Abocom UTM560 User Manual

Page 1
USB V.90 TINY MODEM
Quick Installation Guide
Page 2
FCC REGULATORY STATEMENTS
FCC Part 68 Registration
This high speed USB 56K FAX/MODEM complies with FCC Part 68 rules, and the use of this modem is subject to the following restrictions:
1. The FCC has established rules which permit this device to be directly connected to the telephone network. Standardized jacks are used for these connections. This equipment should not be used on party lines or coin phones.
2. If this device is malfunctioning, it may also be causing harm to the telephone network; this device should be disconnected until the source of the problem can be determined and until repair has been made. If this is not done, the telephone company may temporarily disconnect service.
3. The telephone company may make changes in it's facilities, equipment, operation and procedures; if such changes affect the compatibility or use of this device, the telephone company is required to give adequate notice of the situation with the FCC.
4. If the telephone company requests information on what equipment is connected to their lines, inform them of:
a. The telephone number to which this unit is connected. b. The Ringer Equivalence Number (REN). c. The USOC jack required.
d. The FCC Registration number. Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the REN's of all the devices on any one line should not exceed 5.0. If too many devices are attached, they may not ring properly.
FCC Part 15 Registration
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interface, and
2) This device must accept any interface received, including interface that may cause undesired operation.
Page 3
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
(1) Reorient or relocate the receiving antenna.
(a) Increase the distance between the equipment and
receiver
(b) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(2) Consult an experienced radio/TV technician for help.
CTR 21 pan-European Certification
This equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
This device is designed to work with the notified networks in all EC member states. Nevertheless, some of the network services in invidual countries might not be supported, but they will not affect the normal data and fax applications. For example, the metering charge service in Germany. Besides you may encounter difficulty of using PULSE dialing function in some of the countries, such as Nordic countries. This kind of network compatibility is dependent on the physical and software settings of this device. If the users are desired to use this device on those networks, they should contact the vendor or supplier first.
Page 4
Table of Contents
Introduction .............................................................1
PECIFICATIONS
S
.....................................................1
Modem ...............................................................1
Fax.....................................................................1
YSTEM REQUIREMENTS
S
........................................2
Hardware Installation .............................................3
Software Installation ...............................................4
NSTALLATION FOR WINDOWS
I
98...........................4
Setup Diagnostics ..............................................6
NSTALLATION FOR WINDOWS
I
2000.......................7
Setup Diagnostics ..............................................9
NSTALLATION FOR WINDOWS MILLENNIUM
I
........10
Setup Diagnostics ............................................13
Internet Access.......................................................14
Page 5

Introduction

The USB V.90 Tiny Modem complies with the Universal Serial Bus functionality built in Windows 98/2000/Millennium. It is compatible with Bell, ITU-T (formerly CCITT) and Hayes AT commands. The USB V.90 Tiny Modem enables you enjoy all the benefit offered by USB technology and get a faster and easier Internet access.
With the especially compact design of the Tiny Modem, you can not only save the cost but also eliminate the need of using an extra USB cable as you usually do. Moreover, using standard phone lines, the data communication functions of the modem will enable you to successfully hook up to the Internet, transmit E-mail, send and receive information and communicate with other PCs, Bulletin Board Services (BBS) or computer networks such as CompuServe.

Specifications

Modem

V.90, K56flex 56Kbps, V.34+ 33.6Kbps, V.34
28.8Kbps, V.32bis 14.4Kbps
V.42bis/V.42, MNP 2-5 data compression and
error correction
AT command set
Fax
G3, V.17 14400bps, V.29 9600bps, Fax Service Class 1 compliant
- 1 -
Page 6

System Requirements

A Pentium
processor-based personal computer
166MMX or above
At least 16 MB of RAM An USB port Microsoft Windows 98/2000/Millennium A CD-ROM drive
- 2 -
Page 7

Hardware Installation

1. Locate the USB host port of your system. Connects the USB Type A connector to the USB host port on your computer.
2. Connects the phone line to the phone line jack
- 3 -
Page 8

