to the scale. In this case, repair is not covered under warranty. Contact your local A&D dealer if your scale needs service or repair.

18.2.

Check

Points

Before

Calling Maintenance Service

In this situation Confirm these items

Nothing is displayed. Scale does not turn on.

Is the AC adapter properly connected ? Is the AC adapter of the correct voltage ? Are the batteries consumed completely ? Is the battery direction correct ?

Even if the scale turns on, zero cannot be displayed.

Check around the weighing pan. Is there anything on the weighing pan ? Perform zero point calibration.

is displayed

and does not proceed.

The weighing value is unstable due to drift, vibration or other factors.

A breeze or vibration may be affecting the measurement.

Check around the weighing pan. Check the connection of load cell cable. Zero value is not displayed when the display is turned on. Remove

anything that is on the weighing pan. Perform zero point calibration.

is displayed

Calibration error that means "Too heavy".

is displayed

Calibration error that means "Too light".

is displayed

Weighing error that means "Overloaded".

is displayed

Weighing error that means "Underloaded".

Fixed display

Did you use the hold function in the function table ? Turn off the scale and turn it on again.

is displayed

Output voltage of batteries is low. Replace with new ones.

is displayed

Output voltage of the AC adapter is low. Confirm that the type of the

AC adapter is correct.

When the following errors are displayed, shutdown the power once and turn the power on again. If you cannot solve those errors, contact your local dealer.

is displayed

Mass sensor is failed.

is displayed

Temperature sensor is failed.

is displayed

Memory (circuit) is failed.

Page 86

Page 84 HV/HW-C/CP Series

19.

Index

_ _.................................................................................21

Stability mark....................................................20

Battery mark ..................................................... 20

Comparator indicator ............................... 20, 34

?H1 Command, Request H1 value................ 67, 71

?H2 Command, Request H2 value................ 67, 70

?H3 Command, Request H3 value................ 67, 70

?ID Command, Request ID ..................................67

?L1 Command, Request L1 value ................ 67, 71

?L2 Command, Request L2 value ................ 67, 71

?L3 Command, Request L3 value ................ 67, 71

?PT Command, Request preset tare value .........67

_<_ key .......................................................................................... 22

_>_ key .......................................................................................... 22

A Command, accumulation values ..................67

AC adapter ..........................................................9 - 11, 24, 77 - 80

Accessories...................................................................................11

Accumulation count......................................................................30

Accumulation function..................................................................30

Accumulation mode

...........................................53

Accumulation value ......................................................................30

Assembling.................................................................................. 7, 8

Auto-tare .................................................... 38, 52

Tare on initial load .................................... 38, 53

Interval until making automatic tare........ 38, 53

Automatic power off .................................................. 52

Automatic power on

..................................................52

Auto-print mode ..............................................................55 - 57, 66

Auto-tare ................................................. 38, 52

AX-KO2466 RS-232C cable ........................... 12, 62

AXP-3003217D Display unit cover.......................... 9 - 11

AX-PP147-S Roll paper................................11, 12, 39

Back light brightness

.....................................................52

Back light control ..................................................52

Base unit.......................................................................9, 10, 18, 19

Class, Basic functions.............................. 52, 53

Battery....................................................................... 13, 25, 77 - 80

Battery life .............................................................................. 77 - 80

Battery mark

.........................................................20

Baud rate ................................................................................ 54, 66

Bit length, Parity 1 ..................................................54

Bit length, Parity 2 ..................................................54

Baud rate 1 ................................... 54, 66

Baud rate 2 ................................... 54, 66

Bracket cover ..................................................................... 8, 10, 11

Bit length, Parity 1 ........................................... 54

Bit length, Parity 2 ........................................... 54

Bubble spirit level ...........................................................7, 8, 18, 19

Built-in printer communication format .................. 54

Built-in printer label mode ..................................... 57

Built-in printer output mode

..................................... 57

Buzzer .........................37, 53, 63

Buzzer

..................12, 37, 53, 63

CA Command, Clear accumulation.................... 67

Cable clamp............................................................... 10, 11, 14, 16

