Abit SI-1NS42, SI-1NS40, SI-1NS60 User Manual
SI-1Ns40/
SI-1Ns42/SI-1Ns60
Intel Pentium 4 Server Board
Socket 478
User’s Manual
Rev. 2.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
SI-1Ns40/SI-1Ns42/SI-1Ns60
Table Of Contents
Chapter 1. Introduction .................................................... 1-1
1.1. Features & Specifications....................................................... 1-1
1.2. Layout..................................................................................... 1-3
1.3. Jumpers & Connectors Description........................................ 1-4
Chapter 2. Hardware Setup.............................................. 2-1
2.1. CPU Socket ............................................................................2-1
2.2. System Memory .....................................................................2-2
2.3. Power Connectors................................................................... 2-3
2.4. FAN Connectors..................................................................... 2-4
2.5. CMOS Memory Clearing Header ..........................................2-5
2.6. Front Panel Switches & Indicators Connection Headers ....... 2-6
2.7. External Keyboard/Mouse Connection Header ..................... 2-7
2.8. System Management Bus Connection Header....................... 2-8
2.9. IDE Disk Drive Connector..................................................... 2-9
2.10. PCI Expansion Slot ..............................................................2-10
2.11. Additional COM Port Connection Header........................... 2-11
2.12. Additional USB Port Connection Header ............................2-12
2.13. VGA Output Connection Header ......................................... 2-13
2.14. Compact Flash Memory Card Reader Socket...................... 2-14
2.15. Status Indicators ...................................................................2-15
2.16. Power-On Switch .................................................................2-16
2.17. System-fail LED Connection Header................................... 2-17
2.18. Parallel Port Header.............................................................. 2-18
2.19. External I/O Panel Connectors............................................. 2-19
User’s Manual
Chapter 3. BIOS Setup...................................................... 3-1
3.1. Standard CMOS Features....................................................... 3-2
3.2. Advanced BIOS Features ....................................................... 3-5
3.3. Advanced Chipset Features.................................................... 3-8
3.4. Integrated Peripherals........................................................... 3-10
3.5. Power Management Setup.................................................... 3-15
3.6. PnP/PCI Configurations .......................................................3-17
3.7. PC Health Menu ................................................................... 3-19
3.8. Load Fail-Safe Defaults........................................................ 3-21
3.9. Load Optimized Defaults .....................................................3-21
3.10. Set Password......................................................................... 3-21
3.11. Save & Exit Setup ................................................................3-21
3.12. Exit Without Saving ............................................................. 3-21
Chapter 4. Driver Installation .......................................... 4-1
4.1. Setup Items ............................................................................. 4-2
Appendix A. How to Get Technical Support ..................... A-1
SI-1Ns40/SI-1Ns42/SI-1Ns60
Introduction 1-1
Chapter 1. Introduction
1.1. Features & Specifications
CPU
• Supports Intel Pentium 4 socket 478 processor up to 3.06GHz and later
(based on 400/533MHz FSB)
Chipset
• Intel RG82845GV (845GV) / FW82801DB (ICH4)
Networking Security
• Onboard Cavium CN-1005 Security Micro Processor support
IPsec/SSL acceleration
Memory
• Two 184-pin DIMM sockets supporting 64-bit wide Single Channel
DDR 200/266/333 memory
• Up to 2GB, un-buffered and non-ECC memory capacity
LAN
• SI-1Ns40: 4x Intel 82551ER single port 10/100 Ethernet
• SI-1Ns42: 2x Intel 82541ER single port GbE Ethernet
4x Intel 82551ER single port 10/100 Ethernet
• SI-1Ns60: 6x Intel 82551ER single port 10/100 Ethernet
VGA
• Integrated graphics controller by Intel RG82845GV
PCI Expansion Slot
• 1x PCI 32bit/33MHz expansion slot (3.3V)
Internal I/O Headers
• 1x 44-pin Ultra DMA 100/66/33 connector
• 1x 50-pin IDE Interface Compact Flash Type II Socket
• 1x VGA header
• 1x LPT header
• 1x PS/2 Keyboard/Mouse header
• 1x COM header (COM1)
• 1x USB 2.0 header (Supports two USB 2.0 connectors)
User’s Manual
1-2 Chapter 1
• 1x SM Bus header (For SM Bus and I
2
C)
External I/O Connectors
• 1x COM port (COM2)
• 2x USB 2.0 connectors
• 4x RJ-45 w/Transformer LAN connectors (SI-1Ns40)
• 6x RJ-45 w/Transformer LAN connectors (SI-1Ns42, SI-1Ns60)
System BIOS
• Supports Plug-and-Play (PNP)
• Supports Advanced Configuration Power Interface (ACPI)
• Write-Protect Anti-Virus function by AWARD BIOS
• 4MB Flash ROM
Miscellaneous
• ATX form factor (305mm x 245mm)
• Hardware monitoring - including fan speeds, voltages, and system
environment temperature
• Chassis-intrusion detector header
Specifications and information contained herein are subject to change
without notice.
