Acu-Rite 13001, 13002 User Manual

Instruction Manual

Intelli-Time® Alarm Clock

model 13001 / 13002

CONTENTS

Unpacking Instructions ........... 2

Package Contents .................. 2

Product Registration ............... 2

Features & Benets ................. 3

Clock Setup ........................... 4

Intelli-Time® Clock .................. 4

Set the Time & Date ............... 4

Using the Alarm Clock ............ 5

Troubleshooting ..................... 6

Care & Maintenance .............. 6

Replace Intelli-Time

Specications ......................... 7

FCC Information .................... 7

Customer Support .................. 7

Warranty............................... 8

®

Battery ... 6

Questions? Contact Customer Support at

[phone] or visit www.AcuRite.com.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.

Unpacking Instructions

Remove the protective lm that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.

Package Contents

1. Alarm clock

2. Instruction Manual

IMPORTANT

PRODUCT REGISTRATION

Register online

to receive 1 year

warranty protection

www.AcuRite.com

PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

Register a Product

►

2

Features & Benets

FRONT OF CLOCK

1. PM Indicator

2. ALARM ON Indicator

1

3 4 5 6 7 8 9

2

14

ON OFF

DST

TOP OF CLOCK

3. ALARM Button

4. - BACKWARD Button

5. SNOOZE Button

6. ALARM ON/OFF Switch

7. TIME ZONE Selection
Switch

8. + FORWARD Button

9. TIME SET Button

BOTTOM OF CLOCK

10. Reset Button

11. Battery Compartment

12. Intelli-Time® Battery

13. Intelli-Time® Battery
Compartment Cover

14. DST ON/OFF Switch

10 11

13

12

3

SETUP

Clock Setup

Plug the power cord into power outlet.

Intelli-Time® Clock

Intelli-Time clock and calendar are pre-programmed to the correct time and
date, and update automatically for Daylight Saving Time. All you need to do is
select your time zone using the “TIME ZONE” switch.

Set the Time & Date

Choose the correct time zone (HAST AKST PST MST CST EST AST) using the
“TIME ZONE” switch on the top of the clock.

Set Daylight Saving Time ON or OFF using the “DST ON/OFF” switch on the
bottom of the clock.*

Press and hold the “TIME SET” button for 3 seconds to enter the SET MODE.
Once in the SET MODE the preference you are currently in will blink on the clock.

To adjust the currently selected (ashing) item, press and release the
“+ FORWARD” or “- BACKWARD” buttons (press and HOLD to fast adjust). To

save your adjustments, press and release the “TIME SET” button to adjust the
next preference. The preference order is as follows:

CLOCK HOUR (Please note PM Indicator light)
CLOCK MINUTE
CLOCK MONTH
CALENDAR DATE
CALENDAR YEAR

You will automatically exit SET MODE if no buttons are pressed
for 5 seconds. Enter SET MODE any time by pressing and holding
“TIME SET” button for 3 seconds.

*If you live in an area that observes daylight saving time, DST should be set
to ON.

4

OPERATION

Using the Alarm Clock

Set the Alarm Time

To set alarm time, press and release the “ALARM” button to enter ALARM SET

MODE.

To adjust the currently selected (ashing) item, press and release the
“+ FORWARD” or “- BACKWARD” buttons (press and HOLD to fast adjust).

To save your adjustments, press and release the “ALARM“ button to adjust the

next preference. The preference set order is as follows:

ALARM CLOCK HOUR (Please note PM Indicator light)
ALARM CLOCK MINUTE

You will automatically exit ALARM SET MODE if no buttons are pressed
for 5 seconds. Enter ALARM SET MODE at any time by pressing the
“ALARM“ button.

Alarm Clock ON or OFF Function

To turn alarm on: Slide the “ALARM” switch to “ON”. The Alarm On indicator
will appear next to the word “ALARM” on the screen.

To turn alarm off: Slide the “ALARM” switch to “OFF”. The Alarm On indicator
will disappear next to the word “ALARM” on the screen.

