3M 7000001322 User Manual

Instructions and Parts List

3M-Matic™ Accuglide™ 2+

Type 10500

Upper and Lower

Standard Taping Heads

3 Inch

3M-Matic
Page i

Serial #:

Important Safety Information

BEFORE INSTALLING OR OPERATING THIS EQUIPMENT
Read, understand and follow all safety and operating instructions.

Spare Parts

It is recommended you immediately order the spare parts listed in the “Spare
Parts/Service Information” section. These parts are expected to wear through
normal use, and should be kept on hand to minimize production delays.

™

Accuglide 2+ - 3 Inch Taping Head

For reference, record machine serial number here.

NA - ENG

April 2017

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page ii

NA - ENG

April 2017

Replacement Parts and Service Information

To Our Customers:

This is the 3M-Matic
It has been set up and tested in the factory with Scotch® Tapes.

Included with each machine is an Instructions and Parts List manual.

Technical Assistance / Replacement Parts and Additional Manuals:

™

/AccuGlide™/Scotch® equipment you ordered.

F

or technical assista

nce, contact our help line at 1-800-328-1390.
Provide the customer support coordinator with the model/machine name,
machine type, and serial number that are located on the identi cation plate
(For example: Model - Accuglide 2+ (3 inch) Taping Head - Type 10500 - Serial Number 13282).

To order replacement parts, contact us:

CSPD division of Combi Packaging Systems LLC.
5365 East Center Dr. N.E.

Canton,OH 44721

1-800-344-9883

e-mail: [e-mail]
www.combi.com

Identi cation Plate

For Commercial Use Only

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page iii

NA - ENG
April 2017

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page iv

NA - ENG
April 2017

Replacement Parts and Service Information (continued)

To Our Customers:

™

This is the 3M-Matic
and tested in the factory with Scotch® tapes.

Included with each machine is an Instructions and Parts List Manual.

Service, replacement parts, and additional manuals available direct from:

/AccuGlide™/Scotch® equipment you ordered. It has been set up

Order parts by part number, part description, and quantity required.
Also, when ordering parts or additional manuals, include model/machine name,
machine type, and serial number that are located on the identi cation plate.

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page v

NA - ENG
April 2017

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page vi

NA - ENG
April 2017

Table of Contents - Manual 2: Accuglide 2+ Standard - 3 inch

(Upper and Lower Taping Heads)

Accuglide 2+ Standard Taping Head Manual - 3 inch Page

Cover Page

Replacement Parts and Service Information . . . . . . . . . . . . . . . . . . . . . i – ii

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii – v

Equipment Warranty and Limited Remedy . . . . . . . . . . . . . . . . . . . . . . . . . vii

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Taping Head Contents / How to Use Manual . . . . . . . . . . . . . . . . . . . . . . . 3

Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

Speci cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Dimensional Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Receiving and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Tape Leg Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Tape Width Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11

Tape Loading – Upper Taping Head . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Tape Loading – Lower Taping Head . . . . . . . . . . . . . . . . . . . . . . . . 10-11

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13

Blade Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Blade Guard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Blade Oiler Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Applying/Bu ng Roller Replacement . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15

Tape Latch Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Tape Drum Friction Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Applying Mechanism Spring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

One-Way Tension Roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Tape Leg Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Leading Tape Leg Length Adjustment . . . . . . . . . . . . . . . . . . . . 16

Changing Tape Leg Length - 70 to 50 mm [2-3/4 to 2 Inch] 16

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18

Spare Parts/Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Recommended Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Replacement Parts and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . 19-20

Replacement Parts Illustrations and Parts List . . . . . . . . 21-End of Manual

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page vii

NA - ENG
April 2017

Warranty

Warranty

Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY,
THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND
ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING,
A CUSTOM OR USAGE OF TRADE:

3M sells its 3M-Matic™ Accuglide 2+ Taping Head Type 10500

with the following warranties:

1. The Taping Head blade, springs and rollers will be free from defects in material and
manufacture for ninety (90) days after delivery.