Software Installation

Installation for Windows 98

1. When the USB V.90 Tiny Modem is well
connected to your computer, Windows 98 will automatically detect the new device. Click Next.
2. Select Search for a suitable driver for my
device (recommended) and click Next.
3. Insert the device driver compact disc into the
CD-ROM drive and select Specify a location. Click Browse button and select the drive where
- 4 -
Page 9
you load the device driver. Click Next. Windows will start searching for the appropriate driver for the software installation.
4. Click Next.
5. Click Finish. The software installation is
successfully completed.
6. When the following dialog box appears, select
the country/location where you are, and click Enable PBX. Click OK.
7. When finished, restart your computer to activate
the new device.
- 5 -
Page 10

Setup Diagnostics

You can perform the following steps to check if your USB V.90 Tiny Modem is well installed.
1. Go to
StartSettingsControl PanelModems.
2. When the Modems Properties dialog box
appears, select the Diagnostics tab.
3. Select USB V.90 TINY MODEM and click OK.
4. If USB V.90 TINY MODEM is not found, stop
the diagnostics procedures and skip to the following section titled Uninstallation.
5. The USB modem is well installed if the
information is found on the following screen. Click OK to exit.
- 6 -
Page 11

Installation for Windows 2000

1. Once the USB V.90 Tiny Modem is well connected to your computer, Windows 2000 will automatically detect the new device. Click Next.
2. Select Search for a suitable driver for my device (recommended) and click Next.
3. Insert the device driver compact disc into the CD-ROM drive. Select Specify a location and click Next.
- 7 - - 8 -
Page 12
4. Click Browse button and select the drive where you load the device driver (for example: G:\WIN2K). Click OK. Windows will start searching for the appropriate driver for the software installation.
5. Click Next to continue.
6. Click Yes.
7. Click Finish.
8. When Windows prompt you “Modem Country Selection”, choose the country where you locate. Select the Enable PBX check box and click OK. The software installation is then complete.
9. The software installation is successfully complete.
Page 13

Setup Diagnostics

To verify whether your USB V.90 Tiny Modem exists in your computer and is enabled, go to My
ComputerControl PanelSystem. Click the Device Manager tab. If the USB V.90 TINY MODEM and Network adapters are found, it
means that your Network device is well installed. If not, consult your computer dealer for technical support.
- 9 -
Page 14

Installation for Windows Millennium

1. When the USB V.90 Tiny Modem is well
connected to your computer, Windows ME will automatically detect the new device. Select Specify the location of the driver (Advanced) and click Next.
2. Load the device driver compact disc into the
CD-ROM of your system and select Specify a location. Click the Browse button to select the drive where you load the device driver (for example: D:\WinME). Click Next.
- 10 -
Page 15
3. Expect a minor delay for Windows to search for
the appropriate driver for the device. Click Next.
4. Click Finish. The installation program will
continue.
5. Select Specify the location of the driver
(Advanced) and click Next.
6. When the above figure appears, repeat step 2,
namely, select Specify a location. Click the Browse button to select the drive where you load the device driver (for example: D:\WinME). Click Next.
- 11 -
Page 16
7. Click Next.
8. When Windows prompt you “Modem Country
Selection”, choose the country where you locate. Select the Enable PBX check box and click OK.
9. Click Finish to complete the installation.
- 12 -
Page 17

Setup Diagnostics

1. To verify if the USB V.90 Tiny Modem is well
installed and enabled, you can perform the following steps.
2. Go to
StartSettingsControl PanelModems.
3. When the Modems Properties dialog box
appears, select the Diagnostics tab.
4. Highlight USB V.90 TINY MODEM and click
the More Info… button.
5. If the following information can be found, it
means that the USB modem is well installed and enabled. Click OK to exit.
- 13 -
Page 18

Internet Access

1. Go to My Computer.
2. Select Dial-Up Networking.
3. Double-click Make a New Connection, a
dialogue box will appear for you to name the new connection and select the device. Name the new connection appropriately and click Next.
4. Enter the area code and phone number of your
Internet Service Provider (ISP). Follow the on­screen instructions to proceed.
5. When finished, from the Dial-Up Networking
window, right-click your newly created connection. Select Properties. On the Server Types tab, enter the proper selections as shown below and click OK to finish the settings.
6. For Windows Millennium, the figure above
should be displayed as follows.
- 14 - - 15 -
Page 19
7. Now, you are ready to connect to the Internet.
Loading...