Cable tie ..............................................................................8, 10, 11

Calibration.................................................. 49, 50

Calibration error.........................................21, 83

_CAL_ switch ............................................................18, 19, 49, 50

Calibration .........................................................................47, 49, 50

Calibration error

...............................21, 83

Calibration test report ................................................. 44

Cap ..................................................................................7, 8, 18, 19

Calibration test report ..................................... 44

Clock adjustment ......................................39, 42

Cleaning ...........................................................................................6

Clock adjustment ...............................39, 42

Command................................................................67 - 71, 74 - 76

Command mode.................................................................... 65, 67

Communication cable ................................................................. 62

Communication format.......................................................... 54, 65

Comparator brightness

........................................... 54

Comparator condition ...........................................32, 54

Comparator indicator .........................20, 34

Comparator mode ...................54, 67, 68, 70, 71

Comparator relay output HVW-04C ..................12, 32, 37, 63

Comparator reversal ............................................ 54

Contact input 1 ............................................53, 63

Contact input 2 ............................................53, 63

Weighing stabilization level.............................. 52

Contact input ...............12, 53, 63

Counting mode.................................................. 20, 28, 29, 77 - 80

Comparator condition................................. 32, 54

Status of LED when turning on display.......... 54

Comparator brightness .................................... 54

Comparator mode ................................32, 38, 54

CT Command, Clear tare....................................... 67

Data communication software WinCT........................... 61

Data format .............................................................................65, 75

Decimal point................................................................................ 52

Page 87

HV/HW-C/CP Series Page 85

Dimensions ........................................................................... 77 - 82

Display ................................................................................... 77 - 80

Display character.......................................................................... 41

Display unit ...................................................................9, 10, 18, 19

Display unit cover AXP-3003217D ........................ 9, 10, 11

Double size .............................................. 39, 57

Class, Data output.............................. 55, 56, 57

Double size ............................................... 39, 57

Overload.................................................... 21, 83

Underload.................................................. 21, 83

Environment........................................................................... 47, 52

Mass sensor error ...........................................83

Templerature sensor error .............................83

Memory error ...................................................83

Extension load cell cable HVW-02 ...............................12

Extension load cell cable HVW-08C ............................12

Ferrite core .......................................................................14, 15, 16

Five-level comparator mode ......................32, 34, 67, 68, 70, 71

Format............................................................43, 45, 46, 54, 65, 74

15 Stand for the display unit ................................12

FW-16-4 Wheel................................................................12

GLP Good Laboratory Practice ..............................41

GMP........................................................... 43, 44

GMP Good Manufacturing Practice................. 41, 43

Gravity acceleration correction ............................................ 47, 49

Grounding the scale .....................................................................17

H1 Command, Set H1 value................................ 68

H2 Command, Set H2 value................................ 68

H3 Command, Set H3 value................................ 68

Hex wrench ................................................................ 7 - 11, 14, 16

Hold condition .................................................. 53

Hold condition ..............................................................53

Hold function .......................................................................... 20, 21

_HOLD_ key.................................................................................22

Hold Hold mark.................................................. 20, 21

C/CP series .................................................................. 3, 7, 41

HVW-02 Extension load cell cable................................ 12

HVW-02CB USB interface......................... 12, 16, 38, 59, 60

HVW-03C RS-232C interface ............................12, 38, 59

HVW-04C Comparator relay output.......................... 12, 59

HVW-08C Extension load cell cable......................... 12, 15

HVW

11C Wall mounting kit .............................................12

HVW-13 Roller conveyor for L-models........................ 12

HVW-14 Roller conveyor for M-models ......................12

HW-C/CP series................................................................. 3, 7, 41