2. All other Taping Head parts will be free from defects in material and manufacture for
three (3) years after delivery.

If any part is defective within this warranty period, your exclusive remedy and 3M’s and
seller’s sole obligation shall be, at 3M’s option, to repair or replace the part. 3M must
receive actual notice of any alleged defect within a reasonable time after it is discovered,
but in no event shall 3M have any obligation under this warranty unless it receives such
notice within  ve (5) business days after the expiration of the warranty period.
All notices required hereunder shall be given to 3M solely through the 3M-Matic™ Help
line. To be entitled to repair or replacement as provided under this warranty, the part
must be returned as directed by 3M to its factory or other authorized service station
designated by 3M. If 3M is unable to repair or replace the part within a reasonable time
after receipt thereof, 3M, at its option, will replace the equipment or refund the purchase
price. 3M shall have no obligation to provide or pay for the labor required to remove any
part or equipment or to install the repaired or replacement part or equipment. 3M shall
have no obligation to repair or replace those parts failing due to normal wear, inadequate
or improper maintenance, inadequate cleaning, non-lubrication, improper operating
environment, improper utilities, operator error or misuse, alteration or modi cation,
mishandling, lack of reasonable care, or due to any accidental cause.

Limitation of Liability: Except where prohibited by law, 3M and seller will not be liable
for any loss or damage arising from this 3M equipment, whether direct, indirect, special,
incidental, or consequential, regardless of the legal theory asserted, including breach of
warranty, breach of contract, negligence, or strict liability.

Note: The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability

may be changed only by a written agreement signed by authorized representatives
of 3M and seller.

AccuGlide™, Scotch™, and 3M-Matic™ are Trademarks of 3M, St. Paul, Minnesota 55144-1000

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page viii

NA - ENG
April 2017

Intended Use

The intended use of the AccuGlide™ 2+ Upper and Lower Taping Heads - 3 inch is to
apply a “C” clip of Scotch® pressure-sensitive  lm box sealing tape to the top and/or
bottom center seam of regular slotted containers. These taping heads are incorporated
into most standard 3M-Matic™ case sealers. The compact size and simplicity of the
taping head also makes it suitable for mounting in box conveying systems other than
3M-Matic™ case sealers. This includes replacement of other types of taping, gluing or
stapling heads in existing case sealing machines. The AccuGlide™ 2+ Upper and Lower
Taping Heads - 3 inch have been designed and tested for use with Scotch
sensitive  lm box sealing tape.

®

pressure-

AccuGlide™ 2+ STD 3 Inch Upper Taping Head, Type 10500

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 1

NA - ENG
April 2017

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 2

NA - ENG
April 2017

Taping Head Contents

AccuGlide™ 2+ Standard - 3 inch Upper and Lower Taping Heads consist of:

Qty. Part Name

1 Taping Head Assembly
1 Tape Drum and Bracket Assembly
1 Hardware and Spare Parts Kit
1 Threading Tool

General Information

This instruction manual covers safety aspects, handling and transport, storage, unpacking,
preparation, installation, operation, set-up and adjustments, technical and manufacturing
speci cations, maintenance, troubleshooting, repair work and servicing, electric diagrams,
warranty information, disposal (ELV), a glossary with a de nition of symbols, plus a parts
list of the 3M-Matic™ Accugllide 2+ (3 inch) 3M Industrial Adhesives and Tapes Division
3M Center, Bldg. 220-5E-06 St. Paul, MN 55144-1000 (USA) Edition April 2017/
Copyright 3M 2017. All rights reserved The manufacturer reserves the right to change
the product at any time without notice.

How to use this Manual

The manual is an important part of the machine; all information contained herein is
intended to enable the equipment to be maintained in perfect condition and operated
safely. Ensure that the manual is available to all operators of this equipment and the
manual is kept up to date with all subsequent amendments. Should the equipment be
sold or disposed of, please ensure that the manual is passed on with the machine.
Electrical and pneumatic diagrams are included in the manual. Equipment using PLC
controls and/or electronic components will include relevant schematics or programs in
the enclosure (or will be delivered separately as needed)

Keep the manual in a clean and dry place near the machine. Do not remove, tear or
rewrite parts of the manual for any reason. Use the manual without damaging it.
However, if the manual has been lost or damaged, ask your after sale service for a
new copy (if it is possible, please have the manual name, part number, and revision
information and/or model/machine name, machine type, and serial number) that
are located on the identi cation plate:

(For example: Model - Accuglide 2+ - 3” - Type 10500 - Serial Number 13282).

Note: All the important warning notes related to the operation of the machine are
identi ed by the symbol:

Updating the Manual

Modi cations to the machine are subject to manufacturer’s internal procedures.
The user may receive pages or parts of the manual which contain amendment made
after its  rst publication. The user must use them to update this manual.

