Page 1
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
T300
THERMAL BINDER
220-240V
ILLUSTRATED PARTS LISTS
AND
SERVICE INSTRUCTIONS
Compiledby IssueNo2
Approved by (Technical Manager) Date
REXEL BUSINESS MACHINES, DROITWICH, WORCESTERSHIRE, WR9 9AP, ENGLAND
TELEPHONE +44 (0) 1905 771555 FAX +44 (0) 1905 823374
T300.doc 1
Issue No 1
Page 2
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
TABLE OF CONTENTS
ILLUSTRATED PARTS MANUAL
T300 THERMAL BINDER
220-240V
Contents Page2
Preface Page 3
Illustrated parts list - Mouldings Pages 4 – 5
Mechanism and Electrics Pages 6 – 8
Service Instructions - To serial No A545817 Pages 9 – 14
Section 1.0 Replacement of Top Cover Page 9
Section 2.0 Replace lid moulding Page 10
Section 2.1 Replacement of Heater Assembly Page 10
Section 2.2 Replacement of Fixing Blocks Page 11
Section 2.3 Replacement of Insulation Page 11
Section 2.4 Replacement of base moulding Page 11
Section 3.0 Replacement of PCB Page 12
Section 4.0 Replacement of document support bar/
Spring/Lever arm Page 12
Section 4.1 Replacement of buttons Page 12
Section 4.2 Replacement of Thermistor Page 13
Section 5.0 Wiring Diagram 220/240
To Serial No A545817 Page 14
Service Instructions - From Serial No A545818
Section 6.0 Replacement of Top Cover Page 15
Section 7.0 Replace lid moulding Page 16
Section 7.1 Replacement of Heater Assembly Page 16
Section 7.2 Replacement of Fixing Blocks Page 17
Section 7.3 Replacement of Insulation Page 17
Section 7.4 Replacement of base moulding Page 17
Section 8.0 Replacement of PCB Page 17
Section 9.0 Replacement of document support bar/
Spring/Lever arm Page 18
Section 9.1 Replacement of buttons Page 18
Section 10.0 Wiring Diagram 220/240
From Serial No A545818 Page 19
Section 11 Specifications Page 20
Amendment Record Sheet Page 21
T300.doc 2
Issue No 1
Page 3
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
PREFACE
SERVICE PREPARATION
This manual provides the instructions for the replacement of all the components that may become worn or
damaged. Details of replacement parts and ordering information are given in associated illustrated parts list.
Illustrated Parts Lists For each machine give full details of the replacement part numbers with
supporting diagrams to show the location of the components.
Service Instructions For each machine give the recommended servicing procedure with supporting
pictorial diagrams for added clarity.
WARNING
1. Check the machine RATING PLATE DETAILS are compatible with the electrical mains supply.
2. Disconnect the electrical mains supply before removing any covers.
3. Upto serial number A545817, all machines must have a sound electrical earth connection.
From serial number A545818 all machines are double insulated and do not require an earth
connection.
