Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display unit
2. 3-in-1 sensor
3. Sensor mounting bracket
4. Mounting hardware
5. Power adapter
6. Instruction Manual
IMPORTANT
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
Register a Product
►
2
Features & Benets
1
4
2
5
3-in-1 SENSOR
1. Temperature & Humidity Sensors
(internal)
2. Release Lever for Battery Access
3. Mounting Point
4. Wind Speed Anemometer
6
3
5. Mounting Hardware
Includes anchors and screws.
Qty Diameter Length
4 #4 1”
1 #6 or #8 1/4” or 3/8”
6. Mounting Bracket
7. A-B-C Switch (not shown)
ID code that must match display’s
A-B-C switch to ensure units
synchronize.
3
Features & Benets
24
23
1
2
3
4
5
6
7
8
9
10
11
12
DISPLAY UNIT
1. Current Outdoor Temperature
Arrow icon indicates the direction the
temperature is trending.
2. Seasonal Information
Wind chill will show when
temperatures are below 40
Dew Point when temperature is 41-
o
79
F (5-26oC), and Heat Index when
temperature is over 80
3. Average Wind Speed
Based on all wind speed readings from
the past 2 minutes.
4. Current Wind Speed
5. Learning Mode Icon
Disappears after weather forecast selfcalibration is complete.
6. 12 to 24 Hour Weather Forecast
Self-Calibrating Forecasting pulls data
from your sensor to generate your
personal forecast.
7. Humidity Level Indicator
Indicates a high or low indoor humidity
level.
8. Current Indoor Temperature
Arrow icon indicates the direction the
temperature is trending.
9. Today Icon
Indicates viewing high/low records
since midnight.
o
F (4oC),
o
F (27oC).
22
21
20
19
18
17
16
15
14
13
10. Moon Phase
11. All-Time Icon
Indicates viewing All-Time records
12. Icon
Indicates SET mode.
13. Backlight Button
14. Intelli-Time® Clock
Automatically updates itself for
Daylight Saving Time.
15. AUTO DIM Mode Indicator (page 8)
16. Display Low Battery Indicator
17. Date
18. Current Indoor Humidity
Arrow icon indicates the direction
the humidity is trending.
19. Storm Indicator
Indicates a rapid drop in pressure and
probable storms.
20. Barometric Pressure
Arrow icon indicates the direction the
pressure is trending.
21. Peak Wind Speed
Highest speed from past 60 minutes.
22. Current Outdoor Humidity
Arrow icon indicates the direction
the humidity is trending.
23. Outdoor Sensor Signal Strength
24. Sensor Low Battery Indicator
4
Features & Benets
1
2
3
4
5
7
8
6
BACK OF DISPLAY UNIT
1. Button
for setup preferences.
2. Button
for setup preferences.
3. Button
for setup preferences.
4. Button
Press to access all-time high and low
records.
9
5. Battery Compartment
6. Plug-in for Power Adapter
7. A-B-C Switch
ID code that must match sensor’s A-B-C
switch to ensure units synchronize.
8. Reset Button
Full reset to factory defaults.
9. Power Adapter
10. Battery Compartment Cover
(not shown)
5
SETUP
3-IN-1 Sensor Setup
Set the A-B-C Switch
1
The A-B-C switch is located inside
the battery compartment. It can be
set to A, B or C. However, you must
select the same letter choices for
both the sensor and the display unit
in order for the units to synchronize.
2
Install or Replace Batteries
AcuRite recommends high quality
alkaline or lithium batteries for the
best product performance. Heavy
duty or rechargeable batteries are
not recommended.
The 3-in-1 sensor requires lithium
batteries in low temperature
conditions. Cold temperatures can
cause alkaline batteries to function
improperly. Use lithium batteries in
the 3-in-1 sensor for temperatures
below -4ºF / -20ºC.
1. Press the release lever and pull
off the lower housing of the
sensor.
2. Remove the battery compartment
cover. Take note of the A-B-C
switch setting inside the battery
compartment.
3. Insert 4 x AA batteries into the
battery compartment, as shown.
Follow the polarity (+/-) diagram
in the battery compartment.
4. Replace the battery cover and
lower housing of the sensor.
A B C
A-B-C Switch
1
set to match
display unit
2
6
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.