SI-1Ns40/SI-1Ns42/SI-1Ns60
Introduction 1-3
1.2. Layout
User’s Manual
1-4 Chapter 1
1.3. Jumpers & Connectors Description
Jumpers Description Default Setting
CCMOS1 CMOS Clearing Header Pins 1-2 Close (Normal)
Connectors Description
ATXPWR1/ATX12V1 ATX12V Power Connectors
CF1 Compact Flash Memory Card Reader Socket
COM1 Additional COM Port Connection Header
COM2 COM Port Connector
DIMM1/DIMM2 DDR DIMM Slots
FAN1/FAN2/FAN3 Fan Power Connector with Speed Monitoring Support
FAN4 Fan Power Connector without Speed Monitoring Support
FPIO1 Front Panel Switches & Indicators Connection Headers
FP-USB1 Additional USB Port Connection Header
IDE1 IDE Disk Drive Connector
J1 System-fail LED Connection Header
KM1 External Keyboard/Mouse Connection Header
LAN1/LAN2
LAN3~LAN6 10/100Mbps LAN Connectors
PCI1 PCI Expansion Slot
SI-1Ns42: 10/100/1000Mbps LAN connectors.
SI-1Ns40, SI-1Ns60: 10/100Mbps LAN connectors.
PWR_ON
SMBUS1 System Management Bus Connection Header
USB1 External USB Port Connector
VGA1 VGA Output Connection Header
SI-1Ns40/SI-1Ns42/SI-1Ns60
External Power-On switch Connection
Header
Hardware Setup 2-1
Chapter 2. Hardware Setup
2.1. CPU Socket
This server board provides one 478-pin Zero Insertion Force (ZIF) socket to install the
Intel Pentium 4 CPU.
User’s Manual
2-2 Chapter 2
2.2. System Memory
This server board provides two 184-pin DDR DIMM slots for un-buffered and
non-ECC modules with memory size expansible up to 2GB (DDR333/266/DDR200).
DIMM DIMM Module Total Memory
1 256MB, 512MB, 1GB 256MB ~ 1GB
2 256MB, 512MB, 1GB 256MB ~ 1GB
Total System Memory 256MB ~ 2GB
SI-1Ns40/SI-1Ns42/SI-1Ns60
Hardware Setup 2-3
2.3. Power Connectors
These two connectors connect to ATX12V power supply.
User’s Manual
2-4 Chapter 2
2.4. FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your
system.
• FAN1/FAN2/FAN3: With speed monitoring support in BIOS menu
• FAN4: Without speed monitoring support in BIOS menu
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on
these connectors.
SI-1Ns40/SI-1Ns42/SI-1Ns60
Hardware Setup 2-5
2.5. CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
• Pin 1-2 shorted (default): Normal operation.
• Pin 2-3 shorted: Clear CMOS memory.
ATTENTION: Turn the system power off first (including the +5V standby power)
before clearing the CMOS memory.
User’s Manual
2-6 Chapter 2
2.6. Front Panel Switches & Indicators Connection
Headers
This header provides connection to external switches and indicators.
Pin Definition
1-2 S.LED
5-6 Reset
7-8 Chassis Intrusion
9-10 HD LED
SI-1Ns40/SI-1Ns42/SI-1Ns60
Hardware Setup 2-7
2.7. External Keyboard/Mouse Connection Header
This header provides the external connection to keyboard and mouse.
Pin Definition Pin Definition
1 VCC 2 VCC
3 NC 4 NC
5 KB Data 6 Mouse Data
7 Ground 8 Ground
9 KB Clock 10 Mouse Clock
User’s Manual
2-8 Chapter 2
2.8. System Management Bus Connection Header
This header provides the connection to system management bus (SMBus).
Pin Definition Pin Definition
1 SMBCLK 4 SMBDATA
3 Ground
5 VCC
SI-1Ns40/SI-1Ns42/SI-1Ns60
Hardware Setup 2-9
2.9. IDE Disk Drive Connector
This connector provides IDE hard drive connection (Pitch 2.5).
User’s Manual
Loading...