4IPNET EAP210, OWL530 Users Manual

EAP210 or OWL530
Handbook
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Copyright Notice
This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.
All rights reserved.
To download up-to-date version, please visit www.4ipnet.com.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
FCC CAUTION
This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
The device contains a low power transmitter which will send out Radio Frequency (RF) signal when transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Copyright © 4IPNET, INC. All rights reserved.
ii
Quick Installation Guide
1. Installation personal
4ipnet OWL530 is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.
2. Installation location
4ipnet OWL530 shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved antenna(s)
EAP210 or OWL530 Enterprise Access Point ENGLISH
Professional installation instruction
may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of VZ9130002 limit and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty.
Copyright © 4IPNET, INC. All rights reserved.
iii
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: OWL530
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.
• Radio: EN 300.328:
• Radio: EN 50392
• EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings:
EN 61000-3-2, EN 61000-3-3. EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use
may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.
Taiwan NCC Statement
根據 NCC 低功率電波輻射性電機管理辦法 規定:
第十二條
第十四條
Copyright © 4IPNET, INC. All rights reserved.
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時應立即停用,並改善至
無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。
iv
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Preface Package Contents
4ipnet EAP210 or OWL530 is a high-end
802.1 1a/b/g/n 2.4GHz/ 5GHz MIMO Select able Dual Band Access Point (AP) designed to maximize deployment flexibility and feasibility for IT administrators.
The difference of EAP210 and OWL530 are the mounting method. EAP210 is a desktop device while OWL530 is designed to be pole-mount.
1. 4ipnet OWL530 x 1 or EAP210 x 1
2. Quick Installation Guide (QIG) x 1
3. CD-ROM
4. AC-DC Adaptor ( EAP210 only)
5. Power Sourcing Equipment (PSE) with AC cable x 1 (Optional)
6. Mounting Kit x 1 (OWL530 only)
7. Ground Cable x 1 (OWL530 only)
(with User’s Manual and QIG) x 1
Complying with the latest industrial wireless security standards that are required in the tightly secured enterprise network environments, the AP makes the wireless communication fast, secure and easy. It supports business-grade secure encryption -
802.1X and Wi-Fi Protected Access (WPA and WPA2) ; by pushing a purposely built button, the 4ipWES (Press-n-Connect) feature makes it easy to bridge wireless links of multiple OWL530s for forming a wider wireless network coverage.
EAP210 or OWL530 also features multiple ESSIDs with VLAN tags and multiple Virtual APs; great for enterprise applications, such as separating traffic from different departments using different ESSIDs. The PoE LAN port is able to receive power from Power over Ethernet (PoE) sourcing devices. Its
It is recommended to keep the original
packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.
metal case is IP68, which means that the is well suited to WLAN deployment in industrial environments.
This Quick Installation Guide provides instructions and reference materials to get you started with 4ipnet EAP210 or OWL530.
- 1 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Hardware Overview of EAP210
Front Panel
Figure 1 EAP210 Front Panel
Rear Panel
1 (1) 2 3
5
6
7
1 (2)4
Figure 2 EAP210 Rear Panel
- 2 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
1 Antenna
Connector
Reverse SMA connectors for attaching antennas. 1 (1) is the primary antenna connector and 1 (2) is the secondary. Utilize both connectors for 802.11n MIMO optimized performance.
2
12V 2A
3 Uplink Port
Power Socket for the power adaptor. The port for uplink connection to another gateway or device. PoE (802.3af/at) is supported.
4 WES Button
WDS Easy Setup. Press the button to build up a WDS link with another peer. 4 WDS links can be set up.
5 Restart Button
Press to restart the system
6 LED Indicators Power
Status WLAN WES
On indicates power on. On indicates the system is ready. On indicates wireless network interface is ready for service. For indicating WDS connection status.
Master (Press for more than 3 seconds) LED (Green) OFF and then
WES Start
BLINKING SLOWLY
Slave (Press once and then release right away) LED (Green) BLINKS SLOWLY
7 Console Port
WES Negotiate
WES Success LED (Green) ON LED (Green) ON WES Fail/Timeout LED (Green) OFF LED (Green) OFF
BLINKING SLOWLY (Green)
To access EAP210 via the console interface
BLINKING RAPIDLY (Green)
Right-Side Panel
On the right side of the panel there is a Kensington slot. Admin can also fill it with a rubber plug.
- 3 -
Quick Installation Guide
H
H
EAP210 or OWL530 Enterprise Access Point ENGLISH
ardware Overview of OWL530
OWL530
1 Ventilation Valve Due to extreme weather conditions, water vapor in the OWL530
2 Ground Connector For connecting the ground wire. 3 PoE Connector For connecting to the Power Sourcing Equipment (PSE). 4 N-type Connector x 2 For connecting to an antenna
Parts
may condense. The valve allows ventilation to prevent moisture buildup within the OWL530.
4 (1) is the primary antenna connector and 4 (2) is the secondary. Utilize both connectors for 802.11n MIMO optimized performance.
5 Detachment Tool For detaching the RJ45 connector from the PoE Port 6 Pole Mount Kit Includes two U-shaped bolts, 8 hex nuts and 8 split washers 7 Ground Wire For ground connection as mentioned in 2
ardware overview of OWL530
OWL530
Copyright © 4IPNET, INC. All rights reserved.
- 4 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
The following diagram is a basic network topology which can be used for testing and configuring the OWL530.
Installation Steps: Step 1. Connect two N-type antennas to the N-type connectors
Step 2. Connect one end of an Ethernet cable to the PSE (POWER & DATA OUT) to the PSE and one end
to the OWL530.