T300.doc 3
Issue No 1
Page 4
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
MOULDINGS
No Description Part Qty Comment
1 Service Call Decal D000185 1 Not shown
2 Bottom Moulding D52501 1
3 On Button – Grey D52507 1
4 Off Button – Red D52508 1
5 Programme Select Button – Yellow D52509 1
6 Bind Button – Green D52510 1
7 Lid Pad Print D52516 1
8 Top Cover Pad Print D52517 1
9 No 4 x ½” Pan Plasfast Screw SCR716 6
10 Self Adhesive Rubber Feet SL18-294 4
11 Document Feet D52519 1
12 Spring Arm D52512 1 Not shown
13 Coil Spring D52518 1 Not shown
T300.doc 4
Issue No 1
Page 5
MOULDINGS
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
T300.doc 5
Issue No 1
Page 6
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
MECHANISM & ELECTRICS
NoDescription Part Qty Comments
1 Heater Assembly 230V 600W A52505 1 To Serial No A545817
Heater Assembly 230V 600W A52527 1 From Serial No A545818
2 Heater Extrusion D52503 1 To Serial No A545817
Heater Extrusion From Serial No A545818 Inc in
A52527
3 Heater Fixing Block D52504 2
4
5
6 Compression Spring (clip) D52511 3 To Serial No A545817
7 Thermal Fuse Holder (Clip) D52513
Thermal Fuse Holder (Clip) 4 From Serial No A545818 Inc in
A52527
8 Base Insulation D52514 1
9 Nut Brass M3 Full NM32 2 To Serial No A545817
10 M3 Plain Brass Washer PLN34 1 To Serial No A545817
11 M3 x 12mm C’sunk slot head
SCM145 1 To Serial No A545817
brass
12 M3 x 8 Pozi Pan Rec’d
SCR713 12
Plasform
13 M3 Plain Brass Washer SHK12 1 To Serial No A545817
14 T300 Thermal Binder PCB
SL17-262 To Serial No A545817
230V
T300 Thermal Binder PCB
SL17-299 1 From Serial No A545818
230V
15 Laminator Cordset UK SL4-102 1 To Serial No A545817
Laminator Cordset (Euro) SL4-103 1 To Serial No A545817
Laminator Cordset (Aust) SL4-104 1 To Serial No A545817
Laminator Cordset (Export) SL4-106 1 To Serial No A545817
Laminator Cordset (UK) SL4-199 1 From Serial No A545818
Laminator Cordset (Euro) SL4-120 1 From Serial No A545818
Laminator Cordset (SA) SL4-120 1 From Serial No A545818 fitted
with SL12-43 plug
16 Thermistor Assembly SL17-268 1 To Serial No A545817
Thermistor Assembly 1 From Serial No A545818 inc in
A52527
17 Crimp Terminal Housings SL13-66 2
18 No 4 x ¼” Self Tapper SCR541 1 To serial No A545817
19 M3 Fibre Washer FIB 1 4
T300.doc 6
Issue No 1
Page 7
To Serial No A545817
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
MECHANSIM & ELECTRICS
T300.doc 7
Issue No 1
Page 8
From Serial No A545818
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
MECHANSIM & ELECTRICS
T300.doc 8
Issue No 1
Page 9
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SERVICE INSTRUCTIONS
This manual provides instructions for the replacement of components that may become worn or damaged.
WARNING
Check rating plate details are compatible with electric supply. Disconnect mains supply before removing
cover.
SECTION 1.0 (To serial no A545817)
Replacement of Top Cover
1. Ensure that mains cable is disconnected from the supply.
2. Remove the two rubber feet that are on the left hand and right hand side, towards the front of the
machine.
3. Remove the six fixing screws using a pozi drive screwdriver.
4. Lift base of machine away from top cover and place on a nearby flat surface.
5. The top cover should now remain face down.
6. Remove the four screws securing the PCB.
7. Remove the PCB, by unclipping the three crimp housings on the thermistor, mains connection and
the heater.
8. Remove the four buttons.
9. Ensure document support bar is in down position on top cover.
10. Remove the spring that fixes the document support bar to the lever arm, by unhooking it from the
screw boss, on the rear right hand side of the machine and place on one side.
11. Unhook the lever arm by pulling the lever upwards, towards, the inside of the cover; slide it over the
end of the bar and place on one side.
12. Turn the top cover over, so that the document support bar is facing you.
13. Lift the document support bar upwards and squeeze the extended legs on the bar together.
14. Release bar and remove from top cover.
15. Replace top cover.
16. To reassemble machine reverse order of operations 1 – 12.
T300.doc 9
Issue No 1
Page 10
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 2.0 (To serial no A545817)
