4IPNET EAP701 User Manual

EAP701 V1.00

Enterprise Access Point

Quick Installation Guide

EAP701 Enterprise Access Point ENGLISH

This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPN ET, INC. You may not alter or remo ve any copyright or other notice from copies of the conte nt. All o ther brand and p roduct names are claimed or registered marks of their respective companies or organizations.

To download up-to-date version, please visit www.4ipnet.com.

Quick Installation Guide

EAP701 Enterprise Access Point ENGLISH

FCC CAUTION

This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Quick Installation Guide

EAP701 Enterprise Access Point ENGLISH

CE CAUTION

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP701

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

• Radio: EN 300.328

• EMC: EN 301.489-1, EN 301.489-17,

• EMC: EN 55022

Class B, EN 55024:+ A1 + A2 including the followings: EN 61000-3-2, EN 61000- 3-3. EN 61000-4-2, EN 61000- 4-3, EN 61000-4-4, EN 61000-4-5, EN 61000- 4-6, EN 61000-4-11

• Safety: EN 60950-1 + A11,

Caution:

 This declaration is only valid for configurations (combinations of software, firmware, and hardware)

provided and supported by 4ipnet Inc. The use of software or firmware not provided and supp orted by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.

Taiwan NCC Statement

根據 NCC 低功率電波輻射性電機管理辦法規定:

第十二條

第十四條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時應立即停用，並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。

iii

Quick Installation Guide

EAP701 Enterprise Access Point ENGLISH

Preface Package Contents

The 4ipnet EAP701 Wall Jack Access Point is an in/on-the-wall as well as a ceiling-mounted Wi-Fi IEEE 802.1 1b/g/n 2.4GHz 2 X 2 MIMO access point, designed to blend into a working or a living environment practically and elegantly with its simplistic yet sleek design.

The compact EAP701 in a small form factor lays snug in a standard wall outlet box. Its side panel features LED status indicators and two RJ45 ports. It has the interfaces to serve both wireless and wired LAN access.

When coupled with the 4ipnet WHG series Controller, the EAP701 supports Tunnel-based AP Management, and comes with all standards demanded by enterprise applications, including business-grade security (802.1X, WPA and WPA2), and multiple ESSIDs with VLAN tags to separate

1. 4ipnet EAP701 x 1

2. Quick Installation Guide (QIG) x 1

3. Power Adapter (DC 5V) x 1 (Optional)

4. Mounting Screws x 2

5. Surface Mounting Panel x 1

6. Outlet Mounting Panel x 1

7. Mounting Plate Unfastening Tool x 1

It is recommended to keep the original

packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.

the traffics of different departments. A centralized WLAN management allows enterprises and organizations to support a wide array of value added applications, such as load balancing, bandwidth control, and access control. The patent-pending 4ipWES (Press-n-Connect) technology bridges multiple EAP701s at the touch of a button, which enables a quick and automatic WDS Easy Setup by pressing the WES button on EAP701. Extending wireless network coverage is a breeze, be it across conference rooms or along hallways.

EAP701’s high performance, security and optimal invisibility make it a perfect choice of wireless connectivity for your business.

Quick Installation Guide

System Overview

Lower Panel

EAP701 Enterprise Access Point ENGLISH

EAP701 Lower Panel

1 LAN 1 – 2 Ports 2

DC Jack 5V

Upper Panel

2 A

Attach Ethernet cables here to connect to the wired local network. Attach the power adaptor here.

EAP701 Upper Panel

1 Restart / Reset Button

Press once to restart the system; Press and hold for more than 5 seconds to reset to factory default.

2 LED Indicators 3 WES Button

4 LED lights. Representation is listed at the top of the panel. WDS Easy Setup. Press the button to build up a WDS link with another

peer.

+ 11 hidden pages

4IPNET EAP701 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual