3M 3M034-030-TNG, 3M034-3-TNG, 3M034-031-TNG User Manual

3M™ EM Aware TNG ESD Event Monitor

Models 3M034-3-TNG, 3M034-030-TNG and 3M034-031-TNG

User’s Guide

Read, understand and follow all safety information contained in these user guide

instructions prior to installation of the 3M™ EM Aware TNG ESD Event Monitor.

Retain these instructions for future reference.

Intended Use

The 3M EM Aware TNG ESD Event Monitor monitors up to four key parameters

that keep you aware of critical symptoms of ESD problems: 1) ESD events; 2)

static voltages; 3) ionization balance; and 4) charge decay. The thresholds for these

parameters are fully adjustable to suit your needs. The improved design features a

metal case module with built-in LCD display, a control joystick, remote antenna,

power supply and a data output.

The monitor system must be installed as speciﬁed in this user’s guide. It is intended

for use in the following environmental conditions only:

1. Indoor use

2. Altitudes up to 2,000 meters above sea level

3. Temperature range of 10ºC to 40ºC

4. Maximum relative humidity of 80% for temperatures up to 31ºC, decreasing linearly to 50% relative humidity at 40ºC

5. Pollution degree two (ofﬁce, laboratory, test station)

The monitor system has not been evaluated for other uses or locations. If the monitor

is used in a manner not speciﬁed by 3M, the protection provided by the equipment

may be impaired.

3M™ EM Aware TNG ESD Event Monitor

Safety Statements

EXPLANATION OF SIGNAL WORD CONSEQUENCES

WARNING:

CAUTION:

NOTICE:

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or property damage.

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury and/or property damage.

Indicates a potentially hazardous situation, which, if not avoided, may result in property damage.

EXPLANATION OF PRODUCT SAFETY LABEL SYMBOLS

Indicates DC (Direct Current)

Earth Ground

Important safety information, refer to the user manual.

WARNING:

To reduce the risks associated with hazardous voltage, which if not avoided, could result in death or serious injury:

• Do not modify or disassemble this product;

• Never allow children or other non-qualiﬁed persons to come into contact with power adapter;

• Never use power adapter outdoors or other wet locations;

• Always use extreme caution to avoid coming into contact with any exposed electrical conductors of the equipment being monitored with the EM Aware TNG ESD Event Monitor.

To reduce the risks associated with hazardous voltage or possible explosion, which if not avoided, could result in death or serious injury,

• Use only the power adapter provided with the product;

• If power adapter is missing or damaged, only replace with one supplied by 3M

CAUTION:

To reduce the risks associated with ground water contamination:

• Never incinerate or dispose of product in a manner which is inconsistent with local, state, or federal regulations

NOTICE:

To reduce the risks associated with Electrostatic Discharge (ESD) voltage, which if not avoided, could result in damage to the meter:

• To install or change antennas, turn off the meter, install or change antennas, turn meter back on;

• Avoid touching antenna when meter is turned on.

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN IRREVERSIBLE DAMAGE TO EM AWARE TNG AND HARM TO PERSONNEL AND EQUIPMENT:

• If the 3M™ EM Aware TNG ESD Event Monitor is connected to a facility monitoring system (FMS), always verify that there is zero voltage and low resistance between FMS ground and ground at the location where EM Aware TNG monitor is installed and is being grounded. If ground conditions are unacceptable, correct them ﬁrst prior to installing the EM Aware TNG monitor. Otherwise, damage to the EM Aware TNG monitor and/or to the FMS may occur.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la NMB-003 du Canada.

+ 8 hidden pages