Operating Instructions which are available from the distributor.
Note: To Program the advanced features of the ACT1000/2000 use the
. Use X to exit from the menu.
. Batch Accepted is displayed
. Enter the user number to be assigned to the first card
. Swipe the last card in the batch.
. Swipe the first card in the batch.
. Press ü to allow the first card in the batch to be programmed.
. Use 0 to scroll to an unused batch.
. Press ü to enter Batch Cards menu
. Use 0 to scroll to Batch Cards menu.
. Press ü to enter the user set-up menu.
. Enter operator code.
6. Entering a batch of cards onto controller.
. Use X to exit from the menu.
. User number Accepted is displayed.
. Swipe the card which you want learned for selected user.
. Press ü to allow the selected user to be learned.
. Use 0 to scroll to the user number which is required.
. Press ü to enter learn menu.
. Use 0 to scroll to Learn menu.
. Press ü to enter the user set-up menu.
. Enter operator code.
Installer menu to allow cards to be learned.
. The installer must have the learn facility enabled in the
5. Learning cards onto controller.
. Use X to exit from the menu.
. The controller will display Accepted , the new pin is set.
. Use keys 0-9 to verify pin.
. Use keys 0-9 to enter new pin.
. Press ü to enter change pin menu.
. Use 0 to scroll to Change Pin menu.
. Enter operator code.
4. Changing Operator code.
Factory default code: ( Operator: 123456 ).
. Use X to exit from the menu.
. New time will be displayed. Press ü to Accept.
. Repeat for month, day , hour and minute.
. Use numeric keys 0-9 to Enter the year . Press ü
. Press ü to select.
. Use 0 to scroll to “Set Date/Time”
. Enter the operator code
3. Setting Time and Date
. Use X to exit from the menu.
. Use keys 0-9 to enter the last card. Press ü.
. Use keys 0-9 to enter the first card. Press ü.
For a range of cards:
. Press ü to disable the card.
. Use 0 to scroll to the desired card.
For a single card:
. Press 0, then ü to enter the enable menu.
. Press ü to enter the user set-up menu.
. Enter the operator code.
2. Disabling cards
. Use X to exit from the menu.
. Use keys 0-9 to enter the last card. Press ü.
. Use keys 0-9 to enter the first card. Press ü.
For a range of cards:
. Press ü to enable the card.
. Use 0 to scroll to the desired card.
For a single card:
. Press ü to enter the enable menu.
. Press ü to enter the user set-up menu.
. Enter the operator code.
1. Enabling cards
(for typical Standalone System)
QUICK PROGRAMMING GUIDE
Good Housekeeping.
Access Control Technology thank you for choosing its product.
Please find below some useful notes to ensure satisfactory
performance from your Access Control System.
• Ensure that any lost cards are immediately deleted from the
system.
• Ensure that any damaged user cards are replaced , by your
Installer.
• Ensure that your staff are fully aware of the operation of readers
and report any system problems to the Installer immediately .
IMPORTANT
As with any access control system, always ensure that there is an
alternate means of escape in the event of the unit failing to operate due to power loss or in the event of fire.
Unit 8, Tallaght Business Centre,
Whitestown, Dublin 24, Ireland.
Tel: 353-1-4622585 Fax: 353-1-4622587
Copyright 2002 Access Control Technology Ltd.
(18-00007-00)
ACT1000/2000 Access Control Unit
(Operator Instructions)
www.accesscontrol.ie
System Log
Group Setup
User Setup
0
Operator Menu
Operator Menu
(This is the default code)
1
2 3 4 5 6
8
0
moves to the next character.
moves to the previous character.
If pressed on the first character,
then the option "Clear ?" is given.
pressed.
3
to select which door to control.
accepts the entered text.
Aux Output Off
Aux Output On
Pass Door
*On the ACT2000 you will first be prompted
Entering Text
Several menus allow text names to
be entered for users or groups.
When editing text, the numeric keys 1
to 9 are used to enter the required
characters. Each cycles through a
sequence of characters or digits when
0
Normalise Door
Unlock Door
Control Door*
Lock Door
Change PIN
Issue Number
Set Holidays
User Tracking
Set Date/Time
Time Zones
Control Door
7
0
Assign Options
1
6
7
8
9
w x y z W X Y Z 8
(SPC) - & . + ' / 9 0
p q r P Q R 6
s t u v S T U V 7
4
5
m n o M N O 5
j k l J K L 4
2
3
d e f D E F 2
g h i G H I 3
a b c A B C 1
7
Filter Log
Print Log
Display Log
System Log
Assign PINs
7
7
3
0
Assign Options
Access Rights
Assign Names
Group Setup
Disable
Enable
Card Validity
Batch Cards
One-To-One
Learn
7
Assign Groups
Assign PINs
0
Assign Names
User Setup
Disable
Enable
Changing PIN codes
4
Enter new PIN
5 6
7
Several menus require a PIN code to be entered or
changed, such as the "Change PIN" function in the
Operator menu, or the "Assign PINs" functions in
the User and/or User Setup menus.
Enabled
User 27
7
this case the prompt "Goto" is displayed.
The X key will exit from the current function and
return to the previous menu.
To User 27_
3
User 2
"To User" are displayed.
On other menus, the numeric keys may be used to
jump quickly to a particular user or group number. In
Not Allowed
Verify PIN
Accepted
Verify PIN
4
Verify PIN
5 6
or
7
The controller initially prompts for the new PIN to be
entered. The display indicates how many digits are
required, usually 4 or 6.
When the new PIN is entered, the controller prompts
for the code to be verified to ensure that no mistakes
have been made. Assuming all is OK, the controller
will display "Accepted" - the new PIN is now set.
User and Group PINs may be unset (removed) by
entering a PIN consisting of all zeros.
From User 5_
Enabled
3
2
7
to use the numeric keys to directly enter a
range of users on which the desired changes
will be made. The prompts "From User" and
1
User 2
changed (for example, editing the name).
As a short cut, on some menus it is possible
User 2
Pressing the accept key will change the state
for the currently displayed user or group, or
will allow the displayed information to be
Disabled
3
User 2
The lower line will show the current setting for
the item that is being configured.
Pressing the zero key will advance to the next
user or group.
Disabled
0
the number of the group or user. If a text name
has been entered, this will be shown instead.
Menu navigation in User & Group Setup functions
User 1
When one of the user or group setup functions
is invoked, the top line of the display will show
Loading...