Replace Lid Moulding
1. Remove lid from top cover, by bowing inwards to release hinge pins.
2. Replace lid.
3. Check that pivot pins are correctly aligned in top cover.
4. Check lid opens and closes correctly.
SECTION 2.1
a. Replacement of Heater Assembly
1. Carry out procedures 1 to 4 in section 1.0.
2. The heater assembly is secured to 2 off heater fixing blocks by four fixing screws.
3. Remove the four fixing screws.
4. Unclip heater wire and thermistor connectors from PCB assembly.
5. Lift and remove heater assembly complete.
6. To reassemble machine, reverse sequence of operation 1 to 5.
b. Replacement of Heater Assembly (Including Thermistor)
1. Carry out procedures 1 to 4 in section 1.0.
2. The heater assembly is secured to 2 off heater fixing blocks by four fixing screws.
3. Remove the four fixing screws.
4. Unclip heater wire thermistor and mains connector from PCB assembly.
5. Lift and remove heater assembly complete.
6. To reassemble machine, reverse sequence of operation 1 to 5.
T300.doc 10
Issue No 1
Page 11
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 2.2
Replacement of Fixing Blocks
1. Carry out procedures 1 to 4 section 2.1
2. Turn base moulding upside down.
3. Remove service decal and rating plate.
4. Unscrew four fixing screws
5. Blocks can now be replaced
6. Reassemble machine in reverse sequence of operations 1 to 4.
SECTION 2.3
Replacement of insulation
1. Carry out procedures 1 to 4 section 2.1
2. Insulation is secured using double sided sticky tape.
3. Ease free sticky tape from insulation.
4. Remove and replace insulation.
5. Reassemble machine in reverse sequence of operations 1 to 3.
SECTION 2.4
Replacement of Base Moulding
1. Carry out procedures 1 to 5 section 2.1
2. The extrusion/heater assembly will now become free.
3. Place on one side.
4. Remove insulation as procedures 2 to 4 section 2.3
5. Replace base moulding.
6. Reassemble machine in reverse sequence of operations 1 to 4.
T300.doc 11
Issue No 1
Page 12
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 3.0
Replacement of PCB
1. Carry out procedures 1 to 7 section 1.
2. Replace the PCB
3. Reassemble machine In reverse sequence.
SECTION 4.0
Replacement of document support bar/spring/lever arm
1. Carry out procedures 1 to 4 section 1.
2. To remove extension spring unhook from rear screw boss and lever arm.
3. Replace spring.
4. To remove lever arm carry out procedures 1 to 4 section 1, and then 9 to 11 section 1.
5. To remove document support bar, carry out procedures 1 to 5 section 1.0 and procedures 9 to 14 in
section 1.0.
6. Replace document support bar.
7. Reassemble machine by reversing above operations.
SECTION 4.1
Replacement of Buttons
1. Carry out procedures 1 to 8 section 1.0.
2. Replace the buttons, making sure that the grey button is in the aperture marked 1, the red button is In
the aperture marked 0, the yellow button is in the aperture marked ? and the green button in the
aperture marked
3. Reverse procedure 1 to reassemble machine.
SECTION 4.2
T300.doc 12
Issue No 1
Page 13
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
Replacement of Thermistor
1. Carry out procedures 1 to 4 section 2.1
2. Remove thermistor for connection on PCB.
3. The PCB may be removed to ease replacement. If required refer to section 1 produce 6.
4. Replace thermistor
5. Reverse assembly of operations 3 to 1 if PCB was removed, otherwise 2 to 1.
T300.doc 13
Issue No 1
Page 14
Section 5.0
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
WIRING DIAGRAM 220/240V WD317 TO SERIAL NO A545817
T300.doc 14
Issue No 1
Page 15
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SERVICE INSTRUCTIONS
This manual provides instructions for the replacement of components that may become worn or damaged.
WARNING
Check rating plate details are compatible with electric supply. Disconnect mains supply before removing
cover.
SECTION 6.0 (From serial no A545818)
Replacement of Top Cover
17. Ensure that mains cable is disconnected from the supply.
18. Remove the two rubber feet that are on the left hand and right hand side, towards the front of the
machine.
19. Remove the six fixing screws using a pozi drive screwdriver.
20. Lift base of machine away from top cover and place on a nearby flat surface.
21. The top cover should now remain face down.
22. Remove the four screws securing the PCB.
23. Remove the PCB, by unclipping the three crimp housings on the thermistor, mains connection and
the heater.
24. Remove the four buttons.
25. Ensure document support bar is in down position on top cover.
26. Remove the spring that fixes the document support bar to the lever arm, by unhooking it from the
screw boss, on the rear right hand side of the machine and place on one side.