ID number ................................................. 41, 57

ID number ................................... 39, 41, 43 - 46, 55, 56

ID number output ............................................ 55 - 57

ID Command, Set ID number ............................ 67

GMP output 1 .................................................. 55

GMP output 2 .................................................. 56

GMP print......................................................... 57

Installing driver software .............................................................. 60

Item ....................................................................................21, 22, 51

Key lock ........................................................... 52

L1 Command, Set L1 value................................ 68

L2 Command, Set L2 value.......................... 68, 72

L3 Command, Set L3 value.......................... 68, 72

Built-in printer label mode .............................. 57

Low battery ............................................5, 13, 25

Battery output is low voltage.......................... 83

AC adapter output is low voltage .................. 83

Leveling feet....................................................................7, 8, 18, 19

Back light brightness ............................ 52

Line feed of printer .................................................... 57

Linearity ..................................................................................77 - 80

Back light control............................................. 52

Too light unit mass.......................................... 28

Load cell cable......................................................................... 7 - 10

Key lock............................................................ 52

Lower limit ............................................................32, 34, 36, 38, 54

M+ mark ..................................................................................20, 30

_M+_ key ..........................................................................22, 30, 31

Maintenance................................................................................. 83

Malfunction and damage ..................................................5, 25, 60

Mass .............................................................26, 28, 30, 47, 77 - 80

Maximum count number......................................................77 - 80

Minimum display .........................................................4, 21, 36, 65

Minimum weighing......................................................... 21, 77 - 80

_MODE_ key ............................................................................... 22

N Command, Output the count of accumulation ...... 67

Near zero ...................................................................................... 21

NET.......................................................................20, 22, 25, 26, 38

Number of samples ...............................................................28, 29

_ON/OFF_ key ...................................................22, 24, 25, 52, 53

OP-ch1 Option channel 1.......................................54, 59

OP-ch2 Option channel 2.......................................54, 59

OP-ch3 Option channel 3............................................. 59

Option ......................................................................................12, 59

Output mode................................................................... 39, 55 - 65

Paper feed ........................................................................23, 39, 40

Parameter .........................................................................21, 51, 74

Parameter settings....................................................................... 51

Parity.............................................................................................. 54

Unit of counting mode ........................20, 28, 29

Decimal point................................................... 52

Page 88

Page 86 HV/HW-C/CP Series

Automatic power off ........................................52

Pole ...................................................................................14, 18, 19

Automatic power on ........................................52

Power on tare................................................................................25

Power on zero...............................................................................25

Power source........................................................................ 77 - 80

Preset tare PT......................................................... 20, 26, 67

_PRINT_ key................................................................... 22, 39, 66

Printer................................................................................39, 54, 57

Line feed of printer...........................................57

Output mode 1................................................. 55

Output mode 2................................................. 56

Built-in printer output mode ............................57

PT Command, Set preset tare............................. 67

PT mark .................................................................................. 20, 26

Rank..................................................................... 32, 34, 36, 67, 68

Refresh rate........................................................................... 77 - 80

Repair............................................................................................. 83

Repeatability.......................................................................... 77 - 80

Result ..................................................................... 3, 20, 32, 34, 41

Roll paper AX

PP147-S.............................. 11, 12, 39, 40

Roller conveyor FW-18-4............................12

Roller conveyor for L-models HVW-13 .............................12

Roller conveyor for M-models HVW-14 .............................12

RS-232C ............................................................................... 12, 62

RS-232C cable AX-KO2466................................... 12, 62

Stability mark ...........................................................20

_SET_ key .................................................................................... 22

Seven-level comparator mode ...........32, 36, 54, 67, 68, 70, 71

Output ID number to interface 1 ....................55

Output ID number to interface 2 ....................56

Output ID number to printer .................... 39, 57

Class, Communication ................................... 54

Communication format 1................................54

Communication format 2................................54

Built-in printer communication format ...........54

Tare data output during tare........................... 54

Span calibration ..................................................................... 47, 50

Span drift................................................................................ 77 - 80

