ACTi E48 User Manual
Bullet Camera
Hardware Manual
E48
Ver. 2015/03/31
www.acti.com
Hardware Manual
Table of Contents
Precautions 4
Safety Instructions ........................................................................... 6
Introduction 7
List of Models .................................................................................... 7
Package Contents ............................................................................. 8
Physical Description ........................................................................ 9
Installation Procedures 10
Step 1: Prepare for Installation ...................................................... 10
Step 2: Mount the Camera.............................................................. 11
Step 3: Waterproof and Connect the Cable(s) .............................. 13
How to Use the Cable Gland ........................................................ 14
How to Use the Conduit Gland ..................................................... 18
Step 4: Connect to Network ........................................................... 22
Step 5: Access the Camera Live View ........................................... 22
Step 6: Complete the Installation .................................................. 22
Other Cable Connections (Optional) 23
How to Connect DI/DO Devices ..................................................... 23
How to Connect Audio Devices ..................................................... 27
Other Adjustments and Accessories 28
How to Adjust the Viewing Angle and Focus ............................... 28
How to Attach the Sunshield ......................................................... 30
How to Open the Back Cover ......................................................... 31
How to Close the Back Cover ...................................................... 31
How to Insert the Memory Card ..................................................... 33
How to Remove the Memory Card ............................................... 33
2
www.acti.com
Hardware Manual
How to Reset the Camera............................................................... 34
Accessing the Camera 35
Configure the IP Addresses ........................................................... 35
Using DHCP Server to Assign IP Addresses ................................ 35
Using the Default Camera IP Address .......................................... 37
Access the Camera ......................................................................... 39
3
www.acti.com
Hardware Manual
Precautions
Read these instructions
You should read all the safety and operating instructions before using this product.
Heed all warnings
You must adhere to all the warnings on the product and in the instruction manual. Failure to
follow the safety instruction given may directly endanger people, cause damage to the system
or to other equipment.
Servicing
Do not attempt to service this video device yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Trademarks
All names used in this manual are probably registered trademarks of respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. We cannot be held responsible for any
typographical or technical errors and reserve the right to make changes to the product and
manuals without prior notice.
4
www.acti.com
Hardware Manual
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
European Community Compliance Statement
This product has been tested and found to comply with the limits for Class B
Information Technology Equipment according to European Standard EN 55022
and EN 55024. In a domestic environment, this product may cause radio interference in which
cause the user may be required to take adequate measures.
5
www.acti.com
Hardware Manual
Safety Instructions
Cleaning
Disconnect this video product from the power supply before cleaning.
Attachments
Do not use attachments not recommended by the video product manufacturer as they may
cause hazards.
Don’t use accessories not recommended by the manufacturer
Install other devices (such as PoE injector, alarm, etc.) that will be used with the camera in a
dry place protected from weather.
Servicing
Do not attempt to service this video product yourself as opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
Damage Requiring service
Disconnect this video product from the power supply immediately and refer servicing to
qualified service personnel under the following conditions.
1) When the power-supply cord or plug is damaged
2) If liquid has been spilled, or objects have fallen into the video product.
3) If the video product has been directly exposed to rain or water.
4) If the video product does not operate normally by following the operating Instructions in
this manual. Adjust only those controls that are covered by the instruction manual, as an
improper adjustment of other controls may result in damage, and will often require
extensive work by a qualified technician to restore the video product to its normal
operation.
Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to
perform safety checks to determine if the video product is in proper operating condition.
6
www.acti.com
E48
10MP Bullet with D/N, Adaptive IR, Basic WDR, Vari-focal lens
Hardware Manual
Introduction
List of Models
This hardware manual contains the following models:
7
www.acti.com
Package Contents
Camera
Bracket Plate
Sunshield
Drill Template
Mounting Screw Kit
Sunshield Screw Kit
Conduit Gland
Cable Gland
Washers x 2
Terminal Block
Quick Installation Guide
Warranty Card
Drill Template
Hardware Manual
NOTE: The above pictures are for reference only; actual items may slightly vary.
8
www.acti.com
Physical Description
Item
Description
1
Memory Card Slot
Insert a memory card into this slot for local recording purposes.
