ACT ACTPRO200 Installation

ACTpro200 Installation

2 Door Controller and Monitored Power Supply

Mains Present

Fuse OP2 Blown

Fuse OP1 Blown

Fuse OP1

Fuse OP2

Press to
connect batteries

MAINS VOLTAGE

DISCONNECT BEFORE MAINTENANCE

LED Functionality:
Red LED indicates the status of communications with the controller.
While online to the controller the Red LED will flash rapidly.
If there is a problem it will flash slowly (about once a second).
Green LED will flash if an event occurs on the ACTpro200.

Secondary AC Fuse

12V 0V

OUTPUT 1

AC AC

12V 0V

OUTPUT 2

5A 250VAC

5A 30VDC

BATTERY 1

Battery OK LEDs

5A 250VAC
5A 30VDC

BATTERY 2

TAMPER

1 2 3 4 5 6 7 8

On

WARNING:

NO C NC NO C NC

5A 250VAC
5A 30VDC

5A 250VAC

5A 30VDC

NC C NO NC C NO

5A 250VAC

5A 30VDC

5A 250VAC
5A 30VDC

Entry/Exit Reader

DOOR 1
Connections

+12V

GREEN

RED0V+5V

SENSE

CLOCK

DATA

+5V0VRED

NETWORK

A

B

0V

0V

Total Length max 1.4km
Belden 9502 or equiv.

DATA

CLOCK

SENSE

OP3

OP2

0V

AUX
INPUT

DC2

PB2

A

B

0V

OP3

OP2

0V

AUX
INPUT

DC2

PB2

GREEN

+12V

Cable: 8 Core Screened
Belden 9504 or equiv

ACT 2000

A
B

Shield

DOORS

A
B

DOORS
NETWORK

DOOR 2
Connections

Entry Reader

Battery 1 - Backup for
Output 1 and PCB

*Always connect Battery 1.

Important!
Do not reverse battery leads.

red lead connects to + terminal of battery
black lead connects to - terminal of battery.

5

Door
Address

Example:
When the dipswitch is set to 3, Door 1 is set to Address 3 and Door 2 is set to Address 4.
When the dipswitch is set to 4, Door 1 is set to Address 4 and Door 2 is set to Address 5.

4

03 OFF OFF OFF ON ON

04 OFF OFF ON OFF OFF

05 OFF OFF ON OFF ON

06 OFF OFF ON ON OFF

07 OFF OFF ON ON ON

08 OFF ON OFF OFF OFF

09 OFF ON OFF OFF ON

10 OFF ON OFF ON OFF

11 OFF ON OFF ON ON

12 OFF ON ON OFF OFF

13 OFF ON ON OFF ON

14 OFF ON ON ON OFF



15 OFF ON ON ON ON

16 ON OFF OFF OFF OFF

6

8

7

FACTORY DEFAULT
This unit should be reset to its
factory default condition before
installation. To do this, power
the unit up with ALL switches in
the OFF position. The two LED's
will illuminate for about 2 sec.
The correct switch settings may
then be set.

Battery 2 - Backup for Output 2
Monitoring for battery 2
can be disabled
by setting dipswitch 3 to ON

www.accesscontrol.ie

Important !
Always Place Varistor
Across Lock Terminals

This illustration shows wiring
for a normally energised
lock. If a normally de-energised
lock is required, use the
N/O relay contacts.

Technical Specifications

Mains Voltage  230Vac +10% -15%

Frequency   47-63 Hz

Mains Fuse  630mAmp

Secondary AC Fuse 3.15Amps

Fuse OP1   1.25 Amps Quick

Fuse OP2   1.25 Amps Quick

Ripple Voltage  <200mV

ACTWinPro users must tick Mains

Fault Reporting in the door view

Access Control Technology, Ireland. Tel: + 353 466 2570

Max length:
30m from +5V
100m from +12V

White
Green
Blue
Red
Black
Brown
Yellow
Orange

For Clock and Data Readers, wire exit
reader in parallel but do not connect
to SENSE.

For Wiegand Readers, wire DATA0 of
the exit reader to SENSE.

SENSE
CLOCK / DATA 1
DATA / DATA 0
+5V or +12V
0V
RED
GREEN
(Buzzer Control)