This document will support you during the use of the 3M™ Portable Labeler PL150 handheld printer. Read these
warnings carefully and use the product as described in this user guide to avoid accidental injury or damage.
The following table provides brief descriptions of the symbols and labels used with this product and its documentation.
Warning Symbol Images
DANGER
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING
CAUTION
NOTICE
Device Label Safety Information
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury and/or property damage.
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury and/or property damage.
This is how important information is shown for proper handling of device.
Only for indoor use.
Power supply unit (PSU) is double insulated.
LI Battery - Lithium cells must be completely discharged before disposal.
Battery Directive - Don't throw into the normal domestic waste.
WEEE - Don't throw this product into the normal domestic waste!
General Information
CE mark according EMC Directive 2004/108/EC
GS Mark Safety Tested
5
Intended Use
The 3M™ Portable Labeler PL300 is a portable label printer intended for industrial use. The printer is powered using a
rechargeable battery pack and 110V-240V power adapter. It can also be powered by six AA alkaline batteries. The
printer is approved for use only in closed rooms and dry environments.
WARNING
To reduce the risks with all residual hazards:
Read, understand, follow and retain for future reference all safety statements in this user guide.
To reduce the risks associated with short circuit, fire and/or electrical shock, which if not avoided, could result in serious
injury or death and/or property damage:
Do not use the PSU (Power Supply Unit) when damaged.
The PSU shall only be connected to a mains voltage of 110-240VAC/50-60Hz via a main socket which is fused.
Other usage as described for the intended use could cause damage to the product and/or hazards, for example, short circuit,
fire, electric shock.
Do not modify the PSU.
Do not use the device and PSU outdoors or in a wet environment.
Do not operate with a damaged cord or plug. Replace power supply immediately.
Do not disassemble; don't try to repair the product. Only authorized people should do this. The product is not foreseen for any
servicing. Incorrect reassembly may result in electric shock or fire.
To reduce the risks associated with explosion and/or risk of fire, which if not avoided, could result in serious injury or
death:
Do not operate in an explosive atmosphere.
CAUTION
To reduce the risks associated with misuse, which if not avoided, may result in minor or moderate injury and/or property
damage:
Do not press the cutter button if no label cassette is inserted. Be careful when cleaning the cutter blade.
To reduce the risks associated with environmental contamination, which if not avoided, may result in minor or moderate
injury and/or property damage:
Remove the batteries if the printer will not be used for a long period of time.
Dispose of device and/or batteries at end of life in accordance with local regulations. Refer to the environmental information
included in this User Guide.
6
Safety Precautions for Lithium-Ion Rechargeable Battery Pack
Inaccurate handling of a Lithium-ion rechargeable battery may cause leakage, heat, smoke, an explosion, or fire. This
could cause deterioration of performance or failure. This may also damage the protection device installed in the battery
pack. This could damage equipment or injure users. Thoroughly follow the instructions below.
While Charging the Battery Pack
DANGER
To reduce the risks associated with fire and explosion, which if not avoided, could result in serious injury or death:
Danger of explosion if a battery is incorrectly handled, charged, disposed or replaced. Replace only with the same or equivalent
type recommended by 3M™.
When charging the battery, use dedicated chargers and follow the specified conditions.
Do not connect directly to an electric outlet or cigarette lighter charger.
Do not store the battery close to fire or at extremely high temperatures over 60°C (for example, a vehicle, strong direct
sunlight).
Do not short-circuit the batteries under any circumstances.
Never charge batteries near highly flammable objects.
WARNING
To reduce the risks associated with fire and explosion, which if not avoided, could result in serious injury or death and/or
property damage:
Stop charging the battery if charging is not completed within the specified time.
Never leave the batteries unattended during charging. Do not attempt to charge a cell that is damaged.
Immediately remove the battery from the device or battery charger and stop use if the battery gives off an odor, generates heat,
becomes discolored or deformed, or in any way appears abnormal during use.
CAUTION
To reduce the risks associated with various hazards, which if not avoided, may result in minor or moderate injury and/or
property damage:
Thoroughly read this User Guide before charging the battery.
Lithium cells must be completely discharged before disposal.
Always dispose the batteries in a manner consistent with local, regional and national regulation.
Battery can only be charged within a temperature range of 0°C~45°C.
While Discharging the Battery Pack
WARNING
To reduce the risks associated with fire and explosion, which if not avoided, could result in serious injury or death and/or
property damage:
Use the battery only in the specified equipment.
Do not discharge the battery close to fire or at extremely high temperatures over 60°C (for example, a vehicle, strong direct
sunlight).
CAUTION
To reduce the risks associated with various hazards, which if not avoided, may result in minor or moderate injury and/or
property damage:
Battery can only be used within a temperature rage of -20°C~60°C.
7
4
3
7
5
6
8
9
10
11
12
14
15
17
16
18
19
20
21
22
23
21
13
1 Power connector9 Return17 Space bar
2 Label exit slot10 Favorites18 Alt
Figure 1 3M™ Portable Labeler PL150
3 LCD Display11 Add/Remove19 Hot Keys
4 Cutter button12 Custom/Settings20 Clear
5 Print13 Serial/Feed21 Escape
6 OK 14 Library/Save22 Power
7 Navigation15 Size/Styles23 Backlight
8 Backspace16 Caps
8
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.