3M CFS2507 User Manual
3M™ Water Filtration Products
SPEC#
QUANTITY
application:
DROP-IN REPLACEMENTS
models:
19 1/2” Cartridges
The 3M line of drop-in cartridges are an economical way to help
reduce constituents in water that can cause equipment damage
and unappealing product. Media choices of graded porosity, charge
modified, activated carbon and pleated polypropylene provide a wide
range of particulate holding capacities, chlorine reduction capabilities
and micron ratings. These cartridges can be used in the 3M Water
Filtration Products premium line of drop-in housings or as retrofits to
upgrade current filtration.
PRODUCT SPECIFICATIONS
Model
Number
CFS8504-B 55847-05 10 Particulate Reduction 12 (45.4) Uniform Density 1
CFS110 56121-11 5 Particulate Reduction 8 (30.3) Progressive Porosity 2
CFS124 56212-05 25 Course Particulate Reduction 6 (22.7) Progressive Porosity 2
CFS420IMF 55609-01 5 Particulate, Scale Inhibition 8 (30.3) Graded Density Polyphosphate 2
CFS2502 55603-18 0.6 Cyst Reduction 6 (22.7) Pleated Membrane 1
CFS2507 55757-04 5 5 Micron Absolute Particulate Reduction 6 (22.7) Pleated Membrane 1
CFSFSR-5 55603-20 5 Absolute Fine Silt Reduction 6 (22.7) Pleated Polypropylene 1
CFSFSR-10 55603-21 10 Absolute Fine Silt Reduction 6 (22.7) Pleated Polypropylene 1
CFS117 55593-04 5 Chlorine Taste and Odor Reduction 3 (11.4) Granular Activated Carbon 2
CFS117-S 55594-12 5 Chlorine Taste and Odor Reduction, Scale Inhibition 3 (11.4) Granular Activated Carbon Polyphosphate 2
Part
Number
Micron
Rating
Claims
Flow Rate
gpm (lpm)
Type
Qty
Req’d
3M Housings
CFS12
CFS02
CFSBCI-2
CFSBCI-3
SPEC#
QUANTITY
MODEL NUMBER
PART NUMBER
3M™ Water Filtration Products19 1/2” Cartridges
IMPORTANT: INSTALLATION TIPS
These installation tips are for informational purposes only and are not intended to be
used as actual installation instructions. CAUTION: To reduce the risk associated with
property damage due to water leakage:
•Read and follow Use Instructions before installation and use of this system.
•InstallationanduseMUST comply with all state and local plumbing codes.
•Protect from freezing, remove filter cartridge when temperatures are expected to drop
below 40°F (4.4°C).
•Do not install on hot water supply lines. The maximum operating water temperature
of this filter system is 100°F (37.8°C).
•Do not install where water hammer conditions may occur. If water hammer conditions
exist you must install a water hammer arrester. Contact a plumbing professional if you are
uncertain how to check for this condition.
•ThedisposableltercartridgeMUST be replaced every 12 months, at the rated capacity
or if a noticeable reduction in flow rate occurs.
WARNING: To reduce the risk associated with the ingestion of
contaminants:
• Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
Systems certified for cyst reduction may be used on disinfected water
that may contain filterable cysts. EPA Establishment #070595-CT-001
3M Purification Inc. recommends regularly scheduled maintenance and
replacement of the filter cartridge(s) in order for the product to perform as
advertised/sold. 3M Purification Inc. shall not be liable for system failures
due to improper maintenance.
3M is trademark of 3M Company.
© 2012 3M Company. All rights reserved.
70020193796 REV 0812B
Please recycle. Printed in U.S.A.
3M Purification Inc.
400 Research Parkway
Meriden, CT 06450 U.S.A.
Toll Free: 866.990.9785
Worldwide: 203.237.5541
Fax: 203.238.8701
www.3Mfoodservice.com
www.3Mpurification.com
Loading...