Alarm Clock SNOOZE Function

The alarm will sound for 60 minutes before turning off when no button is
pressed. When the alarm is sounding, activate the 8 minute SNOOZE function
by pressing the SNOOZE button on top of the alarm clock. SNOOZE function
can be activated up to 10 times before the alarm will no longer sound.

5

Troubleshooting

Clock won’t turn on

or displays partial

numbers

Blinking Colon (dots)

• Reset the unit by pressing the reset button located on
the bottom of the clock. This will reset the alarm to the
original factory settings. Time and date will need to be
entered after a reset.

• Blinking of the dots is a way that the seconds are
counted. There is no way to stop the dots from blinking.

If your AcuRite product does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
[phone] for assistance.

Care & Maintenance

Clock Care

Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.

Replace Intelli-Time Clock Battery

Intelli-Time technology is powered
by a pre-installed coin-cell battery
that stores the time and date
settings. The battery has a shelf life
of several years. To replace the
Intelli-Time battery:

1. Locate the coin cell battery

compartment door on the bottom
of the clock. Unscrew and remove
the compartment cover.

2. Insert 1 x CR2032 coin
cell battery into the battery
compartment, as shown. Install
battery with “+” positive terminal
facing OUT.

3. Screw in the battery cover.

CR2032

3V

+

6

Specications

POWER

Power cord (120V)

FCC Information

This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment.
Such modications could void the user authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.

-

Customer Support

AcuRite customer support is committed to providing you with best-in­class service. For assistance, please have the model number of this
product available and contact us in any of the following ways:

[phone] [e-mail]

24/7 support at www.AcuRite.com

► Installation Videos ► Register your Product

► Instruction Manuals ► Support User Forum

► Replacement Parts ► Submit Feedback & Ideas

IMPORTANT

PRODUCT REGISTRATION

Register online

to receive 1 year

warranty protection

www.AcuRite.com

PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE

Register a Product

►

7

Limited One Year Warranty

At AcuRite, we proudly uphold our commitment

to quality technology. Chaney Instrument Co.

warrants that all products it manufactures to
be of good material and workmanship, and to
be free of defects when properly installed and
operated for a period of one year from the date
of purchase.

We recommend that you visit us at
www.AcuRite.com for the fastest way to register
your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain

warranty benets.

Chaney Instrument Co. warrants that all products it manufactures
to be of good material and workmanship, and to be free of
defects when properly installed and operated for a period of
one year from the date of purchase. Remedy for breach of this
warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE
YEAR from date of sale will, upon examination by Chaney,
and at its sole option, be repaired or replaced by Chaney.
Transportation costs and charges for returned goods shall
be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This

warranty will not be breached, and Chaney will give no credit
for products it manufactures which have received normal wear
and tear, been damaged (including by acts of nature), tampered,
abused, improperly installed, damaged in shipping, or repaired
or altered by others than authorized representatives of Chaney.

The above-described warranty is expressly in lieu of all other
warranties, express or implied, and all other warranties are
hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty

of tness for a particular purpose. Chaney expressly disclaims
all liability for special, consequential or incidental damages,

whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Chaney further disclaims all
liability from personal injury relating to its products to the extent

permitted by law. By acceptance of any of Chaney’s products,
the purchaser assumes all liability for the consequences arising
from their use or misuse. No person, rm or corporation is

authorized to assume for Chaney any other liability in connection

with the sale of its products. Furthermore, no person, rm or

corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and signed by a duly authorized agent of Chaney. This warranty

gives you specic legal rights, and you may also have other

rights which vary from state to state.

For in-warranty claims: Chaney Instrument Co.

965 Wells St., Lake Geneva, WI 53147

Weather

Stations

Temperature

& Humidity

Weather

Alert Radio

Kitchen

Thermometers

& Timers

It’s more than accurate, it’s

AcuRite offers an extensive assortment of precision instruments,

designed to provide you with information you can depend on to

Printed in China

13001 INST 121714

Plan your day with condence

©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark

of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and

copyrights are the property of their respective owners. AcuRite uses patented

technology. Visit www.AcuRite.com/patents for details.

.

™

Clocks