Acclaim Lighting AL Dimmer 1 HP User Manual
AL-DIMMER-1 HP
User Instructions
DESCRIPTIONS
Congratulations with your purchase of this product.
Read this manual carefully before using our AL-DIMMER-1 HP. This unit serves as a single channel dimmer. It is
designed to set the intensity for the high power R.G.B. LEDs, features the user may select the current output as
350mA, 500mA or 700mA. Its working mode is available in DMX control and Manual Dim mode, and the analog
signal is available in 0~10V and 1~10V, it's working mode and the DMX address can be set by Dip-switch.
DELIVERY PACKET
Check for transport damage.
You should be in possession of the following items:
1 AL-DIMMER-1 HP
1 Manual
1 Screwdriver
GND
Data-
Data+
GND
Data -
Data+
+12-24V
+12-24V
GND
GND
Should you discover transport damage after unpacking the equipment,
inform the hauler immediately. Never connect a damaged device. You
may also contact your supplier.
TECHNICAL SPECIFICATIONS
Power Requirement
Output Current 350mA,500mA or 700mA for option
DC In
DMX In/Out
Analog In/THRU
Loading Output
Housing
Control Protocol
Connection
Listing
Operation temperature
Ingress Protection Rating
Dimensions
Weight
12~24VDC
4-pin terminal
3-pin terminal
2-pin terminal
2-pin terminal
Black plastic
DMX-512 (1990)
Terminal
CE certified
0 degC to +40 degC
IP 20
115(L) x 54(W) x 23(H)mm
150g
DMX IN
DMX Address Setting
3
4
1 2
1
2
4
8
Addr
DMX OUT
1
2
4
8
Dim
350mA
DC IN
AL-DIMMER-1 HP
5
678 9 10
11 12
32
64
16
256
128
DMXMAN
32
64
16
128
500mA 700mA
AL-DIMMER-1 HP
1-10V0-10V
CURVE
OUTPUT
Made in P.R.C.
0-10V/1-10V
0-10V/1-10V
THRU IN
RoHS
GND
GND
OPERATION GUIDE
1.Output Current Option
Make sure the output current matches the power requirements of the LED fixtures prior to use AL-DIMMER-1 HP.
The output current defaults as 350mA and a built-in Dipswitch allows the user to select the output current
as 350mA,500mA or 700mA.
The following contents instruct to how to make the selection for the output current.
-1-
1. Take out the AL-DIMMER-1 HP and the screw driver from packing.
2. Use the screw driver to prize up the rear panel of AL-DIMMER-1 HP with the proper strength, as the following
figures.
3. Use the screw driver to move the 2 way dip-switch to on or off for output current option.
2 way dip-switch
ON
1 2
OFF
Current
350mA
500mA
500mA
700mA
2
Off
1
Off
Off On
On Off
On On
While both the built-in Dipswitch are "Off", the AL-DIMMER-1 HP will output 350mA current, both the current
indicators on . the front panel will black out
While the one of the built-in Dipswitch is "On", the AL-DIMMER-1 HP 500mA current, the one of the current
will output
indicator on the front panel will light, the other black out.
While both the built-in Dipswitch are "On", the AL-DIMMER-1 HP will output current, both the current
indicators on .
the front panel will light
700mA
4. After the current was selected, to reassemble the rear panel.
After the reassembly is completed, to connect the AL-DIMMER-1 HP to the power source for use.
Reassembly
-2-
Loading...