Stability band time ......................................... 52

Stability band width .................................. 52

Stabilization level ..................................... 52

Stand for the display unit FW-15 .................................... 12

Status of LED when turning on display .................. 54

Stability band width......................................... 52

Add time and date to interface 1 ................... 55

Add time and date to interface 2 ................... 56

Add time and date to built-in printer.............. 57

Stream mode.................................................................. 55 - 57, 65

Stability band time........................................... 52

Accumulation mode .................................30, 39

T Command, Set tare at stable weighing value........ 67

Tare data output during tare

............................. 54

Tare function........................................................20, 22, 25, 26, 38

_TARE_ key.....................................................................20, 22, 26

Tare on initial load ........................................... 53

Three-level comparator mode......32, 34, 36, 54, 67, 68, 70, 71

Time and date adding ..........................................................55 - 57

Title block and End block ............................................................ 45

Zero tracking.................................................... 52

Type C............................................................ 3, 11, 13, 18 - 20, 25

Type CP .................................................................3, 11, 18, 19, 39

U Command, switch the weighing unit ............ 67

UFC format ................................................................................... 74

Unit mass ...................................................................................... 28

Upper limit ..................................................................32, 34, 36, 38

USB ............................................................................................... 60

Variable parameter ...................................................................... 74

Wall mounting kit HVW-11C ........................................ 12

Weighing capacity.......................................................... 47, 77 - 80

Weighing pan ................................................9, 10, 18, 19, 77 - 80

Weighing pan size ................................................................77 - 80

Weight ........................................................................................... 47

Wheel FW

-16-

4......................................................... 12

WinCT Data communication software................................. 61

Z Command, Set zero at stable weighing value....... 67

_ZERO_ key ......................................................................5, 20, 22

Zero point .............................................................20, 22, 25, 47, 50

Zero point mark ................................................................20, 22, 25

Zero tracking ....................................................... 52

Page 89

HV/HW-C/CP Series Page 87

MEMO

Page 90

Page 88 HV/HW-C/CP Series

MEMO

Page 91

Page 92

3-23-14 Higashi-Ikebukuro, Toshima-ku, Tokyo 170-0013, JAPAN Telephone: [81] (3) 5391-6132 Fax: [81] (3) 5391-1566

A&D ENGINEERING, INC.

1756 Automation Parkway, San Jose, California 95131, U.S.A. Telephone: [1] (408) 263-5333 Fax: [1] (408)263-0119

A&D INSTRUMENTS LIMITED

Unit 24/26 Blacklands Way, Abingdon Business Park, Abingdon, Oxfordshire OX14 1DY United Kingdom Telephone: [44] (1235) 550420 Fax: [44] (1235) 550485

A&D AUSTRALASIA PTY LTD

32 Dew Street, Thebarton, South Australia 5031, AUSTRALIA Telephone: [61] (8) 8301-8100 Fax: [61] (8) 8352-7409

A&D KOREA Limited 한국에이.엔.디(주)

서울특별시 영등포구 국제금융로6길33 (여의도동) 맨하탄빌딩 817 우편 번호 07331 ( 817, Manhattan Bldg., 33. Gukjegeumyung-ro 6-gil, Yeongdeungpo-gu, Seoul, 07331 Korea ) 전화: [82] (2) 780-4101 팩스: [82] (2) 782-4264

OOO A&D RUS OOO "ЭЙ энд ДИ РУС"

121357, Российская Федерация, г.Москва, ул. Верейская, дом 17 ( Business-Center "Vereyskaya Plaza-2" 121357, Russian Federation, Moscow, Vereyskaya Street 17 ) тел.: [7] (495) 937-33-44 факс: [7] (495) 937-55-66

A&D INSTRUMENTS INDIA PRIVATE LIMITED

( 509, Udyog Vihar, Phase-

, Gurgaon - 122 016, Haryana, India )

: 91-124-4715555

: 91-124-4715599

BackCover 1WMPD4000058N .