27. Unhook the lever arm by pulling the lever upwards, towards, the inside of the cover; slide it over the
end of the bar and place on one side.
28. Turn the top cover over, so that the document support bar is facing you.
29. Lift the document support bar upwards and squeeze the extended legs on the bar together.
30. Release bar and remove from top cover.
31. Replace top cover.
32. To reassemble machine reverse order of operations 1 – 12.
T300.doc 15
Issue No 1
Page 16
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 7.0 (From serial no A545818)
Replace Lid Moulding
5. Remove lid from top cover, by bowing inwards to release hinge pins.
6. Replace lid.
7. Check that pivot pins are correctly aligned in top cover.
8. Check lid opens and closes correctly.
SECTION 7.1
a. Replacement of Heater Assembly (including Thermistor)
1. Carry out procedures 1 to 4 in section 6.0.
2. The heater assembly is secured to 2 off heater fixing blocks by four fixing screws.
3. Remove the four fixing screws.
4. Unclip heater wire/thermistor and mains connectors from PCB assembly.
5. Lift and remove heater assembly complete.
6. To reassemble machine, reverse sequence of operation 1 to 5.
SECTION 7.2
Replacement of Fixing Blocks
7. Carry out procedures 1 to 4 section 7.1
8. Turn base moulding upside down.
9. Remove service decal and rating plate.
10. Unscrew four fixing screws
11. Blocks can now be replaced
12. Reassemble machine in reverse sequence of operations 1 to 4.
T300.doc 16
Issue No 1
Page 17
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 7.3
Replacement of insulation
6. Carry out procedures 1 to 4 section 7.1
7. Insulation is secured using double sided sticky tape.
8. Ease free sticky tape from insulation.
9. Remove and replace insulation.
10. Reassemble machine in reverse sequence of operations 1 to 3.
SECTION 7.4
Replacement of Base Moulding
7. Carry out procedures 1 to 5 section 7.1
8. The extrusion/heater assembly will now become free.
9. Place on one side.
10. Remove insulation as procedures 2 to 4 section 7.3
11. Replace base moulding.
12. Reassemble machine in reverse sequence of operations 1 to 4.
SECTION 8.0
Replacement of PCB
4. Carry out procedures 1 to 7 section 6.
5. Replace the PCB
6. Reassemble machine In reverse sequence.
T300.doc 17
Issue No 1
Page 18
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
SECTION 9.0
Replacement of document support bar/spring/lever arm
8. Carry out procedures 1 to 4 section 6.
9. To remove extension spring unhook from rear screw boss and lever arm.
10. Replace spring.
11. To remove lever arm carry out procedures 1 to 4 section 6, and then 9 to 11 section 6.
12. To remove document support bar, carry out procedures 1 to 5 section 6.0 and procedures 9 to 14 in
section 6.0.
13. Replace document support bar.
14. Reassemble machine by reversing above operations.
SECTION 9.1
Replacement of Buttons
4. Carry out procedures 1 to 8 section 6.0.
5. Replace the buttons, making sure that the grey button is in the aperture marked 1, the red button is In
the aperture marked 0, the yellow button is in the aperture marked ? and the green button in the
aperture marked
6. Reverse procedure 1 to reassemble machine.
T300.doc 18
Issue No 1
Page 19
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
WIRING DIAGRAM 220/240V WD404 (From Serial No A545818)
T300.doc 19
Issue No 1
Page 20
SECTION 11.0
SPECIFICATION SHEET
T300
POWER SUPPLY 220/240V 50Hz
HEIGHT 95 mm
WIDTH 370 mm
DEPTH 220 mm
WEIGHT 2 Kgs
MACHINE POWER 600W
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
DOCUMENT SIZE MAX A4
T300.doc 20
Issue No 1
Page 21
ILLUSTRATED PARTS MANUALS
T300 THERMAL BINDER
220-240V
AMENDMENT RECORD SHEET
ISSUE
DECRIPTION
NO
1 Original 2 Instructions altered to include double insulated product. 187
CARO No
T300.doc 21
Issue No 1
Loading...