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 3

NA - ENG
April 2017

Important Safeguards

Explanation of Signal Word and Possible Consequences

This safety alert symbol identi es important messages in this

manual. READ AND UNDERSTAND THEM BEFORE INSTALLING OR
OPERATING THIS EQUIPMENT.

Caution

Warning

WARNING

• To reduce the risk associated with
mechanical hazards

­Read, understand and follow all safety

and operating instructions before
operating or servicing the case sealer

− Allow only properly trained and

quali ed personnel to operate
and or service this equipment

Indicates a potentially hazardous situation, which,
if not avoided, may result in minor or moderate injury
and/or property damage.

Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury and/or
property damage.

CAUTION

• To reduce the risk associated with
muscle strain:

- Use proper body mechanics when

removing or installing taping heads
that are moderately heavy or may be
considered awkward to lift

• To reduce the risk associated with
impact hazards

- Place the taping head on a smooth

level surface when maintaining or
servicing this equipment

WARNING

• To reduce the risk associated with

shear, pinch, and entanglement hazards

- Turn air and electrical supplies o

on associated equipment before
performing any adjustments, mainte­ nance, or servicing the taping heads

- Never attempt to work on the taping

head or load tape while the box drive
system is running

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 4

WARNING

• To reduce the risk associated with
sharp blade hazards:

- Keep hands and  ngers away from
tape cuto blades under orange blade
guards. The blades are extremely sharp.

(Important Safeguards continued on next page)

NA - ENG
April 2017

Important Safeguards (continued)

Important - In the event the following safety labels are damaged or destroyed,
they must be replaced to ensure operator safety. See "Replacement Parts
Illustrations and Parts Lists" for label part numbers.

78-8133-9606-2
Tape Threading Label

(Not shown)

Figure 1-1 Replacement Labels/3M Part Numbers

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 5

NA - ENG
April 2017

Speci cations

1. Tape:

For use with Scotch® pressure-sensitive  lm box sealing tapes.

2. Tape Width:

48mm [2 inches] minimum to 72mm [3 inches] maximum.

3. Tape Roll Diameter:

Up to 405mm [16 inches] maximum on a 76.2mm [3 inch] diameter core.
(Accommodates all system roll lengths of Scotch®  lm tapes.)

4. Tape Application Leg Length - Standard:

70mm ± 6mm [2-3/4 inches ±1/4 inch]

Tape Application Leg Length - Optional:

50mm ± 6mm [2 inches ± 1/4 inch] (See “Adjustments – Tape Leg Length.”)

5. Box Size Capacities:

For use with center seam regular slotted containers.

Minimum Maximum
Length – 150mm [6 inches] Unlimited
Height – 120mm [4-3/4 inches] (most “3M-Matic” Case Sealers)
90mm [3-1/2 inches] (with optional 2 inch leg length)
Width – 150mm [6 inches]

When upper and lower taping heads are used on “3M-Matic” case
sealers, refer to the respective instruction manual speci cations for
box weight and size capacities.

Limited by
Case Sealer

6. Operating Rate:

Conveyor speeds up to 0.38 m/s [75 feet per minute].

7. Operating Conditions:

Use in dry, relatively clean environments at 5° to 40°C [40° to 105°F] with clean dry boxes.

Important – Taping heads should not be washed down or subjected to conditions causing
moisture condensation on components.

8. Taping Head Dimensions:

Length – 457mm [18 inches]
Height – 560mm [22 inches] (with tape drum)
Width – 130mm [5-1/8 inches] (without mounting spacers)
Weight – Packaged: 8.2 kg [18 lbs.] Unpackaged: 7.3 kg [16 lbs.]

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 6

(Speci cations continued on next page.)

NA - ENG
April 2017

Speci cations (continued)

13 mm
[1/2 in.]

396 mm
[15-19/32 in.]

130mm (5 1/8)

58 mm
[2 9/32 in.]

278 mm
[10-15/16 in.]

405 mm

18 mm [11/16 in.]

445 mm
[17-1/2 in.]

3M-Matic™ Accuglide 2+ - 3 Inch Taping Head
Page 7

18 mm [11/16 in.]

405 mm

Figure 2-1 Dimensional Drawing

NA - ENG
April 2017