See How to Insert the Memory Card on page 33 for more
information.
NOTE: Supports microSDHC and microSDXC cards.
2
Reset Button
Restores the factory default settings of the camera. Resetting the
camera must be done while the power is on. See How to Reset
the Camera on page 34 for more information.
3
Power LED
The Power LED turns on when the camera is powered on and
goes off once the initial boot up process is complete.
4
Audio Input
This jack connects to an audio input device, such as a
microphone with built-in amplifier.
NOTE: Make sure that the connected audio input device has a
built-in amplifier. Connecting an ordinary microphone will dwarf
sounds and will result in inaudible recording.
5
Audio Output
This jack connects to an audio output device, such as a speaker.
6
Digital Input / Output
(DI/DO)
This connector connects to digital input or output devices, such as
an alarm trigger, panic button, etc. Digital Input (DI) and Digital
Output (DO) devices are used in applications like motion
detection, event triggering, alarm notifications, etc. See How to
Connect DI/DO Devices on page 23 for more information.
7
Ethernet Port
The Ethernet port connects to a network using a standardard
Ethernet cable.
Hardware Manual
9
www.acti.com
Hardware Manual
Installation Procedures
Step 1: Prepare for Installation
1. If necessary, install a memory card into the memory card slot of the camera. See How to
Insert the Memory Card on page 33 for detailed instructions.
2. Attach the bracket to the camera.
3. Attach the supplied drill template sticker on the ceiling or wall where the camera will be
installed.
4. Drill three (3) screw holes based on the drill template.
5. If connecting digital input or output device, such as alarms, sensors, etc., to the camera,
prepare the terminal block for connection. See How to Connect DI/DO Devices on page
23 for detailed instructions.
6. Determine whether the camera cable will go through the surface or be routed along the
surface.
If the camera cable will go through a hole on the surface, do the following:
a. Drill the cable hole (based on the drill template) on the surface.
b. Route the cable(s) from the network side through the hole on the surface.
10
www.acti.com
Hardware Manual
c. Connect the cables, see Step 3: Waterproof and Connect the Cable(s) on page 13.
d. Push the cable(s) into the cable hole of the surface, then proceed to Step 2: Mount
the Camera on page 11.
If the camera cable will be routed along the surface, continue with the next step.
Step 2: Mount the Camera
NOTE: For simplicity of documentation, the succeding illustrations show the camera as
mounted on the ceiling. Same procedures apply for mounting the camera on the wall.
1. Route the cable:
If the cable will go through a hole on the surface, push the cable(s) through the
hole on the surface.
If the cable will go along the surface, route the cable through the gap on the
bracket.
2. Tighten the set screw on the bracket plate to fixed its position.
3. Attach the camera to the surface using the three (3) supplied screws.
11
www.acti.com
Hardware Manual
4. Adjust the camera installation angle and orientation, and then tighten the screws to fix the
position.
Set Installation Angle Set Viewing Orientation
12
www.acti.com
Bundled Accessory
Description
Cable Gland
Use this solution when connecting an Exterior-grade
Ethernet cable between the camera and a
Power-over-Ethernet (PoE) switch or injector. See How
to Use the Cable Gland on page 14.
Conduit Gland
Use this solution when connecting a standard indoor
Ethernet cable between the camera and a
Power-over-Ethernet (PoE) switch / injector. A flexible
conduit (trade size 1/2”) is required to house the Ethernet
cable. See How to Use the Conduit Gland on page 18.
NOTE: The flex conduit is not included in the package
and must be purchased separately.
Hardware Manual
Step 3: Waterproof and Connect the Cable(s)
NOTE: The succeeding pictures are for reference only; actual connectors may slightly differ.
The camera and the pre-installed network cable, “pigtail”, are resistant to salt, water, weak acid,
alcohol, oil, grease and other common solvents. However, users must ensure that the cable
connection and the network side cable itself are also protected from different environmental
factors.
For Ethernet connection, there are two waterproofing methods.
When connecting input or output devices, such as alarms, sensors, microphones, etc.,
connect the terminal block and/or the audio jack(s) to the camera before connecting to the
network. See Other Cable Connections on page 23 for detailed instructions.
13
Loading...