Inserting the RJ45 connector to the OWL530
- Unscrew the cap on the PoE Port (C)
- Insert the RJ45 cable through the outer opening of cap (C)
- Insert the RJ45 connector and wrap (A) around t he Ethernet cable through the slit between the connector and cap (C)
Copyright © 4IPNET, INC. All rights reserved.
- 5 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
- Wrap (B) around (A) through the slit on (B)
- Insert Parts (A) and (B) together into the PoE Port
Copyright © 4IPNET, INC. All rights reserved.
- 6 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
- Screw cap (C) onto the PoE Port
Step 3. Connect one end of another Ethernet cable to the PSE (Data Link) and the other end to a computer. Step 4. Connect the power cord to the PSE. Step 5. Power on the PSE in order to supply power to the OWL530.
Note:
Please do NOT remove or tamper with the ventilation valve as it has been pre-installed and secured.
Mounting the OWL530
The diameter of poles mountable by the OWL530 mounting kit is from 40mm ~ 60mm
Step 1. Screw nuts onto the U-shaped bolts and insert bolts through the split washers.
Step 2. Align the front of OWL530 with the pole and insert the U-shaped bolts into the 4 holes on the corners
of the OWL530.
Copyright © 4IPNET, INC. All rights reserved.
- 7 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Step 3. Secure the OWL530 by screwing on the nuts after the inserting the washers for all four corners.
Copyright © 4IPNET, INC. All rights reserved.
- 8 -
Quick Installation Guide
B
EAP210 or OWL530 Enterprise Access Point ENGLISH
asic setting of EAP210 or OWL530
4ipnet EAP210 or OWL530 supports web-based configuration. It is required to follow the respective installation procedures provided to properly set up the desired mode for this system.
Default IP Address of Web Management Interface: The default IP address and Subnet Mask for the AP is as follows:
Mode AP Mode
IP Address
Subnet Mask
Step 1: IP Segment Setup for Ad ministrator PC
Set a static IP address on the same subnet mask as the AP in TCP/IP of the administrator PC, such as the following example. Do not duplicate the IP address used here with the IP address of the APor any other
192.168.1.1
255.255.255.0
devices within the same network.
>> Example of IP Segment:
The valid range of IP address is 1 ~ 254. However, 1 must be avoided as it is already used by the AP. Below depicts an example of using 100 (the underlined value can be changed as desired).
IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0
Step 2: Launch Web Browser
Launch a web browser to access the web management interface of AP mode by entering the default IP address, http://192.168.1.1/, in the URL field, and then press Enter.
Copyright © 4IPNET, INC. All rights reserved.
- 9 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Step 3: System Login
The system manager Login Page will then appear. Enter “admin” in the User name field and “admin” in the Password field, and then click Login to log in.
Copyright © 4IPNET, INC. All rights reserved.
- 10 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Step 4: Login Success
After a successful login to EAP210 or OWL530, a System Overview page of web management interface will appear, To logout, simply click on the Logout button at the upper right hand corner of the interface.
Note:
AP mode is the default mode. The administrator must access the system via the AP mode login page first before switching modes.
Copyright © 4IPNET, INC. All rights reserved.
- 11 -
Quick Installation Guide
Common Settings
Step 1: Mode Confirmation
EAP210 or OWL530 Enterprise Access Point ENGLISH
Ensure the Operating Mode is currently in AP mode. Click on the Status button and then select the System Overview tab. The Operating Mode is at the
System section on the System Overview page.
Copyright © 4IPNET, INC. All rights reserved.
- 12 -
Quick Installation Guide
EAP210 or OWL530 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
- 13 -
Quick Installation Guide
Step 2: Change Password
EAP210 or OWL530 Enterprise Access Point ENGLISH
Click on the Utilities button and then select the Password tab. Enter a new password in the New Password field and retype it in the Re-enter New Password field.  Click SAVE to save the changes.
Copyright © 4IPNET, INC. All rights reserved.
- 14 -
Quick Installation Guide
Step 3: Network Settings
EAP210 or OWL530 Enterprise Access Point ENGLISH
Example Settings
Click on the System button and then select the Network Interface tab. Click the Static radio button and enter the related information in the fields marked with red asterisks. Click SAVE to save the settings.
Copyright © 4IPNET, INC. All rights reserved.
- 15 -
Quick Installation Guide
Step 4: SSID Settings
EAP210 or OWL530 Enterprise Access Point ENGLISH
Click on the Wireless button and select the General tab. Band: Select an appropriate band fro m the drop-down list box.
Click on the Wireless button and select the VAP Config tab. ESSID: Enter respective ESSID for each VAP in the ESSID field or use the default. ESSID (Extended
Service Set Identifier) is a unique identifier used for networking devices to get associated with th AP.
Click SAVE to save the settings.
Copyright © 4IPNET, INC. All rights reserved.
- 16 -
Quick Installation Guide
Step 5: Security Settings
EAP210 or OWL530 Enterprise Access Point ENGLISH
Click on the Wireless button and then select the Security tab. Select the desired VAP Profile and Security Type from the drop-down list boxes. The system supports
various WiFi standard security such as WEP, WPA Personal, WPA Enterprise, and 802.1X. The above figure depicts an example of selecting VAP-1 and WEP.
Enter the information required in the blank fields.  Click SAVE to save all settings configured so far; all updated settings will take effect upon reboot.
Congratulations!
The EAP210 or OWL530 is now successfully configured.
After OWL530's network configuration completes, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments.
It is strongly recommended to make a backup copy of configuration settings. For further configuration and backup information, please refer to the User’s Manual.
Copyright © 4IPNET, INC. All rights reserved.
- 17 -
P/N: V10020140626
Loading...